SPECIAL REPAIRS TO BLDG NO. T-213 (TDN SHOP) AT GRC KAMPTEE.

Amount

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed

M&L for machine cut kota stone slab flooring 20 to 25mm thick laid over and including 20mm thick cement mortar 1:6 screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc, complete all as specified and directed.

M&L for Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed/backing coat 15mm thick in CM 1:4 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc, complete all as specified and directed.

Demolition of plain cement concrete in ground floor & paving not exc 15 cm thick (above or below ground level) etc, complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub-base, under floors and pavings etc, complete all as specified and directed.

Material & labour PCC (1:3:6) Type C1 (using 20 mm graded stone aggregate), 75 mm thick as in plinth protection and finishing surfaces even & smooth without using extra cement including mist filling in the joint etc, complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B1 (20 mm aggregate ) as in PCC path and similar works etc, complete all as specified and directed.

Taking down cement plaster, any desription on brick or stone walls including raking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed.

Dismantling of brick work or stone/boulder masonary built in cement mortar including ashalar facing dressed stoen and pre-cast concrete articles etc, complete all as specified and directed.

M & L for brick work with flyash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6(Using old size brick) etc, complete all as specified and directed.

Material & labour for Rendering 15 mm thick in CM 1:4 on brick or concrete surfaces using water proofing liquid compound as per manufacturer instructions, and finishing surfaces even & smooth without using extra cement etc, complete all as specified and directed.

Material & labour for Rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement etc, complete all as specified and directed.

Material & labour for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of cement primer etc, complete all as specified and directed.

Material & labour for preparation of old plastered surfaces of wall & applying two coats of cement base paint etc, complete all as specified and directed.

M & L for preparation of new surfaces of wall & applying two coats of oil emulsion distemper over a coat of birla white wall care putty etc, complete all as specified and directed.

M & L for complete removal of existing treatment of surfaces of wall & applying two coats of oil emulsion distemper over a coat of birla white wall care putty etc, complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of white wash on walls etc, complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of white wash on walls etc, complete all as specified and directed.

M&L for Preparation of old wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint etc, complete all as specified and directed.

M & L for preparation of old steel surafces of any description over 10 cm width or girth & applying two caots of synthetic enamel paint etc, complete all as specified and directed.

M&L for preparation of new wooden surfaces of any desription over 10 cm width or girth & applying two coats of synthetic enamel piant over coat of primer etc, complete all as specified and directed.

M & L for preparation of new steel surafces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint etc, complete all as specified and directed.

Dismantling of asbestos cement/transculent sheet corrugated/ semi-corrugated sheets in roof coverings incl ridges etc, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws etc, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws etc, complete all as specified and directed.

Material & labour plain cement concrete Type 1:2:4 B0 (using 12.50 mm graded stone aggregate) as in coping, haunching rounded or chamfered on edges including necessary from work etc, complete all as specified and directed.

Dismantling of wall and ceiling board (fibre,insulation etc) or insulation board, slabs, blankets, any thickness incl cover fillets etc, complete all as specified and directed.

M&L for non-asbestos designer fiber cement building boards of size 595x595x4mm fixed or laid/inserted to GI frame work with screws/clips as in ceiling laid flat or sloping etc, complete all as specified and directed. Note : GI frame work will be measured and paid for separately.

Providing and fixing snap grid for false ceiling of size 595 x 595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanised steel sections @ 90 grams/ sqm both side inclusive, consisting of main 'T' runner with suitably spaces joints to get required length and of size 24mm X 38mm made from 0.25 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross 'T' of size 24 mm x 25 mm x 1200 mm made of 0.25 mm thick (minimum) sheet, 1200mm long spaced between main 'T' at 600mm centre to centre to form a grid of 1200 x 600mm and secondary cross 'T' of length 600mm and size 24mm X 25mm X 600mm made of 0.25 mm thick (minimum) sheet to be interlocked at middle of the 1200 X 600mm panel to form grids of 600 X 600 mm and wall angle of size 24mm X 24mm X 0.4mm including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main 'T' runners to be suspended from ceiling using GI slotted cleats of size 27 X 37 X 25 X 1.0 mm fixed to ceiling with 12.5mm dia and 50m long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 X 30 X 0.5mm spaced at 1200mm c/c along main "T", bottom exposed width of 24mm of all T sections/ wall angle shall be pre-painted with polyster paint for all heights as per specifications, drawings, complete all as specified and directed.

Dismantling wrought iron or mild steel work etc, complete all as specified and directed.

S&F mild steel in wind ties for roof including securing bolts, Angle iron post and struts in fencing including cutting tops to shape as directed, drilling hole, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290(Gde E-165) etc, complete all as specified and directed.

Taking down Chowkats or frames incl. shutters (without taking of shutter from the frames) n. exc 1.50 Sqm each etc, complete all as specified and directed.

Taking down Chowkats or frames incl. shutters (without taking of shutter from the frames) exc 1.50 Sqm and not exc 4 sqm etc, complete all as specified and directed.

Taking down shutters of any description n. exc. 2.00 Sqm etc, complete all as specified and directed.

S&F steel window with side hung shutters ( glaze & gauze shutter) including projecting or box stype hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer including fixing of hold fast of size 25 x 5 mm flat iron etc, complete all as specified and directed.

Ditto all as per Item Sr No 33 above but without glazing bars etc, complete all as specified and directed.

S&F framed guard bars with mild steel Square bars with ends of bars shouldered and/ or riveted and similar work confirming to FE 410-O or FE 310-0 etc, complete all as specified and directed.

Hacking out old broken glass any thickness size and quality from wooden/steel frames etc, complete all as specified and directed.

S & F sheet glass ordinary quality, 3 mm thick and glazing with oil putty in square n. exc. 0.50 Sqm in each pane etc, complete all as specified and directed.

S & F in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc, complete all as specified and directed.

S&F factory made Plain framed panelled shutter 35 mm thick (two panel) with lock rail and panel 12 mm thick veneered particle baord with commercial veneering on both side the size of rail and stiles as per IS:1003(Part-I) kiln seasoned and chemically pressure treated etc, complete all as specified and directed.

S & F 100 mm long Mild steel medium weight cold rolled butt hinges and fixed with screw/welded to frames etc, complete all as specified and directed.

S & F Aluminium handles cast type 150 mm long, complete all as specified and directed.

S & F 150 mm long aluminium anodised, barrel tower bolt of extruded section , complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised sliding door bolts with hasp and staple (bolt type) and fiing clips of sheet, cast or extruded setions and fixing bolds and sliding bolts of extruded sections or cast aluminium alloy , complete all as specified and directed.

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10 mm dia as tle bar complete confirming to Fe-410 -O etc, complete all as specified and directed.

Taking down point wiring with aluminum conductor cable of light point fan & socket light & power complete including light fittings any type switches, sockets, ceiling rose, switch boards, bell/buzzer, bell push, tube light fitting, regulator etc, and making good to the disturbed surfaces of walls/ floor etc to match with existing surfaces including white washing/colour washing/ distemper to match with existing wall/floor/ceiling finishes, complete all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good disturbed surfaces to match with existing surfaces, complete all as specified and directed.

Taking down sub main wiring of any size/ capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces, complete all as specified and directed.

M&L point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm pressed steel modular boxes sunk on wall for mounting of modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch, complete all as specified and directed. (Cable Make : Finolex, L&T, Legrand, Havells, Polycab) (PVC Conduit Make : Polycab, Anchor, Finolex) Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth trolley

Ditto all as per item Sr. No 50 above but One ceiling /exhaust fan point controlled by one switch and regulator, complete all as specified and directed.

Ditto all as per item Sr. No 50 above but One 3 pin 5 amp socket out point on the same board with other switches, complete all as specified and directed.

Ditto all as per item Sr. No 50 above but One 3 pin 5 amps socket out let point on independent board, complete all as specified and directed.

Ditto all as per item Sr. No 50 here in before but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point, complete all as specified and directed.

M&L for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the following sizes :- 2x 4.0 Sqmm with earth wire of 1x4.0 Sqmm, complete all as specified and directed. Cable Make : Finolex, L&T, Legrand, Havells, Polycab) (PVC Conduit Make : Polycab, Anchor, Finolex Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same make.

Supply and fix ceiling rose surface type 2/3 terminal 5 amps , complete all as specified and directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular switch one way 6A, 1 module , complete all as specified and directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular switch one way 16A, 1 module , complete all as specified and directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular Socket 6A 2/3 pin combined 2 module , complete all as specified and directed. Make : Anchor Roma, Legrand, Crabtree

Supply & Fix Modular Socket 6A/ 16A 2/3 pin combined 2 module , complete all as specified and directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular Fan step regulator,120 watt 2 module, complete all as specified and directed. Make : Anchor Roma, Legrand, Crabtree

Supply and Fix Highly durable surface mounted 18/20 watts LED batten/surface constructed of fire retardant engineering grade extruded plastic and decorative end cap complete with tube rod,driver including 3 core 1.0 sqmm copper conductor cable for connection and accessories, complete all as specified and directed. Make :- CG LCTLN-20-CDL/Philips/ Luker.

Supply & fix light fitting 9W LED bulk head luminaries with lamp holders etc complete with all accessories and including connecting up with twin core twisted flexible cable suitable size of 230V, 50HZ, complete all as specified and directed. Make: CG LBHP-10-CDL/Philips/ Luker.

Supply and fix building security light LED 25 W with Lumen O/P 1800 with driver with rated voltage 240 V, 50Hz,including mounting GI (made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc, complete all as specified and directed by the Engineer-in-Charge. Make : CG LSTS-25-CDL/ Philips/ Luker.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting double dooretc, complete all as specified and directed by the Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Supply and fix MCB single pole 240 volt 6 to 40 amps 10 KA breaking capacity, 'C' series etc, complete all as specified and directed by the Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Supply and fix MCB single pole and neutral 240 volt 6 to40 amps 10 KA breaking capacity, 'C' seriesetc, complete all as specified and directed by the Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Earthing complete with galvanized street earth plate electrode 600x600x6mm thick buried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanized iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric weighting not less than 1.87 Kg/sqmm (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminum lugs etc all as specified. (e) 15mm nominal bore medium grade GI protection pipe up to 7.50 meter long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.47,930.00/- ]

M/S L M Chourasia

M/S J.A CHAWHAN

Shri Mohan Brother

M/s M.G. Hargunani

M/s. Nikhil B Nistane

M/s B S Jain

M/s DS Khekde

Meet Road Lines

Bidder Name

Meet Road Lines

M/S J.A CHAWHAN

M/S L M Chourasia

M/s B S Jain

Shri Mohan Brother

M/s DS Khekde

M/s Jagdish Staioners and General Stores

M/s M.G. Hargunani

M/s. Nikhil B Nistane