CONSTRUCTION OF OFFICE BUILDING FOR SUB DIVISION OFFICE NO.1 , ZIRA AT VILLAGE MARKHAI BLOCK ZIRA DISTRICT FEROZEPUR (Pb.) ((Under PRWSSIP Sub Component 4A

Amount

Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction including disposal of all surplus soil as directed within a lead of 30 meters.

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar up to 40% excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead up to 30 metres

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centring and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Cement Concrete 1:8:16 with brick ballast 40mm gauge. (b)Cement Concrete 1:8:16 with 40mm gauge stone aggregate (Including Carriage of Material).

Cement Concrete 1:6:12 with 40 mm gauge stone aggregate using concrete mixer . For coveering G.I. Pipe (Including Carriage of Material).

Cement concrete 1:5:10 with 40 mm stone ballast using concrete mixing volumetric type (Including Carriage of Material).

Cement Concrete 1:4:8 with stone ballast of size of 40 gauge using mechanical mixer.(cum) (Including Carriage of Material).

Cement Concrete 1:2:4 with stone ballast or shingle. (Including Carriage of Material).

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth. (Including Carriage of Material).

Reinforced cement concrete M-20 mechanicaly batch mixed using batch type concrete mxier as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in super structure. (Including Carriage of Material).

Supplying & Laying dry brick bats.

First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. (Including Carriage of Material).

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (Including Carriage of Material).

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. (Including Carriage of Material).

Extra rate for First Floor

115 mm thick brick wall with every fourth course reinforced with hoop iron laid in 1 :4 cement sand mortar in super structure (Including Carriage of Material).

First class homey comp. burnt brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (Including Carriage of Material).

Terracing consisting of tiles 22.86 x 11.43 x 3.83 cm laid over 25 mm mud plaster 7.5 cm mud filling on another laver of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg/sqm top of CC slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc. (Including Carriage of Material).

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16. (Including Carriage of Material).

Bottom Khurra on ground 1.2m x 0.6m consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3 (Including Carriage of Material).

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. (Including Carriage of Material).

Providing and fixing 110 mm dia SWR U.P.V.C Rain water pipe (ring fitted type-A) as per IS:13592 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in-charge. (If fixed on wall face clamp to be paid separatly as per respective item) (Including Carriage of Material).

Providing and fixing 110 mm dia SWR U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer-in-charge.

Providing and fixing 110 mm dia SWR U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.

Base course of floor consisting of 100 mm thick cement concrete 1:8:16 with stone aggreate and 100 mm sand filling.(using mechanical mixer for mixing of material) (Including Carriage of Material).

Kota stone tile flooring 20mm to 30 mm thick over 12.5mm thick base of cement mortar 1:3 (1 cement, 3 Sand) laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing. (Including Carriage of Material).

Kota stone tiles 20mm thick in skirting risers of steps, dado walls and pillars laid in 2.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing. (Including Carriage of Material).

Coloured Granite stone tiles 20 mm thick in skirting, risers of steps dado, walls and pillars laid in 12.5 mm thick cement mortar 1:3 (1 cement, 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing & polishing including labour for fixing dowels, pins and cramps. (Including Carriage of Material).

Providing and laying vitrified floor tiles 600x600mm size premium quality, manufactured using Soluble Salt Technology, with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 fine sand ) for new flooring laid with cement based high polymer modified quick set tile adhesive (water based) of approved make IS 15477 marked using 5 Kg adhesive per sqm of tile area in average 3mm thickness over existing base, including grouting the joints (Tiles to be laid with 2mm to 3 mm gap using spacers and later this gap to be filled with cement based grout) with Cement base grout and matching pigments etc., complete

Providing and laying Rectified Porcelain floor tiles 400 x 400 mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20 mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Fine sand) for new flooring complete Rectified tiles have finished edges allowing them to be placed closer together for a narrower grout joint as opposed to other tiles and are more expensive. Unlike typical factory-edged tile, rectified tile is cut to size after the firing process. (Including Carriage of Material).

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 250 x 330 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (Including Carriage of Material).

Providing and Laying Out Door Precast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3 (1 ordinary cement :3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer-in-charge. (Including Carriage of Material).

Providing and laying 60 min thick factory made cement concrete Interlocking paver block of M-35 grade rubber moulded smooth finish with strong vibratory process and of approved sire and design / shape laid in Ordinary Grey Colour and pattern over and Including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer in-Charge for Light Traffic Areas such as Pedestrian plazas, shopping complexes, ramps, car parks, office driveways, housing colonies, Office complexes, rural roads with low volume traffic, farm houses, beach sites, tourist resorts, local authority footways, residential roads, etc.(sqm) (Including Carriage of Material).

Providing and laying 60 min thick cement concrete Interlocking paver block of M-35 grade machine made rubber moulded smooth finish by strong vibratory process and or with vibro-hydraulic compaction machine of approved sire and design / shape laid in Dark Fast Colour and pattern over and Including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer in-Charge for Light Traffic Areas such as Pedestrian plazas, shopping complexes, ramps, car parks, office driveways, housing colonies, Office driveway, housing colonies, office complexes, rural roads with low volume traffic, farm houses, beach sites, tourist resorts, local authority footways, residential roads, etc.(sqm) (Including Carriage of Material).

Providing and fixing Morwad Marble strip 18 mm to 20 mm thick and 100 mm wide in Kotah Stone Flooring over 12.50 mm thick base of cement mortar 1:3 jointed with cement slurry including cost of additional mortar equivalent to the kotah stone thickness and colouring pigment to match the colour rubbed and polished to granolithic finish complete in all respects. (Including Carriage of Material).

12.5 mm thick cement plaster 1:2 (Including Carriage of Material).

12.5 mm thick cement plaster 1:4 (Including Carriage of Material).

12.50 mm Cement Plaster 1:5 on walls (Including Carriage of Material).

20 mm thick Cement Plaster 1:4 in two coat work. (Including Carriage of Material).

20 mm thick Cement Plaster 1:5 in two coats work. (Including Carriage of Material).

Platering on underside of Ceiling 10mm thick Cement Plaster 1:3 (Including Carriage of Material).

Bearing Plaster of 10 mm thick cement mortar 1:3 cement sand finished with a floating coat of neat cement and thick coat of Lime wash / P.O.P. on top of walls when dry for bearing of R.C.C. slabs & beams. (Including Carriage of Material).

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Painting two coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. - With ordinary quality Paint

Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface

Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two coats applied @ 1.43litre/10 sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm.

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two coats)

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish

Providing and applying pluster of paris ISI marked Punning 6mm thickness over plastered surface to perpare the surface even and smooth complete in all respects as per the directions of eng-in - incharge.

Quantity as per smooth surface

Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt)

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges:- 35 mm thick

35mm thick

Providing and fixing 12mm thick 150mm wide pelmets with 25mm dia Aluminium rod and brackets including fixing with 25mmx3mm MS Flat 10cm long and PVC Plug etc complete Deodar Wood

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete - I.S.I Designation No. III (size of door 851 mm to 1000 mm)

Providing and fixing 0.50 mm thick aluminium sheet including cost of necessary fittings i.e. screws, etc. complete

Providing and fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300 mm x 16 mm

Wrought iron and mild steel ladders, framed grills, grating etc. with ends of bars, riveted or welded or forged, framed window guards, barred iron doors, stair case, iron railing including cost of bolts and nuts or screws or welding rod, complete fixed in position.

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-2006, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete

Supply & fixing of door frames (Chowkhats) consisting frame fabricated from sheet roll formed out of 1.2 mm thick galvanized sheet as per IS:277 (base steel as per IS:513) with zinc of 120 gm/Sqm. & Powder coated with pure Polyster powder up to 50 micrones (as per approved colour), 3 Nos. 100 mm but hinges 2 mm thick, 6 Nos. 1.2 mm thick CRCA electroplated stiffner, 6 Nos. M.S. hold fast with split and tail welded to stiffner plate 200 mm long, Receiver for adrop, M.S. tie rod 50 mm x 25 mm to be fixed at bottom finished with powder coated total thickness of coating 0.60 mm of approved shade, fixed in position, including the cost of cement concrete for 1:2:4 for fixing lugs complete in all respects as per drawing, design, specification and entire satisfaction of Engineer-in-Charge.

Doors frame of size 80 mm x 50 mm with 37 mm wide single rebate for 35 mm door shutter.

Doors frame of size 125 mm x 60 mm with 37 mm wide double rebate for 35 mm door shutter.

Supply & Fixing of Window frames (Chowkhats) including mullions consisting frame fabricated from sheet roil formed out of 0.58mm thick galvanished sheet (base steel as per IS : 513) with zinc of 120grnisom steel sheet pre coated (as per approved colour) with polyster paint of 12-16 micrones thickness under coat of EPDXY primer & back coated with ALKYD backer of 5-7 micrones total thickness of coating 0.58mm of approved shade, fixed in position by means of PVC & metal hold fastner with PVC cap complete in all respects as per drawing, design, specification & entire stasfication of Enginner-in-Charge.

Windows Outer frame of size 72 mm x 55 mm and central mullion 72 mm x 50 mm with Double rebate.

Supply & Fixing of Window shutter consisting frame fabricated from sheet roll formed out of 0.58mm thick galvanished sheet (base steel as per IS : 513) with zinc of 120gm/som steel sheet pre coated (as per approved colour) with polyster paint of 12-16 micrones thickness under coat of EPDXY primer & back coated with ALKYD backer of 5-7 micrones total thickness of coating 0.58mm of approved shade, fixed in position fixed in position by means of screws complete in all respects as per drawing, design, specification & entire stasfication of EngInner-in-Charge.

Glazed Windows shutter Section 47 mm x 20 mm (Without Glass)

Wire Mesh Windows shutter Section 40mm x 20mm with S.S wire mesh 32 guage flymesh with 144 holes per square inch

Providing 8, fixing fixed beeding 12 mm x 12 mm for fixed glass with EGO fixed gasket (EPDM)

Providing and fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of Gasket /beading shall be paid as per respective item)

Float Glass panes of 5.5 mm thickness

Providing Polyster Powder coating 60 to 70 micron any coloured specrified to M.S Grill section of various sizes including carrriage of material from marktet to workshop

Construction of unreinforced plain cement concrete pavement in M-30 mix design over a prepared sub base with cement contents 350 kg per cum and coarse and fine aggregates conforming to IS:383 mixed with concrete mixer using weigh batcher, laid in position over 125 micron thick polythene sheet, compacted with needle vibrator, screed vibrator and plate vibrator, dewatering of free water with vaccum pump, finishing the surface with power floater, including provision of contraction and expansion joints as required, finishing to required lines and grades as per drawings and technical clause 1501 of MORD specifications (cum)

Boring hand-pump in soil with admixture of shingle.

Excavation by mechanical means(JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including tri mm ing and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation, watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead up to 15 meter complete in all respect.

a) Earth work up to 1.5 m. Depth for 50mm pipe line

Providing ISI Marked G.M ferrule as per IS:2692, drilling and tapping cast iron pipe lines of all diameters and screwing in Ferrule and connections complete in all respect.

f) 25 mm i/d Ferrule heavy duty

Providing, laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B-Class Premium make such as (Jindal Hisar) including cost of specials (such as tees, bends, sockets, elbows etc.), painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.

Providing and laying, jointing, fixing, testing ISI Marked G.I. Pipe (as per IS 1239) B- Class, premium make such as (Jindal Hisar) including cost of Specials such as tees, bends, sockets elbow etc., cutting, threading and testing in trenches in the ground complete.

f) 50 mm i/d

Providing, fixing and jointing G.I Union Couplings (of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.

a)15 mm i/d G.I. Union

b) 20 mm i/d G.I. Union

c) 25 mm i/d G.I. Union

e) 40 mm i/d G.I. Union

f) 50 mm i/d G.I. Union

Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete.

e) 40 mm i/d Brass Ball valves

Painting G.I. Pipes and Specials with synthetic enamel Paint in all shades as per I.S.I. specification on existing or new work, two coats paints including cleaning rubbing surface, etc.

a) 15 mm & 20 mm i/d G.I. Pipe

b) 25 mm & 32 mm i/d G.I. Pipe

c) 40 mm & 50 mm i/d G.I. Pipe

Cutting holes up to 23 cm square through B.B. in cement walls or stone masonry wall in cement for pipes, and making good the same & finishing according to existing finish where required.

a) Through wall 11.43 cm thick

b) Through wall 22.86 cm thick

Providing and fixing of FIRE EXTINGUISHER, ABC Powder type (stored pressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect.

c) 6 Kg. Capacity

Providing and fixing of FIRE EXTINGUISHER, CO2 type as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect.

c) 4.5 Kg. Capacity

Earth work in excavation for storage and sedimentation tanks, high level tanks, filter beds, clear water reservoirs, pump houses, sumps, screening chambers and other similar works having straight or open cuttings in foundations trenches etc. with 3D Excavator/ JCB including manually dressing of bed, trimming of sides and side slopes to full dimension and depth as shown on the drawings or as shall be required by Engineer-in-charge, including dressing of bottom and sides of trenches, stacking the excavated soil clear from the excavation and subsequent filling around plinth/structures including watering

Excavation in trenches with straight or open cutting in streets, lanes or in open area with 3D/JCB or excavator including manually dressing bed, tri mm ing sides and side slopes for sewers and manholes to full depths as shown in drawings, including, dressing to correct sections and dewatering, provision for diversion for traffic, protection of existing services i.e. telephone cables, electric lines, water supply lines and gas lines etc. night signals, profiles, pegs, sight rails, boning rods, watching, etc., fixing and maintenance of caution boards, fencing, refilling trenches, watering, ra mm ing and restoration of surface to original level and removal of surplus spoil from the site of works, up to one chain (15 m) complete in all respects.

B(a) For depth exceeding 3.0 m. and For Sewer line as per detail attached

Providing & fixing 560 mm, 500 mm and 450 mm internal diametre circular or 450 mm x 600 mm clear inside opening rectangular RCC manhole cover and frame ISI marked as per IS:12592-2002 including carriage from the stores of the Engineer-in-charge to site of work, loading, unloading including stacking and setting the same to correct lines over manholes including cement concrete copping (M:20) around the frame etc. Dia of steel for lifting hook is 16mm. (for EHD and HD). (A)

Providing orange colour safety footrest of minimum 6mm thick plastic encapsulated as per IS:10910 on 12mm dia steel bar confirming to IS: 1786 having minimun cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruted legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 230x150x75cm cement concrete block 1:2:4 (1 cement: 2 sand: 4 stone aggragate) complete as per design.

Construction of brick masonry inspection chambers size as given below up to 0.60 metre average depth in 1:5 cement sand mortar, lime concrete with 40 per cent lime mortar 2:3 in foundation, cement concrete 1:2:4 benching 12.50 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement, R.C.C. 1:2:4 slabs 100 mm thick cement concrete topping 50 mm thick with 455 mm x 455mm, 455 mm x 610 mm inside light duty C.I. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.

(a) Size 450 mm x 450 mm inside with RCC 455 mm x 455 mm cover and frame light duty double seal (Nos.)

Providing and fixing in position Chinaware Indian Orissa water closet size 580 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing jet spray with 2'-6" long PVC pipe with PTMT nut

Providing and fixing in position vitreous Chinaware white large flat back or angular lipped front urinal 610 mm high of approved make (to the approval of the Engineer-in-charge) (610 mm x 410 mm x 380 mm) consisting of C.P. waste 32 mm dia and C.P. brass spreader, complete.

Providing and fixing PVC waste pipe 32 mm i/d of approved make (to the approval of Engineer-in-charge) complete in all respect. Qty. same as WB + Urinal + Steel Sink

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32 mm dia with one C.P. brass pillar tap complete in all respect.

Size 550 mm x 400 mm

Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.

Providing and fixing in position stainless steel sinks of approved make 1 mm thick, grade-304 (18/8) with waste coupling complete in all respect.

Providing & Fixing in position 5 mm thick bevelled edge mirror of superior glass (of approved make) complete with 4 mm thick hard board backing fixed in with rawl plugs 50 mm , C.P. brass screws and washers complete in all respect (as required by the Engineer-in- Charge) - Size 600 mm x 450 mm.

Providing & Fixing in position C.P./ Aluminium Khunti of approved make (to the approval of Engineer-in-charge) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect - C.P. Brass khunti with 3 pegs

Providing & Fixing in position C.P. Brass flange of approved make (to the approval of Engineer-in-charge) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25 mm long to 50 mm long of approved make (to the approval of Engineer-in-charge) with various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass Hexa Nipple 15 mm of approved make (to the approval of Engineer-in-charge) complete in all respect.

a) Size 600 mm x 450 mm x 225 mm (Net size excluding flat edge)

Providing & Fixing in position 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge) complete in all respect.

i) C.P. brass Bib cock long nose/ long body without flange

ii) C.P. brass Bib cock without flange

Providing & Fixing in position stop cock / Angle valve of approved make (to the approval of Engineer-in-charge) complete in all respect. For Jet Spray Connection + Over Head Shower

c) C.P. Brass 15 mm Angle valve without flange

b) C.P. Brass 15 mm Concealed stop cock with flange.

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge) complete in all respect. (Note:-To be provided only for VIP Installations and with prior approval of the Engineer-in-charge.)

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect - PVC tube connection of size 15 mm x 375 mm with PTMT nut

Qty. same as OWC + EWC + WB + Urinal + Steel Sink

Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 of approved make (to the approval of Engineer-in-charge)including cutting, jointing, wastage, but excluding cost of lead jointing.

b) 110 mm o/d SWR UPVC pipe line laid complete (Mtr,)

c) 90 mm o/d SWR UPVC pipe line laid complete (Mtr,)

Providing and fixing in position gratings 150 mm x 150 mm on top Khura PVC grating.

Providing and fixing in position M.S. or heavy flat iron clamps made out of M.S. flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyphonage pipes to walls complete in all respects. Including cutting and making good the walls and floor etc. and painting.

Providing and fixing in position SWR UPVC specials for soil waste vent or anti syphonage pipes as per as per IS - 14735 of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining (Nos.)

For 110mm o/d pipes Bend Plain

For 110mm o/d pipes Collar

For 90 mm o/d pipes bend plain

For 90 mm o/d pipes Collar

With90 mm i/d outlet deep seal at ground floor

Providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition. Size 75 mm x 75 mm

G.I. Pipe 15 mm i/d to 25 mm i/d

Providing and fixing in position automatic brass Ball Cock in tanks.

iii) Brass Ball Cock with rod and Plastic Ball.25 mm i/d

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank - Double Layer Tanks

a) 1000 Litres capacity

c) 500 Litres capacity

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.

c) G.I. tank nipple 25 mm i/d

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150 mm x 150 mm , cover and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm and chamber including cost of all bricks work in cement mortar 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50 mm.

(a)100 mm internal Diameter S.W. Gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm (Nos.)

Providing and fixing in position vitreous Chinaware white channel of approved make (to the approval of Engineer-in-charge) of size 600 mm x 100 mm including laying and fixing in cement concrete 1:2:4 complete in all respect.

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES:

i) b) Wiring fan point with sheet metal fan box (shape hexagonal & sheet thickness not less than 1.60 mm) in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade with step type electronic fan regulator 100watts.

ii) Wiring light point in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade.

iv) Wiring 3 pin 6 Amp. wall socket (Shuttered) point in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade complete with bonding to existing earth with PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1 sq. mm, 1100volts grade.

v) Wiring 3 Pin 6 Amp. Plug control comprising wall socket (shuttered) and switch including bonding to existing earth with PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1 sq. mm, 1100volts grade complete.

vi) Wiring 3 pin 16/20 amp. power plug control (shuttered) and switch.

iii) Wiring call-bell point in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade with bell push and electronic buzzer 230 volts AC (including the cost of bell push, electronic buzzer & powder coated concealed metal box for electronic buzzer).

PVC INSULATED SINGLE CORE FRLS COPPER CONDUCTOR CABLE:

ii) PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq.mm, 1100volts grade

iii) PVC insulated copper conductor single core FRLS cable (ISI marked) overall 2.5 sq.mm, 1100volts grade

iv) PVC insulated copper conductor single core FRLS cable (ISI marked) overall 4 sq.mm, 1100volts grade

vi) PVC insulated copper conductor single core FRLS cable (ISI marked) overall 10 sq.mm, 1100volts grade

XLPE/ PVC INSULATED UN-ARMOURED CABLES (LOOSE IN THE EXISTING TRENCH OR PIPE): Supply and laying of XLPE/ P.V.C. insulated P.V.C. sheathed aluminium conductor un-armoured cable working voltage upto and including 1100 volts grade to be laid loose in the existing trench or pipe as per PWD General Specifications 2010:- Make:- Polycab, Havells, KEI,

xxii) XLPE/ PVC insulated PVC sheathed aluminium conductor unarmoured cable working voltage 1100volts grade 25sq.mm (3 ½ Core)

HEAVY GUAGE WELDED CONDUIT PIPES: Supply and erection of 20mm dia. heavy gauge welded conduit pipe (1.60mm thick) suspension rod for ceiling fan complete in all respect as desired by the Engineer-incharge.

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC pipes & HDPE pipes (fire retardant) for wiring purposes including bends, inspection boxes etc., where necessary including other petty material as per PWD General Specifications 2010:- Make:- Diplast/Canon/ AKG/ Poly India/ Polycab/ Ravindra/ Supreme

vi) Heavy gauge PVC conduit pipe 20mm dia. (ISI marked 2 mm thick) Flushed

vii) Heavy gauge PVC conduit pipe 25mm dia. (ISI marked 2 mm thick) Flushed

ix) Heavy gauge PVC conduit pipe 40mm dia. (ISI marked 2 mm thick) Flushed

(xix)(d) Supply and erection of PVC flexible pipe complete with compression glands, having locking arrangement, check-nuts as required :-

GALVANIZED IRON PIPES AND G.I. EARTHING : Earthing of Sheet metal/ iron clad switches and metallic cases etc., with 8 SWG (4mm dia.) electrolytic copper wire thimbled (with 1 nos. copper thimble) to 30 cm x 60 cm x 3 mm thick tinned copper plate (made cylindrical) burried 10 metre below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) on wall and in floor etc., up to 13 metre in length (including bore length). G.I. pipe 20mm dia. (A-class) should be laid in the hole of excavation from bore surface level to 1 feet below ground level and having wire mesh funnel fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm around the hole of excavation.

Supply and Erection of 8 SWG 4mm dia copper wire run through 20mm dia. Heavy guage welded conduit pipe (As additional length).

SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets, power switch and sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including connections and petty material etc.

xxii) Bakelite batten holder large size

MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: Supply and erection of Miniature Circuit Breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles/lugs. GROUP-A: (Siemens (Beta Guard), Legrand (Lexic) & Schneider (Neo Break), L&T (Exora,Hager)

ii) Miniature circuit breaker single pole 6 to 32amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply

xiv) Miniature circuit breaker four pole 6 to 32amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's: Supply and erection of sheet metal double door distribution boards of suitable size and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles and bonding to existing earth etc.

ii) Sheet metal double door T.P. & N. distribution board (dust protected) provided with bus bar, neutral link and din bar, suitable for incorporating FP/ TPN MCB's/ isolators for incoming and DP/ SP & N/ Single Pole MCB's/ RCBO/RCCB's for outgoing 8 way each

SWITCH DISCONNECTOR FUSE UNIT (With Sheet Enclosure):

i) 32Amp. 415volts three pole & neutral switch disconnector fuse unit with HRC Fuses in sheet enclosure

GI PIPE POLE BRACKETS: SINGLE ARM BRACKETS: Supply and erection of G.I. pipe 40mm dia. (A-class) single arm bracket atleast 1 metre long arm to give a total overhang at a tentative angle of 100/105º, the bracket should be fixed on the top of the GI pipe pole having top outer dia. 80mm with GI reducer 80mm x 40mm with two coats of an approved aluminium paint complete in all respect as approved by the Engineer-in-charge at site.

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of double walled corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation (making necessary trench), placing the pipe in position and back filling with excavated soil etc. of the required size. Make : Duraline / Emtel

ii) Double walled corrugated (DWC) HDPE pipe 63/ 51mm (outer/ inner dia.)

Earth filling with good quality earth obtained from outside the plinth including compensation of earth, loading, unloading, carriage from outside the premises to site of work, spreading, laying watering compacting with rammer complete as per specifications. (Cum)

Providing and fixing 16 gauge stainless steel pipe of various sizes railing of grade 304 duly fixed on ramp with the help of bolts grouted on floor with hand rail and newel post of 50 mm dia stainless steel pipe, balusters of 40 mm dia stainless steel pipe complete in all respect as per specification and entire satisfaction of Engineer-in-Charge. (Railing on Entrance Ramp Design as per guidelines issued for persons with disability) (Rmt.)

Construction of Platform for placing PVC Water Storage Tank with Brick Ballast Work, Plaster, CC 1:8:16, CC 1:2:4, cement rendering etc. of required size complete in all respect.

Supply & installation of self contained drinking water cooler with (Non CFC Refrigerant) energy efficient compressor of make USHA, Model No. SRA 60 120 G, cooling capacity Ltrs/hr. 60, storage type capacity 120 Ltrs. Including installation etc. Complete in all respect as approved and desired by the Engineer-in-charge at site. Make USHA/Voltas or its equivalent.

Supply & installation of AQUA FLO DX UV Water purification system, capacity 60 'tr. Per hour, 100% chemical free, Dimension 210mm width x 140 mm depth x 382 mm height, in built voltage stabilizer, Hi Flo, Dual Cartridge including installation etc. Complete in all respect as approved and desired by the Engineer-in-charge at site. Make EUREKA FORBES or its equivalent.

Supply and erection of High quality aluminium extruded with decorative end caps glazed LED batten of Make Jaguar Item Code LGLZ01x020XC or Its equilant Make and Cat. of Philips / Wipro including erection of the same with connections, testing etc.complete in all respects as approved and desired by the Engineer in-charge at site.

S/E of Energy Saving Fan Ceiling Fans 1200 mm sweep ( 48" ) having two ball bearing but without regulator including flexible wire & petty material etc. for connections complete with erection, connections and testing etc. complete in all respect as approved and desired by the Engineer-in-charge at site. Make :- Crompton Entrust 50-5 Star or its equillant make Havells ES-50 Premium 5 Star /Orient.

Supply and erection of 12" Heavy Duty Exhaust fan (HDEF) (300mm-900RPM) Single Phase of make Crompton Model EXHD 300-6-1 or Its equialant Make Havell's Turbo Force SP / GE 151 marked heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and louver shutter complete in all respectsas appd. and desired by the Engineer in-charge at

Supply and erection of Plastic Ventialtion Fan Ventilus 10" (250 mm - 900 RPM) single Phase of make Crompton , White Colour or Its equialant Make Havell's / GE including erection, connections and testing etc. complete with flexible wire and petty material regd. for connections and louver shutter complete in all respects as approved and desired by the Engineer in-charge at site

Supply and erection of Wall fan of 400mm sweep (16") High Speed. Make Crompton WM Fizzair Opel White or Its equilant make Havell's / Orient ISI marked heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and Aluminium louver shutter complete in all respects as appd. and desired by the Engineer in-charge at site.

Supply and erection of Glazed LED Batten Hgh Qualty Aluminium Extruded with decorative end caps of Make Jaguar Item Code LGLZ01X0410XC or Its equilant Make and Cat. of Philips / Wipro including erection of the same with connections, testing etc.complete in all respects as approved and desired by the Engineer In-charge at site.

Supply & erection of Computer Terminal suitable for Computer Networking with modular accessories one on. metal box 12 module 8" x 6", 3 Nos. Switch 6 Amp, 3 Nos. Socket 3 pin 16 Amp, 1 No. Switch 20 Amp, 1 Nos. Socket 20 Amp and 1 No. Modular Accessories including connections & testing complete in all respect as desired by the Engineer-In-Charge at site.

Supply & Erection of LED Street Light 45w in aluminium pressure Die Cast housing with touched glass cover (IP 66 protection ) of Make Jaguar Item Code LSR T 0150 4SxC or its equilant make and Cat Philips / Wipro / Halonix including erection of the same with the existing bracket fixed with pole, connections and testing etc. complete in all respects as aproved by the Engineer in charge at site.