Construction of 10 Class room, 1 Boys and 1 Girls Toilet in Government Higher Secondary School at Moolaikaraipatti in Tirunelveli District

Amount

Earth work excavation for foundation in all soils and sub soil and to full depth as may be directed except in hard rock requiring blasting but including shoring, strutting and balling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of not more than 15cm thick well rammed consolidated and depositing the surplus earth within the compound with an initial lead of 10 metres and lift of 2 metres in places shown by the departmental officers clearing, leveling the site etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling in foundation, basement, etc with Stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, with Conveyed earth of 5KMMR in Layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling with Sand in layers of not more than 15 cm thick without consolidation etc. complete complying with standard specification and as directed by the departmental officers.

Brick work in following Cement Mortar1:6 ( one Cement and Six crushed stone Sand (M Sand) )using best quality of Country bricks 8-3/4" x 4-1/4" x 2-3/4" foundation and basement including curing, etc., complete complying with standard specification.

In Ground Floor

In First Floor

In Second Floor

Brick work in following Cement Mortar1:5 ( one Cement and Five crushed stone Sand (M Sand))using best quality of Country bricks 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specification.

In Foundation & Basement

In Ground Floor

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/ms and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg. of sand,

but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

In Foundation & Basement

In Ground Floor

In First Floor

In Second Floor

Plain Cement Concrete 1:2:4 (One Cement, Two crushed stone sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for wearing Coat including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Providing Anti-termite treatment to soil adjacent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Stage 1: Spraying Anti termite treatment chemical solution for the foundation before laying the foundation concrete at bottom and sides of the foundation.

Stage 2: Spraying Anti termite treatment chemical solution to the grade beam level, spraying has to be done for the grade beam, brick masonry in the super structure in contact with back fill earth.

Stage 3: Spraying Anti termite treatment chemical solution on sand for the flooring before laying the flooring concrete; the treatment has to be carried out on the sand filling in basement and after leveling operation is over.

Stage 4: Spraying Anti termite treatment chemical solution around the building on outside by making crow bar holes at an interval of 15 cms to a depth of 30 cms before laying the plinth projection. These holes have to be closed after the treatment.

Brick partition walls using best quality of Country bricks 8 3/4" x4 1/4" x2 3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand (M Sand)) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

In First Floor

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand (M Sand) and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three crushed stone sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

In First floor

Weathering course concrete using best quality broken brick jelly of size 20 mm uniform gauge in pure slaked lime in the proportion of brick jelly to lime being 32 to 12 1/2 by volume and laid over the RCC roof slab in a single layer and consolidated to the finished thickness by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling jaggery and lime water etc. complete complying with standard specification.

Finishing the top of roof with one course of approved first quality machine pressed tiles of size 230 mm x 230 mm x 20 mm thick of approved quality laid in cement mortar 1:3 (one cement and three crushed stone sand)(M Sand) 12mm thick mixed with water proofing compound confirming to Indian standard specification as approved by the departmental officers at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same mortar mixed with the water proofing compound and red oxide etc. complete complying with standard specification.

Cement concrete 1:5:10 (one cement, five crushed stone sand (M Sand) and ten hard broken granite stone jelly) using 40 mm gauge hard broken granite stone jelly for flooring including consolidating rendering the top surface rough to recive the floor finish and curing etc., complete complying with standard specification.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supplying and fixing in position both sides polished new cuddapah slab of 20/30mm thickness for cup-board shelf, urinal partition etc. including cost of slab, transportation charges in work site labour charges for forming grooves in masonry if necessary fixiing the slab in position with CM 1:3 ( One cement and three crrused stone sand (M Sand) ) curing as directed by the departmental officers etc., complete.,

Manufacturing, supplying and fixing of steel doors with following specification. MS Angle of size 40x40x6mm at 3.5 Kg/m used for outer frame and MS Angle of size 35 x 35 x 5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided at required intervals in the Shutter frame and welded intact on both ends to the shutter frame. 18GCR Sheets of best quality is laid as panel in the shutter frames.18x5mm at 0.70 Kg/m MS Flat is welded over the 32x6mm @ 1.50 Kg/m MS Flat on the rear side of the door, sand witching the CR sheet for rigidity.

Additional stiffeners with 18x5mm at 0.7 Kg/m MS Flats are provided diagonally on the rear side of the shutter. 3 Nos. of hinges in case of single leaf and 6 Nos. of hinges in case of double leaf shutters is provided. 6 Nos. of hold fasts 200mm length spliced at the ends are welded to the outer frame of the door. Tower bolt 2 Nos., one at the top and the other at bottom are provided. One aldrop is provided in case of double leaf door at lock rail section in the door. In single leaf doors, one more aldrop is provided in the inner side of the lock rail section

of the door, one rotating locking arrangementslocking arrangements for inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place in case of a double leaf door. MS Flat 32x3mm at 1.10 Kg/m is provided on the edge of the one shutter to conceal the gap between the two shutters. A tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete.

Single Leaf 1.00 m x2.10 m (Fully sheeted)

DoubleLeaf 1.20 m x2.10 m (Fully sheeted)

Manufacturing, supplying and fixing of steel entrance doors with fixed Portion at sides of Size 3.6 mx 2.9 m (1.80 X 2.10 m - Door & 1.80X2.10 m - Fixed at side, 0.80 x 3.60 m M.S grill at top) With the following specification M.S angles of a size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32x6mm M.S. flat is provided at required intervals in the shutter frames 18 gauge C.R. sheet is laid as panel and welded intact for 1/3 bottom portion of the shutter and side fixed Portion. M.S. flat 18x5mm is welded over the 32x6mm M.S. flat sand witching the CR sheet in between additional stiffener with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. The balance 2/3 portion at top 0.8m is provided with grill at an average weight of 20kg/m2 for Shutter

fixed Portion 3nos. of hinges in case of single leaf and 6 Nos in case of double leaves shutter to be provided 6nos of holdfasts 120mm in length made of angle section spliced at the ends are welded to the outer frame of the door. Tower bolts 2nos. one at top and the other at the bottom arte provided one aldrop is provided at on appropriate place in the door.One aldrop is provided in the inner lock rail section in the door.

and one more aldrop is provided inthe inner rail section of the door one rotating locking arrangements locking arrangements for inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place in case of a double leaf door. M.S Flat 32x3mm at1.1 Kg/m is provided on one Shutter to conceal gap between the two Shutters. A Tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation of fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of materials, labour transportation to side of works, loading, unloading and all other incidental charges etc., complete

Double leaves

Fabricating, supplying and fixing of steel Emergency exitdoor cum emergency window with the following specification. M.S. angle of size 40x40x6mm are used for the outer frames and M.S. angle of size 35x35x5mm for the shutter frame, stiffners with 32x6mm M.S. flats provided at required intervals in the shutter frames 18 guage CR sheet is laid as panel and welded instant for 1/3 bottom portion of the shutter, M.S. flat 18x5mm is welded over the 32x6mm M.S flat sandwitching the CR sheet in between additional stiffner with 18x5mm M.S. flat is provided diagonally at the rear-side of the shutter. The balance 2/3 portion at top is provided with grill at an average weight of 15kg/m2 and the top portion of operation emergency window is to be made of 25x25x3mm M.S. angle welded intact with CR sheet and 25x3mm M.S. flat at diagonally at the near side of the window at required intervals 6 Nos. of hinges to be provided,6 Nos of holdfast 100mm in length made of angle section spliced at the ends are welded to the outer frame of the door.

Tower bolts 2 Nos. one at top and the other at the bottom are to be provided one aldrop is provided at an appropriate place in the door 2 Nos. of 'D' type handle for emergency window and 2 Nos of handle for door is to be provided at appropriate places. A tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation of fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of materials, labour transportation to side of works, loading, unloading and all other incidental charges etc., complete.

Double leaves

Manufacturing, supplying and fixing in position of Steel Sheeted windows with the following specifications. Outer frames of windows made of ‘Z’ section F7D of size 33 x 25 x 3mm at 1.419 Kg/m and mullion ‘J’ Section (F4B) of size 46 x 25 x 3mm at 2.28 Kg/m and shutter section of made of F7D of 33 x 25 x 3 mm at 1.419 Kg/m as specified in IS 7452 / 1990.Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18 x 5mm MS Flat at 0.70 Kg/m at 3 Nos. for each shutter and additional diagonal stiffeners of the same MS Flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in positional firmly.2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18 x 5mm MS Flats are revetted to the shutters at an appropriate height in window. Suitable opening is left for its easy operation.

A stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle.Each window shutter having an adjustable stay made out of 18 x 5mm at 0.70 Kg/m MS Flat of length 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using MS Flat of 18 x 5 mm at 0.70 Kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter.An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge to edge between them.

All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers. All sections should be in confirmed with IS 7452 / 1990. The cost includes cost of all materials, labour charges and other incidental charges, etc., complete.

Three Leaves

Supplying and fixing Solid panel PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter.( Solid panel PVC door shutters with frame)

Supplying and fixing PVC sliding door with Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames, 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter including slidng arrangements.

Supplying and fixing mild steel iron grill for windows ventilators and grill gate etc., including one coat of red oxide primer using M.S angle of size 40 x 40 x 6 mm and grill using 20 x 6mm M.S flat and necessary hold fast with M.S angle of size 40 x 40 x 6 mm - 230 mm long spliced at end is to be provided at appropriate places for fixing the grill etc., complete complying with standard specification. The type design for the grills should be got approved by the departmental officers before execution.

Supplying and fixing in position steel balustrade using 20mm size square bars at 15cm centre to centre and two balusters in single step centrally located and top shall be welded to 40mmx6mm mild steel flat to fix the handrail and bottom fixed in the step concrete M.S. Flats of size 50mmx6mm to be provided at the centre of the balustrade connecting all the square bars to the entire length of the balustrade and the square bars well anchord in the floor / step concrete through fish tail splay at bottom including painting the steel member of the balustrade with one coat of red oxide primer etc., complete complying with standard specifications.

Supplying and fabricating and fixing of 40mm G.I. Pipe of‘B’ class for Hand Rails including cutting the pipe to the required length and shape grinding the edge smooth welding wherever necessary as directed by the departmental officers including cost of one coat of red oxide primer as directed by the departmental officers etc. complete complying with standard specifications. The rate includes cost of G.I.Pipe, taxes and labour charges for fixing in position.

Supplying and fixing GI pipe handrails for Differently Abled persons using 50mm dia GI pipe double handrail at a height of 800mm and 900mm from floor level with 25mm thick MS square rods as balusters embedded in the concrete and welded with pipe at 60cm centre to centre as shown in CA Job No. 9123 / 1 including cutting, welding, bending and fixing charges and applying one coat of red oxide primer for MS members as directed by the departmental officers

Providing Blackboard in two layers with first layer in cement mortar 1:5 (one cement and five crushed stone sand (M Sand) )20mm thick and the second layer in Combination mortar 1:1:6(one cement one lime and six crushed stone sand) 20mm thick and 50mm width including cost of one coat of block oxide paint of approved quality etc., complete complying with standard specification and as directed by departmental officers.

Supplying and fixing of RCC well ring of following thickness of size 1.2x0.075x0.30m in RCC 1:2:4 using 20mm HBGS jelly including cost of Reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18/20mm above with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand (M Sand) ) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc Complete as Per Standard Specification., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Flooring with Anti skid self designed colour ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Crused stone Sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing with printed design colour ceramic tiles of size 300 x 450 x 8mm with best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand (M Sand)) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with cement based hydraulically pressed anti skid tiles (pattern design) of 20 mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Manufacturing, supplying and fixing in positon of RCC Jally of 5cm thick in cement concrete 1:2:4 using 20mm machine crushed stone jelly (excluding cost of reinforcement steel) including cost of mould, finishing, curing, lifting, fixing in position etc., complete complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick mixed with bonding agent cebex 112, zydex-zycrete 2X or other equivalent compound confirming to BIS at 200ml of 1 cement bag 50kg for increased workability and air entraintment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick mixed with bonding agent cebex 112, zydex-zycrete 2X or other equivalent compound confirming to BIS at 200ml of 1 cement bag 50kg for increased workability and air entraintment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering sand) 20mm thick mixed with water proofing compound to BIS at 2% by weight of cement used and bonding agent cebex 112, zydex - zycrete 2X or equivalent compound conforming to BIS at 200ml of 1 cement bag 50 kg for increased workability and air entraintment used finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)cutive Engineer before use on works.)

Supplying & Fixing of Incinerator for ladies bath room etc. complete complying with standard specification.

Supplying, laying and jointing CPVC pipes (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with higher pipe thickness) Standard Dimension Ratio- 11)of approved qualityand best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs,CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Above Ground Level(External)

25mm CPVC Pipe

20mm CPVC Pipe

Supplying, laying and jointing CPVC pipes(chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using SOLVENT OF 118 ML (but excluding cost of such specials) and fixing making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. Below ground level (External)

32mm dia. C.P.V.C. Pipe

Supplying and fixing in position the following CPVC specials of best approved quality and heavy type and good variety excluding fixing charges, but including cost of cutting and threading etc complete for jointing the CPVC specials etc., complete complying with standard specification. (The CPVC specials should be got approved by the Executive Engineer before use on works)

CPVC Union

25 mm dia CPVC union

20 mm dia CPVC union

CPVC Elbow

25 mm dia Elbow

20 mm dia Elbow

CPVC Tee

25 mm dia CPVC Tee

20 mm dia CPVC Tee

CPVC Hex Nipple

25mm Dia Hex Nipple

20mm Dia Hex Nipple

CPVC Reducer

20X15mm CPVC Reducer

CPVC Reducer Tee

25 mm x20mm CPVC Reducer Tee

20mm x15mmdia CPVC ReducerTee

CPVC Reducer Elbow

25 mm x20mm CPVC Reducer Elbow

20mm x15mmdia CPVC Reducer Elbow

Supplying and fixing in position best approved of best quality PVC soil/waste pipes for various Dia having 6Kg/Sq.cm pressure BIS mark and providing leak proof joint using PVC adhesive including fixing to the wall with special PVC /MS clamp , T.W plugs , brass screws , etc and making connection to all sanitary fitting, dismantling masonry /RCC works wherever found necessary and making the good dismantled portion to the original condition,including testing for any leakages, etc, complete complying with standard specification.( The PVC pipe should be got approved by the Executive Engineer before use on works) The rate for earthwork excavation, sand filling and refilling charges etc., will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

110mm dia pvc pipe below ground level

110mm dia pvc pipe above ground level

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC Elbow

110mm dia pvc Bend

Supplying and fixing in position best approved and heavy tytpe quality of Gun Metal Gate Valve / Wheel Valve with ISI mark of the following sizes including cost of shellac, thread ball, including labour charges for cutting and threading of GI pipes as directed by the departmental officers etc., complete complying with standard specification for both internal and external water supply arrangements. (The gate valve/ wheel valve should be got approved by the departmental officers before use on works.)

25 mm dia Gun Metal Wheel Valve

20 mm dia Gun Metal Wheel Valve

Supplying and fixing in position 15mm dia. brass C. P. screw down tap ( Heavy duty ) of best approved make and quality including cutting, threading. G. I. Pipes wherever necessary and fixing to the galvanized iron pipes in position etc., complete complying with standard specification ( Screw down tap to be used on works should be got approved from the Executive Engineer before use).

Supplying and fixing in position of P.V.C water storage tank of best approved quality and brand of super thick with the capacity of 1000 Litres with accessories including giving necessory connections etc., complete as directed by the departmental officers. ( The P.V.C. water storage tank should be got approved by the Executiove Engineer before use on works.)

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crused stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers a)50mm thick using 20mm HGB Jelly

Supplying& fixing in Position Urinal Partition With White Adanga Marble Slab 18mm to20mm thick of4'00"x2'00" size and above of best quality including Dismantling Masonry , if necessary and re doing the same to original condition etc, complete,complying with std Specification(The marble Slab should be got approved by Executive Engineer before use on works)

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings.....

such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works) White glazed EWC 10 Lit Capacity PVC flushing tank fixed on wall without CI brackets

Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin With out Pedestal of size 550 x 400mm with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing position PVC Nahani Trap of 100mmx75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three crushed stone sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position Indian make white glazed earthenware squating type urinal of best quality and approved make including dismantling masonry, if necessary and re-doing the same to original condition, etc., complete complying with standard specification. (The squatting urinal should be got approved by the Executive Engineer before use on works).

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and filling 40mm ISS metal in dispersion trench including stacking for pre measurements around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc.,complete.-

Supplying and filling 20 mm ISS metal in dispersion trench including stacking for pre measurements around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc.,complete.

Supplying and Installation of Ceramic steel chalk writing board with the following specification. GI sheet of 2mm thickness is fixed with the wall side over the GI sheet necessary special adhesive is spreaded and 9mm MDF Board is fixed on this GI sheet 0.40mm thick ceramic chalk board is provided over the MDF board and the whole arrangements are fixed to the frame using heavy anodised aluminium section and chrominium plated provided in the corners. The whole arrrangements are fixed to the wall using wooden Plugs, screws, etc. complete complying with standard specification

P.Arun

SABARI DHARAN ENGINEERING CONTRACTOR