ADDITIONAL/ALTERATION TO OMQs OF HQ WAC SUBROTO PARK (PHASE-II)

Amount

B & R WORKS

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc. 1.5 Sqm but n exc 4.0 sqm including making good of jambs of opening with rendering in cement mortar 1:4, complete all as specified and direcetd.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exc. 1.5 Sqm including making good of jambs of opening with rendering in cement mortar 1:4, complete all as specified and direcetd.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each and refixinf in same opeining, complete all as specified and direcetd.

M&L for chipping of spalled and loose concrete of soffits of slabs,chajjas, stair case, facias, parapets, columns, beams and like as directed, roughening and cleaning concrete surafce with steel wire brushes, removing of rust from existing steel surface with rust remover of SIKKA rustoff 100 applied in two coats @ 0.15 Kg/Sqm per coat of steel surafce and cleaning all rust with wire brushes cleaning with water and allowed to dry including S&F welded fabric GI wire mesh or wire size not less than 75mmx75mm and 3.0mm dia as reinforcement to concrete after placing the additional reinforcement all concrete surface shall thoroughly scrubbed with brushes, washed with water and allowed to dry this surface apply chemical polycrete admixture at the rate not less than of 2% by weight of cement and providing minimum 30mm thick (average thickness) gunniting mix (using 1 part of Ordinary Portland Cement and 2 parts of Ghaggar sand mixed with adhesive/admixture at the rate as directed) with a pressure 2.00 to 2.5 kg/sqcm by guniting machine and making the surface even including 5mm thick plastering in CM 1:3 on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement including necessary form work to be carried out complete all as specified and directed. Note.- Where ever reinforcement required will be measured and paid seperatly

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition) including removal of debris outside the MoD land, complete all as specified and directed.

M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded aggregate as in spiral staircases (including Landing) etc., complete all as specified and direcetd.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for TMT mild steel bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work not exc. 10cm wide for fair finished surfaces of concrete, complete all as specified & directed

Demolition of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer), laid, bedded and pointed in any mortar, complete as specified and directed.

Demolition of Mud in roofs, any thickness, including removal of debris outside of MoD land and cleaning of surface to received padding, complete as specified and directed.

M&L for PCC M-15, nominal mix, type B-0(1:2:4), using 12.5mm graded crushed stone aggregate as in PCC padding on roof etc., and the like rounded or chamfered on edges including necessary form work, complete as specified and directed.

S&F Pressed steel frames of size 105mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, PCC 1:3:6 with 12.5mm graded stone aggregate for filling of hollow portion, complete as specified and directed.

S&F Pressed steel frames of size 165mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, PCC 1:3:6 with 12.5mm graded stone aggregate for filling of hollow portion, complete as specified and directed.

S&F 35mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both the faces complete all as specified and directed.

S&F 35mm thick 2nd class hardwood factory made glazed and skelton shutters open rebated and prepare to receive glass, guage, etc. (without sash bars), edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass/guage etc size of member etc; size members of shutters as specified in SSR part I Section-8 clauses 8.24(a); supplied and fitted to chowkhat including galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed.

M&L for prepration of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L for preparation of old painted surfaces, of wood/steel/concrete of any description over 10cm width or girth by cleaning, sand papering, brushing etc, filling in crevices and cracks etc with approved filler and applying one coat of synthetic enamel paint, complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet, edges will be painted to match with prelam sheet, reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete as specified and directed.

S&F factory made Solid PVC Moulded Door Shutter with wood free EPS core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on the back face with particle board core, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified and directed.

S&F extruded aluminium alloy handle, fabricated type, anodised, 150mm long (ISI marked), complete as specified and directed.

S&F butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete as specified and directed.

S&F aluminium alloy, 300mm long anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, complete all as specified.

S&F floor door stopper of stainless steel body two legged and tongue with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm, complete all as specifed and direcetd.

S&F aluminium door cill strip 38mm wide fixed with screw/nails, complete all as specified and directed.

S&F mild steel 300mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel, complete as specified and directed.

Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement as on wall complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement as on wall complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces of ceiling, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for prepration of new plastered or unplastered surfaces of wall and applying two coats of oil bound distemper, complete all as specified and directed.

M&L for preparation of old decorated surfaces plastered or unplastered on walls including cornices pilasters by brooming down or steel wire brushing and efforescent salts and applying two coats of oil bound distemper, complete all as specified and directed.

M&L for preparation of old decorated surfaces plastered or unplastered on ceiling including cornices pilasters by brooming down or steel wire brushing and efforescent salts and applying two coats of oil bound distemper, complete all as specified and directed.

M&L for prepration of new plastered or unplastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of plastered or unplastered old decoraced surfaces on ceiling including cornices pilasters by brooming down or steel wire brushing, scraping down, smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash on ceiling complete, all as specified and directed.

M&L for prepration of new plastered or unplastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of plastered or unplastered old decoraced surfaces on wall including cornices pilasters by brooming down or steel wire brushing, scraping down,smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash on wall, complete all as specified and directed.

M&L for PCC M-15 (nominal mix), type B-1(1:2:4), using 20mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified & directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for glazed ceramic coloured printed tiles 7 to 8mm thick of size 300 x 450 mm as in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L for vetrified coloured tiles light shade(1st quality) of size 600mmx600mm of thickness not less than 9mm on vertical surface as in skirting or dado etc., set and jointed in neat cement slurry and pointed with colour cement, laid over and including 10mm thick bedding layer in cement mortar 1:4, complete all as specified & directed.

M&L for vetrified coloured tiles light shade(1st quality) of size 600mmx600mm of thickness not less than 9mm as in floors etc., set and jointed in neat cement slurry and pointed with colour cement, laid over and including 15mm thick bedding layer in cement mortar 1:6, complete all as specified & directed.

M&L for Joint free non-skid coloured printed ceramic tiles of size 600mmx600mm of thickness not less than 7 to 8mm as in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for Joint free non-skid coloured printed ceramic tiles of size 600mmx600mm of thickness not less than 7 to 8mm on vertical surface as in skirting or dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

M&L for Joint free non-skid coloured printed ceramic tiles of size 300mmx300mm of thickness not less than 7 to 8mm as in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L for machine cut polished kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 20mm thick screed bed in cement mortar 1:4, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed.

M&L for polished kota stone slab 18 -20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 10mm thick rendering in cement mortar 1:4, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations, complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-1, (20 mm graded stone aggregate) as in sub base/ levelling course of floors complete all as specified and directed.

S&F PVC (SWR) pipes, 110mm dia, single socketed, in any length with solvent cement joints, laid in trenches or in floors or fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center, complete all as specified & directed.

S&F PVC (SWR) pipes, 75mm dia, single socketed, in any length with solvent cement joints, laid in trenches or in floors or fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center, complete all as specified & directed.

Taking down rainwater pipes (any size), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified.

S&F 110mm bore PVC (SWR) bends any radius, complete all as specified.

S&F 75mm bore PVC (SWR) bends any radius, complete all as specified.

S&F 75mm bore PVC (SWR) junction (Single T) equal or unequal with access door, complete all as specified.

S&F 110mm bore PVC (SWR) junction (Single T) equal or unequal with access door, complete all as specified.

S&F PVC (SWR) vent cowl of size 110mm bore, complete all as specified.

Taking up or down GI tubing with all connections and fittings of 15mm bore including cleaning for refixing or removal to store, complete all as specified and as directed by Engineer-in-Charge

Taking up or down GI tubing with all connections and fittings of 20mm bore including cleaning for refixing or removal to store, complete all as specified and as directed by Engineer-in-Charge

S&F galvanized iron water tubing, ‘medium grade’ 15mm bore, with all fittings such as bend, tee, union etc., fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

S&F galvanized iron water tubing, ‘medium grade’ 20mm bore, with all fittings such as bend, tee, union etc., fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

S&F in repairs, Vitreous China wash down water closet pan (pedestal pattern), white with cast iron ‘P’ or ‘S’ trap, fixing with screws of suitable size, plastic seat cover, white closed pattern with flat bottom and cover, complete all as specified, making connections to trap and to flush pipe, fixing flushing cistern etc. and making good to floors, complete all as specified and directed.

S&F in repairs, Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of cement concrete, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified.

S&F in repairs Stop valves, 15mm bore, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc.,complete all as specifed.

S&F in repairs, PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified and directed.

S&F in repair wash hand basin, vitreous China, flat back 550x400mm size, white including CP waste coupling 32mm size, PVC waste pipe 32mm bore, pair of brackets of mild steel 35 x 35 x 6mm size, complete all as specified and directed. Make:Cera/Hindware/Parryware for WHB

S&F in repairs chromium plated shower rose 125mm square size with arm 15mm dia 195mm long with bend 45 degree with brass flange, complete all as specified and directed. Make: Jaquar / Marc/Kohler.

S&F in repairs, health faucet with double lock, one meter long brass chromium plated steel flexible hose pipe and wall hook complete all as specified and directed.

S&F in repair stainlees steel paper holder with fap recessed type, complete all as specified and directed. Model No AHS-1553 of Make Jaquar or equivalent Marc/Kohler

S&F in repair Stainless steel towel racks with lower hanger , complete all as specified and directed. Model No AKP-35781PS of Make Jaquar or equvelent Marc/Kohler

S&F in repair single lever basin mixer without popup waste system , Hot and Cold Facilites and 450 mm long braidaed hoses chromium plated complete all as specified and directed. Model No- DRC-37011B of make Jaquar or equivalent in Marc/Kohler.

S&F in repairs single lever wall mixer with mixer provision of hand shower but without hand shower chromium plated, complete all specified and direcetd. Model No- DRC-37119 of make Jaquar or equivalent in Marc/Kohler.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed. MAKE: Prayag/Polytuf/Pearl.

Demolition of stone or brick masonry built in cement mortar including all quoins, arches etc.but excluding ashlar facing, dressed stone work etc, including removal of debrish outside the MoD land, complete all as specified.

M&L for brick work with sub class "B" brick (old size), straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with sub class "B" brick (old size) straight or curved on plan any radius in half brick thick wall and built in cement mortar 1:4, complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-1 as in Kerb stone(factory made), window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match, complete all as specified and directed.

S&F in repair rotationally moulded polyethylene water storage tank 3 layer (cylindrical vertical with closed top) hoisted & fixed in position of capacity 500 ltrs, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, complete all as specified and as directed.

S&F rotationally moulded polyethylene water storage tank 3 layer (cylindrical vertical with closed top) hoisted & fixed in position of capacity 1000 ltrs, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, complete all as specified and as directed.

S&F in repairs, sink with drainage board made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915X460mm bowl size 410X330X160mm, complete all as specified and directed.

S&F 0.5mm thick stainless steel Plate rack Grade -304 of overall size 750mmx750mmx250mm of standard quality and shape, fixed in repair, complete all as specified and directed.

S & F sheet glass shelf assembly consiting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 400mm long with CP brass bracket, fixed in repair, complete all as specified and directed.

S&F in repairs PVC bathroom storeage cabinet of size 600x400mm with mirror on front door, fixed with screws or PVC gutties, complete all as specified and directed. Make : PRAYAG/Nilkamal/ Commander

S&F window /ventilator section of frame 70 x 50 mm fixed to wall or concrete surfaces with screwing 100 mm long made of galvanised steel powder coated and section of shutter 47 x 20 mm mullion section 72 x 50 mm (base steel as per 513 D quality galvanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauge and wire mesh ti the shutter double door shutter) with total coated grill/guard bars made of square bars 10 mm dia a 150 mm c/c horizontal spacing fixed in MS flat frame(12 x 6) fixed to window fame with screw including 4 mm thick sheet glass, 0.36 mm stainless steel wire cloth with 1.40 mm aparture necesary fitting and all builders hardware such as handle tower bolts & stay etc type -4000 series ref drg No - CEAF/STD -191/2014 Sheet 1/2 & 2/2, compete all as specified and directed.

S&F window /ventilator section of frame 46 x 52 mm fixed to wall or concrete surfaces with screwing 100 mm long made of galvanised steel powder coated and section of shutter 46 x 46 mm mullion section 46 x 70 mm (base steel as per 513 D quality galvanised as per IS 277 with zinc of 120 gms/sqm) glazed with total coated grill/guard bars made of square bars 10 mm dia a 150 mm c/c horizontal spacing fixed in MS flat frame(12 x 6) fixed to window fame with screw including 4 mm thick frosted glass, 0.36 mm stainless steel wire cloth with 1.40 mm aparture necesary fitting and all builders hardware such as handle tower bolts & stay etc type -3000 series ref drg No - CEAF/STD -191/2014 Sheet 1/2 & 2/2, compete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves of 20mm dia, with iron wheel head, screwed both ends for iron pipe, complete as specified and directed.

S&F in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe or brass ferrule for bore of pipe 20mm (Minimum weight 210 gms), complete as specified and directed.

M&L for cement concrete, 1:5:10, type E-2 using 40mm graded crushed stone aggregate as in foundations, filling, mass concrete and sub base, complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and fair without using extra cement but using water proofing compound as per manufacturer's instructions, complete all as specified and directed. Note :Water proofing compound shall be measured & paid seprately.

M&L for Polythene film, black, 50micron laid in floors or vertical surface etc, complete all as specified and directed.

Supply only integral water proofing compound (ISI marked), complete all as specified and directed.

M&L for galvanized iron spout pipe 32mm dia projecting atleast 20cm clear of wall ‘light grade’ for sunken portion including making holes in walls & making good disturbed surfaces, complete all as specified & directed.

S&F in repairs stop valves, 15mm bore, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specified and directed.

S&F in repairs bib tap long body, 15mm bore, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) un-reinforced including removal of debris outside the MoD land, complete all as specified.

M&L for 75mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar or cement lime mortar for door, window and other openings or enlarging existing openings converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m, complete all as specified and directed.

M&L for Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar 1:6, complete all as specified and directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces, complete all as specified and directed.

M&L for water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first course of 10mm thick rendering in cement mortar 1:4 on concrete surface using WPC @3% by weight of cement finished even and smooth without using extra cement, second course ie. surface shall be thoroughly wire brush, cleaned , washed, dried up properly and apply evenly a bitumen primer conforming to IS 3488@ 0.40Kg per sqm, 3rd course of roofing membrane APP modified Polymeric membrane 3.0 mm thick of 3.60 Kg/ sqm weight consisting of five layers prefabricated with centre core of 160gms/Sqm polyster non woven fabric mat sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film before and after laying membrane sealing all the over laps 75mm on length side and 100mm on width side of membranes by torching as per manufacturer’s instructions by authorised applicator only, At the junction of roof and parapet wall a grove of 20 x 20 mm shall be made at the height of 100 mm and membrane shall be inserted and sealed with bituminous mastic joints/overlap shall be sealed with hot bitumen 85/25, complete all as specified and directed.

M&L for prepration of newly or previously untrested APP membrane surfaces of any description over 10cm width or girth and applying two coats of aluminum paint, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:4:8, type D2, using 40mm graded crushed stone aggregate as in sub base, surface finished even and fair, complete all as specified and directed.

M&L for Second class hard wood timber frame wrought in scantling in repair to replace old and decayed timber (including piecing, scarfing etc. of old and new timber if required) and removing defective portions to MES store, complete all as specified and directed.

M&L for 18/19mm thick block boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame-work, complete all as specified and directed.

S&F 75mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F in repair 25mm dia stainless steel 304 grade curtain rod with stainless steel bracket and designer end knobs fixed with plugs & screws, complete all as specified and directed.

M&L for Post Construction ATT (Anti-Termite Treatment) along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified & directed.

M&L for Post Construction ATT (Anti-Termite Treatment) Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified & directed.

M&L for Post Construction ATT (Anti-Termite Treatment) at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same, complete all as specified & directed.

M&L for Welding in repairs exc 2.5cm but n exc 5cm in length, thickness of Metal to be welded n exc 6mm, complete all as specified and directed.

M&L for applying 1-2mm thick JK/Birla wall care putty to achieve smooth finish surface of wall, complete all as specified and directed.

M&L for applying 1-2mm thick JK/Birla wall care putty to achieve smooth finish surface of ceiling, complete all as specified and directed.

M&L for complete removal of existing treatment old plastered or unplaster surface and applying two coats of weather coat over a coat of primer, complete all as specified and directed.

M&L for preparing plastered or unplaster new surface and applying two coats of weather coat over a coat of primer, complete all as specified and directed.

Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed. Note: For measurement superficial area in elevation shall be measured.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. One side prelam and other side plain18mm thick Celuka PVC ply for kitchen cabinet shutter and also manufactuer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 18mm thick Celuka PVC Ply for Shelf/Partitions/Drawer and also manufacturer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 5mm thick PVC of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 5mm thick PVC sheet paneling for back side (wall side) and also manufacurer's test report and test certificate is mandotary with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F 100mm size Stainless steel handle complete all as specified and as directed.

M&L for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed.

S&F 38mm size Stainless Steel Piano hinges, complete all as directed.

M&L for Granite (of any type) tiles 20mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone as in steps, jambs, pillars, window cills, cooking plastforms etc including cutting & polishing, laid over and including 15mm screed layer in cement mortar 1:4, complete all as specified & directed.

Excavation in post holes (or similar holes) each not exc. 0.50 cum, in hard/dense soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc. 25cm, watering and removal of excavated materials to a distance n. exc. 50m and making good surfaces, complete all as specified & directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in depth in hard/dense of soil and getting out, complete all as specified and as directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified.

M&L for cement concrete, 1:3:6, type C-2 using 40mm graded crushed stone aggregate as in foundations, filling, mass concrete and sub base, complete all as specified and directed.

M&L for cement concrete, 1:4:8, type D-2 using 40mm graded crushed stone aggregate as in foundations, filling, mass concrete and sub base, complete all as specified and directed.

M&L for Rolled mild steel work in joist, channel, pipe, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary length i.e. within 20mm of the length indicated), conforming to Fe-290(Gde E-165), complete all as specified & directed.

M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe-410-W (Gde-E- 250) quality-A , complete all as specified and direcetd.

M&L for prepration of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified.

S&F galvanized chain link fencing 2.0mm dia 75mm aperture both way including line wires, straning bolts, binding wire etc., complete all as specified and directed.

Taking up or down GI tubing with all connections and fittings of 25mm bore including cleaning for refixing or removal to store, complete all as specified and as directed by Engineer-in-Charge

S&F galvanized iron water tubing, ‘medium grade’ 25mm bore, with all fittings such as bend, tee, union etc., fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

M&L for applying two coats evenly a tack coat of hot air blown bitumen of grade 85/25 @ 1.50 kg per sqm per coat (one coat over plaster and one coat on polythene film) including cleaning of surface over polythene film, complete all as specified and direcetd.

Dismantling wrought iron or mild steel or other steel work of any description, complete all as specified and directed.

Taking down aluminium sliding door & fixed glazing including all fitting, complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1(using 20mm graded stone aggregate) manhole/drain cover set in cement mortar 1:4, complete all as specified and directed.

S&F of 500mm long stainless steel telescopic drawer channel, complete all as specified and directed.

E & M WORKS

Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power)complete including fixture and fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DB’s, meter board any type all as specified and as directed.

M&L for point wiring for one light point controlled by one SP switch with single core PVC insulated unsheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through and including non metallic rigid PVC concealed conduit, medium grade, ISI marked not less than 20mm dia, concealed in wall, ceiling with GI saddles, GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm FRLS (Nominal area), complete all as specified. Note :- i) Modular metal flush boxes shall be measured and paid under respective item. ii) Cost for cutting, chasing and making good to existing surfaces shall deemed to be included in the quoted rate.

All as per Srl item No. 3.02 here-in-before but for one ceiling fan/exhaust fan and wall mounted fan point controlled by one SP switch, complete all as specified and directed.

All as per Srl item No 3.02 here-in-before but for 3 pin 5 Amps socket out let on independent board and different wall controlled by one switch complete all as specified and directed.

All as per Srl item No. 3.02 here-in-before but for one 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and directed.

All as per Srl item No 3.02 here-in-before but for one light point controlled by Two, two way switch, complete all as specified and directed.

All as per Srl item No 3.02 here-in-before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent with cable size 1.5 Sq mm PVC insulated stranded sheathed copper conductor cable, complete all as specified and directed.

All as per Srl item No 3.02 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor FRLS cable PVC insulated including earth wire 2.5 Sq mm copper conductor FRLS cable connected to earth dolly complete, all as specified and directed. Note for Srl Item No 3.02 to 3.08 Make of cable: Havells/Polycab/HPL. Make of conduit: Havells/Plaza/Kalinga.

S&F TV co-axial socket, complete all as specified and directed by Engineer-in-charge. Make- Crabtee Cat Pt No. ACTKTLW000 or its equivalent legrand/Anchor.

S&F Telephone socket RJ- 111 Gang with shutter complete all as specified and directed by Engineer-in-charge. Make- Crabtee Cat Pt No. ACTKRWW-111 or its equivalent legrand/Anchor.

S&F modular switch one way 6 Amps one module complete all as specified and directed by Engr-in-Charge. Make:- Crabtree or equivalent model in legrand/Anchor

S&F modular socketes out let 6 Amps 5 pin complete all as specified and directed by Engineer-in-charge. Make:- Crabtree or equivalent model in legrand/Anchor

S&F modular switches 16 Amps single pole one way complete all as specified and directed by Engineer-in-charge. Make Crabtree/legrand/Anchor

S&F modular socket out let 16 Amps 3 pin combined shuttered complete all as specified and directed by Engineer-in-charge. Make:- Crabtree or equivalent model in legrand/Anchor

S&F modular step type electronic fan regulator 5 steps, 120 W-2 module suitable for 240 volt AC complete all as specified and directed by Engineer-in-charge. Make:- Crabtree or equivalent model in legrand/Anchor

S&F metal box 100x75x50 mm deep (nominal size) on surface all in recessed with suitable size of phonolic laminated sheet cover in front incluing painting etc as required in stair case for TV complete all as specified and directed by Engineer-in-charge.

S&F 4 pairs distribution boxes duly powder coated with KRONE connector terminal etc as required, complete all as specified and directed by Engineer-in-charge.

S&F modular white cover plate with frame 12 module, complete all as specified and directed by Engineer-in-charge.

S&F modular metal flush boxes 12 module, complete all as specified and directed by Engineer-in-charge.

S&F modular white cover plate with frame 8 module, complete all as specified and directed by Engineer-in-charge.

S&F modular metal flush boxes 8 module, complete all as specified and directed by Engineer-in-charge.

S&F modular white cover plate with frame 6 module, complete all as specified and directed by Engineer-in-charge.

S&F modular metal flush boxes 6 module, complete all as specified and directed by Engineer-in-charge.

S&F modular white cover plate with frame 4 module, complete all as specified and directed by Engineer-in-charge.

S&F modular metal flush boxes 4 module, complete all as specified and directed by Engineer-in-charge.

S&F modular white cover plate with frame 3 module, complete all as specified and directed by Engineer-in-charge.

S&F modular metal flush boxes 3 module, complete all as specified and directed by Engineer-in-charge.

S&F modular white cover plate with frame 2 module, complete all as specified and directed by Engineer-in-charge.

S&F modular metal flush boxes 1/2 module, complete all as specified and directed by Engineer-in-charge.

S&F modular bell push 6 Amp 1 module, complete all as specifed and directed by engineer-in-charge. Make:- Crabtree or equivalent model in legrand/Anchor

S&F modular switch 2 way 6 Amp, 1 module, complete all as specifed and directed by engineer-in-charge. Make:- Crabtree or equivalent model in legrand/Anchor

S&F of ceiling roses, surface bakelite 65x50mm 2 or 3 terminals , PVC/Polycarbonate, isolated body fixed on PVC round block, complete all as specified and directed.

S&F in replacement of ding dong bell AC 230 V single pole, complete all as specified and directed.

Taking down carefully copper/aluminium surface/conduit sub main wiring of size 2 Run of 4 sqmm cable and one Run of 2.5 sqmm cqable for earth wire from Main DB to sub DB and keeping in safe custody for giving credit and making good disturbed surfaces or walls , floors , etc complete all as specified and directed by Engineer-In-charge.

M&L for submain wiring with two single core 4.0 sq mm PVC insulated FRLS multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit of size not less than 25mm dia, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 4.0 Sqmm multistranded copper conductor cable as continuous earth wire complete all as sepcified and as directed. Make of copper cable - Havells/Polycab/L&T Note- (a) The two runs of single core cable and specified earth continuity conductor and PVC conduit with fitting acessories will be measured as one run. (b) Cost of cutting, chasing and make good to existing surfaces are deemed to be including in the quoted rate by the contractor.

Taking down unserviceable single pole and neutral enclosure with two pin and earth plug after disconnecting the electric supply, complete all as specified and directed by the Engineer-In- charge.

Taking down of TV and telephone socket and keeping in safe custody for giving credit, complete all as specified and directed.

Taking down any size PVC/Metalic conduit and keeping in safe custody for giving credit, complete all as specified and directed by the Engineer-In- charge.

S&F factory fabricated sheet steel enclosure, phosphatised, power painted, single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20 amp, 240 volts, 10KA, complete all as specified and directed.

S&F energy saving decorative box type batten light fitting 230 V surface mounted complete with high efficiency PMMA diffuser soft glare free light LED tube light 20 watts end cap with all accessories prewired, LED Rod 20 watts etcincluding flexible copper wire, three core cable PVC insulated sheathed, complete all as specified and directed. Make:- Crompton Cat Part No for fitting DMLN1T8-16 & for LED Rod LTT8-20 or equivalent in Havells/Bajaj/Polycab/ C&S

S&F energy saving decorative box type batten light fitting 230 V surface mounted complete with high efficiency PMMA diffuser soft glare free light LED tube light 10 watts end cap with all accessories prewired, LED Rod 10 watts etcincluding flexible copper wire, three core cable PVC insulated sheathed, complete all as specified and directed.

S&F in replacement of wall mounted LED light premium opal glass for reduced glare and integrated electronic driver nickel 10 watt LED fitting, 230 Volts, etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting and testing, complete all as specified and directed.

S&F ultra slim surface decorative 12 watt, 6000 K ,230 volt, LED LUNA ceiling fitting, complete with all accessories, connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing, complete all as specified and directed.

S&F in replacement of ENDURA RUGBY 10W LED IP 65 Bulkhead luminaries with opal diffuser 6000K , 230 Volts, etc complete with all accessories, connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting and testing, complete all as specified and directed.

Taking down including disconecting the electric connections of exhaust fans of any sweep including louvers and dismantling blades greasing and painting tthe whole assembly including marking MES No complete all as specified and directed.

Refixing only exhaust fan received from item No 3.45 above and connecting up including provision of suitable size of copper cable from connector of fans to ceiling rose complete all as specified and directed.

S&F of exhaust fan heavy duty plastic body 250 mm sweep with all accessories connecting up with twin core twisted flexible copper conductor cable from ceiling rose to exhaust fan including necessary fixing arrangement for proper fixing in wall complete all as specified and as directed.

Cutting of existing surface/wall for fixing of exhaust fan of required size including provn of grouting bolts and fixing with nuts & washers and making good the disturbed surface all as specified and as directed.

Taking down ceiling fan of any size/sweep and hanging the same back after servicing greasing and painting including connecting the wire to ceiling rose etc complete after completing the wiring all as specified and as directed.

Hanging only celing fan received from item No. 3.49 above and connecting up including provision of suitable size of copper cable from connector of fans to ceiling rose complete all as specified and directed.

S & F ceiling fan 1200 mm sweep 5 star rating 230 V single phase with all accessories complete with modular electronic type regular including prpvision of MS hooks suitable for hanging ceiling fans and connecting upto ceiling rose 1.5 Sqmm flexible copper wire complete all as specified and directed.

Taking down old unsv/MCB DB 12 way with MCB of any sizes and electronic meter of any size & capacity all as specified and directed.

Supply, installation, testing and commissioning of factory made Sheet Metal enclosure DB cum MCB box for incorporting 01 Nos trhree phase LT electronic meter , 01 Nos FP MCB Isolator (for incomming light circuit) and 20 Nos MCB SP on mounting separate rail for power and light. The front side of the meter box shall be provided with 01 Nos suitable size of glass for taking meter reading. The sheet metal enclosure shall be made out of 1.6 mm CRCA MS sheet powder coated, machine pressed weather proof spray painted on both side after proper primer coating with approved paint of red oxide primer as all sides, front openning type and necessary space for cable entering and locking arrangements. The enclosure shall be prewired with PVC insulator sheathed multi standard copper conductor FRLS cable IS-694, size of the cable 6.0 sqmm single core cable. The following accessories shall be supplied and fixed :- INCOMING (a) MCB FP isolator 63 Amp, 240 volt, 10 KA - 01 Nos. (b) Micro processor based, three phase, 3x 240 volt, 50 Hz, class 1.0, 4 wire, tamper proof design, LCD display multi fuctional electric energy meter in polycarbonate body, of capacity 10-60 amps, ISI marked, confirming to IS : 13779 with suitable ratio of CTs complete all as specified and directed - 01 Nos. OUT GOING (a) MCB SP 05 to 32 Amps 240V, 50Hz, 'C' Series - 20 Nos. Note :- Contractor shall submit the design of the sheet metal enclosure DB cum MCB box alongwith accessories for the approval GE before fabrication.

Supply and laying PVC conduit heavy duty not less then 20 mm dia concealed in wall for lay TV/Telephone socket including necessary fitting and cutting chessing etc, complete with making good of distrubed surface all as specified and directed by Engr-in-charge.

Supply and laying of single core PVC insulated but unseathed FRLS cable 1.5 Sqmm, 1100 Volts grade ISI marked with multi stranded copper conductor cable drawings through existing PVC conduit complete all as specified and directed by Engineer-in-charge. Note:-for invertor connection

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed.

Supply, laying, jointing and testing of 16 Sqmm 4 core XLPE insulated, screened, PVC bedded, galvanized steel wire or strip armoured electric power cable (heavy duty) with aluminium stranded conductor 1100 volts grade, laid in trenches, passing through ducts/pipes, fixing along poles, including taking out old unserviceable LT cable, complete all as specified and directed.

M&L for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable in trenches (total punned depth of sand shall be 18 cm after punning down) complete all as specified and directed. Note: punned thickness of sand shall be measured.

M&L for cover to underground cable with one layer of bricks using sub class ‘B’ bricks (Old size) laid flat across the cable complete all as specified.

Supply and laying galvanised steel tube light grade of size 50mm dia bore with all fittings laid in trenches or fix on wall for cable protection, complete all as specified and directed by Engr-in-Charge.

M/S MG GROUP

M/s Puja Construction Company

Hindustan Co.Co

Gaurav Construction Company

India Guniting Corporation

Adhunik Builders

Third Wave Services Pvt Ltd