Construction of Academic Building Phase-2, Girls Hostel and Boys Hostel at RLBCAU at Jhansi

Abstract of Cost - Civil/Plumbing, Fire/Electrical, LV/HVAC/Furniture Works

Location:- Jhansi, Uttar Pradesh

S.No. Description DSR Amount NDSR Amount

2 Furniture Works 0.00 9,05,67,255.00

4 Fire Fightimng Works 41,11,800.01 19,39,193.01

Sub Total (DSR + NDSR) 92,89,61,592.85

Sub Total of Project Cost 92,89,61,592.85

Digitally signed by ANUJ

PROJECT NAME:- CONSTRUCTION OF RANI LAKSHMIBAI CENTRAL AGRICULTURAL UNIVERSITY AT

JHANSI, UTTAR PRADESH.

MATRIX, SUMMARY

Sl. No. DSR-2023 DESCRIPTION DSR Amount MR Amount

A 2.0 EARTH WORKS 91,61,344.00 -

B 4.0 CONCRETE WORKS 44,07,222.00 -

C 5.0 REINFORCED CEMENT CONCRETE WORKS 19,31,56,592.00 -

E 8.0 MARBLE & GRANITE WORKS 86,45,642.00 11,14,82,326.00

L HORTICULTURE AND LAND SCAPING 4,58,616.00 -

M 21.0 ALUMINIUM & STRUCTURAL GLAZING 1,80,59,283.00 1,52,23,822.00

N 22.0 WATER PROOFING WORKS 64,63,996.00 -

Add: impact of Multiplying factor on

NonDSR of 0.973 as Analysis of NDSR 43,08,09,567.00 18,27,90,253.37

done on same patern of CPWD

GRAND TOTAL 61,35,99,820.37

GRAND TOTAL 61,35,99,820.37

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m

1 2.6 in width as well as 10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and for all lift, as directed by Engineer-

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m

2 2.7 in width as well as 10 sqm on plan) including getting out and disposal of 0.00 0.00

excavated earth lead upto 50 m and lift upto 1.5 m, as directed by

Engineer-incharge.

Extra for every additional lift of 1.5 m or part thereof in excavation /

banking excavated or stacked materials.

Excavating trenches by mechanical / manual means of required width for

pipes, cables, etc including excavation for sockets, and dressing of sides,

ramming of bottoms, for all depth, including getting out the excavated

soil, and then returning the soil as required, in layers not exceeding 20

cm in depth, including consolidating each deposited layer by ramming,

watering, etc. and disposing of surplus excavated soil as directed, within

a lead of 50 m :

a) 2.10.1 All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming and watering, lead up to

50 m and lift upto 1.5 m.

Carriage of Earth by mechanical transport including loading, unloading

6 1.1.2 and Stacking including royalty & carriage up to 5 KM complete. Cum 248.62 126.45 24.75 400.00 326.68 317.86 127144.00

Carriage of Excavated rock by mechanical transport including loading,

7 1.1.4 unloading and Stacking including royalty & carriage up to 5 KM Cum 1757.50 1200.31 787.65 3745.00 522.70 508.59 1904659.00

Supplying and filling in plinth with sand under floors including, watering,

ramming consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and

9 2.28.1 inequalities not exceeding 15 cm deep and disposal of rubbish, lead up Sqm 2014.38 1450.11 985.68 4450.00 34.15 33.23 147864.00

to 50 m and lift up to 1.5 m. All kinds of soil.

Supplying chemical emulsion in sealed containers including delivery as

i 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 231.69 150.37 111.18 493.00 234.75 228.41 112607.00

Anti termite treatment 0.00 0.00

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL

11 2.35 anti-termite treatment (excluding the cost of chemical emulsion) : 0.00 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Treatment of soil under existing floors using chemical emulsion @ one

litre per hole, 300 mm apart including drilling 12 mm diameter holes and

plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match

the existing floor :

i 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. Sqm 1737.68 1127.79 833.88 3699.00 310.05 301.68 1115909.00

TOTAL (Carried Over to Summary of Civil Works) 0.00 9161344.00 0.00

B 4.0 CONCRETE WORKS 0.00

Providing and laying in position cement concrete of specified grade

1 4.1 excluding the cost of centering and shuttering - All work up to plinth 0.00

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources :

i 4.1.5 6 graded stone aggregate 20 mm nominal size derived from natural Cum 2.17 0.74 0.41 3.00 7294.70 7097.74 21293.00

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources :

ii 4.1.8 8 graded stone aggregate 40 mm nominal size derived from natural Cum 270.91 169.74 110.77 551.00 6812.00 6628.08 3652070.00

Centering and shuttering including strutting, propping etc. and removal

of form work for :

i 4.3.1 Foundations, footings, bases for columns Cum 314.19 170.48 146.96 632.00 392.15 381.56 241147.00

Providing and laying damp-proof course 50mm thick with cement

concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

sources : 4 graded stone aggregate 20mm nominal size derived from

natural sources).

Extra for providing and mixing water proofing material in cement

4 4.12 concrete work in doses by weight of cement as per manufacturer's 21.71 14.78 12.53 49.00 18.15 17.66 865.00

Providing & applying a coat of residual petroleum bitumen of grade of

VG-10 of approved quality using 1.7kg per square metre on damp proof

course after cleaning the surface with brushes and finally with apiece of

cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded

stone aggregate 20 mm nominal size derived from natural sources) over

6 4.17 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed Sqm 229.11 150.53 131.07 511.00 749.30 729.07 372554.00

and consolidated and grouted with fine sand, including necessary

excavation, levelling & dressing & finishing the top smooth.

TOTAL (Carried Over to Summary of Civil Works) 0.00 4407222.00 0.00

C 5.0 REINFORCED CEMENT CONCRETE WORK 0.00

Centering and shuttering including strutting, propping etc. and removal

Foundations, footings, bases of columns, etc. for mass

Walls (any thickness) including attached pilasters, butteresses, plinth and

string courses etc.

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 7053.87 5157.80 3516.83 15728.00 927.25 902.21 14190026.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

e 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 6699.81 3657.76 2950.95 13309.00 736.40 716.52 9536127.00

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 3240.50 3003.75 2799.69 9044.00 961.30 935.34 8459259.00

g 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 344.48 47.25 262.70 654.00 764.95 744.30 486770.00

Extra for shuttering in circular work (20% of respective centering and

shuttering items)

Small lintels not exceeding 1.5m clear span, moulding as in cornices,

i 5.9.15 window sills, string courses, bands, copings, bed plates, anchor blocks Sqm 61.19 72.04 60.71 194.00 392.15 381.56 74023.00

j 5.9.16 Edges of slabs and breaks in floors and walls 0.00 0.00

k 5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 50.00 40.97 31.81 123.00 951.10 925.42 113827.00

Extra for additional height in centering, shuttering where ever required

with adequate bracing, propping etc., including cost of de-shuttering and

2 5.11 decentering at all levels, over a height of 3.5 m, for every additional 0.00 0.00

height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be

Steel reinforcement for R.C.C. work including straightening, cutting,

3 5.22 bending, placing in position and binding all complete upto plinth level. 0.00 0.00

i 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 71345.56 37117.46 17495.52 125959.00 107.85 104.94 13217892.00

Steel reinforcement for R.C.C. work including straightening, cutting,

4 5.22A bending, placing in position and binding all complete above plinth level. 0.00 0.00

i 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 458879.54 231562.66 136920.41 827363.00 107.85 104.94 86821860.00

Providing and laying in position ready mixed or site batched design mix

cement concrete for reinforced cement concrete work; using coarse

aggregate and fine aggregate derived from natural sources, Portland

Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

5 5.33 recommended proportions as per IS: 9103 to accelerate / retard setting 0.00 0.00

of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the

a) 5.33.1 following grades

All works upto of concrete.

plinth level Note: Extra cement up to 10% of the 0.00 0.00

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

b) 5.33.2 All works above plinth level upto floor V level 0.00 0.00

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Add for using extra cement in the items of design mix over and above

the specified cement content therein.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four

floors or part thereof.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing of expansion joint system related with floor location as per

drawings and direction of Engineer-In-Charge. The joints system will be of

extruded aluminum base members, self aligning / self centering arrangement

and support plates etc. as per ASTM B221-02. The system shall be such that it

provides floor to floor /floor to wall expansion control system for various

8 5.44 vertical localtion in load application areas that accommodates multi directional 0.00 0.00

seismic movement without stress to it's components. System shall consist of

metal profiles with a universal aluminum base member designed to

accommodate various project conditions and finish floor treatments. The cover

plate shall be designed of width and

thickness required to satisfy projects movement and loading requirements and

secured to base members by utilizing manufacturer’s pre-engineered self-

centering arrangement that freely rotates / moves in all directions. The Self –

centering arrangement shall exhibit circular sphere ends that lock and slide

inside the corresponding aluminum extrusion cavity to allow freedom of

movement and flexure in all directions including vertical displacement. Provision 0.00 0.00

of Moisture Barrier Membrane in the Joint System to have watertight joint is

mandatory requirement all as per the manufactures design and as approved by

Engineer -in- Charge . (Material shall confirm to ASTM 6063.)

Providing and fixing of expansion joint system related with wall joint

(internal/external) location as per drawings and direction of Engineer-In-

Charge. The joints shall be of extruded aluminum base members, self aligning /

centering arrangement and support plates as per ASTM B221- 02. The material

shall be such that it provides an Expansion Joints System suitable for vertical

wall to wall/ wall to corner application, both new and existing construction in

office Buildings & complexes with no slipping down tendency amongst the

components of the Joint System. The Joint System shall utilize light weight

aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically

snap locking the multicellular to facilitate movement. (Material shall confirm to

Providing and fixing of expansion joint system of approved make and

manufactures for various roof locations as per approved drawings and direction

of Engineer-In-Charge. The joints shall be of extruded aluminum base members

with, self aligning and self centering arragement support plates asper ASTM

B221-02. The system shall be such that it provides watertight roof to roof/roof

10 5.46 to corner joint cover expansion control system that is capable of 0.00 0.00

accommodating multidirectional seismic movement without stress to its

components. System shall consist of metal profile that incorporates a universal

aluminum base member designed to accommodate various project conditions

and roof treatments.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

The cover plate shall be designed of width and thickness required to satisfy

movement and loading requirements and secured to base members by utilizing

manufacturer’s pre-engineered self-centering arrangement that freely rotates /

moves in all directions. The Self centering arrangement shall exhibit circular

sphere ends that lock and slide inside the corresponding aluminum extrusion

cavity to allow freedom of movement and flexure in all directions including

vertical displacement. The Joint System shall resists damage or deterioration

from the impact of falling ice, exposure to UV, airborne contaminants and

occasional foot traffic from maintenance personnel. Provision of Moisture

Barrier Membrane in the Joint System to have water tight joint is mandatory

requirement. Material shall confirm to ASTM 6063.

TOTAL (Carried Over to Summary of Civil Works) 0.00 193156592.00 0.00

D 6.0 BRICK WORK 0.00

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in:

Providing and laying autoclaved aerated cement blocks masonry with

150mm/230mm/300 mm thick AAC blocks in super structure above

plinth level up to floor V level with RCC band at sill level and lintel level

2 6.47 with approved block laying polymer modified adhesive mortar all Cum 1492.63 688.64 680.34 2862.00 8333.65 8108.64 23206932.00

complete as per direction of Engineer-in-Charge. (The payment of RCC

band and reinforcement shall be made for seperately).

Extra for brick work / AAC block masonry / Tile brick masonry in

3 6.5 superstructure above floor V level, for each four floors or part thereof by Cum 99.18 164.70 157.97 422.00 169.45 164.87 69577.00

mechanical means.

Extra for half brick masonry in superstructure, above floor V level for

every four floors or part thereof by mechanical means.

Providing and laying autoclaved aerated cement blocks masonry with

100 mm thick AAC blocks in super structure above plinth level up to floor

5 6.38 V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate Cum 163.08 238.36 141.17 543.00 10195.45 9920.17 5386654.00

includes providing and placing in position 2 Nos 6 mm dia M.S. bars at

every third course of masonry work.

TOTAL (Carried Over to Summary of Civil Works) 0.00 28833270.00 0.00

E 8.0 MARBLE & GRANITE WORK 0.00

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms, vanity

counters, window sills, facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing,

curing, moulding and polishing to edges to give high gloss finish etc.

complete at all levels.

a) 8.2.2 Granite stone slab colour black, Cherry/Ruby red 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing edge moulding to 18 mm thick marble stone counters, Vanities

etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge. Granite work

Extra for providing opening of required size & shape for wash basins/

kitchen sink in kitchen platform, vanity counters and similar location in

3 8.5 marble/Granite/Stone work including necessary holes for pillar taps etc. Each 90.00 80.00 70.00 240.00 978.70 952.28 228546.00

including rubbing and polishing of cut edge etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and

polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal

partitions by cutting a chase of appropriate width with chase cutter and

4 8.10 embedding the stone in the chase with epoxy grout or with cement 0.00

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6

mm nominal size) as per direction of Engineer-in-charge and finished

i 8.10.2 Granite Stone of approved shade Sqm 22.50 21.15 44.00 4051.85 3942.45 173468.00

Providing and fixing machine cut, mirror/ eggshell polished, Granite

stone work for wall lining (veneer work) including dado, skirting, risers of

steps etc., in required design and pattern wherever required, stones of

different finished surface texture, on 12mm (average) thick cement

Refer DSR- mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement

5 2023 slurry @ 3.3 kg/sqm including pointing with white cement slurry Sqm 77.10 2.63 48.72 128.00 8625.70 8392.81 1074279.00

(8.11.1) admixed with pigment of matching shade, including rubbing, curing,

polishing etc. all complete as per Architectural drawings, and as directed

by the Engineer-in-Charge. Granite of colour black, cherry/ruby red 18-

20mm thick (slab area above 0.50 sqm)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved

make, in all colours, shades except burgundy, bottle green, black of any

size as approved by Engineer-in-Charge, in skirting, risers of steps and

dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing Glass Reinforced Concrete (G.R.C) product casted

with 'Design Mix' concrete design in approved size, pattern, thickness.

The GRC should be made from ‘53 grade’ white portland cement

manufactured by approved makes,fine graded sieve silica sand, Alkali

Resistant Glass Fibre , super plasticizers manufactured by approved

makes, Polymers manufactured by approved makes and U.V resistant

Synthetic inorganic pigments should be used for pigment action

manufactured by approved makes. The fixing of GRC should be done

using ‘Dry Fixing’ method into structural support members i.e R.C.C,

7 MR-1 Brick work or red oxide primer -paint or Epoxy primer-paint treated mild Sqm 6955.21 6955.00 0.00 8268.00 57503940.00

steel. The fixtures, fasteners and self tapping screws to be used for dry

fixing should be of approved makes. The quantity of fasteners or self

tapping screws shall be calculated in accordance to the weight of GRC

and actual site fixing conditions. Vendor shall submit shop drawings of

the same, the drawings to be duly approved from engineer in-charge at

site. GRC Stone finish cladding with 20-25mm thickness as per approved

design and shade.

Providing & erection of the MS structural framework as per approved

8 MR-2 shop drawing for stone finish cladding (Approx - 4Kg per sqft) with a kg 262030.63 262031.00 0.00 206.00 53978386.00

single paint coat.

Designing, fabricating, testing, installing and fixing in position Curtain

Wall with Aluminium Composite Panel Cladding, with open grooves for

linear as well as curvilinear portions of the building , for all heights and

all levels etc. including: (a) Structural analysis & design and preparation

of shop drawings for pressure equalisation or rain screen principle as

required, proper drainage of water to make it watertight including

checking of all the structural and functional design. (b) Providing,

fabricating and supplying and fixing panels of aluminium composite

panel cladding in pan shape in metalic colour of approved shades made

9 8.32 out of 4mm thick aluminium composite panel material consisting of 0.00

3mm thick FR grade mineral core sandwiched between two Aluminium

sheets (each 0.5mm thick). The aluminium composite panel cladding

sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based

fluoropolymer resin coating of approved colour and shade on face # 1

and polymer (Service) coating on face # 2 as specified using stainless

steel screws, nuts, bolts, washers, cleats, weather silicone sealant,

backer rods etc.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip

Galvanised with serrations and serrated washers to arrest the wind load

movement, fasteners, SS 316 Pins and anchor bolts of approved make in

SS 316, Nylon separators to prevent bi-metallic contacts all complete

required to perform as per specification and drawing The item includes

cost of all material & labour component, the cost of all mock ups at site,

cost of all samples of the individual components for testing in an

approved laboratory, field tests on the assembled working curtain wall

with aluminium composite panel cladding, cleaning and protection of

the curtain wall with aluminium composite panel cladding till the

i i handing over of the building for occupation. The Contractor shall provide Sqm. 50.00 10.00 10.00 70.00 5015.05 4879.64 341575.00

curtain wall with aluminium composite panel cladding,and including

base frame work for ACP having all the performance characteristics all

complete , as per the Architectural drawings, as per item description, as

specified, as per the approved shop drawings and as directed by the

Engineer-in-Charge. However, for the purpose of payment, only the

actual area on the external face of the curtain wall with Aluminum

Composite Panel Cladding (including width of groove) shall be measured

in sqm. up to two decimal places.

TOTAL (Carried Over to Summary of Civil Works) 0.00 8645642.00 111482326.00

F 9.0 WOOD & PVC WORK 0.00

Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or with

dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be

paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction with

2 9.21 frame of 1st class hard wood and well matched commercial 3 ply 0.00 0.00

veneering with vertical grains or cross bands and face veneers on both

faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

3 9.23 minimum depth on all edges of flush door shutters (over all area of door Sqm 81.81 84.74 71.07 238.00 462.35 449.87 107068.00

shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with

4 9.40.1 iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd 0.00 0.00

class teak wood

Providing and fixing M.S. grills of required pattern in frames of windows

5 9.48 etc. with M.S. flats, square or round bars etc. including priming coat with 0.00 0.00

approved steel primer all complete.

i 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. kg 4123.80 3349.80 2897.10 10371.00 238.35 231.91 2405186.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing curtain rods of 1.25 mm thick chromium plated

brass plate, with two chromium plated brass brackets fixed with C.P.

brass screws and wooden plugs, etc., wherever necessary complete :

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with

10 mm diameter bolts, nuts and wooden plugs and embedding in cement

concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone

aggregate 20mm nominal size).

Providing and fixing aluminium tower bolts ISI marked anodised (anodic

coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium pull bolt lock, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868) transparent or

dyed to required colour and shade, with necessary screws bolts, nut and

washers etc. complete.

Providing and fixing aluminium handles of approved make anodized

(anodic coating not less than grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade with necessry screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt / suede finish with high density protective

11 9.127 surface layer and reverse side of adhesive bonding quality conforming to 0.00 0.00

IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing factory made uPVC door frame made of uPVC

extruded sections having an overall dimension as below (tolerance

±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door

frame to be Jointed with galvanized brackets and stainless steel screws,

12 9.117 joints mitred and Plastic welded. The hinge side vertical of the frames 0.00 0.00

reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1

mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame

complete as per manufacturer’s specification and direction of

Engineer in-charge

13 9.118 Providing and fixing to existing door frames. 0.00 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of

styles and rails of a uPVC hollow section of size 60x30 mm and wall

thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on

one side. The styles and rails mitred and joint at the corners by means of

M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness

1.0 mm and stainless steel screws. The styles of the shutter reinforced by

inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm)

wall thickness. The lock rail made up of 'H' section, a uPVC hollow

i 9.118.2 section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to Sqm 17.33 143.33 127.58 288.00 3253.80 3165.95 911793.00

the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The

shutter frame filled with a uPVC multi-chambered single panel of size not

less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1

mm) wall thickness . The panels filled vertically and tie bar at two places

by inserting horizontally 6 mm galvanised M.S. rod and fastened with

nuts and washers, complete as per manufacturer's specification and

direction of Engineer-in-charge.

Providing and fixing partition upto ceiling height consisting of G.I. frame and

required board, including providing and fixing of frame work made of special

section power pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm

wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and

ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm

dia meter 50 mm length or suitable anchor fastener or metal screws with nylon

plugs and the studs 48 mm wide having one flange of 34 mm and other flange

36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling

channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

and nuts, including fixing of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing of 450

mm centre to centre, and fixing of boards to both side of frame work by 25 mm

long dry wall screws on studs, floor and ceiling channels at the spacing of 300

mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks,

M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm

each) to be provided at the horizontal joints of two boards, fixed to the studs

using metal to metal flat head screws, including jointing and finishing to a flush

finish with recommended jointing compound, jointing tape, angle beads at

corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer

suitable for board as per manufacture’s specification and direction of engineer

in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated

i 9.105.1 Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 Sqm 50.00 10.00 25.00 85.00 2131.10 2073.56 176253.00

(Board with BIS certification marks)

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing factory made uPVC glazed/ wire mesh

windows/ doors comprising of lead free uPVC multichambered frame, sash and

mullion/ coupler (wherever required) extruded profiles having minimum wall

thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3

and R4 profiles conforming to EN: 12608 in any shape, colour and design duly

reinforced with galvanized mild steel section made of required shape & size as

per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash

adaptor (whereever required) of appropriate dimension, EPDM gasket,

hardware, SS 304 grade fasteners of minimum 8 mm dia. with countersunk

head, comprising of matching polyamide PA6 grade sleeve for fixing frame to

finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and

necessary stainless steel screws etc. Profile of frame, sash & mullion (if

required) shall be mitred cut and fusion welded/mechanically jointed duly

sealed at all corners, including drilling of holes for fixing hardware and drainage

of water etc. After fixing frame the gap between frame and adjacent finished

wall shall be filled with weather proof silicon sealant over backer rod of

approved size and quality, all complete as per approved drawing conforming to

CPWD specification & direction of Engineer-in-Charge. Section of steel

reinforcement and cross sections of uPVC profiles to be as per design approved

by Engineer-in-Charge.

Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/

without high performance coatings as per design requirements and conforming

to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof

checked from a Government Engineering Institute, to be provided by the 0.00 0.00

manufacturer for : (iii) Sites with basic wind speed > 45 m/sec as per IS 875 –Part

3 (iv) Sites with structure height more than 20m for all wind speeds

9.147.A3 Two and half track three panels sliding window with two glazed & one wire

a) mesh panels with Aluminium channel for roller track, wool pile, nylon rollers 0.00 0.00

with SS 304 body.

9.147.A3.2 Using R3 series with frame (85mm & above) x (40mm & above) & glazed sash

(30mm & above) x (55mm & above) & fly screen sash (20mm & above) x (50mm

i & above) with zinc alloy (zamak) powder coated handle on every glazed panel Sqm 98.42 17.42 24.30 140.00 9968.70 9699.55 1357936.00

along with multi-point locking system. (Height upto 1.8 meter).

Three track three panels sliding window with two glazed & one wire mesh

b) 9.147.A4 panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 0.00 0.00

Using R4 series with frame (115mm & above) x (45mm & above) & both glazed

and fly screen sash (44mm & above)

x (55mm & above) with zinc alloy (zamak) powder coated

touch locks with hook. (Height upto 1.8 meter).

c) 9.147.C1 Fixed window / ventilator without mullion / transom. 0.00 0.00

Using R1 series with frame (33mm & above ) x (35mm & above). (Height upto

Casement door double panel with French (False) Mullion with zinc alloy

d) 9.147.F2 (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy 0.00 0.00

(zamak) powder coated handles on both sides.

Using R3 series with frame (55 mm & above) x (50mm & above) & sash

above) x (60mm & above). (Height upto 2.5 meter).

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing zinc alloyed (white powder coated) touch lock for

uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary

screws etc. complete.

Providing and fixing steel roller for uPVC sliding door with necessary

screws etc. complete.

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid door/ window/ Ceosetory windows & other Frames/

Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension

Grade), calcium carbonate and natural fibers (wood powder/ rice husk/

wheat husk) and non toxic additives (maximum toxicity index of 12 for

100 gms) fabricated with miter joints after applying PVC solvent cement

and screwed with full body threaded star headed SS screws having

16 26.86 minimum frame density of 750 kg/cum, screw withdrawal strength of 0.00 0.00

2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58

N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of

flame of Class A category with property of being termite/ borer proof,

water/ moisture proof and fire retardant and fixed in position with M.S

hold fast/ lugs/ SS dash fasteners of required dia and length complete as

per direction of Engineer-In- Charge.

(M.S hold fast/ lugs or SS dash fasteners shall be paid for separately).

Note: For WPC solid door/ window frames, minus 5mm tolerance in

dimensions i.e depth and width of profile shall be acceptable. 0.00 0.00

Variationin profile dimensions on plus side shall be acceptable but no

extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid decorative type flush door shutter of required size

comprising of virgin polymer of K value 58-60 (Suspension Grade),

calcium carbonate and natural fibers (wood powder/ rice husk/wheat

husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)

having minimum density of 650 kg/cum and screw withdrawal strength

of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50

N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of

17 26.88 flame of Class A category with property of being termite/borer proof, 0.00 0.00

water/moisture proof and fire retardant. WPC to be laminated with PVC

foil of minimum 14 microns thick of approved design pasted with hot

melt adhesive on both faces of shutter and fixing with stainless steel butt

hinges of required size with necessary full body threaded star headed

counter sunk S.S screws, all as per direction of Engineer-In- Charge.

(Note: stainless steel butt hinges and necessary S.S screws shall be paid

Providing and fixing IS : 12817 marked stainless steel butt hinges with

stainless steel screws etc. complete :

SS Hardware 0.00 0.00

Providing and fixing bright /matt finished Stainless Steel handles of approved

quality & make with necessary screws etc all complete.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing Stainless Steel tower bolts of approved make with

necessary screws etc. complete :

Providing and fixing Stainless Steel hanging floor door stopper of approved

make with necessary screws etc. complete.

Providing and fixing Concealed Door Closer With Track Arm (SS Finish), Slide in

SS Cover Stainless Steel door closer, door weight upto 80 kg and door width

from 701 mm to 1000 mm), with double speed adjustment with necessary

accessories and screws etc. complete.

Providing and fixing of Mortise Lock with Handles Stainless Steel Finish (Solid

23 MR-6 Casted) with necessary screws etc. complete as per design & approved by Each 136.00 31.00 36.00 203.00 0.00 5210.85 1057803.00

Engineer in Charge.

Providing and fixing stainless steel sliding door bolts, ISI marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed

to required colour or shade, with nuts and screws etc. complete : 300x16 mm

25 MR-8 Providing and fixing Stainless steel Al-drop Each 11.00 91.00 81.00 183.00 0.00 373.90 68424.00

Providing and fixing fire resistant door frame of section 50 x 60 mm on

horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of

1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for

mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled

with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a

provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on

26 9.161 horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Rmt 108.30 108.00 2202.90 2143.42 231490.00

Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing

of fire rated glazed shutter . The frame shall be finished with a approved fire

resistant primer or Powder coating of not less than 30 micron in desired shade

as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min

Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified

as per laboratory approved by Engineer-in-charge, with suitable mounting on

door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide

and bottom rail of 110 mm x 60mm made out of 1.6mm thick G.I. sheet (zinc

coating not less than 120gm/m²) duly filled mineral wool insulation having

density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing

hinges of size 100x89x3mm of approved make, including applying a coat of

approved fire resistant primer or powder coating not less than 30 micron etc all

complete as per direction of Engineer-in-charge (panelling to be paid for

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing glazing in fire resistant door shutters, fixed panels &

partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc

coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm

SS screws at distance 75 mm from the edges and 150 mm c/c , including

applying a coat of approved fire resistant primer/powder coating of not less

than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc

complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per

direction of Engineer-in-charge with glass of required thickness having 120

minutes of fire resistance both integrity & radiation control (EW120) and

minimum 20 minutes of insulation (EI20). The manufacturer have to give test

report/certification of fire glass and the glass should have the stamp showing

the value of E, EW & EI. The glass shall be tested in approved NABL accredited

lab or by any other accreditation body which operates in accordance with

ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration

scopes shall be eligible. The maximum glazing size shall not be more than

1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body,

Trim Latch & Lock on back side of the Panic Latch of reputed brand and

manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing certified restroom cubicle system of approved make

comprising of green guard certified solid compact laminated water proof board,

minimum 18 mm thick made as per IS: 2046 (phenolic core board) and as per BS-

476/97 for fire retardant for toilet showers, water closet etc . The board shall be

manufactured under high pressure and temperature by impregnating kraft

papers and outer decorative papers with thermosetting phenolic/ melamine

resins (low VOC). The cubicle system shall be resistant towards water, chemical,

scratch, impact and heat and shall be anti bacterial, colour fast and shall have

accessories like door knob, Gravity/ auto return hinges, privacy thumb turn with

occupancy indicator, coat Hook, etc all in SS 304. The hardware and fixings

includes anchoring of all fixed front panel to floor with SS 316 L brackets/ base

plates with a clearance height upto 110 mm, and covered with SS 316 Shoe box

plates, wall and corner joineries (brackets and channels) shall be SS 304 grade,

SS 304 sr ISO/IEC 17025 for testing and calib

The cubicle unit shall be installed in approved finish, shades and colours as per

specifications and directions of Engineer-In-Charge, including minimum 5 (five)

years warranty against any moisture related damages to all intermediate panels,

doors, hardqwares etc. Standard dimension of the cubicle system shall be of 0.00

approx. 2100 mm Height(overall) x 1500mm Depth and 1200 mm Width which

includes 600mm door size width.

I shaped Cubicle System consisting of front face panel including door and all

necessary accessories, fittings and hardware etc.

L shaped Cubicle System consisting of front face panel including door,

ii ii intermediate panel and all necessary accessories, fittings and hardware etc. Each 60.00 79.00 61.00 100.00 0.00 49812.00 4981200.00

TOTAL (Carried Over to Summary of Civil Works) 0.00 30246670.00 10723466.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

G 10.0 STEEL WORK 0.00

Structural steel work riveted, bolted or welded in built up sections,

1 10.2 trusses and framed work, including cutting, hoisting, fixing in position Kg 150.00 90.00 90.00 330.00 133.70 130.09 42930.00

and applying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of

2 10.5 40x40x6mm angle iron and 3 mm M.S. gusset plates at the junctions and 0.00

corners, all necessary fittings complete, including applying a priming coat

of approved steel primer.

i 10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces Sqm 5.04 5.04 5.04 15.00 5804.35 5647.63 84714.00

Providing and fixing pressed steel door frames conforming to IS: 4351,

manufactured from commercial mild steel sheet of 1.60 mm thickness,

including hinges, jamb, lock jamb, bead and if required angle threshold

of mild steel angle of section 50x25 mm, or base ties of 1.60 mm,

3 10.14 pressed mild steel welded or rigidly fixed together by mechanical means, 0.00 0.00

including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock

strike-plate and shock absorbers as specified and applying a coat of

approved steel primer after pre-treatment of the surface as directed by

Engineer-in-charge:

i 10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb Rmt 0.00 0.00 583.30 567.55 0.00

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.)

trusses etc., including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer, including welding and bolted with special shaped

washers etc. complete.

5 10.20 Providing and fixing bolts including nuts and washers complete kg 262.50 22.50 7.50 293.00 159.35 155.05 45429.00

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for

ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5

mm thick M.S. sheet with its top surface hacked for proper bonding, top

6 10.18 lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 each 425.00 330.00 160.00 915.00 220.65 214.69 196444.00

mm dia round headed screws, one lock at the corners. Clamp shall be

made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work including cutting,

7 10.25 hoisting, fixing in position and applying a priming coat of approved steel 0.00 0.00

primer using structural steel etc. as required

In stringers, treads, landings etc. of stair cases including use of

chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar

Providing and fixing carbon steel galvanised ( minimum coating 5

micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield

strength 480 N/mm2), counter sunk head, comprising of 10 m dia

polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing,

polishing and making curvature (wherever required) and fitting the same

with necessary stainless steel nuts and bolts complete, i/c fixing the

railing with necessary accessories & stainless steel dash fasteners ,

9 10.28 stainless steel bolts etc., of required size, on the top of the floor or the kg 2842.20 7385.18 7965.50 18193.00 772.40 751.55 13672862.00

side of waist slab with suitable arrangement as per approval of Engineer-

in-charge, (for payment purpose only weight of stainless steel members

shall be considered excluding fixing accessories such as nuts, bolts,

fasteners etc.).

TOTAL (Carried Over to Summary of Civil Works) 0.00 16408206.00 0.00

H 11.0 FLOORING WORK 0.00

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate) finished with a floating coat of neat cement, including

cement slurry, but excluding the cost of nosing of steps etc. complete.

i 11.3.1 40 mm thick with 20 mm nominal size stone aggregate Sqm 21.41 10.00 10.00 41.00 614.20 597.62 24502.00

Chequerred precast cement concrete tiles 22 mm thick in footpath

&courtyard, jointed with neat cement slurry mixed with pigment to

2 11.20 match the shade of tiles, including rubbing and cleaning etc. complete,

on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

i 11.20.1 Light shade pigment using white cement. Sqm 25.00 10.00 10.00 45.00 1402.00 1364.15 61387.00

Kota stone slab flooring over 20 mm (average) thick base laid over and

jointed with grey cement slurry mixed with pigment to match the shade

of the slab including rubbing and polishing complete with base of

cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars

laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse

4 11.27 sand) and jointed with grey cement slurry mixed with pigment to match Sqm 27.14 3.47 5.02 36.00 2354.70 2291.12 82480.00

the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing to treads of steps of marble / granite stone.

Extra for marble / granite stone flooring in treads of steps and risers

using single length up to 2.00 metre.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to

be specified by the manufacturer), of 1st quality conforming to IS : 15622, of

approved make, in all colours, shades, except White, Ivory, Grey, Fume Red

7 11.38 Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sqm 482.87 911.83 874.71 2269.00 1315.30 1279.79 2903836.00

sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the

joints with white cement and matching pigments etc., complete.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing & Laying vitrified floor tiles in different sizes ( thickness to be specified

by the manufacturer) with water absorption's less than 0.08% and confirming to

IS : 15622 of approved make in all colours and shades, laid on 20mm thick

cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with

white cement and matching pigments etc, complete.

Providing and laying Vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 % and

conforming to I.S. 15622, of approved make, in all colours & shade, in

9 11.46 skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 0.00 0.00

cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joint with white cement & matching pigments etc.

Providing and laying Polished Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all

complete as per the architectural drawings with 18 mm thick stone slab

over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4

coarse sand) laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade including

rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby

Red or equivalent

Providing and laying Laminate wooden

flooring (Grade AC6 or AC6+ laminates) 6 mm to 12 mm thick, having a good

backing layer made up of plastic laminate or melamine, core made up of

medium-density fibreboard (MDF),which is less resistant to impact damage and

less resistant to being dented by heavy furniture, having a décor layer to give

11 MR-10 each floor its appearance and consisting of one or more sheets of paper Sqm 22.85 0.00 23.00 0.00 2692.10 61918.00

impregnated with melamine resin and top wear layer having clear

aluminium oxide finish that protects the decorative layer & imparts the

desired level of sheen, from full gloss to low gloss, duly fixed to the base floor

using adhesive as approved by the manufacturer.

TOTAL (Carried Over to Summary of Civil Works) 0.00 40710956.00 61918.00

I 12.0 ROOFING 0.00

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 stone aggregate 10 mm and down gauge), including finishing

with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400

micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse

sand) and a coat of neat cement, rounding the edges and making and

finishing the outlet complete.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of

27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange

of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with

nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm

3 12.45 centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 0.00

mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire

at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry

wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with

the help of dry wall screws of size 3.5 x 25 mm edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings, grills, diffusers, 0.00

cutouts made with frame of perimeter channels suitably fixed, all complete as

per drawings, specification and direction of the Engineer in Charge but excluding

the cost of painting with : at 230 mm c/c, including jointing and finishing to a

flush finish of tapered and square

i 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board. Sqm 1498.71 1499.00 1529.10 1487.81 2230234.00

Providing and fixing precoated galvanised iron profile sheets (size, shape and

pitch of corrugation as approved by Engineer-in-Charge) of total coated

thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total

coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS:

277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet

and polyester top coat 15-18 microns. Sheet should have protective guard film

of 25 microns minimum to avoid scratches during transportation and should be

supplied in single length upto 12 metre or as desired by Engineer-in-charge. The

sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm)

with EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting

to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total

coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with

total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per

IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the

sheet and polyester top coat 15-18 microns using self drilling/ self tapping

screws complete :

ii 12.51.2 Flashings/ Aprons.( Upto 600 mm) metre 10.00 10.00 485.60 472.49 4725.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

iii 12.51.6 Gutter (600 mm over all girth) metre 20.00 20.00 1313.70 1278.23 25565.00

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm

in true horizontal level, suspended on inter locking metal grid of hot dipped

galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive)

consisting of main "T" runner with suitably spaced joints to get required length

and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at

1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm

thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm

center to center to form a grid of 1200x600 mm and secondary cross "T" of

length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to

be interlocked at middle of the 1200x600 mm panel to form grids of 600x600

mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of

approved texture in the grid including, required cutting/making, opening for

services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T"

runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25

x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm

GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm

spaced at 1200 mm center to center along main T, bottom exposed width of 24

mm of all T-sections shall be pre-painted with polyester paint, all complete for

all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size

595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having

galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with

1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro

statically polyester powder coated of thickness 60 microns (minimum), including

factory painted after bending and perforation, and backed with a black Glass

fiber acoustical fleece.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300mm x 20 mm)

with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance

> 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement

sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints

with mix of white cement & marble powder in ratio of 1:1, including rubbing and

polishing of the surface upto 3 cuts complete, including providing skirting upto

150 mm height along the parapet walls in the same manner.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and fixing of Baffle false ceiling system comprises 75 mm x 150 mm

(75 mm width and 150 mm Height) U Shape panels. Panels shall be made of 0.7

mm thick Aluminium sheet with wooden finish powder coating on the front side

with 60 microns powder coating. Length of the panel will be up to 3000 mm.

Panel shall be high corrosion resistance and good color stability. Panel to panel

gap will be 150 mm. Panels are fixed on to roll formed carriers 50 mm wide x 20

mm deep out of 0.75 mm G.I sheet powder coated with cutouts to hold the

panels in module of 150 mm at maximum 1200 mm c/c. Carriers are suspended

8 MR-11 from the roof or truss by 6 mm dia. galvanized thread rod hanger with height Sq.Mt. 1124.04 1124.00 0.00 7120.00 8002880.00

adjustment at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or

ceiling brackets and Fasteners. Panels are factory cut in lengths up to maximum

3000 mm to suit site dimensions or shop drawings. Top cap and side cap are

used to cover the edges of the panels. Inner cap and outer cap are used to nut

bolt the panel with carrier. These Baffles are light weight and do not add any

extra load on ceiling.

Providing and Fixing 15 mm thick densified tegular edged eco friendly light

weight calcium silicate false ceiling tiles of approved texture of size 595 x 595

mm in true horizontal level, suspended on inter locking metal grid of hot dipped

galvanised steel sections (galvanising @ 120 grams per sqm including both side)

consisting of main ‘T’ runner suitably spaced at joints to get required length and

of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm

centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm

(Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to

centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm

and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked

at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting

on periphery walls /partitions on a Perimeter wall angle pre-coated steel of

size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of

9 12.53 rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 Sq.Mt. 2997.43 2997.00 2158.15 2099.88 6293340.00

mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles

of approved texture in the grid, including, cutting/ making opening for services

like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever

required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats

of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash

fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x

30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom

exposed with 24 mm of all Tsections shall be pre-painted with polyster baked

paint, for all heights, as per specifications, drawings and as directed by Engineer-

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and Fixing of 16mm Thick sky lights consisting of Multi cell/tight cell

Polycarbonate Panel System of approved colour, 16 mm thick (minimum) having

uniform in color with an integral Tight-Cell core constructed not to exceed

4mmx4mm in a cross section, Vertical Standing Seam manufactured at both

sides of the panel. Snap-on connector to interlock the panels shall have a grip-

lock double tooth locking mechanism to ensure maximum uplift capability and

shall be of same color as that of panel. Panel shall be factory sealed/end welded

panels with additional End-cap/Aluminium U-Profile (mill finish) for ends. Panel

shall be co-extruded with special anti glare compound and UV protected. The

full system shall be fitted on MS purlins perpendicular to direction of sheeting

with purlin spacing as specified by Manufacturer. The rate includes cost of all

the operations, labour and all materials and tests (as applicable) involved such

as bolts nuts and screws etc. and labour for cutting bending to required profile,

necessary scaffolding, hoisting in position etc. for proper completion of the

work etc. complete as per specification drawings and direction of Engineer in

charge. Finished surface area of roofing fixed over steel tublar structure shall be

measured for payment. MS tabular frame work shall be measured separately for

Providing and fixing stretch ceiling at all heights and levels and of any shape

including wall coveing wherever shown on dawing as pe detailed specifications:

Detailed Description Features: System comprises of two components - A

perimeter track and lightweight fabric membrane. Ceiling manufactured from

roll material bespoke to ceilings height and shape. it shall have povision of

multiple ceiling removal and re-installation for access. it shall include

Incorporatiing of all types of light fixtures, grilles and fixing points including

Transmittance for Light Diffusion, Backlighting (LED) and projection. System

shall be entirely waterproof, washable. membane shall be 0.2mm thick PVC

(Polyvinyl Chloride) based membrane and shall be connected through

Membranes by Micro-Seams (Factory Welded). Semi-Concealed Perimeter

Track Matt White/Black PVC mateial fo fixing or Anodised Aluminium as per

TOTAL (Carried Over to Summary of Civil Works) 0.00 18572873.00 9079220.00

J 13.0 FINISHING WORK 0.00

1 13.4 12 mm cement plaster of mix : 0.00

15 mm cement plaster on rough side of single or half brick wall of mix :

3 13.6 20 mm cement plaster of mix : 0.00 0.00

4 13.16 6 mm cement plaster of mix : 0.00 0.00

Extra for providing and mixing water proofing material in cement plaster per bag

work in proportion recommended by the manufacturers. of 50KG

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Extra for plastering exterior walls of height more than 10 m from ground

level for every additional height of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over

7 13.26 plastered surface to prepare the surface even and smooth complete. Sqm 150.00 5061.45 3445.41 8657.00 262.70 255.61 2212791.00

Distempering with 1st quality acrylic distemper, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre, of approved

brand and manufacture, including applying additional coats wherever

required, to achieve even shade and colour.

Applying one coat of water thinnable cement primer of approved brand

and manufacture on wall surface :

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

Finishing walls with water proofing cement paint of required shade :

12 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and

including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing exterior walls with Ceramic textured finish with protection

coating by Ultratech Texture Paints (UTTPL) ( Natural - Ceramic/ Stony of

approved shade or approved equivalent make) to external wall surfaces

comprising of water-borne, penetrating, water repellent EM- primer &

super durable water based acrylic silicon resin clear and super durable

dirt and dust resistant protection coat of FSI Clear coat, which shall be

highly water repellant, Anti-algae & anti-fungal in nature. The coating

shall also cover hairline cracks with application method which includes 2

13 MR-14 coats of E M Primer, 2 coats (Silmultaneouly) of 100% natural Ceramic & Sqm 169.38 7972.69 4427.29 12569.00 2830.00 35570270.00

granite crushed stone , all in approved colour and texture including

preparation of surface, appropriate primer coat etc. applied as per

manufacturer's instructions complete & project consultant instructions,

allow for scaffolding, staging as required. The finish shall be natural

colour/ non pigmented, water repellant, resistant to condensate

formation, cover hairline cracks/ crazing, UV & alkali resistant & ensure

good breathability for the substrate all to complete as per direction of

Engineer-in-charge.

Finishing walls with Deluxe Multi surface paint system for interiors and

exteriors using Primer as per manufacturers specifications :

Painting wood work with Deluxe Multi Surface Paint of required shade.

Two or more coat applied @0.90 ltr/10 sqm over an under coat of

primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

15 13.85 Applying priming coat : 0.00 0.00

With ready mixed pink or Grey primer of approved brand and

manufacture on wood work (hard and soft wood)

With ready mixed red oxide zinc chromate primer of approved brand

and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

Add for plaster drip course/ groove in plastered surface or moulding to

R.C.C. projections.

Providing and applying white cement based putty of average thickness 1

mm, of approved brand and manufacturer, over the plastered wall

surface to prepare the surface even and smooth complete

Providing factory made 25 mm thick single extruded WPC (Wood Polymer

Composite) solid plain white colour board Jali, CNC (Computer numeric control)

routed of approved design by Engineer-in -charge which are machine cut for

duct/shaft covering, partitions and facades comprising of virgin polymer of K

value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood

powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index

of 12 for 100 gms) having minimum density of 650 kg/cum and screw

withdrawal strength of 1800 N (Face) minimum compressive strength 50

N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of

20 Class A category with properties of being termite/borer proof, water/moisture Sqm 72.45 293.16 77.42 443.00 3939.34 3832.98 1698009.00

proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x

1.5 mm square hollow box section including applying a priming coat of approved

steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site

with necessary stainless steel fasteners and SS screws etc., all complete as per

direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming

coat and necessary SS fasteners and SS screws shall be paid separately.

Supply and Installation of 6mm thick FR Grade Aluminium Composite HPL

Composite Panel Cladding of approved color, made out of 5.5mm thick FR grade

mineral core sandwiched between two aluminium sheets (each 0.25mm thick).

The Aluminium HPL Composite Panel Cladding shall be coil coated with High

Durable resin coating of approved colour with 10 years exterior warranty and

shade on face #1 and polymer (service) coating on face #2. Installation of panels

will be done by MBE Rivets (with Fixed and Sliding Points) with recommended

Aluminum T section of 75x37x2.8 mm thick and L section 38x38x2.8mm thick

21 MR-15 held by Aluminum Wall Bracket with Wind load and Dead load slot, anchored by Sqm 640.00 62.00 55.00 757.00 7558.15 5721520.00

standard anchor fasteners along with Thermal Separator. Installation of Panels

will be done using Rear Ventilated Principles only, which is ensured by providing

ventilation gap minimum 200 cm2/ per Meter (for free flow of air behind the

façade) for the façade and using the framework with no horizontal section. (for

all levels and all height cracks/ crazing, UV & alkali resista

TOTAL (Carried Over to Summary of Civil Works) 0.00 44845403.00 41291790.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

K 16.0 ROAD WORK 0.00

Preparation and consolidation of sub grade with power road roller of 8 to 12

tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing

to camber and consolidating with road roller including making good the

undulations etc. and re roller including making good the undulations etc. and re-

rolling the sub grade and disposal of surplus earth lead upto 50 metres.

Supplying and Stacking of Good Earth by mechanical transport including loading,

2 16.3.9 unloading including royalty & carriage up to 5 KM complete. Cum 893.00 612.00 361.00 1866.00 775.50 754.56 1408012.00

Spreading of sludge, dump manure and/or good earth in required thickness and

extra for compaction of earth work as per direction of officer-in-charge (cost of

sludge, dump manure and/ or good earth to be paid separately).

4 16.3 Supplying and stacking at site. 0.00 0.00

iv 16.3.6 Stone screening 13.2 mm nominal size (Type A) Cum 37.50 54.30 24.81 117.00 2034.35 1979.42 231592.00

v 16.3.7 Stone screening 11.2 mm nominal size (Type B) Cum 37.50 54.30 24.81 117.00 2247.75 2187.06 255886.00

Laying, spreading and compacting stone aggregate of specified sizes to WBM

specifications in uniform thickness, hand picking, rolling with 3 wheeled

road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber,

applying and brooming requisite type of screening / binding material to fill up

interstices of coarse aggregate, watering and compacting to the required density

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from

batching plant. The ready mixed concrete shall be laid and finished with screed

board vibrator , vacuum dewatering process and finally finished by floating,

brooming with wire brush etc. complete as per specifications and directions of

Engineer-incharge. (The panel shuttering work shall be paid for separately).

(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less

cement used as per design mix is payable/ recoverable separately).

Extra for providing and mixing hardening compound of approved quality as per

manufacturer’s specification in cement concrete.

Providing and fixing in position pre-moulded joint filler in expansion joints. per cm

Providing and laying in position bitumen hot sealing compound for expansion

joints etc. Using grade ‘A’ sealing compound.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and applying 2.5 mm thick road marking strips (retroreflective) of

specified shade/ colour using hot thermoplastic material by fully/ semi

automatic thermoplastic paint applicator machine fitted with profile shoe, glass

beads dispenser, propane tank heater and profile shoe heater, driven by

10 16.62 experienced operator on road surface including cost of material, labour, T&P, Sqm 56.00 81.00 37.00 174.00 747.80 727.61 126604.00

cleaning the road surface of all dirt, seals, oil, grease and foreign material etc.

complete as per direction of Engineer-in-charge and accordance with applicable

specifications.

Providing, laying and making kerb channel 30 cm wide and 50 mm thick with

cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20

mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well

rammed and consolidated and grouted with fine sand, including finishing the

top smooth etc. complete and as per direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25

grade cement concrete in position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making

joints with or without grooves (thickness of joints except at sharp curve shall not

12 16.69 to more than 5mm), including making drainage opening wherever required Cum 8.00 12.00 6.00 26.00 9844.42 255955.00

complete etc. as per direction of Engineer-in-charge (length of finished kerb

edging shall be measured for payment). (Precast C.C. kerb stone shall be

approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver

blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of

required strength, thickness & size/ shape, made by table vibratory method

using PU mould, laid in required colour & pattern over 50mm thick compacted

bed of sand, compacting and proper embedding/laying of inter locking paver

13 16.91.1 blocks into the sand bedding layer through vibratory compaction by using plate Sqm 1500.00 271.50 124.05 1896.00 1017.42 1929023.00

vibrator, filling the joints with sand and cutting of paver blocks as per required

size and pattern, finishing and sweeping extra sand. complete all as per

direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-

35 grade with approved colour, design & pattern.

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm

thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate

14 11.45 and base course and filling with 150 mm thick jamuna sand, including spreading, Sqm 10.00 10.00 10.00 30.00 1661.98 49859.00

well ramming, consolidating and finishing smooth etc. all complete as per

direction of Engineer-in-charge. 1708.1

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel

dressed on top, for paving in floors, drains etc. laid over 20mm thick base

15 16.92 mortar 1:4 (1cement:4 coarse sand) with joints 10mm wide filled with same Sqm 10.00 10.00 10.00 30.00 2130.04 63901.00

mortar including ruled pointing etc. complete as per direction of engineer-in

charge. 2189.15

Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including

collars/spigot jointed with stiff mixture of cement mortar in the proportion of

16 19.36 1:2 (1 cement : 2 fine sand) including testing of joints etc. 0.00 0.00

TOTAL (Carried Over to Summary of Civil Works) 0.00 10839494.00 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

L DSR-2020 HORTICULTURE AND LAND SCAPING 0.00

Supplying and stacking at site dump manure from approved source, including

1 2.4 carriage upto 5 km complete (manure measured in stacks will be reduced by 8% 0.00

i 2.4.2 Screened through sieve of I.S. designation 16 mm Cu.Mt. 15.00 12.50 12.50 40.00 352.55 14102.00

ii 2.4.3 Screened through sieve of I.S. designation 4.75 mm Cu.Mt. 15.00 12.50 12.50 40.00 387.95 15518.00

Spreading of sludge, dump manure and/or good earth in required thickness as

3 2.8 per direction of officer-in-charge (cost of sludge, dump manure and/ or good Cu.Mt. 37.50 54.30 24.81 117.00 63.50 7430.00

earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or

directed by the Officer-in-charge

Grassing with selection No. 1 grass including watering and maintenance of the

lawn for 60 days or more till the grass forms a thick lawn, free from weeds and

fit for mowing including supplying good earth, if needed (the grass and earth

shall be paid for separately).

Digging holes in ordinary soil and refilling the same with the excavated earth

mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked

volume of earth after reduction by 20% : 1 part of stacked volume of manure

6 2.14 after reduction by 8%) flooding with water, dressing including removal of 0.00 0.00

rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge

or extra good earth if needed to be paid for separately) :

iii 2.14.3 Holes 60 cm dia, and 60 cm deep Each 15 10 7 32.00 48.3 1546.00

iv 2.14.4 Holes 45 cm dia, and 45 cm deep. Each 10 7 10 27.00 20.7 559.00

Providing Circular Cement Concrete pots of specified size, cast with cement

concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone

aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos

vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required

form work, finishing with cement punning on exposed surface, curing for

specified period and stacking in required rows & height, all complete as per

direction of Officer-in-charge.

Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall

thickness of 25.4 mm

Providing Square Cement Concrete pots of specified size, cast with cement

concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone

aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos

vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required

frame work, finishing with cement punning on exposed surface, curing for

specified period and stacking in required rows & height, all complete as per

direction of Officer-in-charge.

Top inner width 35 cm, outer bottom width 25 cm, total height 35 cm and wall

thickness 25.4 mm

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm

thickness of existing ground prepared with proper level and ramming with tools

wooden (Dhurmos) and than rolling the surface with light roller make the

surface smoothen and light waterning with sprinkler and maintenance for 30

days or more till the grass establish properly, as per direction of officer-in-

Supplying & Stacking of Selection No.1 doob grass turf at site fresh & free from

weeds having proper roots in green including loading, unloading, carriage and

all taxes paid etc.and as per direction of officer in charge.

Complete maintenance of the entire garden features having as per yard stick in

the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers

etc. including hoeing,weeding pruning replacement of plants, gap filling,

watering, mowing of lawn, grass cutting by lawn mover and brush cutter ,

removal of garden waste, applying insecticide, pesticide & fertilizers(whenever

11 2.40 required) top dressing of lawn with good earth and menure and maintenance of 0.00 0.00

other garden related works as directed by office-in-charge (Cost of Good Earth,

Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department &

lawn mover and brush cutter with fuel , other T & P material/articles shall be

provided by the contractor.)

i 2.40.5 Play grounds / Public parks (as per yard stick 1Mali =2.00Acre). Sq.Mt. 150.00 125.00 125.00 400.00 2.95 1180.00

Complete maintenance of shrubs (Out side garden features), jobs like making of

basin at regular interval i/c watering, weeding, pruning & application of fertilizer

12 2.43 etc, (excluding the cost of material which shall be supplied by the department) 90 75 50 215.00 46.10 9912.00

and as per direction of officer in charge.

Providing and applying anti termite treatment of infected trees i/c all

branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC)

13 2.55 concentration through power spray machine (@ 100 ml Chlorpyriphos per tree 75 60 35 170.00 72.3 12283.00

i/c cost of chemical) and as per direction of officer-in-charge.and as per

direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter

premise diluted in 499 liters water and applying solution @ 1.00 litre solution

14 2.56 per sqm lawn or bed area.(two application) i/c cost of chemical)and as per Sq.Mt. 37.50 31.25 31.25 100.00 9.20 920.00

direction of officer-in-charge.and as per direction of officer-in-charge.

15 4.0 Rose Plants 0.00 0.00

Providing and Displaying plants Budded Rose (H.T. variety) 3 to 4 healthy branch

30 cm and above ht. well developed with one and above flower plant in 20 cm

Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying plants Creeper Rose variety 3 to 4 healthy branch 60

ii 4.92 cm and above ht. well developed with one and above flowers in 25 cm Earthen Each 20 15 15 50.00 80.65 4033.00

Pot, as per direction of the officer-in-charge.

Providing and Displaying plants Standard Rose (H.T. variety) 3 to 4 healthy

branch 90 cm and above ht. well developed with one and above flowers in 25

cm Earthen Pot, as per direction of the officer-in-charge.

16 5.0 Ornamental Plants 0.00 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing and Displaying Acalypha plant Different colour well developed, fresh

& healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size of

Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge.

Providing and Displaying Acalypha red plant well developed with fresh & healthy

ii 5.3 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the Each 10 10 10 30.00 43.60 1308.00

officer-in-charge.

Providing and Displaying Ficus reginold piller type Topiary plant well developed

iii 5.26 with fresh & healthy 210 to 240 cm ht in 40 cm Cement Pot as per direction of Each 7 7 7 21.00 2615.70 54930.00

the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry

palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in

full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-

Providing and Displaying Ficus Long Island topiary plant well developed with

fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm

Cement Pot as per direction of the officer-in-charge.

17 6.0 Ground Covers Plants 0.00 0.00

Providing and Displaying of Clerodendron inerme plant of ht. 30 cm to 40 cm

i 6.7 multi branched in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the Each 10 10 10 30.00 21.25 638.00

officer-in-charge.

Providing and Displaying of Iresine herbstii plant, of height 20-30 cm., full of

ii 6.17 branches well developed in 20 cm size of Earthen Pot / Plastic Pot & as per Each 5 5 5 15.00 21.25 319.00

direction of the officer-in-charge..

Providing and stacking of Wedelia trilobata, full of leaves in 15 cm size of

Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

18 7.0 Tree Plants 0.00 0.00

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in

i 7.75 gunny bag of size 30 cm as per direction of the officer-in-charge. Each 10 10 10 30.00 106.35 3191.00

Supply and stacking of Washingtonia filifea palm plant stem ht. 120-135 cm with

ii 7.90 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as Each 5 5 5 15.00 691.15 10367.00

per direction of the officer-in-charge.

TOTAL (Carried Over to Summary of Civil Works) 0.00 458616.00 0.00

M 21.0 ALUMINIUM & STRUCTURAL GLAZING WORK 0.00

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/appropriate

Z sections and other sections of approved make conforming to IS: 733

and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or

with expansion hold fasteners including necessary filling up of gaps at

junctions, at top, bottom and sides with required PVC/neoprene felt etc.

1 21.1 Aluminium sections shall be smooth, rust free, straight, mitred and 0.00

jointed echanically wherever required including cleat angle, Aluminium

snap beading for glazing / paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the directions of Engineer-in-

charge. Glazing and paneling to be paid for separately) :

a) 21.1.1 For fixed portion. 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings wherever

required including the cost of EPDM rubber / neoprene gasket required

(Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Providing and fixing 12 mm thick prelaminated particle board flat

pressed three layer or graded wood particle board conforming to IS:

12823 Grade l Type ll, in panelling fixed in aluminum doors, windows

shutters and partition frames with C.P. brass / stainless steel screws etc.

complete as per architectural drawings and directions of engineerin-

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket etc.

3 21.3 complete as per the architectural drawings and the directions of 0.00 0.00

engineer-in-charge . (Cost of aluminium snap beading shall be paid in

With float glass panes of 5 mm thickness (weight not less than 12.50

Filling the gap in between aluminium frame and adjacent

RCC/Brickwork/ Stone Work by providing weather silicon sealant over

backer rod of approved quality as per architectural drawings and

direction of Engineer-in-charge

Providing and supplying aluminium extruded tubular and other aluminium

sections as per the architectural drawings and approved shop drawings , the

aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super

durable powder coating of 60-80 microns conforming to AAMA 2604 of required

colour and shade as approved by the Engineer-in-Charge. ( The item includes

cost of material such as cleats, sleeves, screws etc. necessary for fabrication of

extruded aluminium frame work. Nothing extra shall be paid on this account).

The weight of aluminium extruded section shall be taken for purpose of

Designing, fabricating, testing, protection, installing and fixing in position semi

(grid) unitized system of structural/ curtain wall glazing (with open joints) for

linear as well as curvilinear portions of the building for all heights and all levels,

a) Structural analysis & design and preparation of shop drawings for the

specified design loads conforming to IS 875 part III (the system must passed the

proof test at 1.5 times design wind pressure without any failure), including

functional design of the aluminum sections for fixing glazing panels of various

thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws,

toggles, nuts, bolts, clamps etc., structural and weather silicone sealants,

flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets

for water tightness, pressure equalization & drainage and protection against fire

hazard including:

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

b) Fabricating and supplying serrated M.S. hot dip galvanized / Aluminium alloy

of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate

3 Dimensional movement for achieving perfect verticality and fixing structural

glazing system rigidly to the RCC/ masonry/structural steel framework of

building structure using stainless steel anchor fasteners/ bolts, nylon separator

to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade

316, of the required capacity and in required numbers..

c) Providing and filling, two part pump filled, structural silicone sealant and one

part weather silicone sealant compatible with the structural silicone sealant of

required bite size in a clean and controlled factory / work shop environment ,

including double sided spacer tape, setting blocks and backer rod, all of 0.00 0.00

approved grade, brand and manufacture, as per the approved sealant design,

within and all around the perimeter for holding glass

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick

and of sizes, shapes and profiles, as required as per the site conditions, to seal

the gap between the building structure and all its interfaces with curtain glazing

to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain

glazing system to make it watertight, by incorporating principles of pressure

equalization, providing suitable gutter profiles at bottom (if required), making

necessary holes of required sizes and of required numbers etc. complete. This

item includes cost of all inputs of designing, labour for fabricating and

installation of aluminium grid, installation of glazed units, T&P, scaffolding and

other incidental charges including wastages etc., enabling temporary structures

and services, cranes or cradles etc. as described above and as specified. The

item includes the cost of getting all the structural and functional design

including shop drawings checked by a structural designer, dully approved by

Engineer-in-charge.

The item also includes the cost of all mock ups at site, cost of all samples of the

individual components for testing in an approved laboratory, field tests on the

assembled working structural glazing as specified, cleaning and protection till

the handing over of the building for occupation. In the end, the Contractor shall

provide a water tight structural glazing having all the performance 0.00 0.00

characteristics etc. all complete as required, as per the Architectural drawings,

as per item description, as specified, as per the approved shop drawings and as

directed by the Engineer in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes,

extruded aluminium section capping for fixing in the grooves of the curtain

glazing and vermin proof stainless steel wire mesh shall be paid for separately

under relevant items under this subhead. However, for the purpose of payment, 0.00 0.00

only the actual area of structural/ curtain wall glazing (including width of

grooves ) on the external face shall be measured in sqm. up to two decimal

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Providing, assembling and supplying vision glass panels (IGUs) comprising of

hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel

units of size and shape as required and specified, comprising of an outer heat

strengthened (as approved) glass 6mm thick, of approved colour and shade with

reflective soft coating on surface # 2 of approved colour and shade, an inner

heat strengthened (as approved) clear float glass 6mm thick, spacer tube 12mm

wide, desiccants, including primary seal and secondary seal (structural silicone

sealant) etc. all complete for the required performances, as per the Architectural

drawings, as per the approved shop drawings, as specified and as directed by

the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of

the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is

included in cost of item No.1.8.16 above). For payment, only the actual area of

glass on face # 1 of the glass panels (excluding the areas of the grooves and

weather silicone sealant) provided and fixed in position, shall be measured in

sqm. (To be fixed on extruded aluminium sections. and cost of aluminium

sections to be paid in relevant item)

(i) Coloured tinted float glass 6mm thick Heat Strengthened substrate with

reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened

clear Glass of approved make having properties as visible Light transmittance

(VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external

10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2

Extra for openable side / top hung vision glass panels (IGUs/laminated glass)

including providing and supplying at site all accessories and hardware for the

openable panels as specified and of the approved make such as heavy duty

stainless steel friction hinges, min 4 -point cremone locking sets with stainless

8 25.4 steel plates, handles, buffers etc. including necessary stainless steel screws/ Sqm 101.15 24.73 126.00 3671.50 3572.37 450119.00

fasteners, nuts, bolts, washers etc. all complete as per the Architectural

drawings, as per the approved shop drawings, as specified and as directed by

the Engineer in- Charge..

Providing and fixing 12 mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom

pivot & double acting hydraulic floor spring type fixing arrangement and making

necessary holes etc. for fixing required door fittings, all complete as per

direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid

Providing and fixing Pull Handle back to Back Approved makes of Fixing 25mm

10 MR-16 dia x300mm c/c, SS Matt with necessary screws etc. complete as per direction Each 72.00 2.00 3.15 77.00 0.00 2688.55 207018.00

of Engineer-in-Charge.

Providing and fixing Corner Patch Lock With Cylinder Approved makes, SS Matt

11 MR-17 with necessary screws etc. complete as per direction of Engineer-in-Charge. Each 36.00 1.00 4.00 41.00 0.00 4007.55 164310.00

Providing and fixing 12mm thk. Toughened float glass glazing cut and fixed in

openings of desired shape as per drawing with 3/4" beveling all around, fixed

with the help of SS patch fittings, with top and bottom 'C' channels, fixed firmly

12 MR-18 to the slab/ MS Structure ,as directed by Engineer in Charge. Area of openings to Sqm 149.02 10.00 2.00 161.00 0.00 5965.80 960494.00

be measured). Assume frameless glass. Rate of above item to include P/F of :

20x20mm "C" channel SS patch Fittings.

Aluminium Louver 0.00

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

Supply and installation of Exterior Aluminium Vertical Louvers ARF200 Vertical

Fin System, in different sizes as per drawing. Louvers to be made with

Aluminium Box Tube sections and covered with Solid Aluminium Sheet pre-

coated on a continuous reverse roller colour coating line with high durable paint

in approved colour. The top coated surface shall be pre coated. Post painting by

way of powder coating or spray coating is not allowed. Colour consistency with

pre coating is desired. Welding is not acceptable. Blades to be mechanically

secured to allow for replacement in case of damage. Fasteners to be hex head.

All the fasteners should be mechanically fastened. Louvers must be factory

fabricated and finished so that only assembly / installation will be done at the

TOTAL (Carried Over to Summary of Civil Works) 0.00 18059283.00 15223822.00

N 22.0 WATER PROOFING 0.00

Providing and laying water proofing treatment to vertical and horizontal

1 22.3 surfaces of depressed portions of W.C., kitchen and the like consisting of 0.00

(i) Ist course of applying cement slurry @ 4.4 Kg/Sqm mixed with water

proofing compound conforming to IS 2645 in recommended proportions

including rounding off junction of vertical and horizontal surface. (ii) IInd

course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed

with water proofing compound in recommended proportion including

rounding off junction of vertical and horizontal surface. (iii) IIIrd course sqm 365.97 490.95 497.91 1355.00 769.60 748.82 1014652.00

of applying blown or residual bitumen applied hot at 1.7 Kg. per Sqm of

area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of

PVC sheet should be 100 mm wide and pasted to each other with

bitumen @ 1.7 Kg/Sqm.)

Supplying and Stacking Filling sunken floor with over burnt jhama brick

2 16.3.4 aggregate 120mm to 40mm including compacting of materials complete Cum 128.09 171.83 174.27 474.00 798.10 776.55 368085.00

as specified and directed for all levels.

Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations: (a) Applying a

slurry coat of neat cement using 2.75 kg/sqm of cement admixed with

water proofing compound conforming to IS. 2645 and approved by

Engineer-in-charge over the RCC slab including adjoining walls upto 300

mm height including cleaning the surface before treatment. (b) Laying

brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm

3 22.7 size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed 0.00 0.00

with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5

(1 cement :5 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge to required

slope and treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs.

Academic, Boys Hostel, Girls Hostel,

Sl. No. DSR-2023 DESCRIPTION UNIT Total, Qty. RATE Final RATE DSR Amount NDSR Amount

Qty. Qty. Qty.

(c) After two days of proper curing applying a second coat of cement

slurry using 2.75 kg/ sqm of cement admixed with water proofing

compound conforming to IS : 2645 and approved by Engineerin- charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix

1:4 (1 cement :4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin- charge including

laying glass fibre cloth of approved quality in top layer of plaster and 0.00 0.00

finally finishing the surface with trowel with neat cement slurry and

making pattern of 300x300 mm square 3 mm deep. (e) The whole

terrace so finished shall be flooded with water for a minimum period of

two weeks for curing and for final test. All above operations to be done

in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as

TOTAL (Carried Over to Summary of Civil Works) 6463996.00 0.00

Total of DSR & NDSR 618672109.00

Project Name:- Construction of Rani Lakshmibai Central Agricultural

university at Jhansi, Uttar Pradesh.

Location:- Jhansi, Uttar Pradesh

S.No. Description DSR Amount NDSR Amount

1 Academic Block 0.00 54504807.00

2 Boys Hostel 0.00 25956952.00

3 Girls Hostel 0.00 10105496.00

PROJECT NAME:- CONSTRUCTION OF RANI LAKSHMIBAI CENTRAL AGRICULTURAL UNIVERSITY AT JHANSI, UTTAR PRADESH.

Ground First Second Third Fourth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Qty

Dimension: 3000mm (L) x 900mm(D) x 1050mm(H)

Supplying and placing in position of 360 degrees revolving medium back chair of size: 660mm (L) x 490mm(D) x 1100mm(H) as per

photograph. The breathable mesh back chair with cushioned fabric seat shall be ergonomically design with adjustable lumbar back support .

The chair shall be provisioned with adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust Movement). The

seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The seat to be made with 12 mm thick hot

pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black Five star chrome

base with hooded nylon castors..The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs

extension force.The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

Supplying and placing in position of 360 degrees revolving medium back chair of size: 660mm (L) x 490mm(D) x 1100mm(H) as per

photograph. The breathable mesh back chair with cushioned fabric seat shall be ergonomically design with adjustable lumbar back support .

The chair shall be provisioned with adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust Movement). The

seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The seat to be made with 12 mm thick hot

pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black Five star chrome

base with hooded nylon castors..The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs

extension force.The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

3 Sofa for Entrance lobby/ Student Common room/Staff Common room

3 seater Dimension(W)1650mm X (D)750mm X (H)710mm 8 0 0 6 6 20 nos 45,220 9,04,400

Supplying, and placing in position of sofa as per Image.A supple premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Sitting proudly on sleek steel legs the sofa exudes a sense of comfort that is perfect for any

space. Material & subtype:Premium Leatherette, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

Style:Modern, steam beech solid wood have used for framing construction of sofa .The seat cushion is made of multi layered foam of density

32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery

wrinke free & soft.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

3 Centre Table for Entrance lobby/ Student Common room/Staff Common room

Supplying, and placing in position of centre table as per Image. The centre table made of solid wood (steam beech) in pu matt polish.The

plain glass placed the top of the table in 8mm thk. The wood work below the glass provides the glass with a focal point and some support.

Add volumes of style to yourliving room with the centre table. Material & subtype: Solid Wood -Beech Wood( spc:steam beach), Colour &

Colour Family:Brown Dark Oak,Shape:Rectangular Legs/Base:Solid Wood, Finish:Glossy,Style:Contemporary. The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/

AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

4 Table for Break out area/ Student Lounge area

Supplying, and placing in position of table as per image/drawing. Table top made out of

25mm thk prelaminated particle board with 2mm thk pvc edge banding with ms powder coated

"C" shape legs of size 50 x 50mm. Comprising of metal powder coated cross connectors of size

40mm X 40mm. The working edges shall be provided with machine pressed 2mm thick PVC edging

using special hot melt glue at hot temperature.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT

Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under the

guidance of Engineer in charge.

5 Chair for Break out area /Student Lounge area 40 40 0 40 40 160 nos 9,240 14,78,400

Digitally signed by ANUJ

Ground First Second Third Fourth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Qty

Supplying, and placing in position of chair of size: (W585mm X (D)650mm X (H)735mm as per image.The comfortable cushioning

wrapped in premium fabric elevates your daily lounging up a notch. Adorned with contrasting black-finished metal legs.Material &

Subtype:Fabric - Velvet, Metal, Frame Material:Metal, Upholstery Material:Fabric - Velvet, Filling Material:Foam, Seat Material:Fabric -

Velvet, Leg Material:Metal, Seating Height:415mm. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT

Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under the

guidance of Engineer in charge.

6 Main Table for HOD Room

Main Table Dimesnion: (L)2300mm X (D) 900mm X (H)750mm

All over Side Runner Dimension: (L)1800mm X (D)450mm X (H)650mm

Supplying, and placing in position of a straight line table with wire manager as per photograph/drawing. The main desk of

size 2100mm (L) X 900mm (D) X 750mm (H) shall be made out of 42mm thick pre laminated particle board with the

approved shade. Table top supported with side panels and modesty panel. The side panels made out of 42mm thick pre

laminated Particle board & modesty panel made out of 36mm thk pre laminated Particle board of approved shade. All

working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of Pop-up cable manager box in the table .The Fixed Side Runner attached to the table of all over size 1800mm (L)

x450mm (D) x 650mm (H) has a provision for three drawer with locking facility , two openable shutterswith locking arrangement , open

storage with shelf & one open storage for cpu.The another side panel of table top having a provision of two attached drawer as per

photograph. The table top rest on SS studs for design purpose same as per image.The product should be from manufacturer(OEM) which

have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA

LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

7 Main Chair for HOD Room 0 1 0 0 0 1 nos 20,790 20,790

Supplying and placing in position similar to 360 degrees revolving high back chair . The chair of Size :- (W)590mm X

(D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour lumbar back design made of 12mm

thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The leatherette upholstery in the chair

has the look and feel of top grain leather. The chrome plated loop armrest with padded upholstery is provided for extra comfort. The chair

shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors .

Chair seat has foam of density 30-35 (+/-2kg /m3) Dimensions The backrest has a foam of 28kg/m3. The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/

AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

8 Visitor Chair for HOD Room 0 3 0 0 0 3 nos 19,460 58,380

Supplying and placing in position similar to 360 degrees revolving medium back chair . The Craze chair of Size :-(W)590mm X (D)505mm

X (H)1005mm - 1115mm. The chair shall be ergonomically design contour lumbar back design made of 12mm thick BWR plywood (IS Grade

- 303 for seat and back) upholstered with leatheritte and cut foam. The leatherette upholstery in the chair has the look and feel of top grain

leather. The chrome plated loop armrest with padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-

35 (+/-2kg /m3) The backrest has a foam of 28kg/m3. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT

Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under the

guidance of Engineer in charge.

9 Sofa for HOD Room

3 seater Dimension(W)1800mm X (D)710mm X (H)770mm 0 1 0 0 0 1 nos 62,160 62,160

Supplying and placing in position of exclusive premium leatherette with solid wood frame modernist classic design lounge seating sofa with

kiln-dried wood framing makes it warp and scratch resistant, comfortable seat depth & height designed. Combination construction

structure are made in moisture content shall be less than (10-12) %. Thickness of plywood used (mm) shall be 12 mm grade is 303 Indian

standard for commercial (common) and moisture proof plywood (tentative).under structure frame shall be constructed from 18 mm thick

kiln-dried German beech wood framing is

highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue, the frame shall be padded with high resilience

polyurethane foam having 28 +/- 5 density in seat it shall be stack foam of 50mm thick, 40mm thick back foam having 20 +/- 5 density

foam used, there shall be cushion arm 10mm thick provided padded with high resilience polyurethane foam having density 32 +/- 5.The

product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification /

GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the

approved make .The product should be as per above given specification under the guidance of Engineer in charge.

10 Centre table for HOD Room

Digitally signed by ANUJ

Ground First Second Third Fourth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Qty

Supplying, and placing in position of center table as per photograph. the Molly collection is destined to become a centerpiece of your

modern Indian homes. Perching on solid wood trestle legs, the veneer tabletop is tastefully adorned with brick pattern, crafted to perfection

by skilled Marquetry artisans.Tabletop crafted of premium engineered wood wrapped in Steam Beech veneer in Wenge finish.Veneer

features brick patterns, masterfully crafted by skilled

Marquetry artisans.Legs are crafted of kiln-dried solid wood for added durability.Material & Subtype Veneer,Solid Wood - Steam Beech

Wood, Table Top Thickness 36mm,Colour & Colour Family, Brown - Wenge.The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA

LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

11 Side table for HOD Room

Supplying and placing in position of Side table as per image.,the collection is destined to become a centerpiece of your modern Indian

homes. Perching on solid wood trestle legs, the veneer tabletop is tastefully adorned with a brick pattern, crafted to perfection by skilled

Marquetry artisan Material & Subtype:Veneer/Solid Wood - Steam Beech Wood,Leg Material:Solid Wood, Finish:Matte Colour & Colour

Family:Brown - Wenge. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

12 Main table for PA to HOD

Main Table Dimension : 1500mm(L) X 750mm(D) X 750mm(H)

Overall Side Unit Dimension : 1500mm(L) X 450mm(D) x 750mm(H)

Supplying, and placing in position of main Table as per drawing/image. Modular tables of size 1500mm(L) x 750mm(D) x 750mm(H). The

Table top are made out of 25mm thk prelam particle board with 2mm thk pvc edge banding & side panel & modesty panel are made up of

18mm thick pre-laminated particle board .The working edges shall be provided with machine pressed 2mm thick PVC edging using special

hot melt glue at hot temperature. The table have a provision of Side Storage of size 900mm L x 450mm D x 750mm Ht., Storage Top are

made out of 25mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated particle board . All

exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Side Storage having a

provision of 3 drawer unit of size: 400mm(L) x 450mm(D) x 675mm(H) attached to the side storage top with the help of shiny metal rods.

Pedestal Unit have a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of central Locking arrangement.The product should be from manufacturer(OEM) which have BIFMA

Complaint Certification / INDIAN DESIGN MARK Certification /GREEN PRO Certification/ AIOTA Certification.The product should be as

per above given specification under the guidance of Engineer in charge.

13 Main Chair for PA to HOD 0 1 0 0 0 1 nos 11,620 11,620

Supplying, and placing in position of Revolving High back chair. The chair of size 620mm (W) x 490mm (D) x 1240mm (H) . The chair with

adjustable arm rest of which seat shall be made up of 12mm thk hot pressed two pieces plywood upholstered with fabric in front and back in

ABS moulded with polyurethene foam. Provision of tilt tension adjustment,upright locking facility and full 360 degree swivel mechanism .

The base should be made of crome finished and fitted with 5 nos twin nylon castor. The pitch centre diameter of the base along with castors

should bot exceed 660mm, hydralic height adjustment stoke should be 60- 80mm and shall be operated at 30 kg. extension force. The Seat

& back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35

D. The backrest has a foam of 28D. .The product should be from the manufacture which have BIFMA Compliance Certification,

GREENGUARD/GREENPRO/FSC Certification,AIOTA Certification and from the approved make . The product should be as per above

given specification under the guidance of project architect &

Engineer in charge.

14 Visitor Chair for PA to HOD 0 2 0 0 0 2 nos 11,200 22,400

Supplying & placing in position of Medium back 360°-degree revolving chair as per image. all over size is: 600mm(l)x 660mm(d)x

1050mm(h), the chair made of full upholstery in black colour.it will comes in finish in contemporary style. arms: armrest is having two

adjustment heights (up & down). use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back). seat: 40 ± 2 mm thick

polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with

density 32 (±3) kg per cu meter for best quality cushioning in back. backrest support foam design based on symmetrical lumbar support

mechanism: self-weighted multi locking mechanism. only seat size is 480mm(l) x 500mm(d) & the back size is 460mm(l)x 510mm(h)seat

maximum height is 550mm & minimum height is 450mm & back height from floor maximum height is 1050mm & minimum height is

950mm. gas lift 100 mm telescopic haudraulic base: 650 mm chrome base with smooth castors.The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/

AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

15 Main table for Placement Office/Prof. Cabin-01/02

Main Table Dimesnion:1800mm(L)x 900mm(D)x 750mm(H)

Side runner Dimension:1200mm(l)x 400mm(d)x 750mm(h)

Digitally signed by ANUJ

Ground First Second Third Fourth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Qty

Supplying & placing in position of table structure of l shaped desk as per image. Primary work surface 50mm thick table top made of

prelaminated particle board work surface with classic wenge brown finish 2mm thick pvc edge banding made of same matte finish. side

panel is made of 50mm thick provision of side runner of size is 1200mm(l)x 400mm(d)x 750mm(h) ,(combination construction below table

top 1 key board tray in pvc with telescopic channel on right side is movable side runner having 1 openable door with 1 fixed shelve, 1 open

box with 1 fixed shelve upper shelve height is @ 320mm below shelve height is @324@ + 3 drawers (2 equal drawers + 1 filling drawer)per

drawer height is @ 184mm, filling drawer height is @ 303mm have central lock and handles with castors .mobile pedestal of size

400mm(l)x 530mm(d)x 671mm(h) ,per drawer height is @ 186mm, filling drawer height is @ 195mm having (2 equal drawers + 1 filling

drawer) in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm

along with facia of drawers.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/

GRIHA Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer

16 Main Chair for Placement Office/Prof. Cabin-01/02 2 4 0 0 0 6 nos 16,660 99,960

Supplying, and placing in position similar to high back 360° degree revolving chair all over size is : 630mm(l)x 675mm(d)x 1300mm(h) as

per image ,the chair made of full mesh in black colour .it will comes in matte finish in contemporary style .arms : armrest is having two

adjustment heights (up & down) .use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat).seat: 40 ± 2 mm thick

polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , back : frame of design shall be curved made of

two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support mechanism: self-weighted multi locking

mechanism .only seat size is 520mm(l)x 525mm(d)x 445-545mm(h) & the back size is 470mm(l)x 700mm(h) seat maximum height is

545mm & minimum height is 445mm & back height from floor maximum height is 1300mm & minimum height is 1200mm .gas lift 100

mm telescopic haudraulic base : 650 mm chrome base with smooth castors .The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA

LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

17 Visitor Chair for Placement Office/Prof. Cabin-01/02 4 8 0 0 0 12 nos 15,540 1,86,480

Supplying, and placing in position similar to medium back 360° degree revolving chair all over size is: 630mm (l) x 675mm (d) x 1115mm

(h) as per image. The chair made of full mesh in black colour .it will comes in matte finish in contemporary style .arms: armrest is having

two adjustment heights (up & down). Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat).seat: 40 ± 2 mm thick

polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , back : frame of design shall be curved made of

two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support mechanism : self-weighted multi locking

mechanism .only seat size is 520mm(l)x 525mm(d)x 445-545mm(h) & the back size is 470mm(l)x 590mm(h) ,seat maximum height is

545mm & minimum height is 445mm & back height from floor maximum height is 1115mm & minimum height is 1015mm .gas lift 100 mm

telescopic haudraulic base : 650 mm chrome base with smooth castors.The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1

Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

18 Chair for Placement Office 26 0 0 0 0 26 nos 8,190 2,12,940

Supplying and placing in position of tablet medium back chair as per Image. With a powder coated metal body design finished in matte

black gives this chair a no frills attitude as expected from this type of chair. The waterfall seat cushion and the backrest are upholstered in a

deep Black fabric for a complete black look. A tray is provided below the seat along with a movable tablet and an added side rest for support.

This chair is made for office and training purposes. Material & Subtype:Fabric, Colour & Colour Family:Black, Dimension(W)490mm X

(D)360mm X (H)820mm, Back Type:Low Back, Base:Four Leg Metal Frame, Base Type:Fixed, Finish:Matte. The Seat & back are made up

of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 30-32kg/m3. The backrest

has a foam of 28kg/m3.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

19 Sofa for Prof. Cabin-01/02

3 seater Dimension(W)1905mm X (D)890mm X (H)870mm 0 2 0 0 0 2 nos 48,160 96,320

Supplying, and placing in position of sofa as per Image .classic Contemporary design and slender curves. . The Sofa of stands Firm on

solid PVC legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides

for people to be seated comfortably. Finished in Leatherette , the sofa makes a fantastic first impression. The Cushioning is molded such

that it flows along the partition for a clean unified look. steam beech solid wood have used for framing construction of sofa The seat

cushion is made of multi layered foam of density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread

used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm.

The polyster polyfill keeps the upholstery wrinke free & soft. The product should be from manufacturer(OEM) which have BIFMA

Complaint Certification / INDIAN DESIGN MARK Certification /GREEN PRO Certification/ AIOTA Certification.The product should be as

per above given specification under the guidance of Engineer in charge.

20 Meeting table for office

Digitally signed by ANUJ

Ground First Second Third Fourth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Qty

Supplying and placing in position of meeting table as per image/drawing.The Table top are made out of 25mm thk prelam particle board

with 2mm thk pvc edge banding with ms powder coated "C" shape legs of size 50mm x 50mm Comprising of metal powder coated cross

connectors of size 40mm X 40mm. provision of metal wire raceway with 6 module flip top box.The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/

AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

21 Meeting Visitor Chair for office 10 10 12 10 10 52 nos 11,200 5,82,400

Medium back 360°-degree revolving chair as per image. all over size is: 600mm(l)x 660mm(d)x 1050mm(h), the chair made of full

upholstery in black colour.it will comes in finish in contemporary style. arms: armrest is having two adjustment heights (up & down). use of

ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back). seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3)

kg per cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best

quality cushioning in back. backrest support foam design based on symmetrical lumbar support mechanism: self-weighted multi locking

mechanism. only seat size is 480mm(l) x 500mm(d) & the back size is 460mm(l)x 510mm(h)seat maximum height is 550mm & minimum

height is 450mm & back height from floor maximum height is 1050mm & minimum height is 950mm. gas lift 100 mm telescopic

haudraulic base: 650 mm chrome base with smooth castors.The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1

Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

22 Table for Smart Class room/Examination Hall

Supplying, and placing in position of table as per image/Drawing. The top/work surface shall be 25

mm thk prelaminated particle board with 2mm thk pvc edge banding with 18mm thk prelaminated particle board modesty

panel with 2mm thk pvc edge bnading. Table top supported with MS powder coated square shape leg of 50mm x 50mm thk.

with horizontal connector of size 40mm x40mm thk. to support the tabletop The product should be from manufacturer(OEM)

which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA

Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make of

Godrej,HNI .The product should be as per above given specification under the guidance of Engineer in charge..

23 Chair for Smart Class room/Examination Hall 272 272 574 350 342 1810 nos 7,560 1,36,83,600

Supplying, and placing in position of chair as per image. The seat frame is constructed using sleek chrome with rich black leatherette

upholstery in stark contrast on the seat cushions. The tufted design on the seat and back adds to its style making this a perfect visitors

chair.Material & subtype: Premium Leatherette, Colour & Colour Family: Black, Dimension: (W)470mm X (D)400mm X (H)890mm, Back

Type:Low Back, Base:Four Leg Metal Frame, Base Type: Fixed, Maximum Seating Height: 19.29", Finish:Matte.The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/

AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

24 Faculty Table for Smart Class room

Supplying and placing in position of office desk office desk structure of rectangular shape as per image.primary work surface overall size is

1350mm(l)x 600mm(d)x 750mm(h) 25mm thick table top made of 25mm thick prelaminated particle board work surface with the exposed

edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue . Modesty panel made of

18mm thick, wire management hole with pvc grooment on table top. Construction right side of table top is based on a fixed pedestal 3

drawers & from left side of table top is based on 18mm thk engineered wood pvc edge banding pedestal back,top,bottom & drawers are made

of 18mm thick with 1 cpu trolley made in black metal powder coated. Fixed pedestal:l:410mm(l)x 580mm(d)x 750mm(h) ,in provided with

central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with facia of

drawers.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK

Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification

and from the approved make .The product should be as per above given specification under the guidance of Engineer in charge.

25 Faculty Chair for Smart Class room 2 2 0 3 4 11 nos 11,620 1,27,820

Digitally signed by ANUJ

Ground First Second Third Fourth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Qty

Supplying and placing in position of 360 degree Revolving medium back chair of Dimension (W)585mm X

(D)660mm X (H)1060mm as per image . Ergonomically designed, it features a breathable mesh backrest and adjustable lumbar support to

provide you all-day comfort. it offers Synchro Single Locking Mechanism along with a Tilt Tension Control. The adjustable armrest provide

deluxe comfort while the strong chrome base . The 55mm castor wheels and a 360- degree swivel provide swift yet stable movement.High-

quality fabric upholstery with high abrasion- resistance and superior tear strength & colourfastness,Premium high-density virgin foam for

comfortable seating,High stability chair with no-tip over, clearing drop test of 102kgs,Adjustable Lumbar Support for superior back

support,Pneumatic Height Lift with Class IV gas lift,Adjustable headrest with Synchro Single Locking and Tilt tension control for improved

mobility. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK

Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification

and from the approved make .The product should be as per above given specification under the guidance of Engineer in charge.

26 Counter for Lab-01/02

Providing and placing of all C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code

7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS

Code 513:1994. C-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm

thick. The C-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from-5mm to +15mm) to

correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted bacteria &

fungus.Horizontal Members should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x

30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. The hanging-type storage

cabinets can be suspended. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports

for drainage systems. It should be suitable for standing nominal heights of 900mm. The nominal table depths should be 750 mm for wall

side. All frame-work is should be pre-treated with superior pure epoxy powder coated finish. All cover panels should be made from CRCA

MS panels of minimum 0.8mm thickness with pure epoxy powder coating.Under bench cabinets are to be Pure epoxy powder coated with

thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip

as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to

the shutters. Hinges are to be of S-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each

shutter and cabinet.Shelf should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm.Worktop should be 20mm

(+/- 2mm) thick Mobil Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the

worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming

in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides. The backing material

used is a neoprene mat of 6 mm thickness.Laboratory Wall bench with granite top One no. under bench storage of 2 shutter 1 drawer

combination of 600mm Width. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/

GRIHA Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer

27 MATERIAL : MILD STEEL

COLOUR : MUNSHEL GREY & SAMOK GREY / FINISH : EPOXY POLYESTER,

WEIGTH OF PRODUCT : 111 KG APPROX,

CONSTRUCTION : CO2 WELDED.

* PROVIDING & SUPPLING PLACING POSITION OF MODULAR TWELVE DOORS SINGLE UNIT PERSONAL LOCKER LOCKING

SHALL HAVE STAPLE LOCK . MATERIAL SHALL BE CRCA 0.6 MM THICKNESS . CONSTRUCTION SHALL BE CO2 WELDED

CONSTRUCTION, SHELF SHALL BE UNIFORMLY DISTRIBUTED LOAD CAPACITY PER EACH SHELF LEVEL IS 30 KG

MAXIMUM.THESE COMPONENTS SHALL BE MADE OF CRCA ‘D’ GRADE HIGH YIELD STRENGTH AS PER IS:513 & IS:304 GRADE.

* FEATURES : INDEX HOLDER & AIR VENTILATION HOLE, FOLDABLE CAM LOCK WITH KEYS, CONCEALED METAL HINGES W/O

EXPOSED BRACKETS (BETTER SECURITY).

28 MATERIAL : MILD STEEL

COLOUR : SILVER / WEIGTH OF PRODUCT : 31 KG APPROX,

* SUPPLYING AND PLACING IN POSITION OF A MILD STEEL VISITOR BENCH OF SIZE IS 1820MM(L)X 690MM(D)X 790MM(H).

THE COMPLETE MILD STEEL BENCH HAS SEAT & BACK SINGLE SECTION. PER SEAT LENGTH IS @ 520 MM & SEATING HEIGHT

IS @ 430 MM FROM GROUND . OWING TO THE SMOOTH FINISH, DURABILITY AND TENSILE STRENGTH BEAM MADE OF MILD

STEEL 1.6MM THICK.SEAT IS MADE BY 1.2MM THICK MILD STEEL BORDER WITH CHROME PLATING FOR EVERY SEAT & BACK ;

MILD STEEL HANDLES CHROME PLATED & DIE PRESSED LEGS AT THE END OF CHAIRS.GROSS WEIGHT OF REGULAR 3-

SEATER WILL BE 31 KG.THE STEEL GRADE 202 HIGH YIELD STRENGTH AS PER IS:513 & IS:304 GRADE.

Total Amount Including GST@18% In Rs= 5,45,04,807

Total Amount Including GST@18% In Rs= 5,45,04,807

Digitally signed by ANUJ

PROJECT NAME:- CONSTRUCTION OF RANI LAKSHMIBAI CENTRAL AGRICULTURAL UNIVERSITY AT JHANSI, UTTAR PRADESH.

Ground First Second Third Fourth Fifth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Floor Qty

Boys Hostel- A Block

1 Sofa for Guest Lounge /Cutout area

Supplying and placing three-seater exclusive premium leatherette modernist classic design lounge seating sofa size is 1905mm(l)

x890mm(d)x 870mm(h) with kiln-dried wood framing makes it warp and scratch resistant, comfortable seat depth & height designed

keeping modern Indian lifestyle in mind, wrapped in buttery-soft premium leatherette, the panelled back and cushioned armrests

encourage lounging, designed with modernity & elegance, choose the option that suits your home. Combination construction structure

is made in moisture content shall be less than (10-12) %. thickness of plywood used (mm) shall be 12 mm grade is 303 Indian standard

for commercial (common) and moisture proof plywood (tentative). under structure frame shall be constructed from 18 mm thick kiln-

dried German beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue ,the

frame shall be padded with high resilience polyurethane foam having 28 +/- 5 density in seat it shall be stack foam of 50mm thik,40mm

thick back foam having 20 +/- 5 density foam used ,there shall be cushion arm 40mm thick provided padded with high resilience

polyurethane foam having density 20 +/- 5. the complete stack foam structure shall be covered with premium leatherette in black-eerie

black-coffee brown, brown-burnt umber colour, it complements the modish legs are made by round shape in pvc material. (seat: 510

mm(d) x 445mm(h) , arms height @ 620mm / back height @ 460mm ). The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

2 Centre table for Guest Lounge /Cutout area

Supplying, and placing in position of center table as per photograph. the Molly collection is destined to become a centerpiece of your

modern Indian homes. Perching on solid wood trestle legs, the veneer tabletop is tastefully adorned with brick pattern, crafted to

perfection by skilled Marquetry artisans.Tabletop crafted of premium engineered wood wrapped in Steam Beech veneer in Wenge

finish.Veneer features brick patterns, masterfully crafted by skilled Marquetry artisans.Legs are crafted of kiln-dried solid wood for

added durability.Material & Subtype Veneer,Solid Wood - Steam Beech Wood, Table Top Thickness 36mm,Colour & Colour Family,

Brown - Wenge.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

3 Main Table for Hostel Office/ Hostel Warden Office/Medical room

Supplying & placing in position of office desk structure of rectangular shape as per image .primary work surface overall size is

1400mm(l)x 700mm(d)x 750mm(h) 50mm thick table top made of prelaminated particle board work surface with the exposed edges

shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. modesty panel made of mm

thick. under structure made of 50mm thick with wire management hole with pvc grooment on table top. Provision of side unit of size is

600mm(l)x 400mm(d)x 600mm(h), (combination construction full table look like in h-shape from front side and table top is based on 2

+ 2 80mm thick boxes shape both the side made in same as prelaminated particle board table is made in a different style right side fixed

pedestal with 3 drawers + left side on filling storage shelve. Construction of 1 filing box fixed pedestal + 1 fixed pedestal with 3 equal

drawers in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18

mm along with facia of drawers.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

4 Main Chair for Hostel Office/ Hostel Warden Office/Medical room 4 0 0 0 0 0 4 nos 10,430 41,720

Supplying & placing in position of high back 360°-degree revolving chair all over size is: 660mm(l)x 440mm(d)x 1180mm(h)as per

image, The chair made of full fabric in red colour.it will come in matte finish in contemporary style. Arms: in pp connected to seat and

back. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back). seat: 40 ± 2 mm thick polyurethane foam with

density 32 (±3) kg per cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per

cu meter for best quality cushioning in back. backrest support foam design based on symmetrical lumbar support mechanism: centre tilt

mechanism. Only seat size is 650mm(l)x 440mm(d)x 525-440mm(h) & the back height is @ 670mm seat maximum height is 525mm &

minimum height is 440mm & back height from floor maximum height is 1180mm & minimum height is 1080mm gas lift 100 mm

telescopic haudraulic base: 650mm nylon base with smooth castors.The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA

LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above

given specification under the guidance of Engineer in charge.

5 Visitor Chair for Hostel Office/ Hostel Warden Office/Medical room 8 0 0 0 0 0 8 nos 9,030 72,240

Digitally signed by ANUJ

Ground First Second Third Fourth Fifth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Floor Qty

Supplying & placing in position of Fix cantilever chair all over size is: 480mm(l)x 440mm(d)x 820mm(h) as per image, the chair made of

full fabric in red colour.it will come in matte finish in contemporary style. arms: in pp connected to seat and back. use of ply: 12 mm

thick hot pressed bwr plywood (is grade - 303 for seat and back) . seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per

cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best

quality cushioning in back. backrest support foam design based on symmetrical lumbar support only seat size is 440mm(l)x 440mm(d)x

455 mm(h) & the back size is 4480mm(l)x 470mm(h) , seat height is @ 445mm & back height is @ 820mm.Fixed cantilever chair. base:

m.s powder coated tubular frame of cantilever type.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT

Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

6 Sofa for Hostel Warden Office

3 seater Dimension (L) 1650mm X (D) 750mm X (H) 710mm 1 0 0 0 0 0 1 nos 45,220 45,220

Supplying, and placing in position of sofa as per Image.A supple premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Sitting proudly on sleek steel legs the sofa exudes a sense of comfort that is perfect for any

space. Material & subtype:Premium Leatherette, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

Style:Modern, steam beech solid wood have used for framing construction of sofa .The seat cushion is made of multi layered foam of

density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting

stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the

upholstery wrinke free & soft.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/

GRIHA Certification and from the approved make .The product should be as per above given specification under the guidance of

Engineer in charge.

7 Centre Table for Guest Lounge / Hostel Warden Office/Entry area

Supplying, and placing in position of center table as per photograph. the Molly collection is destined to become a centerpiece of your

modern Indian homes. Perching on solid wood trestle legs, the veneer tabletop is tastefully adorned with brick pattern, crafted to

perfection by skilled Marquetry artisans.Tabletop crafted of premium engineered wood wrapped in Steam Beech veneer in Wenge

finish.Veneer features brick patterns, masterfully crafted by skilled Marquetry artisans.Legs are crafted of kiln-dried solid wood for

added durability.Material & Subtype Veneer,Solid Wood - Steam Beech Wood, Table Top Thickness 36mm,Colour & Colour Family,

Brown - Wenge.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

8 Patient stool for Medical room

Supplying, and placing in position of patient stool with 4 legs as per Image . Frame are made out of MS and Top are made out of

Stainless Steel finished with Powder Coated. Stainless steel round top & around ring with Height adjustable & revolving top.The product

should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN

PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

9 Examine bed for Medical room

Supplying, and placing in position of examine bed of size: 1800mm(L) X 600mm(D) x 810mm(H)as per Image . Frame work are made of

rectangular Stainless Steel withMounted on protective Stumps.Backrest and Knee rest movement on ratchet. Bed top is high-density

polyurethane foam, and covered with Washable faux leatherette : waterproof, flame retardant with provision of Detachable Cushioned

sponge mattress of 40mm thickness . Also having a provision of Adjustable Back and lockable in any lateral position. Maximum Weight

Capacity 200 kg.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN

MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA

Certification and from the approved make .The product should be as per above given specification under the guidance of Engineer in

10 Table for Dining area

Digitally signed by ANUJ

Ground First Second Third Fourth Fifth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Floor Qty

Supplying & placing in position of dining table as per photograph.The table top shall be made out of 25mm thick prelam particle board

with 2mm thk PVC edge banding. Table top shall be supported with Powder coated "C" shape metal legs of size 50mm x 50mm and metal

powder coated cross connectors of size 40mm x 40mm. The working edges shall be provided with machine pressed 2mm thick PVC

edging using special hot melt glue at hot temperature. The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1

Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

Supplying, and placing in position of cafe chair as per image. size: (l)381mm x (d)419mm x (h)839mm.The seat and

back in pvc moulded chair with ss 202 grade frame round pipe. The chair comes in various colours - green, black,

red,yellow, blue, brown, orange, white. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/

INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX

Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under the

guidance of Engineer in charge.

12 Single Bed for Rooms

Supplying and placing in position of single bed of overall size: 1950mm(L) x 950mm(W) x 825mm (H) as per

photograph/Drawing. The bed structure are made out of MS hollow box rectangular frame section of size 50mmx 25mm x

1.2mm thk, Cross connector/mattress plinth support ms frame of size: 25mm x 25mm x 1.2mm thk. The cross connector/

mattress plinth support will be 4nos. Material for Mattress Plinth Panel shall be 12mm thk balancing prelam mdf board,

Shape of Headboard shall be be Rectangular MS powder coated frame, Height of Headboard 363mm, Material of Headboard -

18mm thk prelam mdf board (OSL) with MS powder coated Frame. The headboard and tail board shall be covered with 18mm

thk prelam mdf board (OSL) with ms powder coated frame. The sides has to covered with 18mm thk prelam mdf board (OSL).

Complete metal structure shall be ms powder coated minimum 40 microns . The product should be from manufacturer(OEM)

which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA

Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The

product should be as per above given specification under the guidance of Engineer in charge.

13 Study Table for Rooms

Supplying and placing in position of study table with one drawer as per photograph/Drawing.The table top and Gable End are made out

of 25mm thick Pre- laminated Particle board with 2mm thk pvc edge banding. Modesty, Vertical, Drawer of size 400mm(L) X 450mm

(D) X 120mm(H) are made out of 18mm thick Pre-laminated Particle board. All exposed edges sealed with2mm thick PVC edge-banding.

The Table shall be provisioned with single drawer, handles & locking arrangement. The working edges shall be provided with machine

pressed 2mm thick PVC edging using special hot melt glue at hot temperature.The product should be from manufacturer(OEM) which

have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/

BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

Supplying, and placing in position of fix cantilever chair all over size is : 470mm(l)x 400mm(d)x 890mm(h) ,the chair made of

full leatherette in black colour it will comes in matte finish in contemporary style .arms : without arms. Use of ply: seat & back

plywood made of 12 mm hot pressed. Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best

quality cushioning in seat , back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality

cushioning in back . Backrest support foam design based on symmetrical lumbar support seat height is @ 490mm .base: four

chrome legs.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX

Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

15 Wardrobe for PG Rooms

Supplying, and placing in position of wardrobe as per photograph/drawing. Material of unit: body panels are made of 25mm thk

prelaminated particle board . All the exposed edges are edge banded with 2mm thk pvc edging. Door are made of 25mm thk

prelaminated particle board with all the exposed edges are edge banded with 2mm thk pvc edge banding. Drawer components are made

of 25mm thk prelaminated particle board All the exposed edges are edge banded with 2mm thk pvc edging. Body back & drawer bottom

are made of 8mm thk prelaminated particle board with 2mm thk pvc edge banding. Also having a Provision for two drawer & hanging

rod .Hardware: The high quality hardware used like roller slides , hinges, minifix, wooden dowels is of make hettich/ edco used for

middle door lock. . The product should be from

manufacturer(OEM) which have BIFMA Complaint Certification / INDIAN DESIGN MARK Certification /GREEN PRO

Certification/ AIOTA Certification.The product should be as per above given specification under the guidance of Engineer in charge.

Total Amount Including GST@18% In Rs= 2,59,56,952

Total Amount Including GST@18% In Rs= 2,59,56,952

Digitally signed by ANUJ

PROJECT NAME:- CONSTRUCTION OF RANI LAKSHMIBAI CENTRAL AGRICULTURAL UNIVERSITY AT JHANSI, UTTAR PRADESH.

Ground First Second Third Fourth Fifth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Floor Qty

1 Sofa for Reception area/Guest Lounge /Hostel Warden

Supplying, and placing in position of sofa as per Image.A supple premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Sitting proudly on sleek steel legs the sofa exudes a sense of comfort that is perfect for any

space. Material & subtype:Premium Leatherette, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

Style:Modern, Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat cushion is

made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread

used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer

of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft.The product should be from manufacturer(OEM)

which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA

Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The

product should be as per above given specification under the guidance of Engineer in charge.

2 Centre Table for Reception area

Supplying and placing in position of centre table as per photograph. The centre table made of solid wood (steam beech) in pu

matt polish.The plain glass placed the top of the table in 8mm thk. The turned wooden legs are sleek and sturdy providing the

table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of

style to yourliving room with the centre table. Material & subtype: Solid Wood -Beech Wood( spc:steam beach), Colour &

Colour Family:Brown - Dark Oak,Shape:Rectangular Legs/Base:Solid Wood, Finish:Glossy,Style:Contemporary.The product

should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification /

GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification

and from the approved make .The product should be as per above given specification under the guidance of Engineer in

3 Side Table for Reception area

Supplying, and placing in position of side table as per Image.The side table made of solid wood (steam beech) in pu matt

polish.The plain glass placed the top of the table in 8mm thk. The glass table top is made with strong glass and is inlaid onto

the solid wood frame. The designer wooden legs are turned for a sleeker look. The framed edges slope inwards to the table top

with defined edges. Material & Subtype:Solid Wood - Beech Wood ( spc:steam beach), Colour & Colour Family:Brown - Dark

Oak, Legs:Solid Wood, Finish:Glossy, Style:Contemporary. The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/

BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should

be as per above given specification under the guidance of Engineer in charge.

4 Table for Dining area

Supplying & placing in position of dining table as per photograph.The table top shall be made out of 25mm thick prelam particle board

with 2mm thk PVC edge banding. Table top shall be supported with Powder coated "C" shape metal legs of size 50mm x 50mm and metal

powder coated cross connectors of size 40mm x 40mm. The working edges shall be provided with machine pressed 2mm thick PVC

edging using special hot melt glue at hot temperature. The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1

Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

5 Chair for Dining area 60 0 0 0 0 0 60 nos 2,916 1,74,960

Supplying, and placing in position of cafe chair as per image. size: (l)381mm x (d)419mm x (h)839mm.The seat and

back in pvc moulded chair with ss 202 grade frame round pipe. The chair comes in various colours - green, black,

red,yellow, blue, brown, orange, white. The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/

INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX

Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under the

guidance of Engineer in charge.

6 Single Bed for Rooms

Digitally signed by ANUJ

Ground First Second Third Fourth Fifth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Floor Qty

Supplying and placing in position of single bed of overall size: 1950mm(L) x 950mm(W) x 825mm (H) as per

photograph/Drawing. The bed structure are made out of MS hollow box rectangular frame section of size 50mmx 25mm x

1.2mm thk, Cross connector/mattress plinth support ms frame of size: 25mm x 25mm x 1.2mm thk. The cross connector/

mattress plinth support will be 4nos. Material for Mattress Plinth Panel shall be 12mm thk balancing prelam mdf board,

Shape of Headboard shall be be Rectangular MS powder coated frame, Height of Headboard 363mm, Material of Headboard -

18mm thk prelam mdf board (OSL) with MS powder coated Frame. The headboard and tail board shall be covered with 18mm

thk prelam mdf board (OSL) with ms powder coated frame. The sides has to covered with 18mm thk prelam mdf board (OSL).

Complete metal structure shall be ms powder coated minimum 40 microns . The product should be from manufacturer(OEM)

which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA

Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The

product should be as per above given specification under the guidance of Engineer in charge.

7 Study Table for Rooms

Supplying and placing in position of study table with one drawer as per photograph/Drawing.The table top and Gable End are made out

of 25mm thick Pre- laminated Particle board with 2mm thk pvc edge banding. Modesty, Vertical, Drawer of size 400mm(L) X 450mm

(D) X 120mm(H) are made out of 18mm thick Pre-laminated Particle board. All exposed edges sealed with2mm thick PVC edge-banding.

The Table shall be provisioned with single drawer, handles & locking arrangement. The working edges shall be provided with machine

pressed 2mm thick PVC edging using special hot melt glue at hot temperature.The product should be from manufacturer(OEM) which

have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/

BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

Supplying, and placing in position of fix cantilever chair all over size is : 470mm(l)x 400mm(d)x 890mm(h) ,the chair made of

full leatherette in black colour it will comes in matte finish in contemporary style .arms : without arms. Use of ply: seat & back

plywood made of 12 mm hot pressed. Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best

quality cushioning in seat , back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality

cushioning in back . Backrest support foam design based on symmetrical lumbar support seat height is @ 490mm .base: four

chrome legs.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX

Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

9 Main Table for Hostel Warden Office

Supplying & placing in position of office desk structure of rectangular shape as per image .primary work surface overall size is

1400mm(l)x 700mm(d)x 750mm(h) 50mm thick table top made of prelaminated particle board work surface with the exposed edges

shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. modesty panel made of mm

thick. under structure made of 50mm thick with wire management hole with pvc grooment on table top. Provision of side unit of size is

600mm(l)x 400mm(d)x 600mm(h), (combination construction full table look like in h-shape from front side and table top is based on 2

+ 2 80mm thick boxes shape both the side made in same as prelaminated particle board table is made in a different style right side fixed

pedestal with 3 drawers + left side on filling storage shelve. Construction of 1 filing box fixed pedestal + 1 fixed pedestal with 3 equal

drawers in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18

mm along with facia of drawers.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product

should be as per above given specification under the guidance of Engineer in charge.

10 Main Chair for Hostel Warden Office 1 0 0 0 0 0 1 nos 10,430 10,430

Supplying & placing in position of high back 360°-degree revolving chair all over size is: 660mm(l)x 440mm(d)x 1180mm(h)as per

image, The chair made of full fabric in red colour.it will come in matte finish in contemporary style. Arms: in pp connected to seat and

back. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back). seat: 40 ± 2 mm thick polyurethane foam with

density 32 (±3) kg per cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per

cu meter for best quality cushioning in back. backrest support foam design based on symmetrical lumbar support mechanism: centre tilt

mechanism. Only seat size is 650mm(l)x 440mm(d)x 525-440mm(h) & the back height is @ 670mm seat maximum height is 525mm &

minimum height is 440mm & back height from floor maximum height is 1180mm & minimum height is 1080mm gas lift 100 mm

telescopic haudraulic base: 650mm nylon base with smooth castors.The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA

LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above

given specification under the guidance of Engineer in charge.

11 Visitor Chair for Hostel Warden Office 2 0 0 0 0 0 2 nos 9,030 18,060

Digitally signed by ANUJ

Ground First Second Third Fourth Fifth Total

S.No. Description of Item Unit Rate Amount Ref Image

Floor Floor Floor Floor Floor Floor Qty

Supplying & placing in position of Fix cantilever chair all over size is: 480mm(l)x 440mm(d)x 820mm(h) as per image, the chair made of

full fabric in red colour.it will come in matte finish in contemporary style. arms: in pp connected to seat and back. use of ply: 12 mm

thick hot pressed bwr plywood (is grade - 303 for seat and back) . seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per

cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best

quality cushioning in back. backrest support foam design based on symmetrical lumbar support only seat size is 440mm(l)x 440mm(d)x

455 mm(h) & the back size is 4480mm(l)x 470mm(h) , seat height is @ 445mm & back height is @ 820mm.Fixed cantilever chair. base:

m.s powder coated tubular frame of cantilever type.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT

Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/

SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under

the guidance of Engineer in charge.

12 Wardrobe for Rooms

Supplying, and placing in position of wardrobe as per photograph/drawing. Material of unit: body panels are made of 25mm thk

prelaminated particle board . All the exposed edges are edge banded with 2mm thk pvc edging. Door are made of 25mm thk

prelaminated particle board with all the exposed edges are edge banded with 2mm thk pvc edge banding. Drawer components are made

of 25mm thk prelaminated particle board All the exposed edges are edge banded with 2mm thk pvc edging. Body back & drawer bottom

are made of 8mm thk prelaminated particle board with 2mm thk pvc edge banding. Also having a Provision for two drawer & hanging

rod .Hardware: The high quality hardware used like roller slides , hinges, minifix, wooden dowels is of make hettich/ edco used for

middle door lock. . The product should be from

manufacturer(OEM) which have BIFMA Complaint Certification / INDIAN DESIGN MARK Certification /GREEN PRO

Certification/ AIOTA Certification.The product should be as per above given specification under the guidance of Engineer in charge.

Total Amount Including GST@18% In Rs= 1,01,05,496

Total Amount Including GST@18% In Rs= 1,01,05,496

Digitally signed by ANUJ

Project Name:- Construction of Rani Lakshmibai Central Agricultural university at Jhansi,

Detailed estimate of Internal & External Plumbing Services

S. No. Description

Amount (in Rs.)

1 SANITARY FIXTURES & FITTINGS 65,39,583 55,80,651

2 INTERNAL & EXTERNAL WATER SUPPLY 50,98,245 13,20,415

3 SOIL, WASTE, VENT PIPES, RAIN WATER PIPES & FITTINGS. 2,60,740 29,90,084

4 EXTERNAL SEWERAGE AND STORM WATER DRAINAGE 36,44,764 2,93,106

5 EXTERNAL WATER SUPPLY 3,09,405 22,440

6 RAIN WATER HARVESTING PIT 6,66,465

Applying Multiplying factor on DSR & NonDSR of @0.973 1,60,73,183 99,31,115

GRAND TOTAL (DSR +NSR) 2,60,04,298

GRAND TOTAL (DSR +NSR) 2,60,04,298

Digitally signed by ANUJ

Project Name:- Construction of Rani Lakshmibai Central Agricultural university at Jhansi, Uttar Pradesh.

Schedule Of Quantity

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

1.0 SANITARY FIXTURES & FITTINGS

Providing and fixing white vitreous china extended wall

mounting water closet of size 780x370x690mm of approved

shape including providing and fixing white vitreous china

1.1 17.78 cistern with dual flushing fitting,of flushing capacity 3 litre/6 Each 86 59 49 194 14999.15 2909835.1

litre( adjustable to 4 litre/8 litres),including seat cover and

cistern fittings,nuts,bolts and gasket etc. complete.

Providing and fixing wash basin with C.I. brackets, 15 mm

dia CP Brass single hole basin mixer of approved quality

and make, including painting of fittings and brackets, cutting

and making good the walls wherever required:-

a) White Vitreous China Wash basin size 630x450 mm with

a 15 mm CP Brass single hole basin mixer

Providing and fixing kitchen sink with C.I. brackets, C.P.

brass chain with rubber plug, 40 mm C.P. brass waste

1.3 17.9 complete, including painting the fittings and brackets,

cutting and making good the walls wherever required:

White glazed fire clay kitchen sink of size 600x450x 250

Supply, Receiving, Storing & Fixing of CP brass wall

mounted sink mixer with C.P. wall flange, swinging spout

complete as required with flow rate of 6.0 LPM complying to

Green Building requirements.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible

tube upto 1 metre long with S.S. triangular plate to

1.5 17.16A Eureopean type W.C. of quality and make as approved by Each 86 59 49 194 349.15 67735.1

Engineer - in - charge.

Providing and fixing CP Brass 32mm size bottle trap of

1.6 17.22A approved quality & make and as per the direction of Each 86 59 75 220 1034.8 227656

engineer in charge.

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Providing and fixing C.P. brass long nose bib cock of

1.7 18.50 approved quality conforming to IS standards and weighing

not less than 810 gms

1.8 17.34 Providing and fixing toilet paper holder

Supply, Receiving, Storing & Fixing of C.P. brass twin

1.9 MR-2 coat hook with PVC rawl plug & C.P. brass screw complete Each 86 59 75 220 740 162800

as required. Make :

Providing and fixing C.P. brass angle valve for basin mixer

and geyser points of approved quality conforming to

Providing and fixing unplasticised P.V.C. connection pipe

with PTMT Nuts, collar and bush of approved quality and

18.74.2 15 mm nominal bore with 45 cm length Each 268 277 260 805 121.9 98129.5

Providing and fixing Chromium Plated towel ring

Rectangular shape with concealed fittings arrangement of

1.12 MR-3 approved quality and colour, of approved brand & Each 86 59 75 220 1365 300300

manufacture complete as per direction of Engineer in

Providing and fixing of C. P. brass towel rail 600 x 20 mm

size complete with C.P. brass brackets.

Providing and fixing Cp bras liquid soap container 109 mm

wide, 125 mm high and 112 mm distance from wall of

1.14 MR-5 standard shape with bracket of the same materials with snap Each 86 59 75 220 1489 327580

fittings of approved quality and colour, weighing not less

Providing and fixing white vitreous china battery based

infrared sensor operated urinal of approx. size 610 x 390 x

370 mm having pre & post flushing with water (250 ml &

500 ml consumption), having water inlet from back side,

including fixing to wall with suitable brackets all as per

manufacturers specification and direction of Engineer-in-

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Providing and fixing 75 mm high, 50 mm deep and 18 mm

thick stone slab table rubbed, edges rounded and polished,

fixed in urinal partitions by cutting a chase of appropriate

width with chase cutter and embedding the stone in the

chase with epoxy grout or with cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 6 mm

nominal size) as per direction of Engineer-in-charge and

finished smooth.

8.10.2 Granite Stone of approved shade Sqm 55 47 102 4051.85 413288.7

Supply and fixing of water cooler fully stainless steel of 60

litres cooling capacity and 120 litres storage capacity to be

1.17 MR 6 operated on single phase supply with ISI mark. Each Cooler Each 10 12 7 29 77851 2257679

shall be provide with 4 Nos pessmatic tap for Drinking

Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm

thick hard board ground fixed to wooden cleats with C.P.

brass screws and washers complete.

Providing and fixing P.V.C. waste pipe for sink or wash

basin including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

Providing and fixing C.P. brass long body bib cock of

1.2 18.51 approved quality conforming to IS standards and weighing

not less than 690 gms.

Providing and Fixing 600 mm long Hand rail (Grab bar)

for Toilets with Stainless Steel Screws on wooden cleats /

expandable fastners complete as per instructions of the

engineer-in-charge

Providing and fixing low flow type two way bib tap as per

1.22 MR-8 approved make complete in all respect as per engineer in the Each 86 59 49 194 2184 423696

Providing and fixing of recessed type soap tray complete,

including cutting and making good the walls where required.

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Providing and Fixing Electric Hot Water Geyser of Stainless

Steel Material Grade 316 with Inlet and Outlet Connection

with 15 mm dia Angle Valve and Geyser (25 LTR)shall be

equipped with inbuilt non return valve and insulation on

1.24 MR-10 Each

inner and outer surfaces for prevention of heat losses 2 nos

CP round wall flange and CP Brass Screws and Rawl plugs

all other required accessories Complete in all respect as per

direction of Engineer - in - charge .

10.1 Electric Geyser 15 Litre Capacity Each 12300

10.2 Electric Geyser 25 Litre Capacity Each 44 40 84 21827 1833468

10.3 Electric Geyser 3 Litre instant capacity Each 4370

TOTAL CARRIED OVER TO SUMMARY 6539582.65 5580651

2 INTERNAL & EXTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold water

supply, including all CPVC plain & brass threaded fittings,

i/c fixing the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one step CPVC

solvent cement and the cost of cutting chases and making

good the same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and making good

2.1.4 18.8.4 32 mm nominal bore Metre 739.3

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold water

supply, including all CPVC plain & brass threaded fittings,

2.2 18.7 including fixing the pipe with clamps at 1.00 m spacing.

This includes jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints complete as per

direction of Engineer in Charge.

Internal work - Exposed on wall

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

g) Derived 65mm nominal bore Mtr. 63.25 63.25 63.25 189.75 1156 219351

i) Derived 100mm nominal bore Mtr. 46 46 46 138 2045 282210

Providing and fixing gun metal gate valve with C.I. wheel

of approved quality (screwed end) :

Providing and fixing ball valve (brass) of approved quality,

High or low pressure, with plastic floats complete :

18.18.1 15 mm nominal bore Each 8 8 406.86 3254.88

Derrived 32 mm nominal bore Each 16 24 24 64 2347 150208

Supplying, fixing, testing and commissioning of butterfly

valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required

Providing and fixing motorized valve with sensor of

approved quality, to complete the work.

a) 40 mm dia ( Flushing Riser) Each 1 2 2 5 27977 139885

b) 50 mm dia ( Domestic Riser) Each 1 2 2 5 28593 142965

Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, IS : 12701 marked, with

2.7 18.48 cover and suitable locking arrangement and making Each 58000 50000 35000 143000 11 1573000

necessary holes for inlet, outlet and overflow pipes but

without fittings and the base support for tank.

TOTAL CARRIED OVER TO SUMMARY 5098244.668 1320415.25

SOIL, WASTE, VENT PIPES, RAIN WATER PIPES &

Providing and fixing soil, waste and vent pipes

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Supplying, Installation, Testing and Commissioning of

uPVC pipes type -B conforming to IS 13592 (1992) for

soil, waste and vent pipes including all fittings rubber ring

type (plain or with access door) e.g. bends, junctions, cowls,

offsets, access pieces, jointing with rubber ring joints with

lubricant etc. fixed with clamps to walls with cement

concrete 1:2:4 blocks complete in all respects. (For Soil &

c) 160 OD mm Metre 2063

Providing, laying, Jointing, Testing and commissioning of

uPVC pressure pipes of 6Kg/Sqcm pressure rating class 5

(IS : 4985-2000) including fittings, tees, bends, clamps,

coupling and adaptors supports, and jointing with solvent

joint, testing and necessary earth work in excavation,

backfilling, disposal of surplus earth with a lead upto 50m

complete, compaction and consolidation Including laying

cement concrete 1:2:4 alround UPVC pipe including bed

concrete and thrust blocks at bends as per standard design

(For Soil & Waste Pipe)

Supplying, Installation, Testing and Commissioning of

uPVC, P or S trap of self cleansing design with / without

3.3 MR-14 vent. arm Setting in cement concrete 1:2:4 mix complete

including cost of cutting & making good the Wall / Floors

wherever required.

Providing and fixing floor drain with jali size 110X50 size

3.4 MR-15 inlet and outlet including cutting and making good the walls

and floors wherever required complete in all respects.

Providing and fixing 125 mm dia, 3 mm thick Stainless

steel grating with frame for floor traps or drains of required

pattern including cutting and making good the floors

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Providing and fixing cast brass Cleanout plug with suitable

insert keys for opening in brass cap, male threaded

joint/reducer with G.I. socket caulked to Pipe/fittings of CI

pipe including cost of lead joints etc. complete in all respect.

Making khurras 45x45 cm with average minimum thickness

of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over P.V.C.

3.7 12.22 sheet 1 m x1 m x 400 micron, finished with 12 mm cement each 10 10 8 28 298.25 8351

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the

outlet complete.450 X 450mm -

Providing and fixing on wall face unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion, (i) Single socketed pipes.

12.41.1 75 mm diameter Metre 248.8

Derived 160 mm diameter (with all fittings) Metre 1367

Providing and fixing to the inlet mouth of rain water pipe

3.9 12.44 cast iron grating 15 cm diameter and weighing not less than Each 10 10 8 28 54.7 1531.6

TOTAL CARRIED OVER TO SUMMARY 260740.38 2990083.825

EXTERNAL SEWERAGE AND STORM WATER

Excavating trenches of required width for pipes, cables, etc

including excavation for sockets, and dressing of sides,

ramming of bottoms, depth upto 1.5 m, including getting out

the excavated soil, and then returning the soil as required, in

4.1 2.10.1 layers not exceeding 20 cm in depth, including consolidating

each deposited layer by ramming, watering, etc. and

disposing of surplus excavated soil as directed, within a lead

All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Supplying and laying of following size DWC SN8 pipe ISI

marked along with all accessories like socket, bend, couplers

etc. conforming to IS 16098, Part II complete with fitting

4.2 MR-18 and cutting,jointing etc.direct in ground (75 cm below

ground level) including excavation and refilling the trench

but excluding sand cushioning and protective covering etc.,

complete as required.

Providing and laying cement concrete 1:5:10 (1 cement : 5

coarse sand : 10 graded stone aggregate 40 mm nominal

size) all-round DWC pipes including bed concrete as per

standard design :

Derrived 300 mm dia. DWC & RCC Pipe Metre

Derrived 450 mm dia. DWC & RCC Pipe Metre

Providing and laying non-pressure NP2 class (light duty)

4.2 19.6 pipes with collars jointed with stiff mixture of cement mortar

in the proportion of 1:2 (1 cement : 2 fine sand) including

testing of joints etc. complete :

Constructing brick masonry manhole in cement mortar 1:4

( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3

mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone

aggregate 20mm nominal size), foundation concrete 1:4:8

mix (1 cement : 4coarse sand (zone-III) : 8 graded stone

aggregate 40 mm nominalsize), inside plastering 12 mm

thick with cement mortar 1:3 (1 cement: 3 coarse sand)

finished with floating coat of neat cement andmaking

channels in cement concrete 1:2:4 (1 cement : 2 coarse sand

: 4 graded stone aggregate 20 mm nominal size) finished

with a floating coat of neat cement complete as per standard

Inside size 90x80 cm and 45 cm deep including C.I. cover

with frame (light duty) 455x610 mm internal dimensions,

total weight of cover and frame to be not less than 38 kg

(weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Inside size 120x90 cm and 90 cm deep including C.I. cover

with frame (medium duty) 500 mm internal diameter, total

weight of cover and frame to be not less than 116 kg (weight

of cover 58 kg and weight of frame 58 kg) : 19.7.2.1 With

common burnt clay F.P.S. (non modular) bricks of class

designation 7.5

4.5.3 19.8 Extra for depth for manholes :

19.8.1 Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Providing and fixing square-mouth S.W. gully trap class SP-

1 complete with C.I. grating brick masonry chamber with

4.6 19.4 water tight C.I. cover with frame of 300 x300 mm size

(inside) the weight of cover to be not less than 4.50 kg and

frame to be not less than 2.70 kg as per standard design :

19.4.2 150 x 100mm size P-type

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Constructing brick masonry road gully chamber

50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4

coarse sand) including 500x450mm precast RCC horizontal

grating with frame complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Constructing brick masonry road gully chamber

50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4

coarse sand) including 500x450mm precast RCC horizontal

grating with frame complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Providing orange colour safety foot rest of minimum 6 mm

thick plastic encapsulated as per IS : 10910 on 12mm dia

steel bar conforming to IS : 1786 having minimum cross

section as 23 mmx25mm and over all minimum length 263

mm and width as 165mm with minimum 112 mm space

between protruded legs having 2 mm tread on top surface by

ribbing or chequering besides necessary and adequate

4.1 19.16 anchoring projections on tail length on 138 mm as per Each

standard drawing and suitable to with stand the bend test

and chemical resistance test as per specifications and having

manufacture's permanent identification mark to be visible

even after fixing, including fixing in manholes with

30x20x15 cm cement concrete block 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal size)

complete as per design.

Making connection of drain or sewer line with existing

including breaking into and making good the walls, floors

with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) cement

plastered on both sides with cement mortar 1:3 (1 cement : 3

coarse sand), finished with a floating coat of neat cement

and making necessary channels for the drain etc. complete :

19.21.2 For pipes 250 to 300 mm diameter Each 10 10 10 30 922.4 27672

19.21.3 For pipes 350 to 450 mm diameter Each 10 10 10 30 1328.45 39853.5

TOTAL CARRIED TO SUMMARY 3644764 293106

5 EXTERNAL WATER SUPPLY

Providing and fixing G.I. pipes complete with G.I. fittings

including trenching and refilling etc.

18.12.2 20 mm dia nominal bore Metre 368.6

18.12.3 25 mm dia nominal bore Metre 467.75

18.12.4 32 mm dia nominal bore Metre 540.3

18.12.5 40 mm dia nominal bore Metre 617.05

18.12.6 50 mm dia nominal bore Metre 762.15

18.12.7 65 mm dia nominal bore Metre 20 20 20 60 896.6 53796

18.12.8 80 mm dia nominal bore Metre 30 30 30 90 1041.7 93753

NDSR 100 mm dia nominal bore Metre

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Providing and fixing in position garden hydrant hose outlet

consisting of 25mm ball valve full bore type with lever and

5.2 MR -19 female screwed ends, tested to 20 Kg/cm2 of approved Each 5 5 5 15 1496 22440

quality, including G.I. elbow, G.I. threaded hose receiver etc.

Providing and fixing enclosed type water meter (bulk type)

conforming to IS : 2373 and tested by Municipal Board

complete with bolts, nuts, rubber insertions etc. (The tail

pieces if required will be paid separately) :

Constructing masonry Chamber 30x30x50 cm inside, in

brick work in cement mortar 1:4 (1 cement :4 coarse sand)

for stop cock, with C. I. surface box 100x100 x75 mm

(inside) with hinged cover fixed in cement concrete slab

1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

5.4 18.32 aggregate 20 mm nominal size), i/c necessary excavation,

foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10

graded stone aggregate 40mm nominal size ) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

12mm thick, finished with a floating coat of neat cement

complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of

class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in

brick work in cement mortar 1:4 (1 cement : 4 coarse sand)

for sluice valve, with C.I. surface box 100mm top diameter,

160 mm bottom diameter and 180 mm deep ( inside) with

chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size ) , i/c

necessary excavation, foundation concrete 1:5:10 (1 cement

: 5 fine sand : 10 graded stone aggregate 40 mm nominal

size) and inside plastering with cement mortar 1:3 (1 cement

: 3 coarse sand) 12 mm thick, finished with a floating coat of

complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of

class designation 7.5

Digitally signed by ANUJ

ACADEMIC BOYS GIRLS TOTAL DSR Rate DSR Amount (in MR Rate MR Amount

S. No. DSR 2023 Description Unit

BUILDING HOSTEL HOSTEL QUANTITY (in Rs.) Rs.) (in Rs.) (in Rs.)

Constructing masonry Chamber 60x45x50 cm inside, in

brick work in cement mortar 1:4 (1 cement : 4 coarse sand)

for water meter complete with C.I. double flap surface box

400x200x200 mm (inside) with locking arrangement and

RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size) , i/c necessary

excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine

sand:10 graded stone aggregate 40 mm nominal size) and

inside plastering with cement mortar 1:3 (1 cement : 3 coarse

sand) 12 mm thick, finished with a floating coat of neat

cement complete as

per standard design :

With common burnt clay F.P.S.(non modular) bricks of

class designation 7.5

Painting G.I. pipes and fittings with two coats of anti-

5.7 18.40 corrosive

bitumastic paint of approved quality :

18.40.2 20 mm dia nominal bore Metre 14.45

18.40.3 25 mm dia nominal bore Metre 18.35

18.40.4 32 mm dia nominal bore Metre 22.2

18.40.5 40 mm dia nominal bore Metre 25.25

18.40.6 50 mm dia nominal bore Metre 30.5

18.40.7 65 mm dia nominal bore Metre 20 20 20 60 37.85 2271

18.40.8 80 mm dia nominal bore Metre 30 30 30 90 37.85 3406.5

NDSR 100 mm dia nominal bore Metre

Providing and filling sand of grading zone V or coarser

grade, allround the G.I. pipes in external work :

18.41.2 20 mm dia nominal bore Metre 156.55

18.41.3 25 mm dia nominal bore Metre 160.7

18.41.4 32 mm dia nominal bore Metre 164.9

18.41.5 40 mm dia nominal bore Metre 167

18.41.6 50 mm dia nominal bore Metre 173.25

18.41.7 65 mm dia nominal bore Metre 20 20 20 60 273.45 16407

18.41.8 80 mm dia nominal bore Metre 30 30 30 90 281.8 25362

18.41.9 100 mm dia nominal bore Metre 298.5

Providing and fixing G.I. Union in G.I. pipe including

5.9 18.46 cutting and threading the pipe and making long screws etc.

complete (New work) :