CA No GE/H-22/2020-21 Repair Maintenance of various type of Pump Motor and other allied work for Water Supply Distribution System at AHRR under GE E AND M RR Hospital Delhi Cantt 10

Amount

Taking up centrifugal pump along with motor of capacity 30 HP after disconnecting all electrical connections and transporting to local workshop for repair & Refixing the same after testing & commosioning of motor . ( Make of Pump for repair: Kirloskar , Location : Pump House No 2,Monkey Pump House ) Notes for Srl Item No 1,11,21,28,38,45,53,62 and 71 1. M&L for Dismantling rewinding etc shall be measured and paid seperately . 2.Unserviceable parts to be replaced shall be measured and paid as supply only under respective item of this schedule. However taking down old unserviceble part and fixing only of new part are also included the quoted rates. 3. The repair work shall be carried out best locally available workshop and necessary invoice /purchase voucher for repair work shall be obtained from the workshop. 4.Spare parts shall be of replaced with approved make as specified and necessaary purchase voucher shall be produce by the contractor while claiming the payment.

Dismantling, Over hauling cleaning ,of impellers strainers Rewinding of motor 30 HP complete with equivalent gauge of copper winding wire, paper & sleeve, wooden stick, 'O' ring set replacement. Make of copper wire :Devidayal/ Atlas/Milan/HTP/IMIDE

supply only ball bearing 6309

supply only ball bearing 6312

supply only ci gland for 30 Hp Pump

Supply only SS shaft sleeves in 30 HP pump with complete nut, bolt & stufs, nut & flanged, upper & lower, studs & nuts complete all as specified

Supply only key coupling for 30 Hp pump

Supply only bearing housing for 30 HP pump

supply only lock washer for support foot for 30 HP pump

Supply only bearing cover DE suitable for 30 HP pump

Taking up centrifugal pump along with motor of capacity 25 HP after disconnecting all electrical connections and transporting to local workshop for repair & Refixing the same after testing & commosioning of motor . (Make of Pump for repair: Kirloskar, Location : Pump House no 1, 2 and new pump)

Dismantling, Over hauling cleaning ,of impellers strainers Rewinding of motor 25 HP of any make complete with equivilient gauge of copper winding wire, paper & sleeve, wooden stick, 'O' ring set replacement.(Make of copper wire :Devidayal/ Atlas/Milan/HTP/IMIDE)

Supply only ball bearing 6307

Supply only ball bearing 6308

Supply only Shaft SS 410 for 25 HP

Supply only CI gland for 25 HP

Supply only inter stage ring 25 HP

supply only Drive end Bearing housing CI

Supply only CI centre ring for 25 HP

Supply only Air release valve of size 20 mm for 25 HP

Taking up centrifugal pump along with motor of capacity 15 HP after disconnecting all electrical connections and transporting to local workshop for repair & Refixing the same after testing & commosioning of motor . (Make of Pump for repair: Kirloskar , Location : Map)

Dismantling, Over hauling cleaning ,of impellers strainers Rewinding of motor 15 HP of any make complete with equivilient gauge of copper winding wire & insulating materials i.e. PVC sleeves insulation papers wooden stick 'O' ring complete. (Make of copper wire :Devidayal/ Atlas/Milan/HTP/IMIDE)

S&F in replacement of ss coupling for 15 hp monoblock pump set

Supply only in replacement of connection pieces suitable for 15 HP pump

Supply only in replacement of rotor guard for 15 HP

Supply only replacement of SS rotar sleeves for 15 HP

Supply only in replacement of sealing ring dor 15 HP

Taking up monoblock pumpset of capacity 10 HP after disconnecting all electrical connections and transporting to local workshop for repair & Refixing the same after testing & commosioning of motor . (Make of Pump for repair: Kirloskar , Location : J Block and MT)

Dismantling, Over hauling cleaning ,of impellers strainers Rewinding of motor 10 HP of any make complete with equivilient gauge of copper winding wire & insulating materials i.e. PVC sleeves insulation papers wooden stick 'O' ring complete. (Make of copper wire :Devidayal/ Atlas/Milan/HTP/IMIDE)

Supply only in replacement of SS coupling up to 10 HP monoblock pump set complete all as specified and as directed

Supply only in replacement of connection pieces suitable for 10 HP pump

Supply only in replacement of CI upper & lower housing for 10 HP

Supply only in replacement of CI motor base for10 HP

Supply only in replacement of revolving disc for capacity10 HP

Supply only in replacement of rotor guard for 10 HP

Supply only in replacement of SS rotor sleeves for 10 HP

Supply only in replacement of sealing ring for 10 HP

Taking up monoblock pumpset of capacity 7.5 HP after disconnecting all electrical connections and transporting to local workshop for repair & Refixing the same after testing & commosioning of motor . Make of Pump for repair: Kirloskar , Location : Laundary and Basemant)

Dismantling, Over hauling cleaning ,of impellers strainers Rewinding of motor 7.5 HP of any make complete with equivilient gauge of copper winding wire & insulating materials i.e. PVC sleeves insulation papers wooden stick 'O' ring complete. (Make of copper wire :Devidayal/ Atlas/Milan/HTP/IMIDE)

S&F in replacement of ss coupling for 7.5 hp monoblock pump set

Supply only in replacement of connection pieces suitable for 7.5 HP pump

Supply only in replacement of rotor guard for 7.5 HP

Supply only replacement of SS rotar sleeves for 7.5 HP

Supply only in replacement of sealing ring dor 7.5 HP

Taking up monoblock pumpset of capacity 5 HP after disconnecting all electrical connections and transporting to local workshop for repair & Refixing the same after testing & commosioning of motor . (Make of Pump for reapir: Kirloskar , Location : Basemant )

Dismantling, Over hauling cleaning ,of impellers strainers Rewinding of motor 5 HP of any make complete with equivilient gauge of copper winding wire & insulating materials i.e. PVC sleeves insulation papers wooden stick 'O' ring complete. (Make of copper wire :Devidayal/ Atlas/Milan/HTP/IMIDE)

S&F in replacement of ss coupling for 5 hp monoblock pump set

Supply only in replacement of connection pieces suitable for 5 HP pump

Supply only in replacement of CI upper & lower for 5 HP

Supply only in replacement of impeller gun metal for 5 HP

Supply only replacement of SS rotar sleeves for 5 HP

Supply only in replacement of sealing ring dor 5 HP

Taking up the unserviceable Submersible motor of capcity 7.5 Hp from borewell by lowering the chain pulling and colimin pipe and tansportaion to work for repair & Refixing the same after testing & commosioning of motor complete all as directed.. (Make of Pump for repair: Kirloskar , Location : P-103, New Pump House, CTVS ,Asheyana) .

Dismantling, Over hauling cleaning & Rewinding of motor 7.5 HP

supply only gun metal bush

supply only rotor sleeve

supply only water seal

supply only inlet

supply only guide bush

supply only ss sleeve

supply only cable Joint

Taking up the unserviceable Submersible motor of capcity 5 Hp from borewell by lowering the chain pulling and colimin pipe and tansportaion to work for repair& Refixing the same after testing & commosioning of motor complete all as directed. (Make of Pump: Kirloskar , Location :- P/H-02, P-18, MT and Fountain)

Dismantling, Over hauling cleaning & Rewinding of motor 5 HP

supply only gun metal bush

supply only rotor sleeve

supply only water seal

supply only inlet

supply only guide bush

supply only ss sleeve

supply only cable joint

Taking up the unserviceable Submersible motor of capcity 3 Hp from borewell by lowering the chain pulling and colimin pipe and tansportaion to work for repair& Refixing the same after testing & commosioning of motor complete all as directed. . (Make of Pump: Kirloskar , Location :Location :- MAP)

Dismantling, Over hauling cleaning & Rewinding of motor 3 HP

supply only gun metal bush

supply only rotor sleeve

supply only water seal

supply only inlet

supply only guide bush

supply only ss sleeve

supply only cable joint

S&F in repairs indicating light with bulb set of three

S&F in repairs DOL starter 3 phase 415 volt 7.5HP Relay range 20 to 32 Amp complete all as specified and directed.

S&F in repairs DOL starter 3 phease 415 volt 5 HP Relay range 9 to 14 Amp complete all as specified and directed

S&F in repairs DOL starter 1 phease 415 volt 3 HP Relay range 13 to 22 Amp complete all as specified and directedcomplete all as specified and directed.

S&F in repairs amp meter digital type 0-100 amps complete all as specified and directed

S&F in repairs On Load Changeover Switches 4 Pole, conformes to IEC 947-3, EN-06947-3 AC-23A, 160 amps , C01604POAV complete all as specified and directed.

S&F in repairs On Load Changeover Switches 4 Pole, conformes to IEC 947-3, EN-06947-3 AC-23A, 250 amps , C02504POAV complete all as specified and directed.

S&F in repairs Load Break swithes 4 pole, 160 amps, conformes to IEC 947-3 AC-23A, Front operated 3 pole 415V, 5m HZ. complete all as specified and directed.

Supply & fix Load Break swithes 4 pole, 250 amps, conformes to IEC 947-3 AC-23A, Front operated 3 pole 415V, 5m HZ.complete all as specified and directed.

S&F in repairs Electronic motor protection relay MPR200nX , inbuilt CT's (1 A to 88 A) as per IEC 947-4-1 O/L Range (A) 32-88 complete all as specified and directed.

S&F in repairs Electronic motor protection relay with in-built Earth fault protection MPR300, inbuilt CT's (1 A to 88 A) as per IEC 947-4-1 O/L Range (A) 32-88 complete all as specified and directed.

S&F in repairs Submersible pump controller in sheet enclosure type max motor output at 230v-3-Ph Relay Max range 20-32 A Cat part No. CS96167,Make:L&T, SIEMENS, C&S ELECTRIC,SINETRAC

S&F in repairs Supply monitoring devices type SM 501 (3Ph,3W), time deley On delay 5 sec and off delay 5 sec Cat part No.MG53BO, Make: L&T, SIEMENS, C&S ELECTRIC,SINETRAC,

S&F in repairs AC magnetic contractor type CM-40 as per IS 2959/1985 complete all specified as per directed

S&F in repairs MCCB 100 amps 4 pole 50 KA 415 volts 50 HZ in LT control panel complete all as specified .

S&F in repairs MCCB 4 pole 415 volt AC of capacity 63 amps 25 Ka cap complete all as specified .

S&F in repairs MCCB TP 415 volts 3 pole AC of capacity 63 amps complete all as specified .

S&F in repairs MCCB 200 amps 3 pole 36 KA 415 volts 50 HZ in LT control panel complete all as specified.

S&F in repairs MCCB 160 amps 3 pole 36 KA 415 volts 50 HZ in LT control panel complete all as specified.

S&F in repairs MCCB125 amps 3 pole 36 KA 415 volts 50 HZ in LT control panel complete all as specified.

S&F in repairs MCCB 250A 3 pole 50 KA 415 volts 50 HZ in LT control panel complete all as specified.

S&F in repairs MCCB160amps 3 pole 25 KA 415 volts 50 HZ in LT control panel complete all as specified.

S&F in repairs PVC flat sheathed submersible cable copper conductor of size 4.0 sqmm 3 core,1100 volt grade complete all as specified.

S&F in repairs PVC flat sheathed submersible cable copper conductor of size 6.0 sqmm 3 core,1100 volt grade complete all as specified.

S&F in repairs sumersiblecopper conductor cable of size 6 sqmm 4 core complete. Make- Kalinga / Finolex / Plaza

M&L for scrubbing out the rust deposited on the surface of centrifugal pump set including its base frame and preparing for applying paint and apply one coat of redoxide primer and two coat of synthetic enamel paint and marking SM /MES Number as directed. capacity of pump set 15 to 30 HP

M&L for applying one coat of synthetic enameled paint on old decorated steel/iron surfaces including preparing of surface complete all as specified and directed.

Demolition of cement concrete (unreinforced) as in any positionn.exc. 15 cm below or above ground level and removing rubbish off premises min 500m away from bldg complex, complete all as directed.

M&L for Cement concrete type B2 1:2:4 ( Using 20 mm graded stone Aggregate) as in surface channels and drains complete all as specifed and directed.

Dismantling of Blocked nozzles fixed on various fountain and refixing after cleaning / servicing and setting by trial and error complete all as specified and as directed.

S&F in repairs fountain nozzle (adjustable) of size 12mm brass complete all as directed.

S&F in repairs of fountain nozzle (adjustable) of size 15mm brass

Supply,install,testing and commissioning of LT indoor panel of suitable size 3 phase and neutral 415 volts fabricated out of 3 mm thick CRCA sheet powder coated ,front and back door openable suitable for and including 65x10 mm size copper bus bar, mounted on suitable DMC insulator and insulated with PVC sleeve not less than 2 mm thick and duly colour coated with (red,yellow,blue,and black) internal wiring with suitable size of PVC insulated copper wire, use with angle iron 50x50x6 mm frame to be used for bottom of the penal board ,IP 54 protection 30 cm blow ground level and 60 cm above ground leval ,grouted by using PCC foundation 1:2:4 type C1 with 20 mm graded stone aggregate , thimbling and cable entry boxes with cable gland including painting with two coat of powder coated paint using seven tank process complete and taking down old penal and connecting all cables incoming and outgoing by suitable lugs and connecting all with and including items catered under srl No 112.01 to112.14 here-in after-(Note- all the outgoing MCCB's shall be connected with suitable size copper strips bent to shape duly insulated as mentioned above with suitable insulator support (CPRI approved)) Location: Monkey Pump House

Incoming MCCB 160 Amps -1

Outgoing MCCB 100 Amps-2

Start delta starter 30 HP -2

LED indicating Lamp -3

Incoming MCCB 160 Amps 4 pole 25 ka -1

Outgoing MCCB 100 Amps 4 pole 25 ka-1

Star delta starter -30 HP (22 Amp - 50 Amp) as per IP 54 with CRCA Sheet steel material 50 Hz, 415 volt -1

LED indicating Lamp -4

Single phase preventer -1

Bus bar ratid 150 amp 3 phase neutral

M&L for development of bore well of 780 mm bore and up to 50 meters deep at the pressure not less than 6kgs/SqCm by using suitable air compressor and connected items to improve the yield of bore well complete all as specified and directed. NOTE: (I) Transportation of air compressor along with tools and accessories at different location for devolopment of bore well shall be the responsibility of contractor and the rate quoted will be deemed in the quoted rate). M&L for removing the blockage in bore well casing pipe at the depth not less then 50 meters from ground level by means of bocky or any means without damaging the casing (filter and blind pipe) upto the depth of bore.

PRASAD ELECTRICALS

R. S. Associates

CHAUHAN ENTERPRISES