CA NO GE(W)/HSR-47/2025-26 SPL REPAIR OF GARAGE FOR RECOVERY VEH BLDG NO P-2670B AND SPL REPAIR TO BLDG NO T-390 AT HISAR MIL STN UNDER GE (W) HISAR

Amount

M&L for 75mm Cement concrete type D-2,1:4:8 (40mm graded aggregate) as in sub base complete all as specified and directed.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor finishing cement concrete surface even and smooth using extra cement complete all as specified and directed.

M&L for 50 mm thick (1:3:6) Type-C-2 (using 40mm graded crushed stone aggregate) as in plinth protection complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

Taking down cement plaster of any description upto roof including necessary scaffoldings including raking out joints, hacking for key, scrubbing down with water etc. from wall & ceiling surfaces complete all as specified and directed.

M&L 15mm thick rendering in CM 1:6 to brick/concrete wall surfaces trowelled to even & smooth without using extra cement etc complete all as specified and directed.

M&L rendering 12mm thick in CM 1:3 on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L rough cast plaster mixture consisting of crushed stone or fine gravel aggregate size 6 to12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even on external wall upto cill height complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:4 in two layers of 10mm and 5mm, 15mm thick plaster shall be done with and including mixing of liquid WPC of approved make @ 200ml per bag of cement / manufacturer's instructions on brick/concrete wall surfaces of any description, and finishing the surfaces even and fair complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M & L two coat of oil bound distemper on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint of any tint over one coat of cement wash complete all as specified and directed.

Taking down chowkhats or frame n exc 1.50 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 Sqm but n exc 4 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified and directed.

S&F made single extruded WPC (Wood Polymer omposite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed.

S&F factory made single exturded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F 30mm thick factory made wire mesh solid WPC (Wood Polymer Composite) shutter of consisting density of 600 Kg/Cum an door to be panelled with SS mosquito mesh an XTN aluminium mesh for aditional strength and safety purpose hologram to be clearly visible on material, and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, Manufacture test certificates to be submitted complete all as specified and directed.

S&F Factory made mild steel window with side hung shutter (Box type) without glazing bars to receive wire guage, dovetailed or welded with and including necessary welding, reveting,tower bolt, handle, holdfast, & hinges and peg stay complete all as specified and directed.

S&F Factory made mild steel window with side hung shutter (Box type) with glazing bars to receive Glass, dovetailed or welded with and including necessary welding, reveting,tower bolt, handle,holdfast, & hinges and peg stay complete all as specified and directed.

S & F GI wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed in steel windows and wooden shutters complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality & glazing with oil putty in square n.exc 0.5 sqm each pane complete all as specified and directed.

S&F 3 mm thick figured glass pin head type in square n.exc 0.5 sqm each pane complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section and fixed, 200 mm size complete all as specified and directed.

S&F extruded aluminium alloy handles fabricated types, anodised, size 150 mm complete all as specified and directed.

S&F extruded aluminium alloy, anodised, sliding door bolt 250 mm in length with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body 150 mm long with rubber shoes fixed in repair complete all as specified and directed.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, hand rails, cupboards frame and similar work con- forming to Fe.290.Gde-E-165 with and including necessary cutting and welding complete all as specified and directed.

S&F 200mm long Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L preparation of new steel surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint over a cote of red oxide primer complete all as specified and directed.

M & L for preparations of new or previously untreated WPC dooor surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer to WPC door surfaces. complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brick work with old size flyash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in coping, benching and the like, including weathering slighthy rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, walls aprons etc (laid, bedded and pointed in any mortar) complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick of size not less than 0.30 Sqm of each slab over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with and including 15mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed. Note : Single piece tiles will be placed on the surface of stair case tread area.

Description all as per item No 37.00 above but kota stone slab (100/150mm x 550mm) and 20-25mm thick in riser of steps, skirting , dados and pillar laid over and including 10mm thick rendering to receive the stone in cement mortar 1:3 and jointed complete all as specified and directed. Note:- Kota stone in Stair case should be provided in single peice upto 1.5 m length

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and including sand cushioning layer for laying PCC interlocking paver block complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc. 30 cm high with synthetic enamel paint as required for marking of building numbers all as specified and directed. Note : Bldg No shall be done by using Stencil cutting to mark with neat finish.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe 410-W (Gde -E-250) quality-A all as specified and directed.

M&L for 100mm cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor such as veh garrages etc complete all as specified and directed.

Demolition of RCC Roofs, floors (other than ground floors), beams, staircases, landing, chajjas upto three storeys ,RCC Water tanks and similar suspended work of any type and description not otherwise described for complete all as specified and directed.

M&L RCC 1:2:4 Type-B1 (20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like incl necessary forms works complete all as specified and directed.

S&F TMT Mild Steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F TMT Mild Steel bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for formwork of soffits of suspended slabs such as roof slab, floor slabs, landigs, shelves and similar work, not exc 200mm thick rough finished surfaces of concrete complete all as specified and directed.

Dismantling roof tiles, single layer on roofs complete all as speified & directed.

Demolition of mud in roofs, any thicknes, including plastering and leeping (whether full thickness removed or only or part thereof) complete all as speified & directed.

M&L for preparation of roof surfaces (old or new) with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particles with and including providing 50 mm thick (average) PCC 1:2:4 type B-0 (using 20mm graded stone aggregate) with maintain the proper roof slope as in bedding, coping and kerb complete all as specified and directed.

M&L for providing 10mm thick polymer modified plaster in ratio 1:10 (1 part of polymer and 10 parts of cement with solid contents not less than 30%) over slab and applying priming coat of epoxy primer with resin and hardner with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurathene liquid membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm and applying 2nd coat solvent based polyurathene liquid mambrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm over dried 1st coat complete all as specified and directed. Make : M/s Asian Paints Ltd. / M/s STP Ltd/ M/s Sika India Pvt. Ltd.

M&L rendering 10 mm thick in CM 1:6 on fair face of brick /concrete surfaces of any description and finishing the surfaces even and smooth without using extra cement complete with complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash on undecorated surface complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash on undecorated surface complete all as specified and directed.

Providing and Erecting steel props (upto Full Height, Braced at centre, resting on wedge and block to support the structure provisionally during repair work and maintaining them in position till required and complete all as specified and directed.

Chipping of loose/ damaged /cracked / previously repaired / delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n.exc 50mm and disposal of rubbish off the premises to a distance not exc 50 mtrs including cleaning of reinforced concrete surface by air compressor complete all as specified and directed.

Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using product as approved by GE, with density 1.01 Kg/ltr at 30 degree celsius and consumption : 0.2 Kg/Sqm/coat complete all as specified and directed. Note: The mtrl to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar).

Supply and apply a cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and Product requirements: carbonation resistance: 2 mm of chemical compound as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N / Sqmm according to ASTM C 882-78 complete all as specified and directed. Note: The mtrl to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar)

Providng extra reinforcement with TMT bars as per site design requirement including straightening ,cutting ,bending, placing in position ,binding with GI wire of 18 gauge etc complete in all respects .Additional reinforecment with adequate lap length & rings at required spacing shall be tied with existing reinforcement using binding wire or welded complete as per site requirement and directions.

Providng and fixing rebar of required length & diameter with Epoxy Resin wherever required in RCC members including power drilling ,cleaning of holes, then rebars should be inserted in holes that should be filled with epoxy to ensure the bond as per manufacturer recommendation complete as per site requirement and directions all as specified. 16mm x 160mm

Description all as per item No 61.00 above but here-in-after 20mm x 200mm

Providing and fixing shear connectors of 16 mm dia TOR steel upto 160 mm Length Epoxy Resin RCC Members including power Drilling ,cleaning of holes ,insertion of epoxy ,placing shear connectors in position to ensure the bond as per manufacturer recommendation complete as per site requirement and directions.

M&L for Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface throughly and cleaning complete where ever required with using Product as approved by GE with Consumption: 0.4 kg/Sqm and Product requirements: Complies with ASTM C 881-78, Type II Grade 2 Class B+C complete all as specified and directed.

Providing and fixing water tight centering & shuttering including bolting, strutting, propping etc. including removal of form work from column, beam , slab etc. complete as per site requirement and directions.

Supply and apply a ready to use non shrink, cementitious free flow micro-concrete (<100 mm) using Product: SikaRep® Microcrete-4 + adequate coarse aggregate, Yield: approx 17 Ltr/bag (30 Kg) (depending on the size and quantity of coarse aggregate added), Product : SikaRep® Microcrete-4 or equivalent make in Fosroc / Thermax as approved by GE, Product requirements: compressive strength > 60 N/Sqmm (28 days) according to ASTM C 1107-99 complete all as specified and directed.

Supply and fixing of welded steel wire fabric n.exc 4 Kg per Sqm to wood or steel members or RCC structures etc complete all as per site requirement and directions

M&L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A' complete all as per specified and directed

Taking down carefully copper/ Aluminium point wiring ( light, fans, socket, power socket) complete including taking out existing unserviceable terminal boxes and conduit with switches/sockets/fan regulators and fittings such as ceiling roses, pendants, tube lights fittings lamp holders, brackets light fittings, rectangular blocks DB MCCB etc and making good disturbed surface of wall/ floor etc to match with the existing the surface etc complete all as specified and directed.

Taking down old unserviceable submain wiring including fitting & fixtures and making good of the surface to match with the existing complete all as specified and directed.

Material and labour for point wiring with 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multistranded copper conductor for one light/fan/bell point in and including PVC rigid non metallic existing concealed conduit 19/20 mm dia medium duty, ISI marked to be terminated & including pressed modular steel boxes & cover plate of module as required on site. Including 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multistranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment complete all as specified and directed.

Description all as per item No 71.00 (here-in-before) but One three pin 5 Amp socket outlet point on indep board controlled by one nos, one way switch on independent board complete all as specified and directed.

Description all as per item No 71.00 (here-in-before) but One three pin 5 Amp socket outlet point on same board controlled by one nos, one way switch on same board complete all as specified and directed.

Description all as per item No 71.00 above but point wiring with 2.5 sq mm single core FRLS cables and earth continuity wire with 2.5 Sq mm single core cable for one 3 pin 15 Amps socket out let point controlled by one nos, one way switch on independent board complete all as specified and directed.

S&F Modular switch 1 way 6A 1 module Single pole, one way, 230 volts all as specified and directed

S&F Modular switch 1 way 16A 1 module all as specified and directed

S&F Modular socket 6A -2/3 pin combined 2 module type 230 volts AC complete all as specified and directed.

S&F Modular socket 6A/16A -2/3 pin combined 2 module type AC complete all as specified and directed.

S&F Modular lamp holder, insulated body with back plate suitable for batten fittings and complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Modular ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F modular fan step regulator 120W-2 module suitable for 1200/1400 mm sweep ceiling fan etc complete all as specified and directed.

S & F in repair for wall mounted LED tube light fitting 20 watts batten not less than 120 lumen/watt for surface mounted, high transmissitivity diffuser, high lumen output box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S&F in repair Sheet metal enclosure distribution board SPN, 8 way, double door powder coated, protection class IP-42 suitable for mounting MCB DBs confirming to IS-13032, IS-8632,BS5484 with min 200 Amp rating copper bus bar complete all as specified and directed.

Supply and fixing in repair MCBs SP 6 to 32Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed. Note : Make of the MCB should be the same as that of DB

Supply and fixing in repair MCBs SPN 40Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed. Note : Make of the MCB should be the same as that of DB

S&F in repair Sheet metal enclosure distribution board TPN, 4 way, double door powder coated, protection class IP-54, isolated neutral bar, mechanical impact strength IK 09 suitable for mounting MCB & /MCCB DBs confirming to IS-13032, IS-8632,BS5484 with min 200 Amp rating copper bus bar and grouting, fixing on wall with nut bolts washers proper with PCC works complete all as specified and directed.

Supply and fixing in repair TPN 63 Amps, 215 volts, 16 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed. Note : Make of the TPN should be the same as that of DB

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessories ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable for phase, one run of 6 sqmm cable for earthing and one run of PVC conduit will be measured as one unit.

Supply, laying, jointing, testing and commissioning of size 35 sqmm 3.5 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors IS-7098, laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified and directed. Note : Excavation, earth work, sand cushion & brick protection shall be paid separately.

M&L for providing/cutting the round/ square hole of required size in wall finishing the same for disturbed surfaces complete all as specified and supply and fixing propeller type AC ventilating fans, single phase , 230 volts 250 mm sweep complete and grouting the ragged bolts in wall fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writing MES No. with black synthetic enamel paint 2.0 cm height complete all as specified and directed.

S & F in repair for Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source not less than 120 lumen/watt and electronic driver of capacity 25/35 watts with pre wired and necessary mounting arrangements and provision of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including 40 mm dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Excavating in trenches in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.5 metre in depth for taking out of unserviceable LT underground/laying cable complete all as specified and directed.

Returning, filling in trenches in any type of soil and spreading in layers not exceeding 25mm thick complete all as specified and directed.

Removal of surplus soil (any type of soil obtained from excavation) to a sistance not ecxceeding 50 metre and depositing where directed all as specified.

M&L for bricks covering to under gound electric cable using sub class 'B' bricks laid dry, flat perpendicular to the direction of the cable complete all as specified and directed.

Supplying, filling in trenches, spreading, leveling sand cushioning 8cm below cable and 15 cm above the cable for under ground cable complete all as specified and directed.

Shiva Constructin Co. (BID ID -3516788)

S K BUILDERS (BID ID -3522178)

M/S RR ENGINEERING CO (BID ID -3522154)

Balaji Construction Co. (BID ID -3522269)