REPAIR TO JOINERY, PLASTERING, FALSE CEILING AND OTHER B/R WORKS ETC AT ZONE B OF AF STN SONEGAON, NAGPUR.

Amount

Taking down cement plaster of any description, including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M & L for rendering on walls, 15mm thick in cement mortar (1:4) on fair faces of brick work, with WPC @ 3% by wt of cement, surface finished even and smooth without using extra cement complete all as specified and as directed. Note: - WPC shall be measured and paid separately.

M & L for rendering on walls 15 mm thick in cement mortar (1:6) on other than fair face of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound.

M & L for two coats of cement base paint on newly plastered surfaces of walls including preparation of surfaces, complete all as specified and as directed.

M & L for two coats of oil bound distemper over one coat of priming chalk whiting on new plastered surfaces preparatory to distemper including preparation of wall surfaces with 2mm thick wall care putty complete all as specified and as directed.

M &L for one coat of Oil Bound Distemper on old existing plastered ceiling surface including preparation of surface on Ceiling complete all as specified and as directed.

Demolition of cement concrete unreinforced in ground floor and paving not exceeding 15 cm thick (below or above G.L) complete all as specified and as directed.

M & L for plain cement concrete Type B-O, 1:2:4 (using 12.5 mm graded stone aggregate) in roof kerbs, mud stops, rounded or chamfered on edges complete all as specified and as directed.

M & L for 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) as in sub base complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement motor bedding (But not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

M & L for glazed ceramic coloured tiles on vertical surface 350X450X7 mm thick, over and including 10mm thick rendering in CM 1:4. Set and jointed in neat cement slurry and pointed in where or coloured cement to match, complete all as specified and as directed.

M & L for coloured non-skid ceramic tiles 7-8 mm thick (square/rectangular), area of each tiles exc 0.18 Sqm but n exc 0.38 Sqm in floors etc. (including spacers in tiles where required and directed) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) finished even and rough to receive the top layer complete all as specified and as directed.

M & L for coloured non-skid ceramic tiles 7-8 mm thick (square/rectangular), area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) finished even and rough to receive the top layer complete all as specified and as directed.

M & L for light shade Vitrified ceramic tiles 10 mm thick (Squarer/ rectangular) Polished, area of each tiles n. exc. 0.36sqm, in floors etc. set and jointed in neat cement slurry over and including bedding layer of screed bed 15 mm thick in CM 1:6 and pointed in white/colour cement to match complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and as directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S & F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and as directed.

Providing and fixing in repair 08 mm thick PVC Laminated gypsum Ceiling Tiles with MPL Film for diffusing heat & moisture (rear side) Superior Humidity Resistance RH 90% PVC laminated gypsum ceiling tiles strong and long-lasting made of high quality paper-faced gypsum board with a PVC layer on the surface and aluminium foil on the reverse. PVC laminated gypsum ceiling to be environmentally friendly, light-weight, high-quality decorative ceiling tiles, fireproof, water-resistant, and corrosion-resistant to be fixed as per manufacturer’s instructions all as specified and directed laid over and including grid work of size 605X605 mm, made out of 0.5mm thick GI Tee 32X24 mm for main , 25X24 mm for cross Tee and 24X24 mm fixed on wall , powder coated finish on exposed faces of Tee and angle , hung from ceiling using 2mm dia GI suspension wire fixed with adjustable clip spaced a 1200mm on main runners including making niches for fan and light complete all as specified and as directed by Engr-in-Charge including Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets.

S & F cast iron nahani trap with grating including joint to waste pipe fixed in cement concrete Type B-1 (1:2:4) of 100 mm dia of outlet complete all as specified and as directed.

M & L for Cutting existing 15 mm steel tubing for alterations or additions (each cut measured) complete all as specified and as directed.

Taking up or down 15 mm bore GI tubing pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

All as per Item No 25.00 above but for 20 mm dia GI tube complete all as specified and as directed.

S & F 15 mm bore galvanized steel tubing medium grade with all fittings and fixed to walls, ceiling, floors etc complete all as specified and as directed.

All as per Item No 27.00 above but for 20 mm dia GI tube complete all as specified and as directed.

S & F in repair 15 mm bib tab fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for pipe or for brass ferrule and fixed complete all as specified and as direcrted.

S & F in repair 15 mm bore Bib taps standard of PTMT any colour high pressure screwed for iron pipes and fixed complete all as specified and as directed.

S & F in repair 15 mm stop valve fancy type chromium plated with high pressure, with crutch butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S & F in repair 15 mm stop valve cast copper alloy with fancy type chromium plated with long shank and cup (concealed), high pressure, with crutch butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S & F in repair 15 mm Pillar taps, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without letterer 'Hot' or 'Cold’ with long screwed shank and flynut, screwed for iron pipe and fixed complete all as specified and as directed.

S & F in repair Brass chromium plated shower rose 125mm size complete all as specified and as directed.

S & F in repairs sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S & F PVC cabinet size 450x600mm with looking mirror complete all as specified and as directed. Make: - Prayag or equivalent.

S & F repair vitreous china white wash hand basin flat back size of 550x400mm including brackets including cutting, pinning in ends of brackets or erecting stand complete all as specified and as directed.

S & F in repair vitreous china wash down water closet (Pedestal) P or S trap including PVC seat cover closed pattern with flat bottom and cover and mild steel chromium plated hinge device, connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe joint to socket or stopper etc, complete all as specified and as directed.

S & F in repair Vitreous China Squatting pan, Orissa pattern, size 580 x 440 mm white with `P' or `S' trap, front or back inlet and integral foot rests including connection to trap, to flushing pipe etc. complete including making good to floor complete all as specified and as directed.

S & F in repair Vitreous China urinals, (half stall urinal) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed.

S & F Urinal spreader 300 mm length of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60 gms) complete all as specified and as directed.

S & F in repair 10 ltrs capacity PVC valve-less, symphonic action type, flushing cistern, low level, white, with inlet ,ball valve, float and handle including flush pipe (long bend) for low level cistern complete all as specified and as directed.

S & F PVC SWR pipe 110mm single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S & F PVC SWR 110mm bends complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S & F in repair stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 100mm dia pipe complete all as specified and as directed.

S & F in repair PVC connection 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S & F in repair Waste coupling of PTMT 32-40mm dia (half or full threaded) (minimum weight - 45 gms) complete all as specified and directed.

Taking down chokhat with shutter (without taking down shutters from the frame) n. exc 1.5 sqm complete all as specified and directed.

Taking down chowkhat with shutter (without taking down shutters from the frame) exc 1.5 sqm but n. exc 4 Sqm complete all as specified and directed.

Taking down Shutters of any description n exc 1 sq. m each complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm and n. exc 2 sqm each complete all as specified and directed.

S & F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S & F Pressed steel frames for doors of size 105x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directred.

S & F 30mm thick 2nd class HW plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) complete all as specified and as directed.

S & F 30mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and as directed.

Taking down worn out u/s GI wire cloth and S&F for Galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm in metal/ wooden almunium frames complete all as specified and as directed.

S & F in repair Steel windows with side hung shutters including projecting type hinges, with steel handle, and steel peg stay, complete with glazing bars dovetailed or welded complete all as specified and as directed.

S & F Steel ventilator in repair with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S & F in repair 150 mm long SS, barrel tower bolts of extruded section complete all as specified and as directed.

S & F in repair 300mm long sliding door bolts with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bots and sliding bolts of extruded or cast aluminium alloy complete all as specified and as directed.

S & F in repair butt hinges 100 mm medium weight, cold rolled mild steel complete all as specified and as directed.

S & F in repair 150mm long SS extruded handles fabricated type, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads complete all as specified and as directed.

S & F 3mm plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm each pane complete all as specified and directed.

S & F 3mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane in repair complete all as specified and directed.

S & F 5 mm thick sheet glass, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F factory made solid panel PVC door frame of size 50mmx47mm out of 5mm plain colour PVC sheet reinforced with M.S. square tube, all as per specification and drawing complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for top rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

M & L for preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paints over and incl a coat of pink primer complete all as specified and directed.

M & L for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paints over and including a coat of red oxide primer complete all as specified and directed.

S & F in repairs Aluminium extruded section body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851-1000 mm in width & weight between 61 to 80 Kg. complete all as specified and directed.

S & F in repair towel rail CP 20 mm dia 600 mm long complete all as specified and directed. Make: - Jaquar or equivalent

S & F HDPE waste pipe for drain of water from wash basin, sink, urinals and Other places complete all as specified and directed.

S & F in repair angle cock 15mm CP cast copper screwed down for iron pipe complete all as specified and directed.

M & L re-securing or easing and adjusting wooden door shutter/ window shutter of any type Taking / without taking down shutters and re-fixing in the same complete all as specified and directed.

M & L re-securing or easing and adjusting aluminium door shutter/window shutter of any type taking / without taking down shutters and re-fixing in the same complete all as specified and as directed.

M & L easing / adjusting of steel doors/ windows and oiling/ greasing for smooth functioning complete all as specified and directed.

Supply and fixing anodised aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 65mm x 38mm x 1.55 mm and section of bottom and lock rail shutter frame of 45mm x 45mm x 1.55 mm with and including panels of 5 mm thick plain/frosted float glass, and all necessary fittings complete all as specified and as directed.

S & F for Powder coated aluminium sliding windows for two track with 4 mm thick plain/ coloured glass fixed with powder coated aluminium standard beads/glazing clips having weight not less than 300gm per RM, locking arrangement etc and aluminium frame of size 64mmX45mmX1.55mm and shutter of section 20mm X 40mm X 1.55mm including taking down old steel windows with necessary all fittings complete all as per manufacturer's instructions and all as specified and as directed.

S & F in repair 25mm dia Harrison rails (Curtain Rods), mild steel, chromium plated with fixing (CP coloured) brackets, stops, rollers etc. complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

M & L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete drilled for fixing of steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging: also fastening conforming to Fe-290 Gde-E-165 and fixing complete all as specified and as directed.

S & F in repair 30mm thick PUF wall /cladding insulated panel versatile, offering strength and durability Made from high-quality metal, providing weather resistance and corrosion protection Energy-efficient, offering thermal insulation and soundproofing including removing old old U/S panels by dismantling the existing structure and re-fixing in the same position complete all as specified and as directed.

M/s Rahul Traders (BID ID -3490064)