Interior , Civil and Electrical works and installation of AC and AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Sub-Schedule-I: Items of General Civil works Scheduled in Civil DSR 2023 and Items directly driven from DSR 2023

NIT Number CWC/RO-MUM/Engg./26-27/03

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NAME OF CONTRACTOR

Sr.No. Name of Work Total Amount (In Rs.) Quoted rates (Above/Below/At par) Rate to be quoted in percentage (%) Quoted % In Words Quoted amount in figure

1 Sub-Schedule-I CIVIL DSR 2023 3075114.56 -

TOTAL QUOTED PRICE= -

Amount Quoted (In Words)

Note CWC estimated amount of this sub schedule, after considering prevailing Cost Index and applicable GST& Labour Cess etc. complete is Rs. ₹ 3147376.00

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Sub-Schedule -II: Items of General Civil works not scheduled in Civil DSR 2023 (Market Rate Items)

NIT Number CWC/RO-MUM/Engg./26-27/02

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NAME OF CONTRACTOR -

Sr. No. Name of Work Total Amount (In Rs.) Quoted rates (Above/Below/At par) Rate to be quoted in percentage(%) Quoted % In Words Quoted amount in figure

1 Sub-Schedule -II: CIVIL MR ITEMS 13826708 -

TOTAL QUOTED PRICE= -

Amount Quoted (In Words)

Note CWC estimated amount of this sub schedule, after considering prevailing Cost Index and applicable GST& Labour Cess etc complete is 1,37,96,697.62

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Sub-Schedule-III: Items of General ELECTRICAL works Scheduled in ELECTRICAL DSR 2025 and Items directly driven from DSR 2025

NIT Number CWC/RO-MUM/Engg./26-27/03

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NAME OF CONTRACTOR

Sr.No. Name of Work Total Amount (In Rs.) Quoted rates (Above/Below/At par) Rate to be quoted in percentage (%) Quoted % In Words Quoted amount in figure

1 Sub-Schedule-III ELECTRICAL DSR 2025 2944729 -

TOTAL QUOTED PRICE= -

Amount Quoted (In Words)

Note CWC estimated amount of this sub schedule, after considering prevailing Cost Index and applicable GST& Labour Cess etc. complete is Rs. ₹ 30,01,268.00

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Sub-Schedule-IV: Items of General Electrical works not scheduled in Electrical DSR 2025 (Market Rate Items)

NIT Number CWC/RO-MUM/Engg./26-27/03

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NAME OF CONTRACTOR

Sr.No. Name of Work Total Amount (In Rs.) Quoted rates (Above/Below/At par) Rate to be quoted in percentage (%) Quoted % In Words Quoted amount in figure

1 Sub-Schedule-IV ELECTRICAL MR ITEMS 2907079 -

TOTAL QUOTED PRICE= -

Amount Quoted (In Words)

Note CWC estimated amount of this sub schedule, after considering prevailing Cost Index and applicable GST& Labour Cess etc. complete is Rs. ₹ 29,07,079.00

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Sub-Schedule V: VRV/VRF Air Conditioning System work

NIT Number CWC/RO-MUM/Engg./26-27/03

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NAME OF CONTRACTOR

Sr.No. Name of Work Total Amount (In Rs.) Quoted rates (Above/Below/At par) Rate to be quoted in percentage (%) Quoted % In Words Quoted amount in figure

1 Sub-Schedule V: VRV/VRF Air Conditioning System work 8168290 -

TOTAL QUOTED PRICE= -

Amount Quoted (In Words)

Note CWC estimated amount of this sub schedule, after considering prevailing Cost Index and applicable GST& Labour Cess etc. complete is Rs. ₹ 81,68,290.00

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Sub-Schedule VI: Audio Visual/ELV Works

NIT Number CWC/RO-MUM/Engg./26-27/03

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NAME OF CONTRACTOR

Sr.No. Name of Work Total Amount (In Rs.) Quoted rates (Above/Below/At par) Rate to be quoted in percentage (%) Quoted % In Words Quoted amount in figure

1 Sub-Schedule-VI Audio Visual/ELV Works 4306946 -

TOTAL QUOTED PRICE= -

Amount Quoted (In Words)

Note CWC estimated amount of this sub schedule, after considering prevailing Cost Index and applicable GST& Labour Cess etc. complete is Rs. ₹ 43,06,946.00

CENTRAL WAREHOUSING CORPORATION

(A Govt. of India Undertaking)

Price Bid (Summary Sheet)

NIT Number CWC/RO-MUM/Engg./26-27/03

Name of Work Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai.

Name Of Contractor -

Sd.-I SCH_I (CIVIL DSR) 3147376 -

Sd.-II SCH_II (CIVIL MR) 13796697.62 -

Sd.-III SCH III (ELECTRICAL DSR) 3001268

Sd.-IV SCH IV (ELECTRICAL MR) 2907079

Sd.-V SCH V (VRV/VRF Air Conditioning System work) 8168290

Sd.-VI SCH VI(Audio Visual/ELV Works) 4306946

Grand Total (In Figures)

Grand Total (In Words)

Pre-Qualifying (PQ) Proforma: Bidder Information Summary

{To be Filled by Bidder in sheet uploaded over portal and then to be submitted along with technical bid}

Name of Works: Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

NIT Reference Number:

SL Description Details (filled by Bidder)

General Details of Bidder

See PQC S/n (1) to (4): Appendix-II of NIT

1 Name of the Bidder

1.1 Bidder Address, (registered)

1.2 Bidder Organization ID /CIN in case of Company

1.3 Bidder Telephone number

1.4 Bidder E-mail address

2 Type of Bidder constituent (Organization)

(JV not allowed for these works)

2.1 Attested copy of documents in support of Bidder Organization Type

(See ITB-Appendix IV clause number 3.2: 1 (b): Organization Details and

Appendix-II of NIT: List of documents required in support of Bidder Legal Entity.

2.2 Current List of Directors/Partners: as applicable

3 Name of the person holding the power of attorney for this Bid

3.1 Designation

3.2 Contact details of person holding the power of attorney

3.3 Attested Copy of Power of Attorney to sign & submit the Tender (as per format given in EXHIBIT-III of Appendix-II)

Name of the All location for which bid is submitted

4 Earnest Money Deposit (EMD) of Amount as mentioned in APPENDIX-1 (TIS) through e- payment Gateway

5.1 PF Registration code number of Bidder

5.2 COPY of PF Registration number of Bidder

6.1 GST Registration code number of Bidder

6.2 COPY of GST Registration number of Bidder

7.1 PAN of the Bidder

7.2 COPY of PAN of Bidder

8.1 Whether Enlisted /Empaneled with CPWD/ MES/ Railway/ PWD/ CWC/any other PSU etc. if any,

8.2 Copy of Enlistment/Empanelment certificate Submitted or Not

9 Whether Bidder is executing or completed any work awarded by CENTRAL WAREHOUSING CORPORATION in Past Three FY Year (FY 2023-24, FY 2024-25, FY 2025-26) and Current FY 2026-27.

10.1 Affidavit along with this PQ Performa (EXHIBIT-I) on NJS paper signed and submitted after filling necessary details.

10.2 Declaration of near relatives (EXHIBIT-IV) submitted.

Technical Eligibility Criteria:

See PQC S/n (5) in Appendix-II of NIT for details & qualifying limits.

11 Particular Technical Experience w.r.t. Similar Nature of Work:

11.1 Brief of Similar Nature Work Experience-1

I Work order/ contract agreement ref number and date

Ii Name of client issued the work order and completion certificate

iii Completion certificate -ref number and date

iv Total value of work completed (Rs.)

V Stipulated date of completion

vi Actual date of completion

vii If LD is levied: Amount / period of delay for which Liquidity damage is levied by client (if any)

viii Copy of completion/experience certificate of work and Copy of Agreement/Workorder issued by Client is submitted as per format given in EXHIBIT-V or EXHIBIT-VI or EXHIBIT-VII as applicable

11.2 Brief of Similar Nature Work Experience-2

I Work order/ contract agreement ref number and date

Ii Name of client issued the work order and completion certificate

iii Completion certificate -ref number and date

iv Total value of work completed (Rs.)

V Stipulated date of completion

vi Actual date of completion

vii If LD is levied: Amount / period of delay for which Liquidity damage is levied by client (if any)

viii Copy of completion/experience certificate of work and Copy of Agreement/Workorder issued by Client is submitted as per format given in EXHIBIT-V or EXHIBIT-VI or EXHIBIT-VII as applicable

11.3 Brief of Similar Nature Work Experience-3

I Work order/ contract agreement ref number and date

Ii Name of client issued the work order and completion certificate

iii Completion certificate -ref number and date

iv Total value of work completed (Rs.)

V Stipulated date of completion

vi Actual date of completion

vii If LD is levied: Amount / period of delay for which Liquidity damage is levied by client (if any)

viii Copy of completion/experience certificate of work and Copy of Agreement/Workorder issued by Client is submitted as per format given in EXHIBIT-V or EXHIBIT-VI or EXHIBIT-VII as applicable

See PQC S/n (6) in Appendix-II of NIT for details & qualifying limits.

Information on Financial Capabilities & Turn over

12.1 Annual Financial Turnover-Total Revenue (Income) (as per CA certificate and audited P&L Account)

Iii FY 2023 –24

Vi FY 2020-21 (only when audited turnover for FY 2025-26 is not available)

12.2 The average of financial turnover for the last three financial years i.e. FY 2025-26, FY 2024-25 and FY 2023-24 Or FY 2022-23 (FY 2022-23 to be referred only when Audited turnover of FY 2025-26 is not available)

See PQC S/n (7) in Appendix-II of NIT for details & qualifying limits.

13 Annual Financial Turnover-Total Revenue (Income) from Construction Works (as per CA certificate and audited P&L Account)

iii FY 2023 –24

vi FY 2020-21 (only when audited turnover for FY 2025-26 is not available)

14 Annual Financial Turnover-Total Revenue (Income) from Electrical Works (as per CA certificate and audited P&L Account)

iii FY 2023 –24

vi FY 2020-21 (only when audited turnover for FY 2025-26 is not available)

15 Annual Financial Turnover-Total Revenue (Income) from Mechanical Works (as per CA certificate and audited P&L Account)

iii FY 2023 –24

vi FY 2020-21 (only when audited turnover for FY 2025-26 is not available)

See PQC S/n (8) of Appendix-II of NIT for details & qualifying limits.

16 Bidder's Profit after Tax (PAT) (as per CA certificate and audited P&L Account)

iii FY 2023 –24

vi FY 2020-21 (only when audited turnover for FY 2025-26 is not available)

17 Bidder's Total Net worth (as per CA certificate and audited P&L Account)

ii FY 2024- 25 (only when audited Balance Sheet for FY 2025-26 is not available)

18 copy of Audited Balance Sheets and Profit & Loss Statements for Annual financial turnover/ revenue (income), PAT & NETWORTH of Bidder (in support of Information provided above) to be submitted with Bid

iii FY 2023 –24

vi FY 2020-21 (only when audited turnover for FY 2025-26 is not available)

19 Copy of Chartered Accountant’s Certificate as per format given in EXHIBIT VIII in support of information provided above on Annual financial turnover/ revenue (income), PAT of Bidder.

20 Chartered Accountant’s Certificate as per format given in EXHIBIT IX in support of information provided above on Net worth of Bidder.

21.1 Total Solvency in Rs. As per Banker certificate issued for this purpose

21.2 Banker's certificate in support of the above information as per EXHIBIT X submitted.

See PQC S/n (9) in Appendix-II of NIT for details & qualifying limits.

22 Duly signed copy of Pre Contract Integrity Pact as per EXHIBIT-XI

See PQC S/n (10) in Appendix-II of NIT for details & qualifying limits.

23 Certificate(s) issued by Client(s) for execution of minimum specified quantities of special works during a FY year along with summarized breakup of these works as per EXHIBIT-XII.

See PQC S/n (11) in Appendix-II of NIT for details & qualifying limits.

24.1 Available Bid Capacity of Bidder in Figures in INR:

24.2 Certificate as per EXHIBIT XIII duly filled with all details and capacity derived from specified formula -Submitted

See PQC S/n (12) of Appendix-II of NIT for details & qualifying limits.

25 Details of Personnel & Equipment as asked in Appendix II of NIT submitted with summarized breakup on letter head of Bidder.

PRICE BID AND SCHEDULE

NAME OF WORK - Interior , Civil & Electrical works & installation of AC AV system for new office block for the Newly Hired Regional Office of Central Warehousing Corporation, Mumbai

SCHEDULE I ( CIVIL DSR)

Sr. No. Description of Items Qty Unit DSR Rate Amount DSR 2023

1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size

25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing ompound , jointing tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 168 sqm 1355.8 227774.4 12.45.1

2 Painting for walls

a) Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 698 sqm 262.7 183364.6 13.26

b) Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. - Two coats 698 sqm 142.8 99674.4 13.83.2

c) Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 698 sqm 73.95 51617.1 13.85.3

3 Paint for ceiling

a) Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 773 sqm 262.7 203067.1 13.26

b) Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. - Two coats 773 sqm 142.8 110384.4 13.83.2

c) Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface 773 sqm 73.95 57163.35 13.85.3

having VOC content less than 50 grams/litre

4 TEXTURE PAINT:

a) Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 50 sqm 262.7 13135 13.26

b) Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. - Two coats 50 sqm 142.8 7140 13.83.2

c) Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 50 sqm 73.95 3697.5 13.85.3

5 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar 23.19 cums 2060.2 47776.04 15.7.4

6 Providing and laying Vitrified tiles in floor with different sizes (thickness 737 sqm 2264.9 1669231.3 11.49.4

to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer,

in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

7 CEMENT PLASTER (IN FINE SAND) - 12 mm cement plaster:- 1:4 (1 cement : 4 fine sand) 250 SQM 347.05 86762.5 13.1.1

8 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved 3.5 SQM 1267.95 4437.83 8.31

make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade

9 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, 11 each 12071.75 132789.25 17.5.1

with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :

2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls

and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic

flushing cistern

10 Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, 9 sqm 4746.2 42715.8 16.86.1

colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4(1cement

: 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as

per direction of Engineer-in-Charge. With granite stone of area less than 0.50 sqm.

11 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all -

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge .Concealed work, including cutting chases and making good the walls

20 mm nominal dia Pipes 120 mtr 537.6 64512 18.8.2

12 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting -

with anti corrosive bitumastic paint, cutting chases and making good the wall :

20 mm nominal dia Pipes 110 mtr 635.2 69872 18.11.2

Total 3075114.56

SUB SCHEDULE II (CIVIL MR)

Sr. No. Description of Items Qty Unit RATE Amount

1 PLYWOOD BOXING: Providing & fixing 19mm Commercial Ply boxing with 1mm thick laminate necessary supports & framing where ever required complete as per detail / instruction by Design Team / site-incharge 56 sqm 11541 646296

2 Wooden florring AC3 - Providing and laying of wooden planks flooring of AC3 grade, 8mm thick of size 193 mm * 1214 mm over the specified area with following specifications the floor which recieves the flooring to be thoroughly cleaned as per manufacturer's specification. The plank is to be laied over a bed of manufacturer's approved adhesive spread evenly over the entire floor . The rate shall include cutting , trimming, fixing and cleaning away of resedual material to location as directed. The measurements of laid flooring will be actual laid area. 49 SQM 3463 169687

3 Wall paper: Pasting and applying wallpaper of approved make, design and shade including wastage. 19 SQM 3077 58463

4 FROSTED FILM: Providing and pasting frosted film on glass work as required & as directed . 93 SQM 2821 262353

5 Rolling BLINDS :- Providing & fixing Roller blinds comprising of polymer coated fibre fabric with minimum openness factor of 3% and max. of 5% as per AS standards. The fabric shall be fire retardant and have high heat reflection ratios. 73 SQM 2821 205933

6 Soft Board : Pinup Soft board with 450mm height , for manger cabins side table 2.5 SQM 8977 22442.5

7 Writing Board: White Magnetic Writing board with 450mm height , for manger cabins side table 2.5 SQM 8977 22442.5

8 PANTRY OVER HEAD STORAGE : Providing & Fixing storage Cabinate of depth 300mm for filing in 18mm Plywood all sides laminated for Top, Bottom, Shelves, Laminated from both inside & outside as instructed by Design Team. Costs to include for all hardware & fittings like handles, locks, Tower bolt, lipping for legs, etc. complete as per drawing & details 3.5 SQM 26930 94255

9 UNDER COUNTER STORAGE : Providing & making Under Counter Cabinet below Pantry Counter with 1" x 1" hard wood frame & 18mm Marine Ply Laminated both side complete as per detailed drawing. Rate is inclusive of all hardware and fittings like handles, hinges, lipping, Magnet Catch, making grooves etc. Complete as per drawing details / Instruction by Design Team / site-incharge. 3.5 SQM 26930 94255

10 WET PANTRY AREA : Providing & Fixing Granite Counter 600mm Deep x 750mm High in shape and design as per given approved drawing & 18mm Thk. with 100mm Full round facia in front and 100mm High upstand on the Wall in matching granite including 20mm Thk 1:4 Cement Mortar and Kaddappa/Marble with Kaddappa Verticals and shelves as indicated, making cut-outs for Sink, Plumbing Fixtures etc., Cost to include for all Granite Vertical Pattis, Facias, Splash-Back Pattis, Granite Skirting etc., Polishing including Edge Polishing, Washing, Cleaning and Finishing the Wall in Paint finish below the Mortar backing Complete as per drawing detail / instruction by Design Team / Site-incharge.(Running Length of Counters to be measured along their Center lines and paid for)sink not included. 5.5 RMT 11799 64894.5

11 SOUNDPROOF BASE LAYER : Providing and fixing 5mm thick sound barrier sheet (Sound Packing Sheet) having Sound Transmission Class (STC) rating of minimum 42.7 dB(A), suitable for professional acoustic insulation applications in walls, ceilings, and floors.The material shall be dense, flexible, and designed for high-performance airborne sound insulation, suitable for studios, commercial buildings, and industrial applications.The installation shall ensure tight joints, proper sealing, and complete coverage to achieve specified acoustic performance.By directly pasting the sheet onto wall surface using approved high-strength adhesive 107 SQM 4283 458281

12 GI FRAME : Panels shall be fixed over GI framework comprising 50mm x 35mm x 1.0mm thick GI channels supported on 40mm x 40mm x 5mm GI angle cleats spaced at 1200mm x 1200mm c/c, anchored to solid wall maintaining required air gap as per approved drawings. GI channels shall be fixed horizontally at 600mm c/c. Panels shall be mounted using aluminum extruded keel sections, special aluminum splines and clip system. Panel edges shall be connected using dowels to prevent sagging and ensure proper alignment.Panels shall be fixed over GI framework comprising 50mm x 35mm x 1.0mm thick GI channels supported on 40mm x 40mm x 5mm GI angle cleats spaced at 1200mm x 1200mm c/c, anchored to solid wall maintaining required air gap as per approved drawings. GI channels shall be fixed horizontally at 600mm c/c. Panels shall be mounted using aluminum extruded keel sections, special aluminum splines and clip system. Panel edges shall be connected using dowels to prevent sagging and ensure proper alignment. 107 SQM 13850 1481950

WOOL INSULATION : Providing and fixing 50mm thick synthetic/mineral wool insulation in roll/slab/blanket form, manufactured from fine synthetic or mineral fibers bonded with thermosetting resin, having density ranging from 12 kg/m³ to 48 kg/m³ as per approved specification.The insulation material shall have thermal conductivity between 0.032–0.040 W/mK, providing effective thermal insulation and energy efficiency. The material shall also possess high sound absorption characteristics suitable for acoustic applications.The insulation shall be lightweight, flexible, moisture-resistant, non-corrosive, rot-proof, and resistant to fungal growth. It shall be non-combustible with melting point above 1000°C (depending on type) and conform to relevant fire safety standards.The material shall be fixed within wall/ceiling partitions or sandwiched between board layers as per approved drawings and site requirements, ensuring tight butt joints and proper coverage without gaps.

FABRIC PANELS: Providing and fixing factory-manufactured Fabric Wrapped Acoustic Panels of size 1200mm x 1200mm and 25mm thickness, suitable for wall and/or ceiling acoustic treatment.Panel core shall be Glass Fiber / Wood Wool / Semi-Rigid Foam (as per approved acoustic design), finished with acoustically transparent fabric in approved colour and texture. Panel weight shall range from approximately 2.5 to 4.5 kg/sqm depending on core selection.The panel system shall achieve NRC up to 0.95 when tested as per IS 8225, ISO 354, and ASTM C423. The system shall have a critical frequency of 1.45 at 500 Hz and Sabin value of 1.47 at 1000 Hz. Fire performance shall comply with Class 1 rating as per BS 476 Part 7:1997 when used with fire-rated core and fabric. The product shall be low VOC, formaldehyde-free, and environmentally compliant with recyclable core options.Fabric wrapped panels shall be mounted using approved fixing system such as impalers, Z-clips, or adhesive as recommended by manufacturer. Fabric shall be tightly stretched over the entire panel including edges, properly wrapped and secured. Panels shall be carefully aligned and pressed into position ensuring uniform joints and seamless appearance. Installation may be horizontal or vertical as per architectural drawings.

13 Providing and fixing automatic sensor based urinal flushing system of approved make, including infrared sensor unit, solenoid valve, control box, power supply (battery/electrical), inlet connection, necessary fittings, fixtures, wiring, and making good the wall, complete in all respects as directed by Engineer-in-charge 11 No's 13014 143154

14 Vanity - Providing and fixing pre laminated , 18mm thick , vanity under wash basin with counter top, size 450mm x 800mm HT 1 No's 13110 13110

15 providing and fixing Hand Dryers 7 No's 21834 152838

16 providing and fixing Soap dispensers 7 No's 2860 20020

17 Providing and fixing concealed type dual flush cistern (3/6 litre capacity) of approved make, including heavy duty supporting frame (where required), flush plate, inlet and outlet connections, necessary fittings, fixtures, cutting and making good the wall, complete in all respects as directed by Engineer-in-charge 1 No's 10345 10345

18 GYPSUM COVE : Providing Gypsum cove of upto 18" wide with riser of 3", and 7" vertical. 67 RMT 1337 89579

19 GYPSUM PARTITION: Providing and fixing partition upto ceiling height 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum board conforming to IS: 2095: part I, consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher suitable for board as per manufacture’s specification and direction of engineer in charge all complete. Providing and fixing glass/Rock wool in partition of 50mm thick having density of 48 Kg per cum, all complete. 307

20 ALLUMINUM GLASS PARTITION 2400MM HT: Using Utra Slim line System glazings of 25mm x45 mm series in Black Matt Color ,, offering a robust solution for integrating Single Glazed Units (SGU) into 186 sqm 14747 2742942

your Interrior Partitions and Doors. These systems, typically comprised of 25mm x 45 mm Slime line series sectional elements, EPDM gaskets, and necessary fasteners,Metal glavanized brackets provide a comprehensive framework for securing glass panels in high traffic stability,we shall have proper installation, including the application of

sealant, is paramount to preventing glass to frame vibrations and ensuring the long-term performance of the system. This systems provide a sustainable and aesthetically pleasing method for utilizing 12mm Thick

Clear toughend SGU glasses in building envelopes.The aluminum Sections shall have special Black Powder coating. The Doors upto 900 x 2440 mm per panel/per leaf , makes the systems very perfect for Office

usage. ( WInd Load all structural calculations and certificates are clients scope.) For additional asthetic enhancement a segmnetations sytems is also used in accordance to architects design in striegth/ bend formations as needed . Note : All glass partions each panels shall not exceed 1500

mm in width and shall have intermediate Sections between each joints for stability . Almn framing Make shall be : Vantage brand/Polo ,Glass shall be Ashai/Saintgobain/ Modigaurd subject to availabilty at time of executions

21 TOUGHEN GLASS DOORS': Supply & Installtions of Glazed doors in Style Door : 35 x65 series using SGU 8mm clear Toughend Float glass ,with door Frame ,Open Door Closures ,450mm x 25mm Dia Q type handles with Dead Lock , incorporating HS (high strength) properties, necessitates careful -

consideration of supply chain logistics/Installations and Porlong usage

handling protocols.

22 BRICK MASONRY : 9 INCHES : Providing & constructing Brick masonry of 9" Thickness (half brick) with well burnt brick with Cement sand mortar in 1:4 ratio (only river sand to be used for mortar) in proper line, level & plumb. At every 1 Mtr. Ht. interval stiffener of Size: 100 x 100 mm (Min.) with 2 Bars of 8mm Tor Steel in Grade M20 grade Concrete (1:2:4) should be provided complete with proper line, level, plumb & curing. (Rate inclusive of all necessary tools, tackles, shuttering, propping, chisellng of existing floor & cleaning etc. Complete as per drawing details / Instructions by Design Team / site-incharge without stiffners) 38 SQM 6412 243656

23 PVC WALL PANELS : Providing and fixing PVC wall panels at waiting area , with backing of 8 mm thick wooden ply and wooden studds frames of 40*40 with equal spacing of 2400mm c/c fixed with gypsum screws on wall to level the wooden ply base backing, fixing the panels with silicone applications and metal clips to fill the joints , rates shall include all the required hardware for installation and finishing 38 SQM 11541 438558

24 Providing and fixing urinal partition made of toughened glass (10–12 mm thick) of approved make, size and shape, with polished edges, including SS brackets/clamps, necessary fixing accessories, drilling, and making good the wall, complete in all respects as directed by Engineer-in-charge 8 SQM 11680 93440

25 WASH BASIN: Providing and fixing counter top wash basin units in oval shape (concealed type wash basin as approved model and size) in approved colour 5 each 13873 69365

26 waste couplings 15 each 1430 21450

27 PILLAR COCK: Providing and fixing heavy duty Pillar cock of approved make all complete as per standard specifications and as directed by the Engineer-in-Charge including heavy duty C.P. Water connectors. (15 mm dia.) 5 each 5959 29795

28 Providing and fixing 5mm thick wall mirrors of size 450mm x 900mm HT , with all required hardware and fixing materials 5 each 12633 63165

29 Providing and fixing Towel / Tissue Holders 7 No's 3909 27363

30 Providing and fixing wall hung European type water closet of vitreous china of approved make, including heavy duty concealed frame system, concealed dual flush cistern, flush plate, soft close seat cover, all necessary inlet/outlet connections, waste pipe connection, bolts, nuts, and making good the wall and floor, complete in all respects as directed by Engineer-in-charge. 1 No's 31082 31082

31 Providing and fixing stainless steel kitchen sink of size : 450mm x 600mm (single bowl / double bowl) of approved make, of specified size and thickness (e.g., 1.0 mm), including waste coupling, plug, overflow arrangement, PVC waste pipe, bottle trap, necessary fittings, cutting and making good the countertop, complete in all respects as directed by Engineer-in-charge. 2 No's 8343 16686

32 BAFFLE CEILING: Providing and fixing. Metal baffle ceiling,90mm x120mm rectangular shape panels of wood grain, with approved finish @ 6inches c/c , hanging with L corner and suspended rod, Tolerence shall be -+ 20mm. 93 sqm 16671 1550403

33 WALL/ COLUMN PANELLING: Fabricating and fixing wall/column paneling to consist of 50mm x 25mm wooden Sections at spacing not exceeding 600mm bothways (horizontal and vertical). Paneling framework to be secured to wall surface/column surface. Paneling framework to be clad on one side with 12mm thick commercial ply finished with 1.0mm thk laminate finish. 47 sqm 8464 397808

34 Framing above glass partitions: for support with 50 X 50 MM wooden batten framing upto slab level including glass wool filling with single layer Gypsum board from both side 28 SQM 6412 179536

35 GRID CEILING : Supply & Installation of Gypsum grid tile 8mm thick (Size: 2'0" x 2'0") with India Gypsum grid ceiling with required steel frame section including all Complete as per drawing details / Instructions by Design Team / site-incharge. 32 sqm 3310.45 105934.4

36 METAL GRID CEILING : Supply & Installation of prepainted metal grid tile (Size: 2'0" x 2'0") with required steel frame section including all Complete as per drawing details / Instructions by Design Team / site-incharge. 75 sqm 2903 217725

37 STONE WORK: Providing and fixing of 12mm thick solid surface corian/Hynex on the plywoodboxing top with bevelled edges. Make of Merino/Samsung 12 sqm 12947 155364

38 FLUSH DOOR: Providing & Fixing 30mm Thk. Solid Core Commercial Flush Door with Wooden Beading as per drawing, finished with 1mm Approved Laminate (with Groove) finish on both sides of the door fixed with Approved adhesive, including necessary Edge Lipping Patti, 3 Nos. SS Hinges (Brushed finished), Brushed finished D Handle 250mm long with 3 Sets of keys, SS Door Stopper, Tower Bolt, Hand Polishing Etc. Complete as per drawing detail / instruction by Design Team / Site-incharge. Size: 2'6" x 6' 10" . Includes hardwood doorframe of 5"x 2.5".Hardware will be Dorset/Ozone/Hardwyn 6.4 sqm 28580.23 182913.49

39 50MM Aluminium skirting : Providing and fixing aluminium skirting of 50 mm height, made out of extruded aluminium sections of approved make and finish, including cutting, mitering at corners, and fixing to wall using appropriate fasteners, screws, and approved adhesive/anchors, complete with necessary accessories such as end caps, joints, and corner pieces, including surface preparation, alignment, and finishing, as per design and direction of Engineer-in-Charge 6.25 sqm 5578.35 34864.69

40 BOTTLE TRAP: Providing and fixing bottle trap manufactured in chromium plated with adjustable flange all complete as per standard specifications and as directed by the Engineer-in-charge. 15 No's 4175.45 62631.75

41 Providing and fixing chrome plated brass sink cock (pillar type / swivel spout / wall mounted) of approved make, including necessary connections, nuts, washers, fittings, and making good the wall or countertop, complete in all respects as directed by Engineer-in-charge 2 No's 4324.8 8649.6

42 CARPET TILE FLOORING: Providing and laying of Carpet Tile over the specified area with following specification. The floor which recieves the carpet to be thourougly cleaned as per manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing and clearing away of residual material to a location as directed. The measurements of carpet will be the actual laid area. 168 SQM 2044.15 343417.2

Sub Schedule-III DSR (electrical)

SL No Description Qty Unit Rate Amount DSR No.

1 Supplying, installing, testing and commissioning of following capacity End Feed Unit made of 1.6mm thick sheet steel enclosure duly painted with powder coating to existing rising mains complete with TPN disconnector FSU and HRC fuses, mounting stands, cable end box, brass compression gland, connections, earthing etc. as required.(200 amps TPN) 2 Each 25637 51274 DSREM 25 3.4.1

2 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 30KA, FPMCCB 1 Each 8127 8127 DSREM25 2.2.13

3 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

a) 16/20 Amp SP MCB - 2 Nos

b) 06/10 Amp SP MCB - 10 Nos

c) 06/10 Amp SP MCB - 12 Nos

Total 24 Each 285 6840 DSREM25 2.10.1

4 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

12 way (4 + 36), Double door 1 Each 13512 13512 DSREM25 2.5.3

5 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 A 4P MCB 2 Nos 1115 2230 DSREM25 2.13.2

6 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

32 A SP MCB -6 Nos 6 Each 285 1710 DSREM25 2.10.1

7 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (4 + 12), Double door 1 Each 7951 7951 DSREM25 2.5.1

8 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way (4 + 18), Double door 2 Each 5299 10598 DSREM25 2.4.2

9 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 amps 2 Each 3452 6904 DSREM22 2.15.2

10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

16 A SP MCB -18 No. 36 Each 285 10260 DSREM25 2.10.1

11 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door 4 Each 4377 17508 DSREM25 2.4.1

12 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

16 A SP MCB -12 No. 48 Each 285 13680 DSREM25 2.10.1

13 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 amps 12 Each 3452 41424 DSREM25 2.15.2

14 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2 + 12 way/18 way, Double door 4 Each 3367 13468 DSREM25 2.3.4

15 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

16 A SP MCB -14 No. 56 Each 285 15960 DSREM25 2.10.1

16 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Double pole 4 Each 696 2784 DSREM25 2.10.3

17 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2 + 12 way, Double door 2 Each 3367 6734 DSREM25 2.3.4

18 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

16 A SP MCB -16 No. 16 Each 285 4560 DSREM25 2.10.1

19 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

32A Double pole 2 Each 696 1392 DSREM25 2.10.3

20 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2 + 8 way, Double door 2 Each 2871 5742 DSREM25 2.3.3

21 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

16 A SP MCB -4 No. 8 Each 285 2280 DSREM25 2.10.1

22 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Double pole 2 Each 696 1392 DSREM25 2.10.3

23 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

a) Primary Light Point. 77 Point 1704 131208 DSREM25 1.10.3

b) Secondary Light Point. 154 Point 1362 209748 DSREM25 1.10.2

24 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Bell Point 10 Point 1704 17040 DSREM25 1.10.3

25 Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 1200 Mtr 267 320400 DSREM25 1.14.1

b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 1550 Mtr 311 482050 DSREM25 1.14.2

c) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 500 Mtr 373 186500 DSREM25 1.14.3

26 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

27 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

28 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

a) Upto 35 sq. mm 435 Mtr 47 20445 DSREM 25 10.5.1

b) Above 95 sq. mm and upto 185 sq. mm 60 Mtr 97 5820 DSREM 25 10.5.3

29 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required. 2 set 8351 16702 DSREM 25 5.4

30 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required. 2 set 15004 30008 DSREM 25 5.6

31 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 50 Mtr 160 8000 DSREM 25 5.9

32 Supplying, Installation, Testing & Commissioning of 1 Each 863788 863788 DSREM 25 29.1.7

‘Silent Type Diesel Generating set as per CPCB IV +

or better norms along with having Prime Power Rating

of KVA as below, 415 volts at 1500 RPM, 0.8 lagging

power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, ncluding testing at factory and site with fuel, load for test and other

necessary arrangements Complete as per CPWD

specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of

manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:(A) Diesel Engine:

Tourbo charged Diesel engine 4 stroke water cooled,

multi cylinder, dynamically balanced fly wheel, electric

start of suitable BHP at 1500 RPM suitable for above

output of alternator at 40 0C, 50% RH & at 1000 Meter

MSL , capable of taking 10% over loading for one hour

after 12 hours of continuous operation. The engine will

be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the Electronic governor shall be as per

ISO 8528.The engine shall comply to the latest CPCB

norms (CPCB IV + or better) and Conforming to BS

per CPWD specifications. (B) Engine mounted Instrument Panel fitted with and having digital dis Plate for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(x) Fuel Level (C) Alternator:

Synchronous alternator rated of appropriate KVA, 415

volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8

lagging power factor at 40 0C, 50% RH & at 1000

Meter MSL. The alternator shall be having Screen

Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically balanced rotor, capable of taking 10% over loading for one hour after 12 hours of continuous operation, self

cooled,self-excited and self-regulated through AVR

conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for tropical conditions and with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of

manufacturer (E) FUEL TANK: Daily service fuel tank of suitable liters capacity as per CPWD Specifications, fabricated out of 3 mm thick

M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class ‘C’ pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust

silencer and catalytic convertor.

(G) Starting System:

12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable numbers of batteries

(180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside

the acoustic enclosure of DG Set. (H) Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere and the temperature rise inside the enclosure, noise level outside enclosure. The acoustic enclosure should be suitable for cable connection/connection through bus-trunking. Such arrangements on acoustic enclosure should be water proof & dust-proof conforming to IP-65 protection. Theen closure shall be as per CPCB IV + or better norms etc. and as per CPWD specifications. (I) AMF Panel: Free standing floor mounted IP 42 automatic mains failure control panel including auto by-pass, suitable for KVA as below for silent type DG set complete with relays, timers, set of CTs for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor, KWH, Kilo Volt

Ampere Reative Hour (KVARH), KVA (Phase & Total),KW & provision for overload, short circuit, restricted earth fault, under frequency, power (aluminium) and control (copper ) cabling of suitable size upto 15 meter

between AMF panel, LT Panel and DG Set including connection interconnection etc. as required, all complete and inter locking and communication/Ethernet /RS485/SNMP port open protocol for BMS

integration including suitable software, the panel shall be of DG Set OEM make etc. as per approved byEngineering in charge and including the following: 1. Suitable numbers and appropriate capacity 4 pole motorised electrically operated draw out with cradle type 3 position ACB/ MCCB with electronic release for

O/C & E/F and shunt trip.

2. Auto/Manual/Test/Off selector switch

3. Protection for under and over voltage phase

reversal (2 nos Over voltage relay, 2 Nos. reverse

power relay and 2 Nos. under voltage relay).

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( LN & L_L), kW, kVA (Phase & Total), Frequency, KWH,

6. LED Indicating lamps for load on mains and load on set7. Fuse/ MCB for instruments

8. Battery charger, complete withtransformer/ rectifier, D.C. voltmeter and ammeter, selector switch for

trickle, off and boost and current adjustment.

9. Main supply failure monitor

10. Supply failure timer

11. Restoration timer

12. Control unit with three impulse automatic engine

start/stop and failure to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC

sensing, Over Current, Unbalancing load with suitable

number of relays and accessories

17. Maintenance notification based on Engine Run

Hour & due date 18. Load Management through PLC to achieve auto

opening and closing of incomer breakers, bus coupler switching of essential panel , interlocking providing

signal to AMF Panel for load status and AMF shall

give command to DG Set to auto start / auto stop

depending upon load status and requirement etc. and necessary hardware and software required to perform the operation shall be provided by the contractor including all control wiring.

Sub Schedule IV MR(electrical)

SL No Description Qty Unit Rate Amount

1 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 3 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 16 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Providing 16A switch + 3 Nos 6A 3 Pin SKT 310 Each 868 269080

2 Supplying and fixing 32 to 63A, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

c) 63A DP 6 Each 1251 7506

d) 32A DP 6 Each 1001 6006

3 Supply & testing of XLPE insulated aluminium conductor steel armoured power cable of 1.1 KV grade confirming to IS :7089 (part 1) 1988 or latest amendment and as per instructions of official-in-charge.

b) 4 X 25 sq. mm 75 Meter 343 25725

4 Supply & testing of XLPE insulated copper conductor steel armoured power cable of 1.1 KV grade confirming to IS :7089 (part 1) 1988 or latest amendment. and as per instructions of official-in-charge.

b) 3 x 4.0 sq. mm 50 Meter 422 21100

5 Supplying and drawing following sizes of FRLS PVC insulated copper flexible cable 16,10,6,4,2.5 sq.mm cable of length 60,60,150,60,70 meters respectively, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

16,10,6,4,2.5 sq.mm cable of length 60,60,150,60,70 meters respectively 1 meter 66698 66698

6 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5x150 sq.mm.(2 nos) ,4x25 sq.mm. (8 nos),4x10 sq.mm. (10 nos), 4x6 sq.mm.(16 nos),3x4 sq.mm. (16 nos),3x2.5 sq.mm. (25 nos),termination of 16 sq.mm. (20 nos),6 sq.mm.,4 sq.mm.,2.5 sq.mm. (34 nos) 1 meter 14107 14107

7 Supply and testing of LED Flood light fixture with following wattage rating and as per technical specifications attached, including accessories for support on wall, bracket, truss, or suitable hanging arrangement upto 1 meters, and 1 meter FR PVC insulated copper conductor flexible cable of size 1.5 sq. mm, complete as per instructions of official-in-charge.

a) Providing of ceiling lights , recessed 15 W , round lights of 160mm dia, IP20. 120 Each 1270 152400

b) Providing of Linear lights , suspended from ceiling, 36-72W , L: 4ftx1ft, Aluminium body in black colour, IP20 .High Power Factor >0.97,Color Temperature: 6K, 4K, 3K premium light 48 Each 8883 426384

c) Providing of Linear lights , suspended from ceiling, 30W , L: 1200mm x 2100mm, Aluminium body in black colour, IP20 . 1 Each 4758 4758

d) Providing of Linear lights , suspended from ceiling, 30W , L: 900mm, Aluminium body in black colour, IP20 . 9 Each 4365 39285

e) Providing of Ripple suspended lights, 25W, Dia :600mm, Aluminium body black in colour, IP20 24 Each 12717 305208

f) Providing of Ribbon suspended lights 30W/Mtrs , L: 23 MTR 2 Each 105326 210652

g) Providing of Ribbon suspended lights 30W/Mtrs , L: 20 MTR 1 Each 91621 91621

h) Providing of 600mm x 600mm , ceiling panel lights, aluminium body in white colour . 24 Each 2405 57720

i) Providing of Suspended cylindrical down lights COB with aluminium body and die casted heat sink. 12W, 26 Each 3650 94900

j) Providing of Ding Dong Bell 10 Each 546 5460

k) Providing of Wall Fan. 45 Each 3777 169965

l) Providing of 7” Dia Exhaust Fan with Louvers. 13 Each 2076 26988

8 Installation and commissioning of LED lighting fixture of any wattage rating upto the below mentioned height, including connections, complete as per instructions of official-in-charge.

Above 3 meters and upto 6 meters 323 Meter 282 91086

9 Providing and Fixing of Main Panel board Comprising of the following :

Supply and installation of main LT panel, wall mounted front operated totally enclosed vermin proof, indoor non-drawout-cubicle type power panel fabricated out of 2mm thk CRCA sheet having gasketed hinged cover on each cubicle fully powder coated after 7 Tank treatment, incorporating horizontal and vertical sleeved copper busbars, complete with all internal wiring, danger board, 2 earthing legs, cable chamber etc as required, housing below mentioned switch gears / meter ( GA drawing of the panel got to be approved by Bank / Architect for fabricate the same.)

1No.,200A,FP, Changeover Switch + 1 no. , 200A,TP, MCCB with ELR(0-3A) and CBCT as Incomer

4 nos. 40A & 63A 14 nos. TPN, MCB outgoing

1 no., 0-200A, Ammeter with CTand selector switch

1no., 0-500V, Voltmeter with selector switch and fuse

1Set, TPN, Copper busbars of size 35mm x 5mm thk PVC insulated suitable for 250 Amp load

1 Set, RYB, indicating lamps with resistors and fuses

Full Set as above 1 Set 386336 386336

SCHEDULE V- VRV/VRF Air Conditioning System work

SN DESCRIPTION Qty. Unit Rate Amount

1 Supply, installation, testing and commissioning VRF Condensing (Outdoor) Units

Floor mounted self contained packaged variable capacity air cooled condensing unit, complete with hermetically sealed compressors, condenser coils, fans, control panel, microprocessor controller, etc. as per

enclosed technical specifications.

Supply, installation, testing and commissioning of following VRF Connected Condensing/Outdoor units with Factory Precharged R-410a ecofriendly refrigerant, complete with 100% inverter scroll Compressors , Inverter driven Condesner Fan motor , Condenser in copper with Al. Fins , Complete with necessary electrical and Mechanical protections. Contractor to make sure that the selected units are capable of delivering the Capacity given at 43 Deg. Ambient Conditions with Continuous cooling at 56 Deg. with COP of 4.4 and IPLV rating of 7.0. The minimum Energy Efficiency Ratio shall be as per ASHRAE STANDARDS 90.1 -2001 table 6.2.1B. The condensing units shall be suitable for operation on 415 ± 10% volts, 50Hz, 3 phase, 50Hz AC power supply and the condensing units shall be of following capacities:

Refrigerant : R 410

Propose Makes: Daikin, Mitsubishi

Cooling Capacity : 56 HP ( Top Discharge)

Configuration: 2x28HP

Cooling Capacity : 28 HP Top Discharge

Configuration: 1x28HP

Cooling Capacity: 4HP Side Discharge

Configuration: 1x4HP

2 Supply, installation, testing and commissioning VRF Evaporating (Indoor) Units

Complete (SITC) with single phase low-noise centrifugal fan, cooling coil, filter, linear electronic expansion valve, drain pump and

electronic control unit. Proposed make - Daikin, Mitsubishi

2.1 Ceiling Cassette- Four Way Type

Capacity: 2.8 TR 4 Nos. 69906 279624

Capacity: 2.0 TR 22 Nos. 61850 1360700

Capacity: 1.7 TR 4 Nos. 61106 244424

2.2 High Wall Split AC Units

Capacity: 1.0TR 4 Nos. 26153 104612

Capacity: 2.0 TR 2 Nos. 33962 67924

Capacity: 1.3TR 2 Nos. 29623 59246

Capacity: 0.8TR 2 Nos. 26153 52306

2.3 Mid Static Ductable Split AC Units

Capacity: 2.5TR 2 Nos. 48339 96678

2.5 Supply, installation, testing and commissioning Cordless Remote Control Unit for Ceiling Cassette and Highwall Split AC Units 42 Nos. 2169 91098

2,6 Supply, installation, testing and commissioning Chorded Remote for Ductable Split AC Units 3 Nos. 4338 13014

3 Supply, installation, testing and commissioning `Y' Joints For Refrigerant Piping 42 Nos. 9296 390432

4 Supply, installation, testing and commissioning CENTRAL REMOTE CONTROLLER 1 No. 105355 105355

Central Electronic Remote controller, including necessary software, connected to a PC in control room for operating, monitoring, setting and controlling of all

indoor and outdoor units of the VRF system.

The controller shall be capable of the following minimum functions:

i) Run status of each IDU.

ii) Temperature setting of the individual IDU's

iii) Indication of actual temp. in the room at particular time.

iv) Switching the indoors units on/off from front desk

v) Communication with ODU

microprocessor to share the complete data of the ODUs.

5 Supply, installation, testing and commissioning Refrigerant Piping For VRF System

Hard drawn copper piping in brazed construciton, complete with 19mm insulation, supports/suspenders.

Refrigerant Piping For Suction Gas and Liquid 540 M 2417 1305180

Approved Makes: Maxflow,Indigo,parasmani

6.1 Control Cabling from Indoor to Outdoor units

Supply, installation, testing, and commissioning of control cum transmission wiring between ODU & IDU including PVC conduites.

2 core x 0.75 sq.mm Cu. Shielded Cable 650 M. 279 181350

Approved Makes:Polycab,Havells,Anchor

6.2 Supply, installation, testing, and commissioning Communication Cable from Central Controller to the ODU's, and data cable from controller to PC. 175 M. 248 43400

2 core x 1 sq.mm Cu.

Approved Makes:Polycab,Havells,Anchor

7 Supply, installation, testing, and commissioning Drain Piping

Rigid PVC piping insulated with 6mm thick nitrile rubber foam insulation.

Rigid PVC piping insulated with 6mm thick nitrile rubber foam insulation.

Made out of 40 NB 6 Kg class rigid PVC pipe, including all necessary fittings, with solvent-cement leak tight joints, and "tees"

for connections to branches from units.

Approved MakesPrince,Astral,Supreme

8 Supply, Installation , Testing and Commissioning of drain Pumps for Highwall Split AC Units 2 Nos 15493 30986

Approved Makes:Prince,Astral,Supreme

9 Supply, Installation, Testing and Commissioning of Dual Timer with relays 1 Nos 9296 9296

for server room

Approved Ma/kes: Smart ElectronicsMighty mounts/ Blue Diamonds

10 Supply, installation, testing and commissioning charges towards Installation of Fresh Air Fans of follwing CFM

Approved Makes: caryaire, Crompton ,Havells

11 Supply, installation, testing and commissioningof Rectangular Ducting of 24G for Fresh Air with clamp supports etc. 665 Sqft 186 123690

Approved Makes:Jsw,Tata,Vizag Steel/SAIL

12 Supply, installation, testing and commissioning of Nitrile Rubber Insulation -6 mm thick 685 Sqft 93 63705

Approved Makes:K-flex,Arma Flex,Duro

Supply & Installation of Oval Ducting for Ductable AC of 24G 750 Sqft 279 209250

Approved Makes:Jsw,Tata,Vizag Steel/SAIL

13 Supply, installation, testing and commissioning of Nitrile Rubber Insulation -13 mm thick 750 Sqft 110 82500

Approved Makes:K-flex,Arma Flex,Duro

14 Supply, installation, testing and commissioning of Acoustic insulation for Supply air duct with the thickness of 10mm self adhesive. For Supply air mouth piece up to 1.5 Mtr distance. 95 Sqft 118 11210

Approved Makes:K-flex,Arma Flex,Duro

15 Supply, installation, testing and commissioning of Flexible Ducting Dia 100mm 16 M 1549 24784

UPTWIGA/SUPREAME/Thermaflex

16 Supply, installation, testing and commissioning of fire rated Canvass Connection for Fresh Air Fan 8 Nos 9296 74368

17 Supply, installation, testing and commissioning of Canvass Connection for Ductable unit 3 Nos 11775 35325

18 Supply, installation, testing, and commissioning Round Diffuser with Butterfly Damper 200 Dia 15 No 3532 52980

Approved Makes: Airpro/Caryaire/Unique/Cosmos

19 Supply, installation, testing, and commissioning GI Cable Tray of following sizes:

19.1 300 mm width X 50 mm depth X 1.6 mm thickness 60 M 1177 70620

19.2 150 mm width X 50 mm depth X 1.6 mm thickness 25 M 930 23250

Approved Makes:Jsw,Tata,Vizag Steel/SAIL

20 Supply, installation, testing, and commissioning Fabrication of Outdoor Unit Platform for VRV 4 No 15493 61972

21 Supply, installation, testing, and commissioning Earthing work for all equipments 1 Lot 30987 30987

Earthing near ODU shall be provided by client and from MCB to ODU Unit Earthing shall be provided by bidder.

22 Core Cutting of required size for Copper Pipes and Drain Pipes 1 Lot 11918 11918

Total Amount Basic 8168290

SCHEDULE – VI Audio Visual/ELV Works

SL No Description Qty Unit Rate Amount

Conference Room (11458 x 7487)

1 Supply, Installation, Testing & Commissioning of 2-way, Ceiling-mount loudspeaker. Frequency range - 70 Hz to 16kHz, Rated RMS Power - 16Watts or better, Sensitivity-89 dB SPL or better, Coverage Angle- 90-140° conical or better, Maximum SPL Continuous/Peak-101dB/107dB or better, Rated Impedance - 8 Ohms. Transformer Tapping - 70V/100V(16, 8, 4, 2, 1 watts) or better. Transducer - 4-inch or better, Material - Painted ABS polymer Baffle and Power coated steel grille or better. Safety rating - UL1480, UL2043. Mounting rails and C-Ring for ceiling tile included. 8 Nos 16852 134816

2 Supply, Installation, Testing & Commissioning of Quad Channel Class-D amplifier. Per Channel Power 60W @8Ω/4Ω/70V/100V or better. Frequency Response- 20 Hz – 20 kHz or better. Signal to Noise ratio: 100 dB or better, Input impedance:10k, balanced or unbalanced or better, Highpass filter: 80 Hz in Bridged 70 V & 100 V, Front and Rear panel indicators for Power, signal (per channel), limit / mute / protect etc. or better. Better to have Remote standby and Power saving features - Auto-standby. 1 Nos 154934 154934

3 Supply, Installation, Testing & Commissioning of Open Architecture Digital Signal Processor with 4 Mic/Line Input with Phantom Power and 4 Line Outputs. GPIO Ports - 8x8 or better. AECchannels - 8 or more with 200ms tail length.Minimum 8x8 Dante channels and support for up to 64x64 Network audio channels via Dante /AES67 or similar protocol. SIP Softphone integration for Audio conferencing. USB-B & C port supporting AV USB Bridging for software or web-based conferencing applications emulating USB Audio (Speakerphone) and USB Video (Camera) driver. 24 bit-A/D-D/A converters or better, 48 kHz Sample rate or better, Input frequency response of 20 Hz to 20 kHz or better, Input dynamic range > 108 dB or better. RS232 Ports - 1 or more. 1 Nos 481487 481487

4 Supply of Table Top Chairman Unit should have a built-in DSP chip which can adjust the audio output and sensitivity automatically and support Cat5/6 cabling in flexible way through daisy-chain, ring, tree or star modes and with push to talk button, pluggable gooseneck microphone easy to remove when not in use and with light ring for easy identification of the speaker. Chairman unit has the highest priority to speak and control delegate unit s speaking status Gooseneck microphone Stem length: 48/56cm. The electric gooseneck microphone is equipped with a LED indicator ring and able to avoid the interference of electromagnetic from cell phones. Microphone should get auto off when not in use and also get auto activated when someone starts to speak. Equipped with digital coding Each unit s ID number and the identity of delegate can be instantly set by the main control unit or OEM graphical software. Product should be CE and FCC, Certified . Technical Parameters :Frequency Response: 100 Hz – 16 kHz Sensitivity: ≥ -50 dB 1 Nos 45139 45139

Signal-to-Noise Ratio: ≥ 70 dB Auto Gain Control (AGC): -45 dB to 0 dB Total Harmonic Distortion (THD): ≤ 0.1%Connectivity: 2 × RJ-45 ports

5 Supply of Table Top Delegate Unit should have a built-in DSP chip which can adjust the audio output and sensitivity automatically and support Cat5/6 cabling in flexible way through daisy-chain, ring, tree or star modes and with push to talk button, pluggable gooseneck microphone easy to remove when not in use and with light ring for easy identification of the speaker.Gooseneck microphone Stem length: 48/56cm. The electric gooseneck microphone is equipped with a LED indicator ring and able to avoid the interference of electromagnetic from cell phones. Microphone should get auto off when not in use and also get auto activated when someone starts to speak. Equipped with digital coding Each unit s ID number and the identity of delegate can be instantly set by the main control unit or OEM graphical software. Product should be CE and FCC, Certified . Technical Specification:- Frequency response : 100HZ~16KHZ 16 Nos 38519 616304

Sensitivity : ≧-50dB

S/N ratio : ≧70dB

Auto Gain Control (AGC) -45 0dB T.H.D : ≤ 0.1% Connections RJ-45 Jack x 2

6 Supply of Conference Control Unit should be capable of managing a minimum of 9 chairman units and up to 500 delegate units using extension power supplies. The system must support PTZ control for 12 or more cameras to enable the “Look at Me” feature for automatic camera tracking. The control unit should feature a 128x64 pixels digital LCD display for configuration and status monitoring. It must include an auto self-testing function on power-up. The system should also support voting functions and a graphical user interface (GUI) for simplified operation. 1 Nos 337643 337643

The product should be CE and FCC certified.

Technical Specifications:

• Frequency Response: 50 Hz ~ 16 kHz (±1 dBV)

• Total Harmonic Distortion (THD): ≤ 0.1%

• Signal-to-Noise Ratio (S/N): ≥ 85 dB

• AUX Output: RCA jack (balanced)

• AUX Input: AUX 1 (RCA)

• Microphone Outputs: 4 Zone individual outputs dedicated to microphone units for 4 zone amplifiers.

• USB Port (Type A): Supports PC audio recording and soft video conferencing (VC)

• Network Control: TCP/IP protocol via wired or wireless network using PC or mobile devices

• Control Interfaces: RS-232, RS-485 (D+, D–), and LAN port for programming and system control

• Microphone Connectivity: CAT5e cable with 4 sets of RJ-45 ports

• Ethernet Technology: 10 Mbps Ethernet

7 Supply of of 4 ports of RJ45 connectors. Two screw holes for fixing on the table. Effectively decrease the length of using cables and increase the cabling flexibility. Should be same OEM of conference system. 2 Nos 3017 6034

8 Supply of 2.5 meters of Cat6/Cat5e LAN-Patch cable, featuring 8 x 0.14 mm2 gauge wires. Equipped with RJ45 metallic connectors and accompanying protective boots, ensuring reliable connectivity and optimal performance. Includes all necessary company-fitted standard accessories for seamless integration. Should be same OEM of conference system. 17 Nos 945 16065

9 Supply of 10 meters of Cat6/Cat5e LAN-Patch cable, featuring 8 x 0.14 mm2 gauge wires. Equipped with RJ45 metallic connectors and accompanying protective boots, ensuring reliable connectivity and optimal performance. Includes all necessary company-fitted standard accessories for seamless integration. Should be same OEM of conference system. 2 Nos 4223 8446

10 Supply of 20 meters of Cat6/Cat5e LAN-Patch cable, featuring 8 x 0.14 mm2 gauge wires. Equipped with RJ45 metallic connectors and accompanying protective boots, ensuring reliable connectivity and optimal performance. Includes all necessary company-fitted standard accessories for seamless integration. Should be same OEM of conference system. 2 Nos 6703 13406

11 Supply, Installation, testing and commissioning of Dual Channel Dynamic Wireless Handheld Microphone with Frequency response of 80-14000 Hz; Operating time: approx. 10 hours; Input sensitivity (capsule): 1.5 mV/Pa, Pick-up pattern: Cardioid; Adjustment range of transmitter sensitivity of 0 to -30 dB, adjustable in 10 dB steps; with Dual Rack receiver Diversity principle: Antenna switching diversity via internal antennas; frequency response: 50 – 16,000 Hz (-3 dB); Audio adjustment range: 45 dB, adjustable in 5 dB steps; Line/Mic level: 20 dB, switchable 1 Nos 98923 98923

12 Supply, Installation, testing and commissioning of 98 inch Display with Resolution of 4K (3840x2160) Or Better; Brightness(Typ.): 450 nit or Better; Contrast Ratio (Typ.): 5000:1 or Better; Operation Hour:16/7 or Better; Auto Source Switching & Recovery, Button Lock, Hot key option, Plug&Play with Wall Mounting Bracket 1 Nos 598277 598277

13 Supply, Installation, testing and commissioning of 55 inch Display with Resolution of 4K (3840x2160)or more ; Brightness(Typ.): 300 nit or more; Wall Mounting Bracket; Operation Hour:16/7; 2 Nos 91491 182982

14 Supply, Installation, testing and commissioning of HDMI USB 3x3 switch with 3 HDMI and 1 USB-C input and 3 HDMI output.When switching between the USB-C input or HDMI + USB-B input, the peripheral devices connected to 2 x USB-A should switch between the inputs.Complete Plug and Play, NO additional driver or software required to be recognized by the computer.USB-C supports ALT-DP video, data and power charging to 60 watts.Built-in EDID management.Supports HDMI 2.0 and HDCP 2.2.Balanced analog audio for audio de-embedding. The USB 3.2 Gen1 USB Type C cable is required for USB-C connectivity.This switcher supports video resolutions up to 4Kx2K@60Hz 4:4:4, HDR, and multichannel audio. The switch should support RS-232, CEC, Digital I/O, Contact Closure, and Ethernet control Protocols. 1 Nos 119236 119236

15 Supply, Installation, testing and commissioning of Cable Cubby with 1x HDMI Port, 1x USB Port, 1 x RJ45, 2 x Power Socket 2 Nos 18056 36112

16 Supply, Installation, testing and commissioning of Full HD 1080p @ 60 frames per second PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57 deg, min 255 Presets.Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI & USB 3.0, Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~ +170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be minimum 200° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual USB Driver.Camera can be controlled and managed through centralised software on network. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports. 1 Nos 382716 382716

17 Supply of camera wall mount metal stand. It should be constructed with durable material and can be attached right side up or upside down, depending on camera configuration and requirment. OEM accessory will give a perfect fit and features pre-drilled installation hardware and cable holes. 1 Nos 6500 6500

18 Supply, Installation, testing and commissioning of 11-inch Touch Display with Resolution of 2360x1640; 500 nits of brightness; USB-C Charging 1 Nos 52790 52790

19 Supply, Installation, testing and commissioning of 24 Port POE Network Switch 1 Nos 48964 48964

20 Supply, Installation, Testing and Commissioning of Dual Band Wi-Fi router/Access point 1 Nos 26482 26482

21 Supply, Installation,Testing & Commissioning of 15 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. 1 Nos 30093 30093

22 Supply, Installation,Testing & Commissioning of Cable, Connector & Accesoories As per Requirement 1 Lot 140835 140835

Total(A) 3538184

RM Cabin (6600 x 3820)

1 Supply, Installation, testing and commissioning of 65-inch Interative Display with Resolution of 4K (3840x2160)or more ; Brightness(Typ.): 400 nit or more; Contrast Ratio (Typ.): 1200:1; Viewing Angle (H/V)- 178:178; Touch Response Time: 5ms or less; Built-in Speaker (15W X 2CH); Key features: Powered by Android™ and EDLA Certification, Split Note mode, Quick access controls, Device management solution with Wall Mount Bracket 1 Nos 150465 150465

2 Supply, Installation, testing and commissioning of wall plate extends USB-C data and DP Alt Mode AV up to 70M converting to HDMI & USB-A at the receiver, 2x USB-A client hub on wall plate allows for easy connections of USB peripherals such as USB Mic's, keyboard/mouse, & document cameras, 1 Nos 30093 30093

3 Supply, Installation, Testing & Commissioning of Cable, Connector & Accesories As per Requirement 1 Lot 60186 60186

Total(B) 240744

Ante Room (6600 x 3820)

1 Supply, Installation, testing and commissioning of 55 inch Display with Resolution of 4K (3840x2160)or more ; Brightness(Typ.): 300 nit or more; Wall Mounting Bracket; Operation Hour:16/7; Wall Mounting Bracket 1 Nos 91407 91407

2 Supply, Installation, testing and commissioning of All-in-one standalone USB-based plug-and-play system integrating a 4K PTZ camera, microphone array, and speaker, designed for seamless compatibility with software-based video conferencing platforms. The camera shall feature a Sony 4K True WDR sensor with resolution support up to 4K at 30fps and 1080p at 60fps, and a minimum field of view of 92°, with True WDR up to 120 dB for superior backlight compensation in high-contrast environments. The system must support intelligent features including speaker tracking, auto framing, presentation tracking, smart gallery, gesture control, audio fence, and people counting API. It shall provide a minimum of 3X optical zoom, 5X digital zoom, and 15X total zoom, along with at least 10 camera presets via remote control. The audio system shall include stereo speakers with minimum 12W output and up to 96 dB SPL at 0.5 meters, and a minimum of 10 beamforming microphones with at least 8-meter pickup range, supporting echo cancellation and noise suppression. The device shall allow expansion via external microphones or speakerphones with minimum 10-meter cable support and include 3.5mm audio I/O for BYOD speakerphone functionality. It shall support HDMI display output for screen projection via a single USB connection and provide control via remote and OEM-native applications for Windows and macOS. A free centralized management software from the OEM shall be provided for remote firmware upgrades, camera control, and network-based configuration. The system shall support recording and streaming via native application to platforms such as YouTube and Ubicast, and must be compatible with all major video conferencing applications with certifications for Microsoft Teams and Zoom. 1 Nos 210651 210651

3 Supply, Installation, testing and commissioning of wall plate extends USB-C data and DP Alt Mode AV up to 70M converting to HDMI & USB-A at the receiver, 2x USB-A client hub on wall plate allows for easy connections of USB peripherals such as USB Mic's, keyboard/mouse, & document cameras, 1 Nos 30093 30093

4 Supply, Installation, testing and commissioning of 8 Port Network Switch 1 Nos 21328 21328

5 PC/ Laptop (Client Scope) 1 Nos 114353 114353

6 Supply, Installation,Testing & Commissioning of Cable, Connector & Accesoories As per Requirement 1 Lot 60186 60186

Total(C) 528018

Grand Total(A+B+C) 4306946