Providing the additional room at First Floor with attached toilet, walking track in rear lawn, Gazebo in real lawn, car shed in front lawn and conversion of garage in camp office in House No. 20 Type 6 Sector 7 Chandigarh IBM Scheme No. W4/2025/25361

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m DSR 2.10

All kinds of soil. DSR 2.10.1

Pipes, cables etc. not exceeding 80 mm dia. DSR 2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level DSR 4.1

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) DSR 4.1.3

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : DSR 6.4

Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.4.1

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. DSR 6.13

Cement mortar 1:4 (1 cement :4 coarse sand) DSR 6.13.2

12 mm cement plaster finished with a floating coat of neat cement of mix :DSR 13.7

1:4 (1 cement: 4 fine sand)DSR 13.7.2

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

W.C. pan with ISI marked white solid plastic seat and lid. DSR 17.3.1

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: DSR 17.7

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.3

Providing and fixing white vitreous china water closet squatting pan (Indian type) : DSR 17.13

Orissa pattern W.C. pan of size 580x440 mm DSR 17.13.2

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. DSR 17.19

10 litre (full flush) capacity-white DSR 17.19.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings as DSR 17.28

32 mm dia : DSR 17.28.1.1

Providing and fixing soil, waste and vent pipes :DSR 17.35.1

100 mm dia DSR 17.35.1

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 DSR 17.35.1.2

75mm diameter : DSR 17.35.2

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 DSR 17.35.2.2

Providing and fixing plain bend of required degree DSR 17.39

100 mm dia DSR 17.39.1

Sand cast iron S&S as per IS : 3989 DSR 17.39.1.2

75 mm dia DSR 17.39.2

Sand cast iron S&S as per IS - 3989 DSR 17.39.2.2

Providing and fixing heel rest sanitary bend DSR 17.40

100 mm dia DSR 17.40.1

Sand cast iron S&S as per IS - 3989 DSR 17.40.1.2

75mm diameter :DSR 17.40.2

Sand cast iron S&S as per IS - 3989 DSR 17.40.2.2

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. DSR 17.43

100x100x100 mm DSR 17.43.1

Sand cast iron S&S as per IS - 3989 DSR 17.43.1.2

75x75x75 mm DSR 17.43.2

Sand cast iron S&S as per IS - 3989 DSR 17.43.2.2

Providing and fixing single equal plain junction of required degree :DSR 17.44

100 mm DSR 17.44.1

Sand cast iron S&S as per IS - 3989 DSR 17.44.1.2

75 mm DSR 17.44.2

Sand cast iron S&S as per IS - 3989 DSR 17.44.2.2

Providing and fixing terminal guard: DSR 17.56

100 mm DSR 17.56.1

Sand cast iron S&S as per IS - 3989 DSR 17.56.1.2

75 mm DSR 17.56.2

Sand cast iron S&S as per IS - 3989 DSR 17.56.2.2

Providing and fixing collar : DSR 17.57

100 mm DSR 17.57.1

Sand cast iron S&S as per IS - 3989 DSR 17.57.1.2

75 mm DSR 17.57.2

Sand cast iron S&S as per IS - 3989 DSR 17.57.2.2

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, incl. cost of cutting and making good the walls and floors. DSR 17.60

100 mm inlet and 75 mm outlet DSR 17.60.2

Sand Cast Iron S&S as per IS- 3989 DSR17.60.2.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. : DSR 18.10

Internal Work - Exposed on Wall

15 mm dia. nominal bore : DSR 18.10.1

20 mm dia. nominal bore : DSR 18.10.2

Providing and fixing of forged brass / GM Gate Valve

size 20mm i/d DSR 18.17.1A

Providing and fixing uplasticised PVC connection pipe with brass unions : DSR 18.21

45 cm length : DSR 18.21.2

15 mm nominal bore : DSR 18.21.2.1

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : DSR 18.46

15 mm nominal bore : DSR 18.46.1

20 mm nominal bore : DSR 18.46.2

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR 18.48

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 DSR 18.49

15 mm nominal bore. DSR 18.49.1

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. DSR 18.51.1

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.DSR 18.52.

15 mm nominal bore DSR 18.52.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points ... DSR 18.53

15 mm nominal bore. DSR 18.53.1

Providing and fixing of C.P. Brass Extension Nipple Size 15 mm x 50 mm of approved make and quality as per direction of EIC DSR 18.53A

Cutting holes up to 30x30 cm in walls including making good the same: DSR 18.76

With F.P.S. bricks : DSR 18.76.1

Cutting holes up to 15 x 15 cm in R.C.C. floor and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 including finishing complete so as to make it leak proof . DSR 18.77

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.: DSR 18.78

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: DSR 19.4

100x100 mm size P type DSR 19.4.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.4.1.1

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen Sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required of Size 27" x 21" x 8" of approved make

Providing and fixing of looking glass with PVC beeding 1/4" with plastic hard board complete in all respect of approved make

Providing and fixing of C.P. Steel Grating Heavy (With hole without hole) size 4" i/d of approved make

Providing and fixing of Wall hung wash basin with full pedestal complete with C.I./MS brackets 32mm C.P. brass waste as per standard pattern including cutting and painting of brackets and making good the walls Make Cera Model CONCORD( Basin - 1022 & Pedestal 1121 ) or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing & Fixing Table Top Wash Basin Size 550 x 400 x 140 mm Make Cera model Calburt (S2020137) complete with CP Waste or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Anglular stop cock, With Wall Flange, Make Jaquar range Opal Prime Model OPP-CHR-15053PM or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Bib Tap with Wall Flange, Make Jaquar range Opal Prime Model OPP-CHR-15037PM or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing Single Lever Basin Mixer Without Popup Waste with 450mm Long Braided Hoses Make Jaquar range Opal Prime Model OPP-CHR-15011BPM or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

P/F of chinaware Rimless, Blind Installation Wall Hung WC In White Matt With PP Soft Close Slim Seat Cover, Hinges And Accessories Set, Size: 375x520x400 mm make Jaquar Model SLS-WHT-6953BIPPSM or equivalent in the same range of AOR

Providing and fixing of Single Piece Slim Concealed Cistern Body with Instalation Kit & S-Type Drain Pipe Connection Set For Wall Hung WC (Without Flush Control Plate) Make Jaquar Model JCS-WHT-2400S or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Control Plate Kubix Make Jaquar Model JCP-CHR-352415 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Single Lever 3-inlet Diverter Exposed parts kit Consisting of Operating Lever, Cartridge Sleeve, Wall Flange(with Seals), Button Assembley Sleeve and Button Cap (Compatible With ALD-193) Make Jaquar Model OPP-CHR-15193NKPM or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing Concealed Body for 3-inlet Singlr Lever Diverter with Button Assembly,Cartridge Sleeve but without Exposed Parts Make Jaquar Model ALD-CHR-193N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Sink Mixer with Swiniging Spout ( Wall Mounted Model ) with connecting Legs & Wall Flanges complete Make Jaquar range Florentine Model FLR-CHR-5309N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of C.P. Towel Rail 600 mm long complete in all respects make Jaquar range Continental Model ACN-1111NM or equivalent in the same range of AOR

Providing and fixing of C.P. Towel Ring Square with round flange complete in all respects make Jaquar range Continental Model ACN-1121N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of C.P. Tumbler Holder complete in all respects make Jaquar range Continental Model ACN-1141N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of C.P. Towel Rack 600mm Long With Lower Hangers Complete in all respects Make Jaquar range Continental Model ACN-CHR-1185S or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Corner Glass Shelf ( with bracket ) make Jaquar range Continental Model ACN-1173N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Shower Arm Wall Mounted with Wall flange

SHA 479L450 / 450 mm long round or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing & fixing of Overhead Shower Square Shape Single Flow Make Jaquar Model

150 mm / OHS 1605 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Hand shower Round Shape ( ABS body Chrome Plated with Gray Face Plate ) with Rubit Cleaning System make Jaquar Model

80 mm dia / HSH 1937 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing Easy Flex Tube in Chrome Finish 1.5 mtr long with nuts complete make Jaquar Model SHA-549 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of C.P. Toilet Roll Holder complete in all respects make Jaquar range Continental Model ACN-1151N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing & Fixing CP Soap Dispenser make jaquar Continental 1135N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of C.P. Soap Dish Holder complete in all respects make Jaquar range Continental Model ACN-1131N or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing & fixing Hand Shower (Health Faucet) (ABS Body) with 8mm Dia 1.2 Meter Long Easy Flexible Tube and Wall Hook Finish Chrome complete in all respects Make Jaquar Model ALD-CHR-573 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Regular Body of concealed Stop cock Suitable for 15 mm Pipe Line with Protection cap ( Without Exposed Parts ) Make Jaquar Model ALD-CHR-083R or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Exosed Part Kit of Concealed Stop Cock with fitting sleeve Make Jaquar Model OPP-CHR-15083KPM or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and laying of UPVC pipe, IS-4985 marked, Pressure 6 kg/cm2 including cutting, joining, solvent and all necessary fittings complete in all respect except excavation.

Providing and fixing of CP sink Waste for S.S Sink of approved make

Providing and fixing of Gun metal peat valve ISI Marked

15 mm dia nominal bore

Providing and fixing HCI Cover with frame for GT & IC of approved make

Providing and fixing of C.P. brass Jet with brass nossel steel flange & PVC flexible pipe complete in all respect DSR 17.16A

Providing and fixing PTMT Ball cock of approved quality, colour and make complete DSR 18.62

20 mm nominal bore, 120 mm long, weighing not less than 198 gms DSR 18.62.2

Providing and fixing GI Elbow 32 mm x 80mm approved make

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. DSR 17.22A

Providing and fixing of CP Brass/SS Towel Ring with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36524 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS Towel Rail 600mm of with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36520 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS/ABS overhead shower with swiveling Joint , 125mm dia (min) with C.P Brass/ S.S Shower Arm and flange to the satsifaction of EIC of approved make ESSCO Model No. 536A & 542A or equialent Model of CERA /Kerovit/ Jal

Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Waste for Basin of approved make

Providing and fixing of C.P. brass Cup ( Heavy Duty ) of approved make

Providing and fixing Hydro Pnematic Pump of Size 0.5 H.P Single Pump complete with Connecting cable, NRV having discharge 13 LPM at 45 M head make crompton model Minfroce II or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing 1 H.P Monoblock Boosing Pump including cost of fixing & fitting accessories.Head Range 6 to 39 mtr, Discharge 3180-950 LPH, CG MiniSapphire. or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Manufacturing, Supplying and fixing of Rain Shelter for Pneumatic Pump / Monobloc Pump made from MS Angle covered with Fibre Sheet including grouting complete to the satisfaction of EIC

Please Enable Macros to View BoQ information