Maint and repair to joinery, plastering, roof treatment, plumbing, flooring and misc items in MH Offrs mess, Pers line, LAO, Int and Fd Hosp OTM and Md Accn under AGE B/R-II at GE Gurdaspur.

Amount

Taking down cement plaster of any description built in cement mortar of any description as specified

M&L for 15mm thick cement rendering in cm 1:6 on brick or concrete surfaces other than fair surface, finished the surfaces even and smooth without using extra cement built in cement mortar all as specified & directed.

All as per item No 02 above but 5mm thick on ceiling in CM 1:3

M&L for 15mm thick cement rendering on fair faces in cm 1:4 on brick or concrete surfaces fair finished the surfaces even and fair without using extra cement using water proofing compound complete all as specified & directed. (Note :WPC shall be measured and paid for separately).

M&L for preparation of new plastered surface and applying two coats of cement base paint all as specified and directed.

M&L for prepration of newly plastered surface of ceiling applying three coats of white wash complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper (of approved shade) on walls over primer chalk whiting, on plastered surfaces complete all as specified.

M&L for preparation of old surface of existing treatment and applying one coats of cement based paint all as specified & directed.

M&L for preparation of old plastered surface of wall by brooming down, making good holes, cracks, etc and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as directed by Eng-in-charge.

M&L for preparing old plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of walls including cornices and applying one coat of distemper oil emulsion paint, white or tinted complete all as specified and directed.

M&L for preparing old decorated plastered surface by complete removal of existing treatment and applying two coats oil bound distemper over 1mm thick wall care putty to make surface smooth complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer all as specified and directed.

All as per Srl item No 14 above but on steel surface on red oxide primer.

M&L for prepartion of old painted surface of wood & wood based surfces of any decsription not other wise described over 10cm width or girth and applying one coat of synethic enamel paint complete all as specified and directed.

All as per Srl item No 16 above but applying one coat on steel /iron surfaces.

Taking down chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed

All as per Srl item No 18 above but size of opening exceeding 1.5 Sqmtr but not exceeding 4 Sqmtr.

Taking down shutters of any description of size exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed.

Taking down shutters of any description of size exceeding 1 sqm but not exceeding 2 sqm each and refixing the same opening complete all as specified and directed

S&F in repair steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 complete incl two coat of painting: :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. (Note: Wire cloth, glass shall be measured and paid for separately).

S&F in repair steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/ TD-1019/08 Sh 1/3 to 3/3 including making good dismantled portion in PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) for hold fasts, painting with one shop coat of zinc chromate primer incl two coat of painting complete all as specified and directed. (Note: Glass/ wire cloth shall be measured and paid for separately).

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos (200mm long) in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed.

S&F powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed.

S&F anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F sheet glass 5.5mm thick , ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane all as specified and directed.

S&F in repair door closer hydraulically regulated (aluminium die cast body) designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed.

S&F pressed steel frames 1.25mm thick for door size of frame125 X 60mm with single or double rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces and complete all as specified and directed.

S&F pressed steel frames 1.25mm thick for door size of frame 105 X 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges and two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces complete all as specified and directed.

S&F 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels on both side complete all as specified and directed.

S&F 2nd class hard wood factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed.

S&F factory made single extruded WPC (wood polymer composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calciumcarbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum grame density of 750 kg/ cum, screw withdrawal strength of 2200 N (face) & 1100 No (edge), minimum compressiv e strength of 58 N/ mm² , modules of elasticity 900 N/ mm² and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge. (Note :- M.S hold fast, lugs, SS dash fasteners shall be paid for separately).

S&F facoty made solid PVC moulded door shutter of size 28mm to 30mm thick (styles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face all as specified and directed.

S&F MS framed work as in door chowkhts or gates of angle or other section with gusset plates, rail, bracesetc and similar work incl primer conforming to Fe 410-0 complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) in hold fast for doors all as specified and directed.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc 0.50 Sqm each complete all as specifid and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putty in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/bolt in metal/wooden frame to be carried out complete all as specified and directed.

S&F aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 through bolt or with screw complete all as specified and directed.

S&F aluminium alloy, anodised 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repair cutrain rod 20mm dia of mild steel with PVC coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

M&L for 18/19 mm prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed.

S & F 150 mm hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided for as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed.

M&L for rendering 15mm thick in cm 1:3 in sunken portion of slab using waterproofing compound all as specified and directed. (Note : Water proofing compound shall be measured and paid for separately).

Supply only integral water proofing compound.

M&L for APP based polymeric membrane minimum weighing 3 kg/ sqm and minimum 3mm thick, reinforced with polyster non woven fabric (weight not less than 150 gms/ Sqm) laid on primed surface with bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

M&L for PCC 1:5:10 type E2 (using 40mm graded crushed stone aggregate) as in filling, foundation and mass concrete in sunken floor complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

S&F for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exc 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:6 and dismantling of existing tile floor and screed complete all as specified.

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and dismantling of existing tile floor and screed complete all as specified.

M&L for dark coloured vitrified tiles10 mm thick joint free (square/rectangular) area of each tile n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and dismantling of existing tile complete all as specified.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet (pedestal pattern)fixing with bolts ,white colour, incl stainless steel L-type jet spray with 1 m hose pipe, connection to tap and to flushing pipe, anti-syphonage pipe, etc. incl seat cover complete including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC trap, integral foot rest including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

S&F in repair vitreous China wash hand basin, with full pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and 32mm PTMT coupling complete all as specified and directed.

S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern) white with grating, waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing arround urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe,brass CP urinal spreader complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash basin and sink all as specified and directed.

S&F in repair PVC low level flushing cistern duel type 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 73 above but fixing only including cleaning and new fittings (old serviceable pipe re-used).

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 75 above but fixing only including cleaning and new fittings (old serviceable pipe re-used).

S&F PVC (SWR) pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height including dismantling of old pipes complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height including dismantling of old pipes complete all as specified and directed.

S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.

S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.

S & F in repair 110 bore PVC(SWR) branch pieces (single T), single (equal or unequal ), ordinary or inverted) (or with parallel branches with oval access door complete all as specified and directed.

S&F in repair 75 bore PVC(SWR) branch pieces (single T), single (equal or unequal ), ordinary or inverted or with parallel branches with oval access door complete all as specified and directed.

M&L in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 75mm dia complete all as specified and directed.

S&F stack clamps (for 110 mm pipe) out of 20 x 1.5mm galvanised mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F 100mm dia stainless steel grating with or without hinge type or hole type complete all specified and directed.

S&F in repair brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 225mm long, 15 mm size complete all as specified and directed.

S&F in repair brass chromium plated tublar towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floor finishing even and smooth without using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in plinth protection finishing fair and even complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) in foundations as in sub base, filling and mass concrete to raise the level complete all as spcd and directed.

M&L coloured chequred cement concrete tiles with grey cement and no pigment, 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement mortar 1:6 including dismantling of existing tiles complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement, no pigment & joints filled with sand including dismantling of existing tiles complete all as specified and directed.

M&L for 25 mm sand filling under floors or in foundations including watering and consolidation all as specified & directed.

Dismantling of brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and directed

All as per Srl item No 97 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 96 shall be reused after necessary cleaning of mortar)

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement morter 1:4 complete all as specified and directed.

M&L for green marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 including dismantling of existing marble complete all as specified and directed.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded crushed stone aggregate) as in chajjas facia, shelves etc and similar work complete all as specified and directed.

M&L for 6mm dia and over TMT bar cut to length bent to shaps including cranking binding spirally, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips all as specified and directed.

Use and waste of form work to chullah hoods, shelves, chajjas, weather shades, corbels, water troughs and similar items including edges rough finished surfaces of concrete complete all as specified and directed.

S&F in repair kitchen sinks made of stainless steel 1 mm thick with plugs, washers, wastes and coupling including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowlsize 410mm x 330mm x 160mm including fittings arrangement complete all as specified and directed

S&F Gl powder coated frame work for seamless false ceiling, size of grid 605 x 605mm with main tee of size 32mm x 23.5mm x1.5mm thick, cross tee of size 25mmx 23.5 mmx1.28mm and angle of size 23.5mmx23.5mmx1.2mm fixed on wall all powder coated finish on exposed surface of tee and angle, hung from ceiling using 2mm dia GI suspension wires and 'J' bolts , washers, nuts spaced at 1200mm both ways including making niches for fans/light all as specified and as directed.

S&F 12mm thick perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid, including demolition of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets any thickness, including cover fillets complete all as specified and as directed.

S&F in repair 7-8 mm thick PVC hollow wall panelling consisting of wood grain printed pvc sheet inclusive of solvant cement and fixing at site on PVC frame formed by sticking high density EPS, flame retardent (TF) grade, heavy duty with taper strip weather proof, water proof, termite proof including all C and U type PVC section with matching of panelling fixing at border of panelling complete all as specified and directed by Engr-in-Charge.

S&F in repair solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification complete all as specified and directed.

S&F in repair 12mm thick fibre insulation boards, ordinary type and fixed to any frame work with nails complete all as specified and directed.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 67,245/- from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

M/S Harjinder Singh Contractor (BID ID -3341207)

M/S GAGAN CONSTRUCTION CO (BID ID -3341343)