REPAIR TO FENCING, COMOUND WALL, DRAIN AND CERTAIN MISC WORKS AND CLEANING OF SEWAGE LINE, SEPTIC TANK /SOAK WELL AT TECH AREA OF KALU CHAK AND REPAIR/REPLACEMENT OF HANGER DOOR, ROOFING

Cleaning manually of blocked WC seat trap, inside house and gully trap it includes remove/refixing of grating and cleaning of WC's trap,kitchen/bath traps any type/pattern (pedestal/squatt pattern) upto 1st manhole and making the drain pipe of any size full functional by flushing with water to entire satisfaction of Engr-in-Charge including cleaning of 1st manhole and removing the waste material/sludge etc toout side form defence land and burring the same in pits complete all as directed by Engr-in-Charge.(Measurement will be carried out each time depend on blockage)

Cleaning of underground SGSW pipes of size 150mm dia by rodding from manhole to manhole or manhole to septic tank/well including taking off manhole cover and cleaning of manholes of any size and depth and removing waste material/sludge to a distance of n. exc 50m and burrying the same pit and replacing manhole cover in position after cleaning (measurement will be carried out each time depend on blockage) complete all as specified and directed by Engr-In-Charge.

Cleaning and dewatering of septic tanks/pits of any depth incl let and outlet chamber and removing slauge (in solid and semi solid), silt, both organic and in-organic nature including any type of waste matterial after plugging of incomimg sewage line and removing waste material / sludge etc to out side form defence land and burrying the same in pit complete all as specified and directed by Engr-In-Charge.

Demolition un-reinforced cement concrete in ground floor and paving any surfaec, complete all as specified and directed.

Demolition reinforced cement concrete of any depth complete all as specified and directed. Note: Demolition of RCC works any depth any postion shall be included.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegetation upto and including roots upto 30mtrs hight form ground complete all as specified and directed. Note: This included any thick of plaster and already of tiles or mosaic tiles etc.

M & L for cement concrete (1:4:8) type D-2 (40mm graded stone aggregate) in foundations Complete all as specifed and directed by Engr-In-Charge.

M&L PCC 1:2:4 type B1 (Using 20mm graded stone aggregate )as in benching, bed plates, coping and the like including weathering, slightly rounded or chamfered angles as direceted including necessary form work and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge.

Rendering 15mm thick cement plaster in cement mortar 1:4 on fair face of brick work or concrete surface, finished even and smooth without using extra cement, with waterproffing compound admixture complete all as specified and as directed. Note:-Supply only liquid water proofing admixture shall be measured and paid seperately under relevant item of this BOQ

Precast cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in manhole cover/drain cover set in CM 1:4 complete all as specified incl form work and directed.

M&L for 25mm thick PCC type BO 1:2:4 (12.5mm graded aggregate in flooring finishing rough to recieveing Top layer for flooring complete all as specified and directed.

M&L for glazed ceremic tiles 300x250x7 mm or 450x350x7 mm thick, as in dado, vertical surfaces set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.

M&L for Joint free colored non skid ceramic tiles 7to 8 mm thick, area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 to match Shade, pattern, laying etc of tiles complete all as specified and directed.

M&L chequered or machin pressed cement concrete coloured tiles machine pressed conforming to IS 13801:1993 and ISI marked, size not less than 300mm x 300mm (Approx), thickness 25mm, as in floor, paving set and jointed in neat cement to match with gray pigment all as specified and directed.

M&L for Brick work with sub class 'B' bricks, straight or curved on plan to any redius in half brick thick wall built in cement mortar 1:4, complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C1 using 20 mm graded stone agg in Sub floor, finished even and fair w/o using extra cement.

M/L Cement concrete 1:3:6 type C2 using 40mm graded stone crushed aggregate in plinth protection, 75mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete.

M&L for reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for slabs supported on wall, beams and columns, in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ,complete all as specified and directed Note : Reinforcement shall be measured and paid for separately.

M&L for Steel reinforcement 10mm dia and over, TMT bars, cut to length, bent to shape required including, cranking, bending, spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and directed .

M&L for steel reinforcement 6 to 8mm dia and over, TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed .

M& L cement concrete 1:3:6 Type C-1 (20 mm graded Aggregate ) in surface channels and drain as all aspecified and directed by Engr in charge.

M&L 10mm thick rendering on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on internal walls in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

M&L 20 mm thick screed bed or bedding layer in CM 1:6 finished fair and even for laying floor finishes/tiles etc complete all as specified and directed by Engineer-in-Charge.

M & L roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove duct etc complete all as specified.

Removal of soil/silt, Shrubs and other waste from the RCC& Brick drains Up to Wide and dipth Approx (1.0x1.20) RM and cleaning the surface throughly for free flow complete all as directed by Engr-In-Charge. Note : All sluge and waste matrial have carry out from its locatonn out from Air Force sation.

Dismantling wrought iron or mild steel work,frame work such as truss, wind tie, angle frame work , concertina coil of any description complete all as specified and as directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, and removing surplus soil to distance n exc 50m and making good surface of any type of soil.

M&L for MS work conforing to Fe-410-0 of Fe-310-0 Grade for fencing posts and struts in fencing and gate grill and grating including cutting bending top to shape as directed drilling holes matching for barbed wire etc. including all necessary drilling work complete and all as specified

Supply only chain link MS Galvanised 3.80mm dia and 50mm pitch of wire fencing including line wires, any mesh, size and type to any type of standars, rails, straining bolts, etc. including provision of binding wire complete all as specified.

Fixing only Chan link frncing including line wires, any mesh, size and type of standerds, rails, straining bolts,etc. including provission of binding wire complete all as specifired.

Mild steel screw bolts (machine made) with h

exagonal or square heads at one ends and screwed the other ends, or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut exc 5 cm long but n-exc 10cm, dia of shank 10 mm , complete all as specified and as directed

Preparation of steel or iron surfaces of any description, over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified.

Preparation of steel or iron surfaces of any description, n exc 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified.

Supply and fixing Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of of standard rails straining bolts, including, securing or tying at crossings with and Provision of galvanised mild steel wire, stapples or steel pins, etc. as directed (each line wire to be measured) complete all as specified.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking pave rblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete all as specified and directed.

Providing and laying at or near ground level actory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Dismantling steel or asbetos cement (corrugated/ semi corrugated etc) sheet in roof covering complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Note:- work up to 10 m height.

All as per item No.6 but 0.80mm above but plain sheet fix in valley gutter / ridge complete all as specified and directed.

Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410 W(Gde E-250) quality Complete all as specified.

M&L for MS work as in roof trusses (framed) trussed, purlins ,post, rafters including distant pieces, cleats etc including cutting and welding required confirming to grade Fe 410-W grad quality 'B' complete all as specified and directed.

M&L for MS work as in wind tie or any other work incl cutting, drilling holes etc. complete all as specified and directed.

M&L for MS Plates (plain or chequered) channels, square cut, notched chamfer or square cut or notched (ordinary and counter sunk) forming holes without any attachment with MS Gde Fe 410-quality 'B' complete all as specified and directed.

M & L for prepration of new plastered surfaces and applying two coat of approved shade of oil emulsion distemper on walls all as specified and directed.

S&F formwork to Square, rectangular or polygonal sides of pillars, posts, struts, piers, columns and stanchions fair finished surfaces complete all as specified

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete including removal all debries exceeding 50m but not exceeding 100m all as specified and directed by Engineer-in-Charge.

M&L Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specifiedand directed by Engg-in Charge.

Complete removal of wall and ceiling exisiting treatment and applying 1mm coat of plater of paris(putty) one cote of Acrylic Smooth exterior paint @ .835 ltr/10 sq of required shade over one coat of primer m complete all as specifiedand directed by Engg-in Charge.

M&L for preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint Complete all as specified and as directed.

M&L 75 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone agg in floor, complete all as specified.

Providing precast cement concrete or simlar work of PCC 1:2:4 Type B-1 20mm graded aggregate (of any section indicated), with plain fair faces, including chamfers, weathering's, throat- ing etc. and set & jointed in CM 1:4 complete all as specified.

Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified.

Dismantling of roller, purlin, angle, pully, channel, angle, hanger gates including taking down shutter Approx up to Size of 5x9.00RM and fixed in same position (Adopting all safety measures and scaffolding) after rectification /repair/replacement of connected items Supply and fixing in repair for hanger gate of top rollers , channels, angle, cleats, sliding bolts, pully and connected tems, which ever fixing and repair to doors with rollers of hanger gates,existing material removal and refixed in the same position with PPGI plain sheets, all works to be executed upto 12m height. Rollers support and middle point breaker of roller where side in stopped roller, which are weleded with angle and same fixed with nuts & bolts for safety purpose of wheel. Contractor to arrange to all necessary arrangement of scaffolding and safety measures etc.

S&F in repair Steel rolling shutters, 1.25mm thick with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed by Engineer-in-Charge.

S/F in repair Safety lever locks mild steel with 4 levers for rolling shutt

erscomplete all as specified and directed.

S&F in repair Ball bearing for rolling shutters after removing all accessories which are required to be removing all accessories which are required to be removed and replacing the unserviceable ball bearings will refixed the accessories at the same place as specified and directed by Engr-in-Charge.

S&F Wire netting of stainless steel wire 1.4mm dia 25mm pitch fixed with tinned tacks of stainless steel wire staples complete all as specified and directed.

S&F for in Repair rain water pipe 200mm dia with single socket joints fixed to wall including bend or Tee which wiil be required with stack clamp fixed in repair (work commence hight upto 12 mtr) complete all as specified and directed by Engineer-in-Charge Note : All clamp reviting,or wildingin brick wall or weilding to steel surface without any extra cast.The contractor will be provide with all safty measures

SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.