CA NO GE/H-08/2021-22 REPAIR/MAINT OF VARIOUS PUMP MOTOR SETS LT ELECTRIC CONTROL PANELS INSTALLED WITH PUMP HOUSES INCLUDING ALLIED WORK NEEDS FOR UPKEEP MAINT OF WATER SUPPLY AND FIRE FIGHTING SYSTEM AT AHRR UNDER GE E/M R AND R HOSP DELHI CANTT-10

Amount

Dismantling centrifugal pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking and replacing the unserviceable spares such as replacement of shaft, impller, shaft sleves etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 30 HP complete all as specified and directed by Engr-in-Charge. Note : (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, bush collar, gland packing, CI gland, key coupling and any kind of welding/lath for refixing/connecting to pipe line etc. are deemed to be included in the cost of servicing. (ii)Bearing and bearing housing block if required to be replaced will be measured & paid separtely under relevent items. (iii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs. 1000/- per day will be charged.

Supply only ball bearing as per site requirement of 30 HP pump motor complete all as specified & directed by Engr-in-Charge.

Supply only SS shaft sleeves in 30 HP pump with complete nut, bolt & stufs, nut & flanged, upper & lower, studs & nuts complete all as specified & directed by Engr-in-Charge.

Supply only bearing housing for 30 HP pump complete all as specified & directed by Engr-in-Charge.

Supply only bearing cover DE suitable for 30 HP pump complete all as specified & directed by Engr-in-Charge.

Dismantling centrifugal pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking and replacing the unserviceable spares such as replacement of shaft, impller, shaft sleves etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 25 HP complete all as specified and directed by Engr-in-Charge. Note : (I) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, bush collar, gland packing, CI gland, key coupling and any kind of welding/lath for refixing/connecting to pipe line etc. are deemed to be included in the cost of servicing. (ii)Bearing and bearing housing block if required to be replaced will be measured &paid separtely under relevent items. (iii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs. 1000/- per day will be charged.

Supply only ball bearing as per site requirement of 25 HP pump motor complete all as specified & directed by Engr-in-Charge.

Supply only Shaft SS 410 for 25 HP complete all as specified & directed by Engr-in-Charge.

Supply only Drive end Bearing housing CI complete all as specified & directed by Engr-in-Charge.

Supply only Air release valve of size 20 mm for 25 HP complete all as specified & directed by Engr-in-Charge.

Dismantling centrifugal pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking and replacing the unserviceable spares such as replacement of shaft, impller, shaft sleves etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 100 HP complete all as specified & directed by Engr-in-Charge. Note : (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, bush collar, gland packing, CI gland, key coupling, ball bearing and any kind of welding/lath for refixing/connecting to pipe line etc. are deemed to be included in the cost of servicing. (ii) bearing housing block if required to be replaced will be measured &paid separtely under relevent items. (iii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

Supply only CI centre ring for 100 HP complete all as specified & directed by Engr-in-Charge.

Supply only Cast iron bearing housing box complete all as specified & directed by Engr-in-Charge.

Supply only CI Impeller with key, stud, MS bolts & nuts for 100 HP as per size requirement (1/2x2",5/8x2.5") MS stud 19x65mm) complete all as specified & directed by Engr-in-Charge.

Supply only tyre coupling for 100 HP code no TC /M - 17 complete all as specified & directed by Engr-in-Charge.

Supply only gun metal sleeves for 100 HP Pump set complete all as specified & directed by Engr-in-Charge.

Supply only cooling fan for 100HP induction motor complete all as specified & directed by Engr-in-Charge.

Dismantling centrifugal monoblock pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking replace the unserviceable spares such as replacement of shaft, impller, shaft sleves, ball bearing etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 15 HP of any make complete all as specified & directed by Engr-in-Charge. Note : (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, gland, SS key coupling, connection piece, water deflector, ball bearing, any kind of welding/lath for refixing/connecting to pipe line etc. are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

Supply only rotor guard for 15 HP complete all as specified & directed by Engr-in-Charge.

Supply only SS rotar sleeves for 15 HP complete all as specified & directed by Engr-in-Charge.

Dismantling centrifugal monoblock pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking and replacing the unserviceable spares such as replacement of shaft, impller, shaft sleves etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 10 HP of any make complete all as specified & directed by Engr-in-Charge. Note : (I) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, SS key coupling, connection piece, water deflector, ball bearing, any kind of welding/lath for refixing/connecting to pipe line etc. are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

Supply only CI upper & lower housing for 10 HP complete all as specified & directed by Engr-in-Charge.

Supply only CI motor base for 10 HP complete all as specified & directed by Engr-in-Charge.

Supply only revolving disc for capacity10 HP complete all as specified & directed by Engr-in-Charge.

Supply only rotor guard for 10 HP complete all as specified & directed by Engr-in-Charge.

Supply only SS rotor sleeves for 10 HP complete all as specified & directed by Engr-in-Charge.

Dismantling centrifugal monoblock pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking and replacing the unserviceable spares such as replacement of shaft, impller, shaft sleves etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 7.5 HP of any make complete all as specified & directed by Engr-in-Charge. Note : (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, ss coupling, connection piece, water deflector, Ball bearing etc. any kind of welding/lath for refixing/connecting to pipe line are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs. 1000/- per day will be charged.

Supply and fix in repair only ss coupling for 7.5 hp monoblock pump set complete all as specified & directed by Engr-in-Charge. (This item is independent of item No. 27 here-in-above).

Supply and fix in repair only connection pieces suitable for 7.5 HP pump complete all as specified & directed by Engr-in-Charge. (This item is independent of item No. 27 here-in-above).

Supply only rotor guard for 7.5 HP complete all as specified & directed by Engr-in-Charge.

Supply only SS rotar sleeves for 7.5 HP complete all as specified & directed by Engr-in-Charge.

Supply only sealing ring dor 7.5 HP complete all as specified & directed by Engr-in-Charge.

Dismantling centrifugal monoblock pump set and motor electrically and transportation to workshop for carrying out the preventive maintenance and repairs by checking and replacing the unserviceable spares such as replacement of shaft, impller, shaft sleves etc of any make complete with paper & sleeve, wooden stick, 'O' ring set reallignment of pump set foundation incl replacement of foundation bolts and nuts, servicing, cleaning and overhauliing, lubricating, assembling, connecting and testing complete for the capaciy of 5 HP of any make complete all as specified & directed by Engr-in-Charge. Note : (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, shaft sleeve, ss coupling, connection piece, water deflector, ball bearing, any kind of welding for refixing/connecting to pipe line etc. are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

Supply only CI upper & lower for 5 HP complete all as specified & directed by Engr-in-Charge.

Supply only impeller gun metal for 5 HP complete all as specified & directed by Engr-in-Charge.

Supply only SS rotar sleeves for 5 HP complete all as specified & directed by Engr-in-Charge.

Taking up unsv submersible pump along with motor of capacity 7.5 HP of any make/type from borewell by lowering the chain pulling and column pipe after disconnecting all electrical connections and transporting to local workshop for repair , over hauling, cleaning of impellers, rewinding of motor of any make complete with equivalent gauge of copper winding wire & insulating materials, any kind of welding/lath work and Refixing the same after testing & commosioning of motor complete all as specified and directed by Engr-in- Charge. Note : spares such as gasket, grease, bolt, nuts, studs, flanged and washers, ss sleeve, coupling, gun metal bush, rotor sleeve, water seal, inlets, stage impeller etc. are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

Taking up unsv submersible pump along with motor of capacity 5 HP of any make/type from borewell by lowering the chain pulling and column pipe after disconnecting all electrical connections and transporting to local workshop for repair , over hauling, cleaning of impellers, rewinding of motor of any make complete with equivalent gauge of copper winding wire & insulating materials, any kind of welding/lath work and transportaion to work for repair & refixing the same after testing & commissioning of motor complete all as specified and directed by Engr-in-Charge. Note (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, ss sleeve, coupling, gun metal bush, rotor sleeve, water seal, inlets, stage impeller etc. are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

Taking up unsv submersible pump along with motor of capacity upto 03 HP of any make/tytpe from borewell by lowering the chain pulling and column pipe after disconnecting all electrical connections and transporting to local workshop for repair , over hauling, cleaning of impellers, rewinding of motor of any make complete with equivalent gauge of copper winding wire & insulating materials, any kind of welding/lath work and transportaion to work for repair & refixing the same after testing & commissioning of motor complete all as specified and directed by Engr-in-Charge. Note : (i) spares such as gasket, grease, bolt, nuts, studs, flanged and washers, ss sleeve, coupling, gun metal bush, rotor sleeve, water seal, inlets, stage impeller etc. are deemed to be included in the cost of servicing. (ii) Pump/Motors should be returned and fixed after repair within 4 days of intimation of unserviceability, if the same is not reinstalled within the stipulated period then a penalty of Rs.1000/- per day will be charged.

M&L dismantling all connection electrically including transportation to workshop and fixing the same after removing the unservceable winding from the motor cleaning the starter slots, rewinding with appropriate size and or existing super enamelled copper winding wire and insulating to the existing class of insulation, cleaning the starter assmebly including fixing of terminal, copper lugs etc., tetsing and assmebling of 3 phase motor of 30 HP capacity complete all as specified & directed by Engr-in-Charge.

All as per item No. 40 herein-before but for 25 HP

All as per item No. 40 herein-before but for 100 HP.

All as per item No. 40 herein-before but for 15 HP.

All as per item No. 40 herein-before but for 10 HP.

All as per item No. 40 herein-before but for 7.5 HP.

All as per item No. 40 herein-before but for 5 HP . Note : For Srl item No 1, 6, 11, 18, 21, 27, 33, 37 to 46 , if pump motor is required on urgency (the same will be intimated by JE/Engr-in-charge) then Contractor should provide and installed a temp pump motor on their own arrangement with in the 4 hours of dismantling otherwise a penalty of Rs.1000/- per day wiil be recovered.

Supply & fix end type cable joint of any size as per site requirement or as specified and directed by Engr-in-Charge.

S&F in replacement indicating light with bulb set of three(RYB) complete all as specified & directed by Engr-in-Charge.

S&F in replacement of MU-Automatic DOL starter 7.5 HP 3 Phase 415 V (MU-1ADOL with Sz5SPPR) CAT No. CS90898DOAO in L&T relay range 9 to 14A Relay range 20 to 32 Amp complete all as specified & directed by Engr-in-Charge.

S&F in replacement MK1 SASD semi Automatic Star Delta starter 5 HP 3 phase 415 Vols, AT No. SS96255 in L&T relay 4 to 6.5 Amps in sheet metal enclosure outdoor type Ip 54 with suitable angle iron grouted with PCC 1:2:4 with 20mm stone aggregate 30 cm below ground and 60cm above ground complete all as specified & directed by Engr-in-Charge.

S&F in replacement of automatic Submersible pump controller in sheet metal enclosure type three Phase 5HP 415V IP 54 with suitable angle iron grouted with PCC 1:2:4 with 20mm stone aggregate 30 cm below ground and 60cm above ground. make complete all as specified & directed by Engr-in-Charge.

S&F in replacement of automatic Submersible pump controller in sheet metal enclosure type single Phase upto 2HP 240V IP 54 with suitable angle iron grouted with PCC 1:2:4 with 20mm stone aggregate 30 cm below ground and 60cm above ground complete all as specified & directed by Engr-in-Charge.

Supply and fix in replacement Volt-ammeter 500V, 0-125A CAT Part No. CS90057OOOO inclding complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement on Load Changover Switches 4 Pole, conformes to IEC 947-3, EN-06947-3 AC-23A, 160 amps , C01604POAV complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement on Load Changover Switches 4 Pole, conformes to IEC 947-3, EN-06947-3 AC-23A, 250 amps , C02504POAV complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement Load Break swithes 4 pole, 160 amps, conformes to IEC 947-3 AC-23A, Front operated 3 pole 415V, 5m HZ complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement Load Break swithes 4 pole, 250 amps, conformes to IEC 947-3 AC-23A, Front operated 3 pole 415V, 5m HZ complete all as specified & directed by Engr-in-Charge.

S&F in replacement of Electronic motor protection relay MPR200nX , inbuilt CT's (1 A to 88 A) as per IEC 947-4-1 O/L Range (A) 32-88 complete all as specified & directed by Engr-in-Charge.

S&F in replacement of Electronic motor protection relay with in-built Earth fault protection MPR300, inbuilt CT's (1 A to 88 A) as per IEC 947-4-1 O/L Range (A) 28 to 42 complete all as specified & directed by Engr-in-Charge.

S&F in replacement of Supply monitoring devices type SM 501 (3Ph,3W), time deley On delay 5 sec and off delay 5 sec complete all as specified & directed by Engr-in-Charge.

S&F in replacement AC megnatic contractor type CM-40 or MU2 in L&T as per IS 2959/1985 complete all as specified & directed by Engr-in-Charge.

S&F in replacement single phasing preventer & dry run protection relay current type with Vi meter (Current based) CAT Part No. 90863D000 in L&T as per site requirement complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement of MCCB 100 amps 4 pole 50 KA 415 volts 50 HZ in LT control panel complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement MCCB 4 pole 415 volt AC of capacity 63 amps 25 KA cap complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacementt MCCB TP 415 volts 3 pole AC of capacity 63 amps 25KA complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement of MCCB 200 amps 3 pole 36 KA 415 volts 50 HZ in LT control panel complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement of MCCB 160 amps 3 pole 36 KA 415 volts 50 HZ in LT control panel complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement of MCCB125 amps 3 pole 36 KA 415 volts 50 HZ in LT control panel complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement of MCCB 250A 3 pole 50 KA 415 volts 50 HZ in LT control panel complete all as specified & directed by Engr-in-Charge.

Supply & fix in replacement of MCCB160amps 3 pole 25 KA 415 volts 50 HZ in LT control panel complete all as specified & directed by Engr-in-Charge.

S&F in replacemet PVC flat sheathed submersible cable copper conductor of size 4.0 sqmm 3 core,1100 volt grade complete all as specified & directed by Engr-in-Charge.

S&F in replacement PVC flat sheathed copper cable conductor of size 10 sqmm 3 core,1100 volt grade complete all as specified & directed by Engr-in-Charge.

M&L for by doing patch work in cement mortor 1:4 for inside and out side plastering ,taking out old rusted chamber cover and replacement of new ms plate 3 mm thickness with angle,hinges arrangement for suitable valve chamber 4"/6"/8" size including painting for repairs of valve chamber complete all as specified & directed by Engr-in-Charge.

Material and labour for scrubbing out the rust deposited on the surface of centrifugal pump set including its base frame and preparing surface for applying paint and applying one coat of redoxide primer and two coat of synthetic enamel paint and marking SM /MES Number for capacity of pump set 15 to 30 HP complete all as specified & directed by Engr-in-Charge.

M&L for applying one coat of synthetic enameled spray paint of existing colour on steel/iron surfaces of pipes, LT panel boards etc with and incl preparing of surface by scratching / removing rust, dust and old paints etc with wire brush, emery paper, grinder etc and making surfaces smooth for achieving better grip between surface and primer, complete all as specified & directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) as in any position n.exc. 15 cm below or above ground level and removing rubbish off premises min 500m away from bldg complex, complete all as specified & directed by Engr-in-Charge.

Material and Labour for Cement concrete in surface channels and drains type B2 1:2:4 ( 20 mm Graded Aggreagate) complete all as specified & directed by Engr-in-Charge.

Dismantling of Blocked nozzles fixed on various fountain and refixing after cleaning / servicing and setting by trial and error complete all as specified & directed by Engr-in-Charge.

S&F in replacement fountain nozzle (adjustable) of size 12mm brass complete all as specified & directed by Engr-in-Charge.

S&F in replacement of fountain nozzle (adjustable) of size 15mm brass complete all as specified & directed by Engr-in-Charge.

S&F in replacement of cover for delivery/suction pipe well cap suitable for any size bore dia consisting of two parts complete with welding and machinary work having provision of cut out for passing of column/delivery pipe and fabricated from MS sheet 3.15 mm thick duly painted with synthetic enameled paint complete all as specified & directed by Engr-in-Charge.

Supply only Calcium based granular disinfectant for water treatment more stable than chlorine gas, and stronger than Bleaching powder and sodium Hypochlorite pack of 45 Kg, Plastic drum minimum concentration of 65% complete all as specified & directed by Engr-in-Charge.

Supply and fixing gland packing upto 12mm dia complete all as specified & directed by Engr-in-Charge.

Supply and fixing water proof insulation tape for cable and wire 220V, double layer made of rubber and mastic to seal moisture and wire connection of 35mm width complete all as specified & directed by Engr-in-Charge.

S & F in repair smooth finish highly durable ruggedness copper thimbles of any type 1100 volts suitable for size up to and including 50 Sqmm cable complete all as specified and directed by EIC complete all as specified & directed by Engr-in-Charge.

S & F in repair smooth finish highly durable ruggedness copper thimbles 1100 volts suitable for size exceeding 50 and upto 95 Sqmm cable complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Soft Starter for 100 HP Pump with in built contactor, Motor protection for 75 KW 140 Amps at 40 degree C CSXI075V4C01 of L&T or equivalent make as given in tender documents with timed voltage ramp, soft stop, protection of supply, Shorted scr LED indication, Relay outputs, complete wiring etc complete all as specified & directed by Engr-in-Charge.

Supply and fixing in replacement of Soft Starter for 25 HP Pump with in built contactor, Motor protection for 18.75 KW 42 Amps at 40 degree C CSXI018V4C01 of L&T or equivalent make as given in tender documents with timed voltage ramp, soft stop, protection of supply, Shorted scr LED indication, Relay outputs, complete wiring etc complete all as specified & directed by Engr-in-Charge.

M&L Earthing in repair complete with galvanised steel earth plate electrode 600x600x6mm buried directly in ground not less than 2.25 Mtr deep below normal ground level with top edge of earth plate not less than 1.5mtr below normal ground level connected to the Galvanised iron strip 32x6mm size by means of bolts ,nuts, check nuts and washers of galvanised iron and 32x6mm GI strip Procter by provision of GI light grade pipe 40 mm bore incl provision of concrete pit in PCC1:2:4 type B-i , using 20 mm graded stone aggregates with 40 mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg /Sqm and 6mm dia bar handle ,excavation and earth work in any type of soil ,charcoal dust and salt light grade GI watering pipe 20 mm bore with funnel and wire mashand medium grade GI protection pipe 15mm bore 5 Mtr long and GI strip up to main earthing complete all as shown in electrical plate No 3 of MES Sch 2009 Part-I all as specified and directed by Engr-in-Charge. (i) Main earthing strip from earth plate electrode to test point up to length of 7.5 meters length shall deem to be included in the unit rate quoted against this item . (ii) GI protection pipe & earthing lead beyond 7.5 meter shall be measured and paid for separately under appropriate item. (iii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department .

Supply & fix in repair GI strip 32x6mm, buried in ground or fixed to wall etc for loop earthing complete all as specified & directed by Engr-in-Charge.

M&L for development of bore well of 780 mm bore and up to 50 meters deep at the pressure not less than 6kgs/SqCm by using suitable air compressor and connected items to improve the yield of bore well complete all as specified and directed by Engr-in-Charge. Note: (i) Transportation of air compressor along with tools and accessories at different location for devolopment of bore well shall be the responsibility of contractor and the rate quoted will be deemed in the quoted rate. M&L for removing the blockage in bore well casing pipe at the depth not less then 50 meters from ground level by means of bocky or any means without damaging the casing (filter and blind pipe) upto the depth of bore.

Periodical mainteneance of DG Set Engine, complete oil servicing, incl cleaining of diesel tank and radiator as recommended by manufacturer and necessary replacement of below mentioned spares and servicing work for DG Set of capacity upto 105 KVA for servicing complete all as specified and directed by Engr-in-Charge .(a) Diesel Filter (Pre+micro) (b) Engine Oil filter (c) filling Engine Oil UTL (d) filling Radiator Coolant (e) Battery terminal with sockets - 4 Sets

Supply only distilled water in sealed packing suitable for DC 12 volt battery complete all as specified & directed by Engr-in-Charge.

S&F in replacement, battery 12 V 180 AH. CAT PART No FCPO-CP 180R (MF) of Exide or equivalent make as given in tender documents complete all as specified & directed by Engr-in-Charge.

M&L for opening / taking out of FIP of diesel engine set of capacity upto 105 KVA, carrying complete overhauling/servicing/reconditioning of pump with and including replacement of all UNSV parts as required, including testing complete and re-assembling the same, fitted with diesel engine set properly in original location checking and making proper all connections, testing for smooth operating complete all as specified and directed by Engr-in-Charge. Note : (i) The cost of replaced spares / parts is deemed to be included in quoed rates and no extra cost shall be paid to the contractor in this effect. (ii) The cost of transportation (to and fro) for all kind of necessary equipment / T&P shall be arranged by the contractor to complete job. (iii) The complete works is to be carried through the authorised service centre of manufacturer only.

S&F in replacement rediator/fuel tank cap, suitable for diesel engine set of any type / make and any capacity complete all as specified & directed by Engr-in-Charge.

S&F in replacement to DG Set control panel any type incl replacement defective sensors like AMF module , relay card / board ,current transformer ,key switch , indicators , warning ,push button and checking wiring complete including made functional all the system/controls complete all as specified & directed by Engr-in-Charge.

M&L for repair to diesel engine generating set Make Kirloskar, capacity upto 105 KVA and dismantling of the engine carefully, checking throughly all the parts including repair/replacement of the all defective parts through authorised service engineer/mechanic from auth dealer. Reassembling the engine after overhauling including commissioning testing complete all as specified and directed by Engr-in-Charge. (a) Repair to cylinder head including fixing and testing complete. (b) Valve, valve seats and valve guide, cutting, grinding and polishing complete. (c) Reaming, grinding and fixing of small end bushing of connecting rod. Note : 1. The cost of replaced spares / parts is deemed to be included in quoed rates and no extra cost shall be paid to the contractor in this effect. 2. The cost of transportation (to and fro) for all kind of necessary equipment / T&P shall be arranged by the contractor to complete job. 3. The complete works is to be carried through the authorised service centre of manufacturer only.

M&L fixing in replacement of Digital Display Percentage water level sensor for overhead tank/sump with 5 stage indicator and 6 sensors & feature of Alarm on low & high levels.the system to have alarm by-pass & different alarm annunciate to differentiate high & low levels including all necessary fittings complete all as specified & directed by Engr-in-Charge.

S&F in replacement sensing copper cable multi strand wire of 12 core for connection to sensors including all necessary electrical & mechanical fittings complete all as specified & directed by Engr-in-Charge.

M&L disconnecting electrically, dismantling from foundation and removing from site LT panel and depositing the above to MES store of any size or type all as required at site and as specified and directed by Engr-in-Charge.

PRASAD ELECTRICALS

amtoindia

GLIBS CONSTRUCTION