REPAIR/REPLACEMENT OF LT UG CABLE, STREET LIGHTS, MCCB CAPACITOR PANELS, DG SET CONTROL PANEL, EARTHINGS AND SOME OTHER MISCELLANEOUS WORKS AT DGQA UNDER GE (UTILITY) SECUNDERABAD

Amount

Supply, Install Testing & Commissioning of wall mounted Indoor type totally enclosed LT panel Board CPRI APPROVED , IP 55 compartmentalised design, dust and varmin proof of suitable size suitable for 440 Volt 3 phase 4 wire system made out of 2.0mm thick CRCA sheet and built upon regid frame work having front hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be Epoxy Powdwer Coated and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom and TOP. The Panel shall be emmbeded with 40 x 4 mm MS Angle Iron frame a complete all as specified and directed by Engr in charge:- (a) Aluminium bas bar 200amps - 04 Nos, supported with suitable size of heavy duty porcelain stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 100 amps ,415 volt ,16 KA Breaking capacity 4 pole Electromagnetic release duly connected to Bus Bar As IN COMING - 02 Nos. Make : Legrand model No: 420015 or equivalent from Schinder/L&T/Hagar/C&S as approved by GE. (c) ON Load changeover switch cubical type open execution 200 amps TPN 415 volt duly connected to Bus bar -01 No. Make : HPL sucomec/L&T /HAVELLS EURO LOAD (d) MCB TP, 32 Amp, 3 Pole, 415 Volt, 10 KA Breaking Capacity duly connected to Bus-bar as OUTGOING - 02 Nos. Make : Legrand /Havells/Hagar

Supply and lay in trenches/fixed to walls/poles etc and commissioning XLPE insulated and PVC sheathed heavy duty LT 1100 Volts grade armoured under ground cable with aluminium conductor of 2 Core 10 Sqmm incl taking out of existing cable all as directed. Make : Havells/Finolex or equivalent as approved by GE. Note :- Earth work excavation, sand cushioning and brick protection shall be measured and paid separately.

All as per item No 03 here in before but 4 Core 16 Sqmm

All as per item No 03 here in before but 3.5 Core 25 Sqmm

All as per item No 03 here in before but 3.5 Core 35 Sqmm

All as per item No 03 here in before but 3.5 Core 50 Sqmm

All as per item No 03 here in before but 3.5 Core 70 Sqmm

All as per item No 03 here in before but 3.5 Core 95 Sqmm

All as per item No 03 here in before but 3.5 Core 120 Sqmm

All as per item No 03 here in before but 3.5 Core 150 Sqmm

All as per item No 03 here in before but 3.5 Core 185 Sqmm

All as per item No 03 here in before but 3.5 Core 240 Sqmm

M&L for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 4 core laid in trench /poles/on wall all as specified and as directed Make : Havells/KEI/Plaza

Taking out and Relaying of LT cable of size10sq mm to 25 Sqmm 2/3.5 core after carrying out necessary Repair such as joining with Epoxy joint and laid with sand Cushioning and brick protection and making connection By using Lugs all as specified and directed by ingr in charge. Note: (a) Earth work , sand Cushioning, brick protection, LT Joints shall be measured and paid separately under relevent Item. (b) Retrived serviceable bricks/ PCC cover shall be reused under relevent item.

Supply and lay GI tubing, 100 mm bore light grade for cable protection at road crossing / on poles and tubing sealed at both ends after laying the cables complete all as directed by Engineer-in-Charge.

All as per item No 16 here in before but 80 mm bore

All as per item No 16 here in before but 50 mm bore

All as per item No 16 here in before but 40 mm bore

S&F of cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 35 sqmm to 150 sqmm complete including taking out old unserviceable one all as specified and directed.

S&F of cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 185 sqmm to 300 sqmm complete including taking out old unserviceable one all as specified and directed.

Cutting & trimming of tree branches any girth and size touching to overhead lines and cleaning the distance 1.5 mtr both sides of overhead line with in a gap of span 35 mtrs each depositing the same for cleaning the site all as directed by the Engr-in-Charge.

Excavation in trenches not exc 1.5 mtr wide and n.exc 1.5 mtr in deep and getting out in Hard/Dense soil laying of cables etc.

Returning filling in including spreading, leveling watering and well ramming in layers n.exc 25cm thick using excavated soil

Removing excavated surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5mtr above from the starting point

Supply and laying reinforced precast concrete cable cover class LV , Type 1 flat with size 250mm x150 mm x 40mm all asspecified and directed by Engr-in-Charge.

M&L for brick protection cover of old size bricks common burnt clay building bricks sub class ’B’ laid dry and flat abutting each other with width equal to length of brick and gap between adjacent bricks not exceeding 10 mm complete all as specified.

Supply and spread approved dry river sand for foundations/Cable duct including watering and consolidation, cushioning of cable laid in trenches complete all as directed by Engineer-in-Charge. Note:- Punned thickness will be measured for payment purpose

S&F PVC separators for suitable for LT over head line of 4 conductors and all as specified and directed by Engr-in-Charge.

S&F PVC separators for suitable for LT over head line of 5 conductors and all as specified and directed by Engr-in-Charge.

Disconnection and removing of MCCB's 415 volts 4 pole 35 KA breaking capacity Adjustable type of 400 Amps Capacity burnt out one from the existing position supply and fixing the same making conncetions including install and testing complete all as specified and directed. Make : L&T/Legrand/Havells.

All as per item No 31 here in before but MCCB's 415 volts 4 pole 35 KA breaking capacity Adjustable type of 315-350 Amps Capacity

All as per item No 31 here in before but MCCB's 415 volts 4 pole 35 KA breaking capacity fixed type of 250 Amps Capacity

All as per item No 31 here in before but MCCB's 415 volts 4 pole 25 KA breaking capacity fixed type of 200 Amps Capacity

All as per item No 31 here in before but MCCB's 415 volts 4 pole 25 KA breaking capacity fixed type of 160 Amps Capacity

All as per item No 31 here in before but MCCB's 415 volts 3pole 25 KA breaking capacity fixed type of 160 Amps Capacity

All as per item No 31 here in before but MCCB's 415 volts 4pole 25 KA breaking capacity fixed type of 100 Amps Capacity

All as per item No 31 here in before but MCCB's 415 volts 3pole 25 KA breaking capacity fixed type of 100 Amps Capacity

M&L for cleaning thoroughly the street light poles/LT distribution poles of any height and any description (Maximum 11 Mtr long ) with necessary cleaning agent including scrapping of old corroded paint dirt/ rust carefully and applying two coat of synthetic aluminium paint over existing coat of paint including marking of pole numbers and colour washing of pole coping complete all as specified and directed by Engineer-in-Charge. Make:- ASIAN (APCOLITE)/ SHALIMAR (SUPERLAC)/ BERGER (LUXOL.

All as per item No 39 here in before but for Two pole structure

All as per item No 39 here in before but for Four pole structure

Labour for Tree/Grass cutting, Cleaning and levelling of the surroundings of the power house area including removal of wastage material to a distance not EXC 50 M complete all a directed

S&F galvasised steel strip 32X6 mm with saddles and fixing screws on poreceling insulator/ spacer fixed at every 1 mtr length as lightening conductor on roof/wall of explosive building and joining the same with existing earth test point all as directed by Engr-in-Charge.

Advance Maintenance Free G.I. SAFE EARTHING Electrode with PIPE of not less than 50 mm outer dia( THICKNESS NOT LESS THAN -2.5MM) and two meter length, The electrode should be of galvinised (80 -100 micron) along with earth lead as Galvanised steel strip of size 32 X6 mm 7.5 m . The GI Electrode shall be pre-filled with Cristaline Conductive Material (CCM) . The GI electrode shall be surrounded with 25 kg BackFill compound to provide maximum contact between the electrode and Back Fill Compound. Backfill compound should be eco-frendly and having RoHs certification . GI Electrode Shall be tested from CPRI.The earting pit should be cover with pcc(1:2:4 , B1) cover ,of 450 x 450 mm complete all as specified and directed. Make : ASHLOK / INDELEC/JMV /TERCEL.

S&F MCCB box made of sheet of 2mm thick size 30X20X15 CM Powder coated Suitable for fixing at Pole including two set of clamps comprisinf with the following :- (i) MCCB 63 Amps 16 KA TP with both side spreader link.

Supply and Replace Change over switch 200 amps side handel ONLOAD type 4 pole 415 volt without enclosure . Make: Havells/L&T/Schneider

Supply and Replace Change over switch 400 amps side handle /Cubical panel mounting ONLOAD type 4 pole 415 volt without enclosure. Make: Havells/L&T/Schneider

M&L preparing Steel and Iron Surfaces of any description, over 100mm width or girth and applying One Coats of Synthetic Enamel Paint (First quality) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

Supply and Replace Spreader link suitable for MCCB up to 125 Amps after taking proper shutdown in existing panel /feeder pillar box complete all as directed

Supply and Replace Spreader link suitable for MCCB of 160 A after taking proper shutdown in existing panel /feeder pillar box complete all as directed

Supply and Replace Spreader link suitable for MCCB of 200/250 A after taking proper shutdown in existing panel /feeder pillar box complete all as directed

M&L for stright Through Joint heat shriankable type suitable for 1100 volt 185 to 300 Sqmm 3.5 core complete all as specified and directed

M&L for stright Through Joint heat shriankable type suitable for 1100 volt 70 to 150 Sqmm 3.5 core complete all as specified and directed

M&L for stright Through Joint heat shriankable type suitable for 1100 volt 25 - 50 Sqmm 3.5 core complete all as specified and directed

Supply, Install Testing & Commissioning of wall mounted Indoor type totally enclosed LT panel Board CPRI APPROVED , IP 55 compartmentalised design, dust and varmin proof of suitable size suitable for 440 Volt 3 phase 4 wire system made out of 2.0mm thick CRCA sheet and built upon regid frame work having front hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be Epoxy Powdwer Coated and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom and TOP. The Panel shall be emmbeded with 40 x 4 mm MS Angle Iron frame a complete all as specified and directed by Engr in charge (Size not less than 00.9mx0.9mx0.3m) and comprising of the following :–

Supply, Install Testing & Commissioning of wall mounted Indoor type totally enclosed LT panel Board CPRI APPROVED , IP 55 compartmentalised design, dust and varmin proof of suitable size suitable for 440 Volt 3 phase 4 wire system made out of 2.0mm thick CRCA sheet and built upon regid frame work having front hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be Epoxy Powdwer Coated and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom and TOP. The Panel shall be emmbeded with 40 x 4 mm MS Angle Iron frame a complete all as specified and directed by Engr in charge (Size not less than 00.9mx0.9mx0.3m) and comprising of the following :–

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.15 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :–

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type,LT FEEDER PILLAR BOX made out of 3.15 mm thick CRCA Sheet of size 1MX.75mX.35M with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Testing after Installation complete all as specified and comprising of the following :– (a) Aluminium bas bar 200amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 100 amps, 415 volt, 16 KA Breaking capacity 4 pole Electromagnetic release duly connected to Bus Bar as INCOMING - 01 No. Make : Legrand model No: 420015 or equivalent from Schinder/L&T/Hagar/C&S as approved by GE.

Cutting the existing road straight by manual, depth and width not less than 1 mtr below ground level for passing of underground cable and filling back with excavated soil upto 75% road portion and 25% shall be made with cement concrete 1:2:4 (using 20 mm graded aggregate stone complete all as specified and directed.

M&L for road crossing/drain crossing by adopting trench less tunneling work through specified pipe jacking method by erecting the equipment to true to the allignment and gradient by haidrolic pipe jacking technique complete including tunneling, excavation in any type of soils including hard rock, HDPE pipe upto 75 mm dia of max length 15 m including jointing materials to carry LT UG cables of size upto 240 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed including refilling and making good of disturbed surface . Note : Quoted rate deemed to be exclusive of HDPE pipebut including of necessary machinaries required for the above work

Cement Concrete 1:2:4 Type B2 (20mm Graded Stone Aggregate) as Lean Concrete in Foundation of Poles, Stay Assembly, etc., including formwork and for foundation of GI pipe, Bollard light (as/if required), complete all as specified and as directed.

Cement Concrete 1:3:6 Type C1 (20mm Graded Stone Aggregate) as in Coping of Poles, etc. including Formwork (as/if required), complete all as specified and as directed.

S&F bracket/clamps made of MS flat strips, angle iron suitable size and shape duly fabricated to be fixed with GI bolts/nuts and washer for fixing of GI bracket, PVC conduit, pole junction box or flood lights all as directed and specified

Disconnection existing LT UG cable of any size from pole/Oh line and connect the same to federpiller box by usinf cable glands, lugs etc as required complete all as directed

Supply and replace contactor ML 3 with coil operating voltage 230 Volt complete all as directed

Timer Analog Type Suitable for 24 hours operation of street light of 16 amps capacity. Make : LEGRAND/AVV/CG.

S&F MCB TPN 32 Amps 10 KA, C Curve complete all as directed

Dismantling LT steel tubuler pole of any height by taking out from PCC foundation complete and shifting to other location as directed including fixing the pole in true vertical position including excavation and earth work, PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as base concrete and PCC 1:3:6 type C2 (using 20mm graded stone aggregate) in both foundation and coping of poles all as specified in SSR Part I-2009 and applying two coats of aluminium paint to pole surface complete all as directed by Engineer-in-Charge.

S&F on wall with necessary arrangements busbar chamber 100 amps 4 way 4 pole wall mounted IP -31 , made out of 1.6 mm thick CRCA sheet epoxy powdwer coated single layer operational voltage 440 Volt , Short circuit current capacity 25 KA for 1 Second including necessary cable connections complete all as specified and directed. Note: Quoted rates deemed to be inclusive of necessary fixing arrangement and cable connections , cable glands as required for proper fixing / functioning of Bus Bar Chamber. Make : Havells/ HPL/Standerd,

Supplying and laying of following size HDPE pipe pn 10 ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground , wall , floor complete all as directed

Taking down LED street light fittings of any watt existing position on pole/ tower/highmast , for repair and refix the same after repair complete all as specified and as directed . Note : Spares will be measured and paid separately under relivent items.

Taking down serviceable street light fittings of any watt and type from existing position on pole/ wall/ tower including bracket / clamp and refix the same at new location in pole complete all as specefied and directed.

Taking out unserviceable junction boxes of any type or size for replacement from pole/wall and removing the same from site completeall as specified and directed.

Taking out unserviceable service connection of any type or size for replacement from pole/wall/ OH conductor and removing the same from site completeall as specified and directed. Note : Old serviceable cable, Bricks to be kept separately for reuse against the relivent items.

Taking down old unserviceable post top lantern/bollard / Garden/ Gate light fitting of any watt and type from existing position complete for repair and replacement all as specified and as directed

Supply, fixing, connecting and testing energy saving, environmental friendly long life Varsatile pressure die cast aluminium alloy for housing (heat sink) with IP66 protection road way light fitting with high power LED as light source of capacity 60 watts with warranty option of 2 years with suitable driver and cable gland for maintaining ingress protection with Epoxy powder coated siemens grey finish after phosphochromate treatment, Tempered protective toughened glass,thermal shock and impact resistant fixed to the housing with SS screws , High efficiency long life LED chip in modules with lumen efficacy of >140 lm/W with PC lens and system lumen 6000. Powered by Built-in electronic LED driver with APFC (SMPS based constant current supply), lower THD, Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection. CCT 5700, CRI>70, THD<10%, PF>.95, IP66, IK07.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +50 DEG.C; Input Supply Voltage Range:140-270 V, Frequency : 50-60 HZ, Driver safety requirement standards :IS 15885-2-13, Test report to be submitted for Driver performance requirements as per IS 16104, for Photo bilogical safety norms as per : IS 16108, Certification as per LM 79 for Luminaire , LM 80 for LED Source, with all standard accessories etc, including connection by using 3 core 1.5 sqmm HV Round Cable complete all as specified and as directed including taking down old one . Make: Philips Model No BRP062 LED 65 CW SLA S1 PSU or Havells Cat No. ENDURAPEARLNEOSL60WLED757PASYTOPC or Wipro Cat No. LR02-671-XXX-57-G2 as approved by GE.

All as per item No.78 here in before but 70/72 Watt LED Street light fitting with minimum system lumen out put 9000 lumen. Make: Philips Model No BRP062 LED 84 CW SLA S1 PSU or Havells Cat No. ENDURACITYLINERNEOSL70WLED757PASYBOTG, SURYA Cat No: SLEUL72W IP66 PLX XL or Wipro Cat No. LR02-781-XXX-57-G2 as approved by GE.

All as per item 78 above, but 90 Watt LED Street light fitting with minimum system lumen out put 9000 lumen. Make Philips Model No BRP409 LED 115 CW SLC FG PSU GR V2 or Havells Cat No. ENDURAPEARLPLUSSL90WLED757PASYTOPCASTHO, SURYA Cat No: SLEUL90W IP66 PLX XL or Wipro Cat No. LR02-102-XXX-57-G2 as approved by GE.

All as per item No. 78 here-in-before but Flood light of high power LED as light source of capacity 100 watts. Make: Havells Model No JETAIRISFLS 100WLED757APWBLT G, SURYA Cat No SLEFL100 W IP66 LUMOS MAX or Wipro Cat No. LF20-122-060-57-G2 OR CG Model No : CFS-504-100-30-60D-SL-GL-NSG as approved by GE.

All as per item No. 78 here-in-before but Flood light of high power LED as light source of capacity 120 watts.. Make: Havells Model No JETAIRISFLS 120WLED757APWBLT G, SURYA Cat No SLEFL120 W IP66 LUMOS MAX or Wipro Cat No. LF20-132-060-57-G2 OR CG Model No LFLN-120-CDL/60-M as approved by GE.

All as per item No. 78 here-in-before but Flood light of high power LED as light source of capacity 150 watts.. Make: Bajaj Cat No.BARFEG 150W LED or Havells Cat No. JETAIRISFLS150WLED757PSYMLTG, SURYA Cat No SLEFL150 W IP66 LUMOS MAX or Wipro Cat No. LF20-192-060-57-G2 OR CG Model No LFLN-150-CDL/60-M as approved by GE.

All as per item No. 78 here-in-before but Flood light of high power LED as light source of capacity 200 watts.. Make: Havells Model No JETA VALOURFL200WLED757PINTWBLT G, SURYA Cat No SLEFL200 WATT IP66 LUMOS II or Wipro Cat No. LF20-272-060-57-G2 OR CG Model No LFLN-200-CDL/60-M as approved by GE.

Notes for item Nos 78 to 84 :- (i) LED's used should be the make of Cree/Osram/Lumilieds/Nitchia, (ii) Contractor has to produce LM-79/ LM-80 certificate along with purchase vouchers and Guarantee certificate from Manufacturer. (iii) Surge protection (In-built) of the drive shall not be less than 10 KV (iv) Connection of lights to be given by using 3 core 1.5 Sq m copper wire . quoted rated inclusive of up to 3 m wire against each light . (v) Street lights and flood lights up to 120 watt are to be fitted on pole of height 9 to 11 m. Quoted ratesdeemed to be inclusive of all arrangement required for trhe same. (vi) Flood lights 150 watts and above are to be fitted on High mast pole of height 12.5 to 20 m m. Quoted rates inclusive of all arrangement required for the same

Supply, fixing, connecting and testing post top light fitting in spherical shape polycarbonate PMMA clear diffuser and IP65 protection, new generation energy saving and environmental friendly long life aesthetically desinged aluminium decorative luminaires with high power LED as light source of capacity 1X15/20 watts, fixed on the top of gate piller complete all as specified and directed. Make:- CG Model No LPTH 20 CDL / Havells Cat No. RUBYMINIPT15WLED757PSYMTOPC or Wipro Cat No.LP07-2511-XXX-57-CL as approved by GE.

Supply, fixing, connecting and testing post top light fitting in spherical shape polycarbonate PMMA clear diffuser and IP65 protection, new generation energy saving and environmental friendly long life aesthetically desinged aluminium decorative luminaires with high power LED as light source of capacity 1X35/36/ 40 watts, fixed on the top of gate piller complete all as specified and directed. Make:- PHILIPS Cat Part No BGP300 LED28 757PSU PC IN S1 or CG Model No LPTO 40 CDL/Surya Model No : SLEPT 36 W - ETPP/Havells Cat No. RUBYPT35WLED757PSYMTOPC or Wipro Cat No.LP07-431-XXX-57-CL as approved by GE.

Supply and replace LED Driver suitable for upto 60 watts LED light fittings complete all as specified and directed. Make : Bajaj cat part No BGD 36 185 5Y or techno commercial equivalent model in Philips/Wipro/Havells/ Surya as approved by GE.

Supply and replace LED Driver suitable for upto 72 watts LED light fittings complete all as specified and directed. Make : Bajaj cat part No BGD 36 180 5Y or techno commercial equivalent model in Philips/Wipro/Havells.Surya as approved by GE.

Supply and replace LED Driver suitable for upto 90 watts LED light fittings complete all as specified and directed. Make : Bajaj Cat part No BGD 66 140 5Yor techno commercial equivalent model in Philips/Wipro/Havells.Surya as approved by GE.

Supply and replace LED Driver suitable for upto 100 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and replace LED Driver suitable for upto 150 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and replace LED Driver suitable for upto 200 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and replace LED Driver suitable for upto 120 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

S&F steel light bracket made out of 40 mm bore mild steel GI light grade tubing over all length 1.2 mtr bend to shape as directed including providing two Nos MS flat iron 40x6 mm clamp of appropriate size with nut bolts and washer duly painted with two coat of synthetic enamel paint over a coat of primer (GI surface shall not be painted) complete all as specified.

S&F PVC insulated unsheathed/sheathed cable with stranded Aluminium conductor 1100 Volts grade, flat twin core service cable of size 4 Sqmm conforming to IS:694/1990 with latest amendments ISI including disconnecting/taking out existing unsv/damaged old service cable complete all as specified and directed. Make : Richa/havells/fincab or equivalent as approved by GE.

M&L for drawing two runs of PVC insulated unsheathed single core multi stranded copper conductor FRLS cable of size 2.50 sq mm with one run of PVC insulated unsheathed single core multi stranded copper conductor FRLS cable of size 1.50 sq mm including 20mm dia PVC conduit of dia 20 mm medium gradeexclusive of boxes but inclusive of all tees, bends, elbow, reducers etc and fixing accessories such as couples, lock nuts, saddles, pipe hooks, clamps etc complete all as specified

S & F hot press moulded SMC junction / terminal box of size with internal diamensions of 200 x 140 x 95 mm with hinged door, incl provision of 2 way connector 415 Volts made out of polycarbonate or bakelite and 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable of size of cable lugs/glands, fixied on pole by means of clamps made out of MS flat iron of size 25 mm x 3 mm including dismantling of old unserviceable all as specified and as directed. Make : Hensel/Syntex/C&S/nyptune

M&L cross arm bracing supports, clamp and back plate from structural steel section including nuts & bolts washer, welding, bending, cold or hot drilling holes for bolts in any shape or size as indicated or as directed and including of one coat primer, one under coat and one finishing coat of aluminium paint for making clamp to be used for fixing of flood light /street light on pole..

Supply & Erecting Steel Tubular Swaged Pole Type 410-SP-31 (9.0 METRE long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying Two Coats of Black Bituminous Paint Internally and Externally upto Planting Depth and applying with Two Coats of Aluminium Painting over a Coat of Aluminium Primer (Externally from Top of Coping) including Writing MES Pole No. with Synthetic Enamel Paint (First Grade/quality), complete all as specified and as directed.

S&F lantren of dia 60 CM for fixing of flood light, cap type to be fixed on the top of 9 m SP-31 Steel pole , made of MS pip medium grade dia greater than the top dia of the pole of length 0.35 M supported by MS flat iron of size 50X6 mm 8 nos including two coat of aliminium painting over a coat of redoxide primer complete all as directed

Excavating in Trenches, not exc. 1.50 mtr wide and exc. 1.50 mtr but not exc. 3.00 mtr in depth, for Foundation of Poles, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed.

Supply and lay PVC Insulated , PVC sheathed industrial HV round multicore flexible cable with copper conductor twin core 2.5 sqmm including PVC conduit 20 mm dia medium grade and necessary bends, fittings and fixtures as required for connection of light fittings .

Supply and lay PVC Insulated , PVC sheathed industrial HV round multicore flexible cable with copper conductor twin core 4.0 sqmm including PVC conduit 20 mm dia medium grade and necessary bends, fittings and fixtures as required for connection of light fittings .

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 10.0 Sqmm for connection of light complete all as specified and directed

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 6.0 Sqmm for connection of light complete all as specified and directed

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 2.5 Sqmm for connection of light complete all as specified and directed

S&F LED Bush light red/ blue / green / cool day light in colour 6 watt including necessary fixing arrangement complete all as specified and directed.

Relying of serviceable bricks retrived against iten no 4 for use complete all as directed

S&F Solar LED street light of 30 watt capacity with in built solar panel on the top of the light, inbuilt nicl battery complete all as directed. Make : Luker model No LSTSOL30 or equivalent in Philips/wipro as approved by GE.

Supply and replace contactor ML 2 with coil operating voltage 230 Volt complete all as directed

Supply and Replace MCB SP 32 Amps 10 KA, C Curve complete all as directed

Supply and Replace MCB TP 32 Amps 10 KA, C Curve complete all as directed

S&F locally availablegate / gurden light light best quality metal Silver / metal black Decorative Exterior of size not less than 300 mm X220 mm with and including LED bulb 9 watt suitable for outdoor installation and suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one .

S&F locally availablegate / gurden light light best quality Black Color Steel Shade With Fiber Glass Outdoor Gate Lamp of size not less than 360 mm X250 mm with and including LED bulb 9 watt suitable for outdoor installation and suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one. Make : Jhoomarwala model SKU: (PM-GT-10-BIG) or equivalent as approved by GE

M&L for Taking down UNSV LED Lights and removing Carbon from its connector joints incl replacement of Connecting wire with new PVC sheated weatherproof 3X single core cable for electrical connection and refixing the fitting after repair to its original/New location or as directed by engr-in-charge.(connecting wire will be measured and paid separately only)

M&L for stright Through Joint heat shriankable type suitable for 1100 volt 10 - 25 Sqmm 2/3.5 core complete all as specified and directed

S&F locally available Acrylic glob light best quality clear with and including LED bulb 9 watt of 300 mm dia complete suitable for fixing in 40/50 mm dia GI pipe including necessary connections complete all as specified and directed including taking down old one .

Supply, fixing, connecting and testing decorative LED Bollard light with opal diffuser and aluminium reflector of 8/9/11 watt LED including nut, bolts, washers, clamps etc as in repair complete all as specified and directed. Make:- C&S Cat Part NoLTGLCW9WLED or SURYA Model No SLEBL 6W BLK800 or Havells Cat No. BAMBOOBL8WLED830SSYMTOPCM (1.0) or Wipro Cat No.LB14-131-XXX-65-05 as approved by GE.

SANJEEV CONSTRUCTIONS

SRI SAI RAM ENTERPRISES

omsai thermax engineers

vvcenterprises

Srinivash Engineers

Srinivasa Consructions

DPS sales and services india

Ms V.Prakash

STANDARD AGENCIES

M/S SRIDEVI ENTERPRISES