SPECIAL REPAIRS TO BLDG NO RB 04 AT MCTE UNDER GE MCTE MHOW

Amount

Dismantling asbestos cement corrugated or semicorrugated in Roof covering complete all as specified and directed.

Dismantling/ wall and ceiling boards (fibre pulp, insulation etc) or insulation boards/ slabs complete all as specified and directed.

Dismantling fillets, rails, posts, rafters, purlins etc under 40 Sq cm in section complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15cm thickness (below or above GL) as in plinth protection/path/Hard standing/floor etc. complete removal of debris outside MD land complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc. complete removal of debris outside MD land complete all as specified and directed.

Taking down cement plaster of any description on brick walls, concrete surfaces including racking out Joints, hacking for key, scrubbing down with water, etc. complete removal of debris outside MD land complete all as specified and directed.

Taking down shutter of any description exceeding 1 Sqm and not exceeding 2 sqm each including easing & adjusting shutters and refixing in the same opening complete all as specified and directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exceeding 1.5sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing with prelam sheet complete all as specified and directed.

S&F factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded both side Prelam PVC sheet used instead of plain colour PVC sheet with solvent cement for stiles and top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour Prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable Prelam PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F second class hard wood plain, solid, straight chawkats and frames, wrought, framed rabated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and directed.

S&F 30mm thick second class hard wood, factory made, glazed and skeleton window shutter open rebated prepared to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers including cut and mitred beads for securing glass or wire mesh etc. for windows, the size of members as specified in SSR-2009 Part I clause No 8.20(b) complete all as specified and directed.

S&F factory made 35 mm thick second class hard wood plain framed panelled shutter (two panel) rail and style with lock rail and panel of 12 mm BWP commerical ply . The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F stainless steel wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40 mm fixed with wooden beeds complete all as specified and directed.

S&F butt hinges 100mm mild steel cold rolled, medium weight complete all as specified and directed.

Supply only 50mm mild steel medium weight butt hinges complete all as specified and directed.

S&F 2nd class hard wood small fittings such as brackets of any type latch and hinges block shaped door and window stops and the like incl all necessary labour articles not exceeding 200 Cu cm each in complete all as specified and directed.

S&F 150mm long aluminium, anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 300mm aluminium alloy, anodized, sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F door spring with 300mm mild steel rat rail rod pattern of standard quality including roller and roller plate complete Helical spring) complete all as specified and directed.

S&F mild steel work as in band, strap, hold fast, cleat, hook, hinges, base tie for door frame, support or stay for rain water pipe etc and other similar items conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

Cutting holes in stone/brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) exceeding half brick but not exceeding one brick complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4, type B0 (using 12.50mm graded crushed stone aggregate) as in sub base for floor tiles complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for first or premium quality joint free coloured glazed ceramic tiles (colour as approved laid in pattern as approved by GE ) of size 300x 450mm x 7 mm thick on vertical surfaces such as dados and risers to step etc, set and jointed in neat cement slurry and pointed in coloured cement to match the tiles over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished even and fair including cutting joints and filling with bitumen and sand mixture complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on faces of brick work and finished the surface fair and even without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 surface finished even and smooth without using extra cement. Note :- Rate included for chajja, parapet, curved surface complete all as specified and directed.

M&L for preparation of newly plastered surfaces and applying two coats of distemper oil emulsion over a coat of primer and putty white or tinted on wall surfaces complete all as specified and directed.

M&L for for preparation of newly plastered external wall surfaces and applying two coats of weather proof paint and over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of wall, washing, scrubbing down and stopping of disterpered and painted surface old plastered/ decorated surface and applying two coats wall care putty for smooth finished of the surface and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of wall, washing, scrubbing down and stopping of old treatment and painted surface of plastered/ decorated surface and applying cement base wall care putty and two coats of weather proof paint over a coat of primer on wall surfaces complete all as specified and directed.

M&L for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws complete all as specified and directed.

S&F mild steel work with hollow MS tubular section square or rectangular section as rafter/purlin including necessary welding bolting complete with using ERW or induction butt welded tubes confirming to IS complete all as specified and directed.

M&L for preparation of old painted surfaces of steel of any description and applying one coat of synthetic enamel paint over 10cm width or girth complete all as specified and directed.

M&L for preparation of new wood surfaces and applying two coats of synthetic enamel paint over a coat of pink primer over 10cm width or girth complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and directed.

M&L for providing brick work in cement mortar 1:6 , 23 cm thick and 15cm high along external walls to fill the gap including plastering 15mm thick in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

S&F in true horizontal level 600mm x 600mm, false ceiling system hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x38 mm, having 0.25mm gauge at every 1200 mm centre to centre maximum and rotary stitched cross tee of size 24 x 38 mm having 0.25 mm gauge at every 600mm c/c and sub cross tee of size 24 x 38mm, having 0.25 mm gauge at 1200 mm c/c and wall angle of size 19 x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The abovegrid is suspended at every 1200 mm c/c in both directions using 2.0mm thick pre-straightened GI wire. laying calcium silicate fissured pattern semi perforated butt edge ceiling tiles , of size 600mm x 60mm x 6mm having thermal conductivity K=0.15 W/mOK, having fire performance (BS-476) complete all as specified and directed.

Taking up or down steel tubing and connections for bore of tube 15 mm complete all as specified and directed.

Taking up or down steel tubing and connections for bore of tube 20 mm, complete all as specified and directed.

S&F 20mm steel water tubing, medium grade (ISI marked) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F 15mm steel water tubing, medium grade (ISI marked) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Cutting chases in brick wall built in cement mortar for concealed water tubing and making good with cement mortar in 1:4 ,cutting depth not exceeding 10 cm complete all as specified and directed.

S&F in repairs bib tap fancy type chromium plated with long shank with flange screwed for iron pipe 15mm borecomplete all as specified and directed. Make Jaguar cat part No DRC - 370370 or equivalent in Parryware as approved by GE.

S&F in repairs chromium plated swan neck tap for WHB fancy type cast copper alloy, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm dia bore pipe complete all as specified and directed. Make Jaguar cat part No CON-123BKN or equivalent in Parryware as approved by GE.

S&F in repairs stop valves/angle cock, 15mm dia pipe cast copper alloy, fancy type, chromium plated with long shank and cup screwed down, high pre-ssure, for iron pipe or for unions complete all as specified and directed. Make Jaguar cat part No - FLR - 5053N or equivalent in Parryware as approved by GE.

S&F brass chromium plated corner glass shelf with bracket complete all as specified and directed. Make- Plumber cat No.U-0918 or equivalent in Jaquar /Parco/MARC/ESS as approved by GE.

S&F sheet glass shelf assembly consisting of 5.5 mm thick glass shelf 120mm wide with chromium plted bracket gouard and railing 600 mm long complete all as specified and directed. Make- Plumber cat No.U-0918 or equivalent in Jaquar /Parco/MARC/ESS as approved by GE

S&F in repairs soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs vitreous china wash down water closet (padestal pattern) white/coloured (excluding flushing cistern and flush pipe) including white/any colour PVC seat cover white closed pattern with recessed bottom and connection to drain or out going pipe and flushing pipe complete all as specified and directed.

S&F in repairs 10 ltr capacity PVC Low level flushing cistern including 32mm dia PVC flush pipe, fixing in position with PVC connection pipe of 15mm x 600mm long etc complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, oval type white ,flat back, size 550x400mm incl 32mm dia polythelene waste pipe and 32mm dia CP waste coupling, and incl bracket necessary packing and chain and plugs and porcelain stopper complete all as specified and directed.

Dismantling water tanks and removing to store exceeeding 250 & not exceeding 1000 litres capacity complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc and hoisting if required and re-fixing in position exceeding 500 & not exceeding 1000 litres capacity complete all as specified and directed.

S&F in repairs 20mm dia ball valves of PTMT high pressure, with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15 to 25mm to 142 - 455 gms) complete all as specified and directed.

S&F in repairs shower rose with brass chromium plated shower rose with or without swivel joints, 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs brass chromiun plated tubular towel rail, 20mm dia ‘D’ type, 60 cm long between flanges complete all as specified and directed. Make Jaguar cat part No - .ACN 1111NM or equivalent in Parryware as approved by GE.

S&F in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to floor/ walls etc complete all as specified and directed.

S&F repairs PVC (SWR) bends 110mm dia any radius with access door complete all as specified and directed.

S&F repairs PVC (SWR) junction single,(Single T) 110mm dia equal or unequal with access door complete all as specified and directed.

S&F repairs PVC (SWR)vent cowl 110mm bore complete all as specified and directed.

M&L for 18-20 mm thick machine cut mirror polished kota stone slab flooring with rounded edge laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 15mm thick cement screed bed (1:6) complete all as specified and directed.

Cutting and mirror polishing of existing kota stone flooring complete all as specified and directed.

M&L for brick work in modular size with sub class "B" bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down carefullycopper/aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, sockets ,ceiling rose, light fittings etc, and making good the disturbed surface of walls and floors etc all as directed by Engr-In-Charge.

Taking down carefully copper/aluminium sub-main wiring any type and making good the disturbed surface of walls and floors etc all as directed by Engr-In-Charge.

Taking down carefully MCB DBs/sheet metal earth plug socket any size and any type including MCBs any type and making good the disturbed surface of walls and floors etc all as directed by Engr-In-Charge.

Taking down existing electric ceiling fan in position and re-fixing the same after completing B/R works including painting of the same with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter, with and including providing three core flexible copper cable of size 1.5 sqmm for connection from ceiling rose complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with PVC insulated FRLS PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area for phase/neutral in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in Surface conduit wiring system and making good disturbed surface of wall (Wiring on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including galvanised boxes with bakelite sheet for mounting switches, sockets, fan regulators etc for the following :- Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Asian

One light/fan point controlled by one switch

One 5amps socket out let point controlled by one switch on same board with other switches.

One 5amps socket out let point on independent board controlled by one switch.

All as per item No 75.00 above but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F switch piano type 05 Amps single pole, one way complete all as specified and directed.

S&F socket outlet, multi purpose, 2 in 1, 3 Pin 5 Amps complete all as specified and directed.

S&F socket outlet, multi purpose 2 in 1 , 5 /15 amps type complete all as specified and directed.

S&F switch 15 Amps single pole, one way complete all as specified and directed.

S&F electronic fan regulator step type complete all as specified and directed.

S&F ceiling rose surface bakelite three terminal ,white in colour complete all as specified and directed.

S&F lamp holder insulated body with round back plate, white in colour complete all as specified and directed.

S&F LED bulb of 7 watt, Of base B-22, suitable for lamp holder complete all as specified and directed.

S&F in repairs LED batten for retrofit type LED tube upto 1x22 Watt, without LED tube rod,pre-wired for LED tube, complete with all accessories duly connection with three core flexible copper cable and duly fixed on two Nos PVC square boxes complete all as specified and as directed. Make:- Havells, Cat No. LHFXCEP1TNNW020 or equivalent in Crompton/Wipro/Phillips as approved by GE.

S&F in repairs retrofit LED tube light T-8 type, 1x20 Watt, 6500K with single side connection complete all as specified and directed. Make:- Havells, Cat No. LHLDEFXD5L8R020 or equivalent in Crompton/Wipro as approved by GE.

S&F in repairs LED tube light fittings 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells. Cat No. LHEXBLP7IN1W009 OR equivalent Crompton/ Phillips/Wipro as approved by GE.

S&F in repairs wall light fittings suitable for & including LED bulb of 7 watt, including connection with all necessary fixing accessories complete all as specified and directed by Engr-in-Charge. Make :- Havells Cat No. LHDL07150099 or equivalent in equivalent in Crompton, Philips.

S&F for energy saving recess/surface mounted luminaire 36/40 W, high efficiency PMMA diffuser gives soft glare free light, suitable for 600X600 ceiling cut out, recess mounted 36W LED luminaire in MS housing (2'X2') incl Provn of three core cable of copper conductor of size 1.5 sqmm, making necessary electric connetion from ceiling rose to fitting terminal , fixing the fitting on ceiling including cutting, grooving with proper finish and making good, disturbed surface with all fixing arrangement complete all as directed. Make: Havells Cat No.VENUSNEOHE2X2PLR18-42WLED865MOD Or equivalent to crompton/Wipro/phillips as approved by GE.

M&L for sub main wiring with two runs of single core PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including concealed non metallic rigid PVC conduit of not less than 25 mm dia including one run of PVC insulated unsheathed 4 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly in concealed wiring system by cutting of wall and making good disturbed surface of wall all as specified and directed. Note: Two runs of single core PVC insulated copper cable 4 sqmm size with one run of 4 sqmm copper earth cable and one run of PVC conduit 25 mm dia shall be measured as one unit length for purpose of payment.

S&F in repairs double door SPN DBs eight ways of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed.

S&F MCB SPN 6 to 32 amps 10 KA, 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F in repairs MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F (In building peripheri) energy efficient, compact street lighting 25 Watt LED with deep drawn Alluminium housing complete with conncting wire and provision of GI bracket, clamp, nuts, bolts grouted in wall including all fixing arrangement. Make: Havells Cat No.ENDURAPEARLSL25WLED757 SASTOPCMP or equivalent to Crompton /Wipro /Phillips as approved by GE.

M&L for sub main wiring with two runs of single core PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including concealed non metallic rigid PVC conduit of not less than 25 mm dia including one run of PVC insulated unsheathed 6.0 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly in concealed wiring system by cutting of wall and making good disturbed surface of wall all as specified and directed. Note: Two runs of single core PVC insulated copper cable 6 sqmm size with one run of 6 sqmm copper earth cable and one run of PVC conduit 25 mm dia shall be measured as one unit length for purpose of payment.

M&L for earthing complete with galvanised steel earth p;ate 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised Iron Wire of size 4 sq mm as earthing lead by means of bolts, nuts, cheek nut and washers of galvanised iron or steel besides at all joints as shown in Electrical Plate No-3 of SSR Part I and including excavation and earth work GI pipe 20 mm dia light grade protection pipe and including chorcoal filling common salt ,PCC 1:3:6 type CI using 20 mm graded stone aggregate chamber and MS angle iron frame 40x40x6mm and RCC cover 40mm thick (1:2:4) type B-1 using 20mm dia graded stone aggregate reinforced with 6mm dia round bars @ 75 mm c/c both ways with MS handle 12mm dia, CI funnel and wire mesh 20mm dia GI pipe medium grade for watering and connected to earth Test point (Including testing complete all as specified and directed).

M/s Himgiri construction

M/S GARG CONSTRUCTION

M/s Shree Ganesh Traders

Jamna Constructions

M/S Sunshine Construction

ckasati

AGARWAL BUILDERS

Goyal Construction