Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹9.7 LAccepted-AOC | L1 | Accepted-AOC L1 | |
| 2 | L2₹9.8 L+₹8,330 (0.85%)Rejected-Finance | L2 | Rejected-Finance Other than L1 | |
| 3 | L3₹11.2 L+₹1.5 L (15.3%)Rejected-Finance CC III 28A JANTA BHAWAN ROAD SIRSA HARYANA 125055 | SIRSA | HARYANA | 125055 | L3 | Rejected-Finance Other than L1 | |
| 4 | L4₹14.5 L+₹4.8 L (49.2%)Rejected-Finance NOT FOUND | L4 | Rejected-Finance Other than L1 |
Tender Value
₹17 L
EMD Value
₹34,000
Closing Date
18 May 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (AF) SIRSA
GE (AF) SIRSA, HARYANA-125055
POST ATT TO CERTAIN BUILDINGS AND REPAIRS TO CHAJJA FACIA, CEILING, BALCONY AND CONNECTED WORKS IN DOMESTIC AREA AT AF STN SIRSA
2024_MES_651463_1
GE/SRA/T-24/2024-25
Open Tender
Miscellaneous Works
Item Rate
240 days
GE (AF) SIRSA
PLEASE REFER TENDER DOCUMENTS
8 documents required · 8 mandatory
₹500
GE (AF) SIRSA
₹34,000
Yes
3 Jun 2024
27 Apr 2024
20 May 2024
27 Apr 2024
18 May 2024
6 May 2024
Amount
M&L for providing and injecting chemical emulsion for post construction Anti-Termite treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging, 12mm dia holes with cement mortar 1:2 to match the existing surfaces complete all as specified and directed.
M&L for providing and injecting chemical emulsion for treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar (1:2) to match the existing floors complete all as specified and directed.
M&L for providing and injecting chemical emulsion for treatment of voids in masonry using chemical emulsion @ one litre per hole, at 300 mm intervals including drilling holes at 45 degrees and replugging them with cement mortar (1:2) to match the existing surface complete all as specified and directed.
M&L for providing and injecting chemical emulsion for post construction anti - termite treatment at points of contact of wood work by chemical emulsion ( in oil or kerosene based solution) @ 0.50 litres per hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same incluidng repainting the joinery surface to match the existing surfaces complete all as specified and directed.
GENERAL NOTES FOR ITEM NO 01 TO 04:- 1) Anti-termite treatment work shall be carried out through authorised applicators having valid license frm IPCA. 2) Anti-termite chemical shall be procured in sealed containers and kept in custody of Engineer-in-Charge. Material would be issued by JE/AGE as per site requiredment. 3) Quoted rate shall be deemed to be inclusive of the cost of all T&P, protective gear and safety arrangements required for satisfactory execeution of the work.
Demolition Cement Concrete (Reinforced) of Roof, Floor (other than Ground Floor) Beam, Staircase, Landings, Chajjas and similar work (reinforcement cut as required to facilitate demolition) and removing debris, etc. to Outside MOD Land, complete all as specified and directed.
M&L for Cutting holes into or through brick walls built in cement mortar or cement lime mortar and making good in 1:3 or cement concrete 1:2:4 type B1 as required for superficial area not exceeding 150Sqcm complete all as specified and directed by Engineer-in-charge
M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed.
S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.
M&L for repairing of RCC projection, chajja, roof facia, column etc by necessary preparation i.e. scraping, cutting, chiselling and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces, then applying one coat of cement slurry and filling the surface with cement concrete 1:1.5:3 using 12.50mm graded stone aggregate, reinforced with welded mesh and Surfaces to be finished even and smooth without using extra cement incl applying a Coat of Chalk Whiting (as Preparatory Treatment) and applying Two Coats of Exterior Emulsion Paint over a coat of cement primer with approved Tint as per manufacturer's instructions compete all as specified and directed. NOTE:- (i) Site for application is at various locations in patches and height varies up to 12M. (ii) Proper stable Scaffolding is must for working for the safety of resident of bldg and worker. Cost of all types of formwork, scaffolding & safety gear and welded mesh shall deemed to be included in quoted rate.
Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc and removal of debris outside AF land complete all as specified and directed.
M&L Rendering (Internal) 15mm thick, in cement mortar 1:6 on Brick Walls or on Concrete Surfaces, Plastered Surfaces finished Even and Smooth without using Extra Cement complete all as specified and as directed.
M&L preparing new Plastered surfaces of Walls by applying 1.5mm Wall Putty including Rubbing down with Sand Paper to obtain a Smooth Finish Surface and applying Two Coats of Acrylic Distemper (as approved) over a Coat of suitable Primer with rollers, complete all as specified and as directed.
M&L for Rendering 5.0mm thick in cement mortar 1:3 on Concrete Surfaces of Ceilings, Plastered Surfaces finished even and smooth without using extra cement complete all as specified and as directed.
M&L for preparing newly Plastered surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.
M & L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (as per manufacturer's instructions) on brick/stone walls or concrete surfaces finished even and fair (upto any height) for external surfaces complete all as specified and as directed. Note : Water Proofing compound shall be measured and paid seperately as "Supply only".
Supply only Liquid Water Proofing Compound, conforming to IS and/or as approved, complete all as specified.
M&L for preparation of newly plastered surfaces and applying exterior wall putty 1.5 mm thick for smooth surface and finished with two coats of exterior acrylic emulsion paint (having anti-dust & anti-algae properties) over a coat of suitable exterior primer, applied with rollers to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufactuirer's instructions, upto 4 storey height complete all as specified and as directed.
M&L preparing old Decorated/Treated Plastered surfaces of Exterior Walls upto Four Storey by brooming down or steel wire brushing and scraping down, filling of cracks with suitable paste and applying with rollers One Coat of Exterior Emulsion Paint (having anti-dust & anti-algae properties) with approved Tint (as per Manufacturer's instructions), complete all as specified and as directed.
-ditto- but with Two coats of Exterior Emulsion Paint complete
M&L preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.
M&L preparing Old Decorated/Treated Surfaces of Ceiling of any description and applying One Coat of White Wash, complete all as specified and as directed.
M&L preparing old Distempered surfaces of Walls by brooming down or steel wire brushing and scraping down and filling the existing Nails/ Screw Holes, etc. and applying with rollers one Coat of Acrylic Distemper (as approved), complete all as specified and as directed.
M&L for Reinforced Cement Concrete 1:2:4, type B-0 (12.5mm graded stone aggregate) in Slabs suported on walls complete all as specified and as directed. NOTE: MS reinforcement shall be measured and paid sepertely.
M&L Formwork to Chajja, slab, landing through and Similar Items including Edges for Rough Finished Flat Surfaces of Concrete, complete all as specified and directed.
M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and directed.
M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm dia, complete all as specified and as directed.
-ditto- but with 6-8 mm dia TMT bars
M&L preparing new or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed.
M&L preparing Old Treated/Painted Steel and Iron Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.
NISHTHA BUILDERS
M/s Satguru Traders
shiv shanker enterprises
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .