SPECIAL REPAIR TO BLDG NO T-54-23, PERIMETER WALL, FENCING, AND OTHER MISC BRICKS WORKS UNDER AOR OF AGE BR-I OF GE (WEST) PATHANKOT

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for cement concrete complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc and removing of debris out of MoD land complete all as specified and as directed.

M&L for cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregates as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Providing precast cement concrete 1:2:4, type B1 (20 mm graded aggregate) set in CM 1:4, as in cover slabs (for manhole, drains etc) with plain fair faces, complete all as specified and directed.

Providing 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) precast cement concrete louvres and jallies set in CM (1:4) , 25mm thick (measured solid), including all mould- ings, frames and demolition of existing louvres/jallies complete all as specified and directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for formwork to sides of flat, rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical to batter complete all as specified and directed.

M&L for formwork to sides and soffits of flat, rough finished surfaces of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for formwork to sides of square, rectangular or polygonal, rough finished surfaces of concrete of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for RCC, M-25 (design mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs and mass concrete complete all as specified and directed.

M&L for RCC, M-25 (design mix) using 20 mm graded stone aggregate in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed. (Note:- WPC shall be measured and paid separately

Rendering 15 mm thick on stone masonary surfaces or surfaces of fair faces of brick work or concrete surfaces in cement mortor 1:4 finished even and smooth without using extra cement complete, incl mixing with WPC (as per manufacturer’s instructions) complete all as specified and as directed. (Note:- WPC shall be measured and paid separately

Rendering 15 mm thick on stone masonary surfaces or surfaces other than fair faces of brick work or concrete surfaces in cement mortor 1:4 finished even and smooth without using extra cement complete, incl mixing with WPC (as per manufacturer’s instructions) complete all as specified and as directed. (Note:- WPC shall be measured and paid separately

Supply only integral water proofing compound as directed by Engr-in-charge.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, over and including a coat of alkali resistant priming paint complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, over and including a coat of alkali resistant priming paint complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted surface of steel of any discription exc 10cm width or girth and providing one coat of synthetic enamel paint complete all as specified and directed.

S&F in repair galvanized, 2 strand, steel barbed wire, 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line wire to be measured) complete all as specified and directed.

S&F Rolled mild steel framed work as in doors gates of angle or other section with gusset plates, rails braces etc complete ,drilled for fixing of steel sheeting or other covering, doors etc to be prepaired for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (including of steel sheeting or other covering, running rails & guides) & hanging also fastening and fixing complete GDE Fe 410-0 or Fe 310-O incl framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc and ornamental and intricate design all as specified and directed.

S&F mild steel work as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled & countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete & screwing etc. wind ties for roof including securing bolts; posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., & similar work conforming to Fe 290-0 Gde E-165 angle horn 'Y' shape complete all as specified and directed .

Material and labour for Providing and fixing concertina coil fencing with punched tape concertina coil 610mm dia incl taking down old concertina coil, with following specifications:- (i) Coil Dimension :- (a) Coil opening diameter (610mm+20mm, -0mm) before stretching. b) When stretched upto 6 meter length -coil diameter not less than (580mm+20mm-0mm) c) Coil having 50 Nos spiral turns & 129 nos clips in 06 meter length and weight not less than 9Kg + 5% excluding spike and handles (ii) Razor barb BTO-22 a) Barb thickness 0.5mm (+- 0.05mm) b) Barb width 15mm (+-1mm) c) Barb length 22mm (+-1mm) d) Barb spacing 35mm (+-1mm)

e) Steel strip (punched tape/RBT)= The punched tape shall be CR3 grade cold reduced low carbon steel as per IS 513:2008 with pre painted Aluminium Zinc alloy in accordance with IS 15965:2012/AZ150/Class 3. (iii) Spring Core wire (a) Nominal dia of uncoated wire = 2.59mm (+-0.035mm) b) Galvanisation = The core wire should have thickness of hot dipped galvanised zinc to 290 g/m2 minimum as per the specification BS EN ISO 1461, Similarly, Indian Specification IS 4826. d) High tensile strength not less tann 1620 N/Sqmm iv) Heavy duty "J" clip for attachments" a) Material= SS 304 Stainless steel b) Dimension= 29mm x 8mm x 1.6mm

M&L for Plain cement concrete 1:3:6 using (20mm graded aggregates) as in coping etc including necessary form work complete all as specified and directed.

M&L for brocken glass coping 20 mm thick on top of walls in cement mortor 1:3 complete all as specified and directed.

Dismantaling stone slabs and tiles of any description or thickness in floors, aprons etc, complete all as specified and directed.

M&L for 20 mm thick black Granite (of any type) work (table rubbed and polished) in steps,jams,pillars,window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 10 mm thick rendering in CM(1:4) complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position in framed work complete all as specified and directed.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete hallow section/ conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, including ridges complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

All as per srl item No. 38.00 here-in-before but plain sheet as in ridges, gutters, facia etc complete all as specified and directed.

M&L for RCC 1:2:4, type B-1 nominal mix (20mm graded crushed stone aggregates) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Dismantaling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F for suspended false ceiling system using chicago metallic (E grid)exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

Supply and fixing joint free non skid coloured Ceramic tiles 07mm to 08mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Supply and fixing joint free non skid coloured Ceramic tiles 07mm to 08mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as dado etc and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed.

M&L for Machine pressed precast interlocking paver blocks any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade with gray cement and pigment complete all as specified and directed.

M&L for sand cushioning for interlocking paver block complete all as specified and directed.

M&L for PCC 75 mm thick 1:4:8 type D2 using (40 mm graded aggregates) as in sub base of floor complete all as specified and directed.

M&L for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified and directed.

M&L for rendering 15 mm thick on brick wall finished fair & even in CM (1:6) complete all as specified and directed.

Material and labour for preparation of newly plastered internally surfaces of wall and applying min 1.5 mm thick wall care putty on the surfaces & making the surface absolutely smooth surface and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion finished without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for complete removal of existing treatment internally surface of wall and applying min 1.5 mm thick wall care putty on the surfaces and making surface absolutely smooth and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion without any brush marks on the surface in any tint including necessary scaffolding up to four storeys height of bldgs if required, Shade/colour shall be approved by GE, all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

S & F pressed steel frames 125 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as spd and directed.

M&L for cement concrete 1:3:6, type C-0, using 12.5mm graded crushed stone aggregate as in back filling of hollow portion of frame with plain cement concrete and for fixing of hold fast complete all as specified and directed.

S&F of 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, confirming to IS- 2202(Part-I-1999) , ISI Marked complete all as specified and directed

S&F of 35mm thick factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. (Note: wire cloth shall be measured and paid separately.)

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

S&F of 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding to steel frames complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F of Steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of hollow' section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10 mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, tarred hold fasts, PCC bed blocks for fixing hold fast , including plain/figured glass and wire mesh complete all as per details shown in drawing No CEPZ/TD-245/01 sheet No 1/1 and CEPZ/TD-246/01 sheet No 1/2 & 2/2 including taking down existing spoiled and unserviceable windows/ ventilators of any type (wooden/steel) complete all as specified and directed .

S & F 100 mm long Butt hinges type C-21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

Supply and fixing Aluminium, anodised, barrel tower bolts of extruded section and fixed, Length of bolt in 150mm complete all as specified and directed

Supply and fixing Aluminium handles, cast type, anodised Size of handle in 150mm complete all as specified and directed.

Supply and fixing Aluminium alloy, anodised, sliding door bolt of size 250mm long with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified.

Supply and fixing Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor Overall length of cover plate 140mm complete all as specified and directed.

S&F in repair harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, Bracke sketch fitting, ceiling roses, lamp holders, brackets, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc as per existing finishes complete all as specified and directed by EIC. Note:- The damaged surfaces to be made good with plastering (1:6). & applying finishes in required coats to matching with existing surfaces as directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible.

M&L for Point wiring with 1.5 Sq. mm (nominal area) FRLS PVC insulated and unsheathed multistranded copper conductor cable 1100 Volts grade drawn through and incl PVC rigid concealed conduit (ISI Marked) suitable size with all accessories having thickness not less than 1.8mm incl sheet steel/ CI terminal box of adequate size having thickness not less than 2mm including 3mm thick hylem/masonite sheet including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor multistranded cable of green colour as earth conductor connected to common earth dolly complete all as specified and directed for one light / fan point controlled by one switch 5 Amp, SP, one way, 240 Volts complete all as spd and directed. Note: 1. Connections of cable with MCBs/Switch Sockets shall be done through proper size copper/brass thimbles. 2. Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit in not feasible. 3. Proper colour code will be used for wiring as per the electrical rule and as directed.

All as per Srl item No 69 here-in-before but for one 5 pin 5 Amp socket outlet point on inependent board controlled by one switch SP, one way 5 Amp, 240Volts.

All as per Srl item No 69 here-in-before but for one 5 pin 5 Amp socket outlet point on same board controlled by one switch SP, one way 5 Amp, 240Volts.

M & L for point wiring with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed. Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green).

S & F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

M & L for ceiling rose, PVC/Polycarbonate, insulated body, surface Bakelite 65mm dia three terminals all as specified and as directed.

Supply and fixing ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S & F in replacement of CFLs with LED Lamp, B22 type ,14 watt,complete all as specified and directed.

S&F 20W surface / wall mounted batten LED luminair, extruded aluminium housing with PC diffuser and ind electronic driver with high efficiency long life, CRI = 80 (Minimum), PF > 0.95, luminous efficacy > 100 lumens/Watt operating voltage 140V-240V, CCT (K) > 6500, THD < 10% complete including 20W LED tube rod with all accessories internally prewired and including connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose to connector of LED fitting complete all as specified and directedories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete Make of LED Fitting:- CROMPTON DMLN1LT8-16 or Technocommercially equivalent in any of the make mentioned in the list of product.

S&F in replacement Energy saving, surface mounted, bulk head LED luminaire 10 W with PDC aluminium housing and polycarbonate diffuser with IP 66 protection complete including connecting up with three core twisted flexible copper conductor cable of suitable size.all as specified. Make :- CROMPTON CAT Part No. LBHP-10-CDL or Technocommercially equivalent in any of the make mentioned in the list of product.

Taking down ceiling fan by disconnecting the electric connection and dismantling the blades and removing from ceiling/roof of bldg by descrewing the nut, bolt etc complete all as specified and directed.

M&L for Rehanging only of ceiling fan and connecting up including provision of PVC insulated and overall sheathed flexible copper conductor cable 3 core of size 0.50Sqmm from ceiling rose or connector to fan including minor repairs such as replacement of locking pin, reel insulators, bolts, nuts etc and spraying one coat of synthetic enamel paint of required colour complete all as specified and directed.

S & F of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

M & L for MCB SP 240 volts any rating from 6 to 32 amps, 'B' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M & L for MCB SPN 240 volts any rating from 6 to 32 amps, 'B' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M&L for sub Main Wiring with 2 run of 6 Sqmm FRLS PVC insulated and unsheathed, multistrand copper conductor cable using colour code for phase red and neutral black with and including 6 Sqmm FRLS PVC insulated and unsheathed multistrand copper conductor cable in green colour as earth conductor connected to common earth dolly, drawn in and including concealed PVC rigid conduit of suitable size having thickness not less than 1.8mm (ISI marked) with and including all accessories complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match existing surface including taking down of existing unserviceable surface/cocealed sub main wiring any type complete all as specified and directed. Note: Two run of submain wire (phase and neutral), and one run of earth including PVC conduit and accessories will be measured as one run.

S & F of bldg secuirty light fitting energy saving high efficiency LED street light fitting 30 Watts, 5700 K, IP 66, having in built 4 KV surge protection and external 10KV surge protection, IK 09 pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including bracket of size 32 mm dia GI pipe medium grade bent to shape having length on less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (Earth pit not less than 2.25 metre deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanised earth lead wire 4.0 mm dia as earth lead by means of bolts, nuts,check nuts and washers of GI upto test points, GI tubing 15 mm bore light grade protection pipe, GI watering pipe 20 mm bore light grade with funnel and wire mesh, 15 cm thick a layer of charcoal and, salt packed around the earth plate and pit cover precast RCC 1:2:4 (nominal mix) reinforced with XPM having weight not less than 4 Kg Sqm including suitable handle of 6 mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil removal of surplus soil to to a distance and n.exc 50m and connecting to test point and testing on completion complete all as shown onn electrical plate No.03 of SSR Part-I (2009) complete all as specified and as directed. (Note :- Excavation and earth work is deemed to be included in the rate quoted)

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 1,12,348.00). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 3% (Three percent) of the accepted contract sum shall be delivered by the successful bidder immediately after the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249

M/S RUDRA CONSTRUCTION CO

M/S Raghuvanshi Builders

VIKRAM SINGH MANHAS

M C ENTERPRISES