SPECIAL REPAIR TO CERTAIN B/R WORKS AT BLDG NO P-08 AND P-15 AT AFS KANHERI HILLS, PROVN OF TILING, SHED and MODULAR KITCHEN CABINET/RACKS AND CERTAIN MINOR WORKS AT AFS KANHERI HILLS UNDER GE AF THANE

Amount

Dismantling floor, hearth or wall tiling including cement morter beddind (but not backing removing seviceable tiles to store and rubbish off the premises ,complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.complete all as specified and as directed.

Material and labour for brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed.

M&L for Vitrified Ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 20mm thick screed bed in CM 1:4 for laying floor finishes all as specified and directed.

M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in vertical position as dado/skirting. set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thck in CM 1:4 as backing coat to receive tiles in vertical position as dado/skirting complete all as specified and directed.

Material and labour for non-skid coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exceeding 0.06 Sqm but not exce 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in CM(1:6) complete all as specified and as directed.

M&L for Glazed ceramic coloured (colour & shade as approved) tiles non skid of size 400x400x7mm thick as in floor set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Ditto as per Srl item No 7.00 above but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

M&L for Glazed ceramic tiles, coloured (colour as approved), of size 300x200x7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Material & labour for Glazed ceramic coloured tiles in vertical surfaces 350x250X7/ 450x350x7 mm thick in skirting /dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortor complete all as specified and as directed.

M&L for Granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform sand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to matchwith shade of granite including 15mm thick screed bed in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L for Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-In- Charge.

Demolition of un-reinforced cement concrete in any position , complete all as specified and directed by Engineer-in-Charge

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified.

Demolition RCC Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work , complete all as specified and directed by Engineer-in-Charge

M&L for RCC(Nominal mix) in 1:2:4 using 20mm graded aggregate nominal mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like , complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work , complete all as specified and directed by Engineer-in-Charge

M&L for formwork to edges of concrete flats, and similar work , complete all as specified and directed by Engineer-in-Charge

M&L for use & waste wooden form work (rough finished surfaces ) to sides & soffits of Chajjas, parapets & facia and similar work n. exc 200 mm thick, complete all as specified.

M&L for RCC type B1, 1:2:4 (20 mm graded Stone agg) as in Chajja, facia , complete all as specified.

Mild steel TMT Mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips , complete all as specified and directed by Engineer-in-Charge.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

Ditto as per Srl Item No 23.00 above but size exceeding 1.5 Square metre and not exceeding 4 Square metre each , complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description of exceeding 1 sqm but not exc 2 Sqm complete all as specified and as directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

Ditto as per Srl Item No 26.00 above but size 125x60mm with double rebate.

M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work , complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-I using 20mm graded stone agg. As in bed block of hold fast coping incl. necessary form work , complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick IInd class HW rail and style plain framed panelled factory made shutter (Two panel) with lock rail and panel of 9mm BWP,commercial ply or 12mm veneered particle beard with commercial veneering on both faces. The size of rail and stile as per IS :1003 (Part-I) kiln and chemically pressure treated , complete all as specified and as directed by Engineer-in-charge..

S&F in repair for 35mm thick IInd class hard wood glazed and skelton shutters divided into squares with plain chamfered or reounded miltred and related sash bars number to received glass gauze etc edges of framing plain chamfered or reounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.20(a) supplied and fitted to chawkats , complete all as specified and as directed by Engineer-in-charge.

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2020)., complete all as specified and directed by Engineer-in-Charge.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved.

S&F for 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S&F for 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified.

S&F for 100 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket tc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, luminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM Rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved esign/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each pane , complete all as specified and as directed by Engineer-in-charge.

S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with powder coated aluminium beading/wood beading , complete all as specified and as directed by Engineer-in-charge.

S&F in Repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples , complete all as specified and as directed by Engineer-in-charge.

S&F for 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S&F for 150 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed , complete all as specified and as directed by Engineer-in-charge.

M&L for Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for MS railling work , complete all as specified and as directed by Engineer-in-charge.

Dismentling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings , complete all as specified and as directed by Engineer-in-charge.

S&F Framed mild steel work of grade E-165 (Fe-290) as in framed work such as doors, gates or frame for cooler stand with gusset plates, rails, braces etc, drilled for fixing of sheeting or other covering of door etc, to be prepared for hanging or sliding etc including either hooks and hinges or steel hanging door fittings and hanging and fixing complete all as specified.

M&L for Pre painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Pre-painted galvalume aluminum zinc coating GI based curved/plain corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer complete all as specified.

S&F ,in repair, Drapery curtain rod/ Harrison rails of anodised aluminium alloy complete with MS brackets golden colour rings and sode caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw ,complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified.

Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified.

Fixing only, after cleaning old serviceable steel water tubing retrived from taking down, for 15mm bore and connections in new or old position using new fittings complete all as specified.

Fixing only, after cleaning old serviceable steel water tubing retrived from taking down, for 20mm bore and connections in new or old position using new fittings complete all as specified.

S&F 300mm Mild steel helical door spring including roller and roller plate complete all as specified.

S&F in repair, Towel rail, 19mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs as in repair complete all as specified.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified.

S&F in repair 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified.

S&F 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified.

S&F in repair stop cock 15 mm cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe etc.,complete all as specified and as directed by Engineer-in-charge.

S&F in repair Bib tap of CP brass, 15mm bore, fancy type screwed down, screwed for iron pipe or for brass ferrule complete all as specified. .

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white incl. Seat and cover (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed

S&F 15mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) fixed in repairs complete all as specified.

S&F in repairs table top wash basin 560mm x410mmx 180 mm vitreous china (white) including PTMT waste fittings 32mm bore size, 32mm bore PVC waste pipe, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing , complete all as specified. Make : Prayag (Cat No 4790) / Cera or equivalent as per aprroved make list.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm etc suitable for 15mm bore of pipe complete all as specified.

S&F 50 mm Low density polyethelne (LDPE) pipes of pressure rating 6kgf/sq. cm ,complete all as specified and as directed by Engineer-in-charge.

S&F, in repair, 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass ,complete all as specified and as directed by Engineer-in-charge.

S&F in Repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Dismantling CI pipe alongwith fittings of 75/100mm dia, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. (fitting measured separately).

S&F in repairs 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent including jointing to waste pipe in run lead as complete all as specified.

S&F 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal

S&F 75 mm bore PVC (SWR) bends any radius

S&F, in repair,110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes complete all as specified.

S&F ,in repair,PVC (SWR) branch pieces, double 'Y' shape (equal or unequal) or with parallel branches 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F,in repair, PVC (SWR) junction, single 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F ,in repair, PVC (SWR) junction, double 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified.

S&F in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M&L for machine cut cudappa stone slab 20-25 mm thick over cement screed base as in jambs and soffits of lintel laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing including 10mm thick rendering in CM 1:3 ,complete all as specified ans directed by Engineer-in-Charge.

Surface preparation of non structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer -in-charge (including removal of external plaster, wherever exists) COST inclusive of transportation, labour, conveying debris away from the out side of MD land, tools and tackles, lead and lift etc including necessery scaffolding ,form work etc, complete all as specified and as directed by Engr-in-Charge.

Removal of damaged structural concrete along with loose damaged and cracked concrete/ cover concrete at all specified locations up to beyond the corroged steel reinforcements to a depth of 10 mm minimum behind the reinforcement by chipping/ hacking with chisel and hammer or by mechinical means like chisel hammer, pneumatic chippers incl high pressure water jetting to chipped concrete and reinforcement and removal and disposal of debris within owners premises incl. all plants and machineries.,complete all as specified and as directed by Engineer-in-charge.

M&L for Cleaning as directed & specified all rust/scales/ corrosion from reinforcement bars using rust remover Reebaklens RR- Rust remover, cleaning and etching agent supplied in 1/2, 1 and 5 ltr containers, having specific gravity 1.16-1.22 @ 25 degree celcius, reebaklens RR cleaning agent is a combination of acid based materials, corrosion inhibitors and dispersing agents and is supplied as a clear green solution application of reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours followed by cleaning the surface with wire brush and washing surface with fresh water as required to exposed reinforcement bars complete as specfied.

M&L for Providing and applying inhibition coats/system to exposed reinforcement bars after drying & also mew bars after cleaning & removing scales and rust completely as specified. Nitozinc primer Two component epoxy zincrich primer supplied in 1 and 5 ltrs pack, two component system based on metallic zink and epoxy resin which on mixing gives a grey coloured liquid. An anti corrosive coat contents active 'Zinc-rich' system which combates corrosion by electro chemical means. having specific gravity of 1.75, adhesive bond strength > 1.5N/mm2 solid content 60%, 40 microns DFT, Fully dry/Rrcoatable-45 minutes to 1 hour. Typical application includes surface preparations by cleaning steel surface to a bright condition paying particuler attention to the back of exposed steel bars, mixed two components slow speed heavy duty drill fitted with a paddle, applying unbroken coat with suitable brush and alloy to dry, after 30 mins apply second coat to ensure complete cover to exposed steel/ reber etc complete. Total dry film thickness is 40 microns.

M&L for Cutting, fabrication new reinforcement FE-500 and fixing with old existing reinforcement which was reduced to 20 % or more of its original dia as provided in original structure and additional steels as directed by EIC to be fixed with chemical anchor grout lokfix E55- styrene free vinyl-ester resin based cartridge syatem for anchoring reinforcement supplied in 300 ML cartidge with a single mixture nozzle, application inclueds drilling hole close to old reinforcement bar with suitable drill as per dia of the bars, cleaning the hole with wire brush and compressed air, putting lokfix E55 with gun followed by placing rebar with slide rotational motion to avoid air void formation etc complete as directed by Engr-in-Charge.

Drilling holes in to existing concrete surface for anchoring of new rebars with 10 mm dia shear connectors at 0.5 mtr c/c and fixing with chemical anchor lokfix E55-styrene free vinylester resin based cartridge system for anchoring reinforcement supplied in 300 ml cartidge with a single mixture nozzle, shall be tested in accordance European approval to EAD-33087-00-0601 for use in post-installed rebar, which suspersedes ETAG 001 TR 023 (rebar), LEED compliant VOC Level, Fibre resistance < 120Mins, Seismic C1 testing as part of EAD 330499-00-0601 for specific fastening sizes etc. Typical application inclueds drilling holes 14mm dia and 90mm deep as per manufactures recommandation, cleaning the hole with wire brush and compressed air, putting lokfix E55 with gun followed by placing shear connector with slide rotational motion to avoid air void formation etc complete as directed by EIC.

M&L for Providing and applying Renderoc RG-Polymer modified micro-concrete supplied in 25 kg moisture resistant bag should possess following properties when mixed with clean water at w:p ratio 0.16, such as compressive strength (BS 4551-80)-50 Mpa at 28 Days, Tensile strength -2Mpa @ 28 days, flextural strength (BS 4551-80) Mpa at 28 days, Young's modulus-25 KN/mm2, Expansion characteristics (ASTM C827-1987) unrestrained expansion 1 to 4% pressure approx. 0.004 N/mm2, Thermal conductivity-1.5 W/m degree cel. fire rating (EN 1504 cl 5.5)-class A1, fresh wet density (mixed density @27 degree cel. ) -2100-2200 Kg/m3. Typical application inclued mixing whole bag with clean water about 4 litres mixing in suitable container with heavy duty slow speed mixture machine to produce uniform free flowing mix, pouring the same in to the form work using suitable arrangement or if required using pupping device for uniform flow of micro concrete. The side shuttering can be removed after 3 days and the bottom shuttering after 7 days ensuring proper bond between the micro concrete and existing concrete substrate. item rate ia inclusive of materials and labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by Engr-in-Charge.

M&L for Providing and applying bond coat on the prepared surface to receive polymer modified mortor/ polymer modified micro concrete , with two components epoxy based bonding coat Nitobound EP- Epoxy rasin concrete bonding agents supplied in 1/2, 1 and 4 ltr Packs, having specific gravity 1.15 to 1.2 gm/cc, Compressive strength (BS 6319 Pt 2)-50 Mpa at 7 Days, Tensile strength (BS 6319 Pt.7)-20Mpa @ 7 days, flextural strength (BS 6319 Pt.3) -35 Mpa at 7 days, Shear strength (BS-6319 Pt.4) 10 MPa at 7 Days having an over lay time of 6 hrs and 30 degree cel. high bond strength : bound strengthis more then the tensile strength of goood quality concrete barrier coat acts as a 'barrier coat to the migration of chloride inos from host concrete. Laying of reinstatement polymer modified mortor or micro concrete shall be completed within over lay time of bounding coat. The bond coat act as a bonding coat between old ad new concrete. Typical application includes cleaning all loose dust, dirt, grease from host concrete surface by suitable means, mixing both components of bond by heavy duty slow speed mixer until a unifrom consistency, apply unbroken coat of Nitobond EP with stiff brush covering complete area of patch repair before plcing mortor or nicro concrete. Item rate inclusive of materials all labour, tools and tackles, scaffolding and transportation etc.

M&L for Providing and laying Renderoc SP-40 shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortor supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt. 116) -> 20 MPa at 1 day & > 45 MPa at 28 days. Tensile strength (BS 63199 Pt7)>2.5 Mpa at 28 Days, Flexural strength (BS 6319 Pt.3)>7 Mpa at 28 Days, During Shrinkage to ASTM C157-93, 28 days<1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25 ltr to 4.5 ltr, mixed with suitable container with heavy duty slow speed mixer machine to achieve lump free mortor consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slab, piles etc, where tha thickness of application is less then 50 mm in patch as per specification after applying bounding coat item rate is inclusive of materials all labour tools and tackles, scaffloding and transportation etc. complete as per specification and as directed by Engr-in-Charge.

Taking down cement plaster or terrazzo from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L for Rendering/plastering, 15 mm thick in cement mortar (1:4) on brick or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified.

M&L for 15mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for 10mm thick rendering in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified.

M&L for preparation of newly plasterd surface of concrete or brick surfaces and applying Two coats ( having proportion @1.67 Litr/10 Sqm) of acrylic smooth exterior paint of required shade and including priming coat of exterior primer applied @ 2.20 Kg / 10 sqm, complete all as specified and as directed by Engr-in charge.

M&L for Preparation of newly plastered surfaces of walls & applying two coats of OBD on chalk whiting on plastered surfaces complete all as specified.

M&L for Preparation of newly plastered surfaces of Wall & applying two coats coats of white wash complete all as specified.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats coats of white wash complete all as specified.

M&L for Preparation of old decorated surfaces of wall and applying one coat of white lime wash (white washing) on walls including corneces, pillars complete all as specified and directed.

M&L for Preparation of old decorated surface of wall and applying one coat of oil emulsion distemper complete all as specified.

M&L for Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified.

M&L for complete removal of existing treatment on old surface of wall in any position washing down with water and cleaning the surface from all loose dirt, chalk, grease, fungal etc and finishing wall with two coat of weather proof acrylic paint over a coat of weather proof primer etc ,complete all as specified and as directed by Engr-in-Charge.

M&L for cleaning and preparation of old painted surface of wall apply one coats of weather proof paint camouflage pattern complete all as directed.

M&L for Preparation of old decorated surfaces on ceiling and applying one coat of white lime wash including cornice and pillars etc complete all as specified.

M&L for Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Preparation of old decorated surface of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Labour only of taking up or down steel tubing and connections of 20mm bore of pipe including cleaning and refixing in the same position as in wall/ roof /walls, etc during carrying out of water proofing treatment without damaging to existing services, etc. all as specified and directed

Labour only of taking up or down steel tubing and connections of 25 to 32mm bore of pipe including cleaning and refixing in the same position as in wall/ roof /walls, etc during carrying out of water proofing treatment without damaging to existing services, etc. all as specified and directed

Labour only for disconnecting existing over head tanks of capacity exc.500 and n.exc 1000 ltr, setting aside or lowering if required for repair of roof water proofing treatment and hoisting, reconnecting and re-fixing in position after necessary work without damaging to existing services etc. all as specified and directed.

Cutting holes into or through cement concrete slabs, RCC slab chajjas, etc. superficial Area Exc 500sq cm but n exc 0.1 sqm as specified and directed.

M&L for cement concrete Type C2 1:3:6 (40 mm graded aggregate) in foundations, columns, pillars, post holes filling and mass concrete including caps and bases as specified and directed.

S&F Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete (Fe-410W Gde-E 250 quality-A) all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 as specified and directed.

S&F Mild steel bolts (dia of neck exc. 11 & n.exc 15 mm and length exc 10cm and n.exe15cm long) purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut fixed completed all as specified and directed.

S&F Mild steel rolled sections as in framing for cladding, glazing, valley gutters and similar works and the like fixed with angle cleats and connecting plates, etc (Fe-410W Gde-E 250 quality-A) including distance pieces, cleats etc complete all as specified and directed.

S&F 0.80mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with MS flats or ms angles etc including making holes and fixing drain pipe where required complete all as specified and directed.

Cutting chases, pinning in, making good to facings on stone concrete block or slab walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for inserting/concealed roofing sheets etc. and making good cutting exceeding 20cm girth as specified and directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M&L for 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type, BWR grade fixed with screws to timber frame work complete all as specified.

M&L for 12 mm thick Particle board, medium density, flat pressed, single layer type or three layer type, BWR grade fixed with screws to timber frame work complete all as specified.

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, Exc 13 Sq cm & n Exc 25 Sq cm in 2nd class HW, Complete all as specified.

S&F for 75 mm brass handles, cast type , polished type complete all as specified and directed by Engr-in-Charge

M&L for 4 mm thick sheet glass n exc 0.5 sq.m in each pane fixing cabinet shutters with necessary screw/fittings complete all as specified and directed.

M&L for Stainless steel trolley made with perforated sheet of not less than 1.52 mm thick and SS edging wire and slided over SS telescopic renners which is fixed to wall/stone with suitable screws of desired shape and size as directed by Engr-in-charge

S&F Stainless steel soft close hydraulic action hinge with capacity to take load of 12 to 20 mm thick board all as per directed and specified.

S&F Magnetic catch brass body and striking plate with approved qulity complete all as specified and directed by Engr-in-Charge.

S&F heavy duty SS Zink plated Telescopic runners for SS trolleys having fully extended length min 500mm and 45.4 mm wide, loading capacity 45 kg/pair including concealed screws and bolts fixed to the wall or stone as directed by engr-in-charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil as specified and directed

M&L for PCC 1:4:8 (using 40 mmgraded stone agg) type D2 as in foundation and sub base etc complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry 1:3:6 Type C-1 (using 20mm graded aggregate)with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete complete all as specified and directed

M&L Hardcore of guage n.exc 63mm, deposited, spread and leveled in layers n exc 15cm thick, watered and rammed to a true surface in broken bricks all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in finishing surfaces of concrete, finish even and fair (without using extra cement), complete all as specified and directed.

M&L for preparation of newly plastered surfaces and applying three coats of white wash ,complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in soft / loose soil ,complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point where directed ,complete all as specified and directed.

M&L for Surface dressing n exc 15 cm deep and getting out hard/ dense soil complete all as specified.

M&L for Cement concrete type D2 1:4:8 ( using 40mm graded stone aggregate) in foundations, filling and mass-concrete complete all as specified.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified.

S & F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified.

S&F Tie bars with screwed ends, nuts, washers and mild steel paltes for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to Fe 410-0 or Fe 310-0 complete all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 Cum, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface. (soft/loose soil) complete all as specified.

S&F wall paper fixing at site on existing solid PVC wall paneling inclusive of solvent cement as per Manufacturer instruction/ specification complete all as specified.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out hard/ dence soil complete all as specified.

M&L for Half brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:6 complete all as specified.

Shree Gajanan Enterprises

Vinod Enterprises

Xcel Industries

M/s Qureshi Construction Co