SPECIAL REPAIR TO STORM DRAINS AT SAILORS AND CIVILIAN MARRIED ACCN AREA AND SPECIAL REPAIR TO BLDG NO P 250 AT CIVILIAN MARRIED ACCN AT INS SHIVAJI LONAVLA

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles and rubbish off the premises etc and removal of rubbish/ demolished materials out of MD land complete all as specified and directed by Engineer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed by Engineer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles.complete all as specified and directed by Engineer-in-Charge.

S&F Non Skid (coloured) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specifed and as directed by Engineer-in-Charge.

M&L for Glazed (Coloured) ceramic tiles in vertical surfaces 300 x 450 x 7 mm/ 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to matchetch including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles. complete all as specified and as directed by Engineer-in-Charge.

M&L for 20 to 25mm machine cut pre polished kota stone slab floor,or steps in single piece with round nosing with three numbers of serration as in treads of steps for staircase laid over cement screed bed and jointed with grey cement slurry mixed with pigment to match the shade of of the slab including rubbing and including over 15mm thick screed bed or bedding layer in CM1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L for 20 to 25mm machine cut pre polished kota stone slab as in riser of steps, skirting, window cills, dado and pillar laid over cement mortar backing coat jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles. complete all as specified and as directed by Engineer-in-Charge.

M&L for Machine cut green marble slab, 18-20mm thick, single piece in full length of window cill/jamb, cooking platforms over and including cement mortar backing coat, 10 mm thick in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge.

Rounding and moulding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs vitreous china water closet 'Orissa' pattern of size 580mm X 440mm, white with integral foot rest and 'P' or 'S' trap, including PVC flush pipe and provision of lime concrete bedding complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Low / high level flushing cistern 10 ltr capacity, PVC valveless, syphonic action incl waste pipe, pair of CI brackets and all accessories complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs vitreous china wash basin, white, flat back, size 580mm X 450mm including CI brackets, 32mm dia brass chromium plated waste fittings with long screwed shanks and fly nuts flanged end bedded in red lead cement and other end fixed with & including cutting for & pinning in end of brackets and 15mm bore pillar tap, cast copper alloy fancy type chromium plated, screwed down high pressure complete all as specified and as directed by Engineer-in-Charge.

S/F low density polyethene pipes (LDPE) 40mm of pressure rating 6 Kg/cm2 fixedcomplete to walls, ceiling or laid in floors etc, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated shower rose with or without swivel joints 75mm size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Bib taps, fancy type, chromium plated with crutch sc-rewed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Pillar taps, fancy type, chromium plated, screwed down, high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Stop valves 15mm bore , cast copper alloy, fancy type chromium plated, screwed down, high pre-ssure, with crutch , screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Angle cock, cast copper alloy, fancy type chromium plated, screwed down, high pre-ssure, with crutch screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repair PVC connections, 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Tubular towel rail, 20mm dia, 60cm long between flanges fixed with and including Chromium plated brass screws and wooden/plastic cleats . complete all as specified and as directed by Engineer-in-Charge.

Demolition of Concrete of any description and in any position if cement concrete is reinforced (reinforcement cut as required to facilitate demolition) not otherwise specifically provided for removing all rubbish/debris outside MoD land as per instruction complete all as specified and directed by Engineer-in-Charge.

M&L for PCC lean concrete 1:2:4 type B2 laid in layers of complete all as specified and directed by Engineer-in-Charge.

S&F in repairs water storage tanks of 1000 ltrs capacity rotational moulded (Triple layered cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 25 mm bore including cleaning for re-fixing or removal to store

Cutting chases, pinning in walls. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing, cutting not exc 10 cm girth etc complete all as specified and directed by Engineer-in-Charge.

S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all fittings such as Tee, bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts/with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and as directed by Engineer-in-Charge.

S&F Tubes, ‘medium grade’ galvanised, 25 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but not exc 20 cm girt complete all as specified and as directed by Engineer-in-Charge.

S&F in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20 mm bore complete all as specified and directed by Engineer-in-Charge.

Taking down steel/aluminium windows/ventilator of any size with all fittings complete.

M&L for powder coated aluminium three track, three shutter (of equal width) sliding type window without sash bar including necessary jointing clip, rubber packing, neoprene rubber gasket, locking arrangement (star lock) bearing (two no's for each sliding shutter ) &4 mm thick plain glass for glazing with for two shutters and aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire stapless complete all as specified and directed for one shutter & including following powder coated section as given in 'JINDAL' catalouge complete all as specified and as directed by Engineer-in-Charge.

S&F aluminium ventilator louvered type without sash bar section as per designation 63400 of IS 737 ( minium 15 micron anodised) including necessary jointing clip, rubber packing,including necessary locking arrangement , anodised snap beading screws and 4mm thick pin headed glass etc complete

Taking down chowkat or frame with shutter (without taking off shutter from the frames), n. exc 1.50 sqm each complete as directed by Engineer-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 75*50 mm comprising of virgin PVC polymer and non toxic additives PVC solvent cement and screwed with full body threaded star headed SS screws of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory Made 24mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Flush Door Shutter of required size comprising of virgin PVC and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) having good screw holding capacity Minimum Compissive of 50 N/mm2, of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant.

Taking down chowkat or frame with shutter (without taking off shutter from the frames), exc 1.50 sqm but not exc 4.0 sqm each complete as directed by Engineer-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid Double door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125*65 mm comprising of virgin PVC polymer fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory Made 30mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Flush Door Shutter of required size comprising of virgin PVC and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) having good screw holding capacity Minimum Compissive of 50 N/mm2, of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant.

S&F Providing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge

Supply and fix aluminium alloy anodised Aldrop sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolt of extruded section of size 300 mm fixed at any position all as specified and directed.

S/F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S/F 150mm length Extruded aluminium alloy handles, fabricated type, anodised.

S&F 200mm length Aluminium anodised, barrel tower bolts of ex truded section and fixed

Dismantling / taking down PVC/ Cast iron soil /waste pipes 100 mm / 75mm bore including all fitting like bends and fittings etc

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc complete all as specifed and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc complete all as specifed and directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed by Engineer-in-Charge.

S&F 75 bore PVC (SWR) branch piece, single (single T ) equal or unequal with access doors etc, complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) junction PVC (SWR) branch piece,double (double Y) equal or unequal with access doors etc, complete all as specified and as directed by Engineer-in-Charge.

M/L for Rendering 10mm thick in CM 1:6 on brick work or concrete surfaces finished even and smooth (without using extra cement) including taking down and removing debris outside MD land etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including two coat of white cement based wall care putty complete all as specified and as directed by Engineer-in-Charge.

M/L for rendering 15 mm thick in CM 1:4 on brick walls or concrete surfaces to be finished even and smooth (without using extra cement) etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new external surface of wall applying two coats of exterior grade weather resistant, antifungal acrylic latex paint over one coat of acrylic primer on walls, chajjah after filling of cracks using crack filler complete all as specified and as directed by Engineer-in-charge.

M & L for rendering 5 mm thick in CM 1:3 on concrete surfaces as in ceiling and finishing the surface even and smooth including taking down and removing debris outside MD land etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces on ceiling and applying three coat of white wash etc complete all as specified and directed by Engineer-in-Charge

M&L for Preparation of old plastered surfaces of walls,Pillars, cornices etc by brooming down with steel wire brush, scraping down smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on the walls, pillars, cornices etc complete all as specified and as directed by Engineer-in-Charge.

All as per Item above but here-in-before on ceiling.

M&L for complete removal of existing treatment of wall and applying two coat of oil bound distemper, over a coat of primer, over two coat of wall care putty, complete all as specified and as directed by Engineer-in-Charge.

M&L for complete removal of external surface of wall and applying two coats of exterior grade weather resistant, antifungal acrylic paint over a coat of alkali resistant primer on walls, chajjah etc. complete all as specified and as directed by Engineer-in-Charge.

Completely removing existing water proofing treatment of any descriptions and any type including demolition of padding and top layer of plaster and chhajja surfaces and scrubbing the surface with wire brush and cleaning wash down with water and removing the waste material / debris out of MoD land complete all as specified and directed by Engineer-in-Charge.

M/L for rendering 10 mm thick in cm 1:4 using plaster on external surface of brick walls or concrete roof surfaces mixed with Integral waterproofing compound all as per manufacturer instructions etc, finishing the surface even and smooth without using extra cement etc, complete all as specified and directed by Engineer-in-Charge. Note : Water proofing compound will be measured and paid separately.

M&L for PCC lean concrete 1:2:4 type B1 (20 mm graded aggregate) aggregate) laid in layers of complete all as specified and directed by Engineer-in-Charge.

Supply only Integral waterproofing compound.

M&L for water proofing treatment to RCC roof slab and windows chajja all as specified below and as directed:- (a) Apply one coat of bituminous primer @ 0.25 Kg/Sqm. (b) Apply a coat of blown type bitumen grade 85/25 heated to working temperature of 180 degree centigrade and applied at 1.20 Kg/Sqm of the surface area. (c) Laying APP polymer modified membrane 3mm thick with non woven polyster reniforcement weighing not less than 3.00 Kg/Sqm applied by torch application method. (d) Apply a coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm.

S&F in repair for tubular curtain rod 20mm dia of Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed by Engineer-in-Charge.

M&L for complete removal of existing treatment of steel surfaces, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of anti corrosive paint over a coat of anti corrosive epoxy primer complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and labour for repairing of RCC projection, chajjas, facia, bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any sitution / floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of weight 3 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of weather proof emulsion paint to match with existing surfaces complete all as specified and directed by Engineer-in-Charge. Note:-Unit rate of this item includes the cost of scaffolding,formwork etc. and nothing extra shall be paid on account of variation in height.

Removing Silt from drain,culvert etc. and brooming down with steel wire brush, scraping down smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots etc complete all as specified and as directed by Engineer-in-Charge.

Cutting or uprooting grass on old mud phuska, removing rubbish off the premises, cleaning surface of dranage area complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick/stone masonry built in cement mortar incl coping etc complete in any position, locations etc incl removing the unserviceable debris as specified and as directedby Engineer-in-Charge.

Demolition of cement concrete in any position and paving n exc 15cm thick (below or above ground level) any position and removing the rubbish outside MoD land complete all as specified and directed by Engineer-in-Charge.

M & L for cement concrete type C2, 1:3:6, (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed by Engineer-in-Charge.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

Walling of random rubble uncoarsed, well bonded, bedded and solidly hearted, built in CM 1:6 using rubble obtain from demolition.

Extra over Granite or trap stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 20mm to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses.

M&L for Pre-cast cement concrete block masonry in Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and built in CM 1:6 complete all as specifed and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer-in-Charge.

M&L Providing, cement concrete of 1:2:4 B1 (20mm graded aggregate) as in copings, bottom of drain etc complete all as specifed and directed by Engineer-in-Charge.

M&L for providing reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone agg) as in cover slabs. complete all as directed by Engineer-in-Charge.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

M & L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Extra for forming Fair finished drain of channel upto 45cm inner girth in cement concrete, using extra cement including forms, moulds, miitred/stopped ends etc Note: Sl Item Nos 1 to 88 is required to be carried out at height upto 15 m above GL in narrow spaces/widths.rate is deemed to be included for all necessary scaffolding, protective measures required to carried out work any above mentioned heights

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-Charge .

M & L for Point wiring with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box fixed with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed by Engineer-in-Charge. (a) One light point or one fan point or exhaust fan or bell point controlled by one switch

One 3 pin socket outlet, 5 Amp independent

One 3 pin socket outlet, 5 Amp on the same board with other switches

All as per item No.2 here in before but wiring with cables of size 2.5 sqmm for wiring & cables of size 2.5 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 3 pin Switch/Socket outlet on Independent board complete all as specified and directed. (Note : cutting chases & making good of disturbed surfaces shall be measured and paid separately).

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed by Engineer-in-Charge.

S & F socket out let, 2 in 1, 3 pin, 5 Amps, 240 volts complete all as specified and directed by Engineer-in-Charge.

S & F Switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts complete all as specified and directed by Engineer-in-Charge.

S & F Switch socket combination, 5 in 1, 5/15 Amps, 240 volts, flush type complete all as specified and directed by Engineer-in-Charge.

S & F Ceiling rose, 3 way PVC insulated body complete all as specified and directed by Engineer-in-Charge.

S&F Buzzer, Ding Dong AC, 230 Volts single pole.

S&F electronics type fan regulator ,120 W complete all as specified and as directed. Make: MK/Anchor (Roma)/ABB

Supply and fixing Batten 1x18W(single side supply)for LED TUBE LIGHT pre -coated CRCAA sheett, end caps made up with engineering plastic all as specified and directed by Engineer-in-Charge. Make : Bajaj (BLRB - DB 118) or equivlent PhilipsHavells.

Supply and fixing ROD 1x18W (single side supply)for LED TUBE LIGHT T8 tube with polycarbonate body all as specified and directed by Engineer-in-Charge. Make : Bajaj (BLRB - 20W LED) or equivlent PhilipsHavells.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make: Crompton or equivlent Bajaj/Philips/Havells

S/F switch bell push, flush type 5 Amp.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fixing LED Building light/street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.Make: Crompton or equivlent Bajaj/Philips/Havells

M&L for earthing complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized iron strip 25 X 4 mm by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

S&F MCB DB TPN 4 ways double door with 440 Volt, 100 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed by Engineer-in-Charge Make:Havells QVE series or equivlent legerend/standard/indoasian

S&F MCB DB SPN 4 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed by Engineer-in-Charge Make:Havells QVE series or equivlent legerend/standard/indoasian

S&F in repairs MCB SP 5 To 32 AMP, single pole 240 Volts 10KA ''C''&''B'' curve , as per site requirment,Complete all as specified and directed by Engineer-in-Charge.

S&F in repairs MCB SPN 6-32 AMP, 240 Volts 10KA 'C' curve , Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB TPN/FP 40 To 100 AMP 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning.

Taking down of Old MCB DB / control box any type any size including MCBs and separating the serviceable MCB DBs and MCBs for reuse at site

M&L for sub main wiring drawing through PVC casing and capping with Wiring alongwith earth wire size 2x4.0 sq. mm +1 x4 sq. mm earth wire earth wire of FRLS is PVC insulated copper conductor, single core cable in surface/recessed as required .Note:-Two run of 4 sqmm wire and One run of 4 sqmm wire and One run of PVC casing caping will be measured as one running meter.

Taking down electric meter of any type and any make single/three phase by dismantling of all electrical connection checked the meter, and Refixed same Nos of meter on wooden board in metal box of suitable size in same Nos of quarter after repair works completed.

Supply lay and testing cable XLPE insulated screened beded,galvanized steel trip or wire armoured, electric power cables (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 35 sq mm 3.5 core. Including taking down old unserviceable cable any size by dismantling of all electrical connection etc all as directed by Engineer-in-Charge.

Excavation in trenches n. exc. 1.5 M in width and 1.5 M in deep for laying of pipes and getting out in Soft / loose Soil complete as specified & directed by Engineer-in-Charge

Returning, filling including spreading, leveling, watering and well ramming in layers not exc 25cm in soft/soil complete all as specified and directed by Engineer-in-Charge

Removing excavated material n. exc. 50 M away and depositing where directed at a level n. exc. 1.5 M above the starting point complete all as specified and as directed by Engineer-in-Charge.

M&L Sand cushioning for UG cable protection/ducts, consolidated sand compacted with clean dry sand all as directed and specified by Engineer-in-Charge.

Supplying and laying factory cast un-reinforced precast concrete cable cover, embossed the mark " LT CABLE" class LV, type 1 with peak, size 250mm x 150mm x 40m laid in trenches as specified and as directed by Engineer-in-Charge .

Supply & fix exhaust fans steel body AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and directed by Engineer-in-Charge. Note:- Cost of making hole for Exhaust fan of required size at site is deemed to be included in quoted rates.SKU Code-70003 Bajaj/Havells

VIJAYA ENTERPRISES (BID ID -3385130)

Durga Enterprises (BID ID -3376566)

JADHAV CONSTRUCTION AND INFRASTRUCTURE (BID ID -3373495)

M/s S.D Construction Co (BID ID -3377491)

United Engineers and Contractors (BID ID -3377270)