Repair/renovation of Swimmi...

Amount

HSR item 1 to 117:- [10.1]Providing and laying of base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling.

[10.100.2]Cement Concrete 1:8:16 Flooring 2. Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth.

[10.50.1]Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 1. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

[10.63.2]Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2. Size of Tile 600x600 mm

[11.21]12 mm cement plaster 1:2 (1 cement : 2 stone dust).

[11.25.1]Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): 1. Flush / Ruled/ Struck or weathered pointing

[11.26.1]Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand): 1. Flush/ Ruled/ Struck or weathered pointing

[11.32.1]Rough cast plaster up to 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. 1. Ordinary cement finish using ordinary cement

[11.5.3]12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand)

[11.58]Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete

[11.6.1]15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand)

[11.64.1]Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. New work (two or more coats) over and including water thinnable priming coat with cement primer

[11.65.1]Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer`s specification. 1. Two or more coats on new work

[11.67.1]Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 1. Water thinnable cement primer

[11.8.2]12 mm cement plaster of mix : 2. 1:6 (1 cement: 6 coarse sand)

[11.95.1]Finishing walls with Acrylic Smooth exterior paint of required shade : 1. New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

[13.27]Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

[13.41]Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

[20.20.2.1]Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading 2.1. Including cost of specials 15 mm internal diametre of pipeline

[20.20.2.3]Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading 2.3. Including cost of specials 25 mm internal diametre of pipeline

[20.21.6]Labour for laying jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and special tees, bends, sockets, elbows etc. in trenches in the ground cutting, threading and testing, etc. complete 6. 50 mm internal diameter

[20.21.9]Labour for laying jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and special tees, bends, sockets, elbows etc. in trenches in the ground cutting, threading and testing, etc. complete 9. 100 mm internal diameter

[20.23.1]Extra for fixing and jointing union couplings in G.I. and W.I. pipelines. 1. 15 mm internal diameter

[20.23.2]Extra for fixing and jointing union couplings in G.I. and W.I. pipelines. 2. 20 mm internal diameter

[20.23.3]Extra for fixing and jointing union couplings in G.I. and W.I. pipelines. 3. 25 mm internal diameter

[20.23.6]Extra for fixing and jointing union couplings in G.I. and W.I. pipelines. 6. 50 mm internal diameter

[20.26.1]Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 1. 11.43 cm thick wall

[20.26.2]Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 2. 22.86 cm thick wall

[20.26.3]Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 3. 34.29 cm thick wall

[20.28.1]Cutting holes up to 23 cm square for pipes in floor and roofs of cement concrete reinforced concrete or reinforced brick work and making good including, repointing, replastering, replacing bitumen and colour or white washing where required. 1. 75 mm thickness of roof or floor

[20.31.1]Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 1. 15 mm internal diametre

[20.31.3]Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 3. 25 mm internal diametre

[20.31.4]Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 4. 32 mm internal diametre

[20.31.5]Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 5. 40 mm internal diametre

[20.31.6]Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 6. 50 mm internal diametre

[20.36]Making connection with the existing G.I. branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site.

[20.38]Fixing peet value and stop cock surface boxes (coat iron) including cartage from divisional stores or nearest railway station to site of works.

[20.63.2]`Providing, lowering, laying in trenches, aligning, fixing in position and jointing Ductile Iron (DI) ISI marked K-9 grade SandS pipes as per 15:8329-2000 (amended up to date), with internal cement mortar lining for potable water with rubber ring (EPDM/SBR) joints as per IS: 5382-1985 (excluding special accessories) complete including all material, labour, hydraulic testing and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/W to be measured and paid separately. ` 2. 150 mm i/d

[21.27.1]Fixing 560mm, 500mm and 450mm internal diameter circular or 455mm x 610mm clear inside opening rectangular cast iron manhole cover and frame including carriage from the stores of the engineer-in-charge to site of work loading, unloading including stacking and setting the same to correct lines and levels in 1:2 cement sand mortar over manhole etc. 1. Heavy duty Circular 560 mm or 500 mm i/d (weight as per I.S.I.)

[21.28]Providing and fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS :1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1:2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge

[21.84.3]Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2:4 slab 100 mm thick/cement concrete topping, 50mm thick with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. 3. Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab)

[21.85.3]Extra for every 0.30 metre depth of Inspection chamber 3. 600 mm x 900 mm inside

[21.94.1]Providing salt glazed stone ware pipes grade ‘A’ in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 including the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 1. 100mm i/d

[21.94.2]Providing salt glazed stone ware pipes grade ‘A’ in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 including the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 2. 150mm i/d

[22.1.5]Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 5. White vitreous chinaware Angle back wash basin size 600 x 480 mm with single 15mm C.P. brass pillar tap

[22.103.3]Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 3. 25 mm nominal bore

[22.104.1]Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 1. 15 mm nominal bore

[22.106.1]Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 1. 15 mm nominal bore

[22.107.1]Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1. 15 mm nominal bore

[22.108.1]Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1. 15mm nominal bore

[22.109]Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

[22.127]Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

[22.14.2.1]Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 2.1. Flexible pipe 32 mm dia

[22.15]Providing and fixing CP Brass 32mm size Bottle Trap of approved quality and make and as per the direction of Engineer-in-charge.

[22.181]Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

[22.209]Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

[22.212.1.2]Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P. brass screws and rawl plugs etc. complete including cutting and making good the walls etc. 1.2. C.P Brass Two Way

[22.22.1]Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 1. White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

[22.222.2.2]Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.2. Single Socket Type B 110mm o/d SWR UPVC pipe lines laid complete

[22.26.2]Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 2. Single half stall urinal with manually operated5 litre P.V.C. flushing cistern and manually operated stop cock/ angle valve

[22.33]Providing and fixing white vitreous chinaware extended wall mounting water closet of size 780x370x690 mm of approved shape including providing and fixing white vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

[22.42.1]Providing and fixing toilet paper holder : 1. C.P. brass

[22.46]Providing and fixing white vitreous chinaware battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre and post flushing with water (250 ml and 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

[22.50.1.2.1]Providing and fixing partitions for different type of urinals. 1.2.1. Vitreous Chinaware Partition plate. Large size 835mm x 355 mm White

[22.81.2]Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 2. 75 mm dia

[22.86.2]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 2. 20 mm nominal outer dia Pipes

[22.86.3]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 3. 25 mm nominal outer dia Pipes

[22.86.4]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 4. 32 mm nominal outer dia Pipes

[22.87.6]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings This includes jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge. External work 6. 50 mm nominal outer dia Pipes

[22.98.6]Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 6. 65 mm nominal bore

[23.1.6.1]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.1. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm)

[23.1.6.3]COPPER WIRING IN MS CONDUIT (SURFACE/RECESS) 6.3. Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. 1 run of Size 4 Sqmm(1/2.24mm)

[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA

[23.22.5.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.3. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Double POLE

[23.4.1.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 1.1. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group A

[23.4.4.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 4.1. Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group A

[23.4.5.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 5.1. Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group A

[23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia.

[24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material.

[24.1.3]EARTHING AND LIGHTENING ARRESTOR 3. Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required.

[24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required.

[24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode.

[24.1.7]EARTHING AND LIGHTENING ARRESTOR 7. Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required.

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material.

[24.1.9]EARTHING AND LIGHTENING ARRESTOR 9. Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required.

[30.21]Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

[30.9]Regarding terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge.

[31.14.2]Rebarring work with 10ml inject able mortar epoxy adhesive (Hybrid Urethane Methacrylate adhesive) or chemical compound of make as approved by Engineer-in-Charge complete in all respect including drilling and cost of all materials 0 0 0 2. 10 mm dia (hole size 14 mm.& hole depth up to 100 mm) 0 0

[31.14.3]Rebarring work with 10ml inject able mortar epoxy adhesive (Hybrid Urethane Methacrylate adhesive) or chemical compound of make as approved by Engineer-in-Charge complete in all respect including drilling and cost of all materials 0 0 0 3. 12mm dia (hole size 16mm.& hole depth up to 120 mm) 0 0

[31.14.4]Rebarring work with 10ml inject able mortar epoxy adhesive (Hybrid Urethane Methacrylate adhesive) or chemical compound of make as approved by Engineer-in-Charge complete in all respect including drilling and cost of all materials 0 0 0 4. 16mm dia (hole size 20 mm dia & depth up to 200mm) 0 0

[31.14.5]Rebarring work with 10ml inject able mortar epoxy adhesive (Hybrid Urethane Methacrylate adhesive) or chemical compound of make as approved by Engineer-in-Charge complete in all respect including drilling and cost of all materials 0 0 0 5. 20mm dia (hole size 24 mm dia & depth up to 240mm) 0 0

[31.3.1]Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. 1. Bars up to 12 mm diameter

[31.3.2]Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. 2. Bars above 12 mm diameter

[31.4.2]Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. 2. Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make

[4.12.1]Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. 1. All kinds of soil

[4.16.1.1]Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 1.1. All kinds of soil Pipes, cables etc, not exceeding 80 mm dia.

[4.16.1.2]Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 1.2. Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

[5.25]Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

[5.42]Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge.

[5.43.1]Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 1. For thickness of tiles 10 mm to 25 mm

[5.45]Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

[5.7.4]Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 4. In cement mortar

[5.70]Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

[6.1.2]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 2. 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

[6.1.7]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 7. 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size)

[6.14.1]Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

[6.15.1]Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

[6.16]Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

[6.30.2]Centering and shuttering including strutting, propping etc. and removal of form for 2. Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

[6.30.3]Centering and shuttering including strutting, propping etc. and removal of form for 3. Suspended floors, roofs, landings, balconies and access platform

[6.33.6]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level 6. Thermo-Mechanically Treated bars of grade Fe-500D or more.

[6.34.6]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level. 6. Thermo-Mechanically Treated bars of grade Fe-500D or more.

[7.21.2]Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: 2. Cement mortar 1:6 (1 cement : 6 coarse sand)

[7.22.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand)

[7.22.2]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 2. Cement mortar 1:6 (1 cement : 6 coarse sand)

[7.28.2]Half brick masonry with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level. 2. Cement mortar 1:4 (1 cement :4 coarse sand)

NS items 118 to 200:- Earth filling under floors with dune sand (tiba sand)/earth, brought from outside (any lead), in 15 cm layer including laying, dressing, watering ramming, consolidating, excavation, carriage, loading, unloading and compensation etc. complete (based on HSR 2021)

Supply installation testing and commissioning of wall free mounting dust and vermin proof compartmentalized cubical panel made out of 2 mm thick CRCA sheet, required hardware 3 mm thick backlite sheet provided all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 caot of zine/Red oxide primer followed by 2 coats of powder coating in grey or required shade after rising, the panel having PU/Neoprene rubber gasket of not less than 3 mm thickness separate dectachable gland plate MS base channel hinged door with inter locking arrangement fo equipment/switch wear as per details.

Supply and fixing of copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing go same in existing panel including bending, cutting in required shape and size insulation with colour coding heat srinkable PVC insulation complete in all respect.

S/E LED flood light fitting 240 watt with IP 66 Multiple LED with lens optics, non- integral LED driver and pressure die-cast aluminium housing for effective thermal management. Total system lumen of ) 240 watt LED should be 25200 or above in cool day light (5700K), Lumen efficacy ) 140 lm/W, Power factor = 0.95, Average life =50000 hours, complete with all accessories as required with connections. Make Havells , Bajaj , Philips.

Providing and fixing Glass mosaic tiles on finished plain wall/floor surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall/floor surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same with Epoxy of desired shade. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge: NS (Make: Orient bell, Nitco, Ultra tile, Pavcon)

S/I/T/C of wiring and conduiting 2.5sqmm 2 core copper flexible wire including 25mm PVC conduit fitting all around swimming pool and pump room and all petty material required to complete the job In all respect. Make Polycab / Finolex / Havells / KEI (

S/I/T/C of wiring and conduiting 2.5sqmm 1 core copper flexible wire including 25mm PVC conduit fitting all around swimming pool and pump room and all petty material required to complete the job In all respect. Make Polycab / Finolex / Havells / KEI

Providing and fixing Glass mosaic tiles on finished plain wall/floor surface of size 48 mm x 48 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall/floor surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same with Epoxy of desired shade. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge: NS (Make: Orient bell, Nitco, Ultra tile, Pavcon):

S/I/T/C of wiring and conduiting 10sqmm 3 core copper flexible wire including 32mm PVC conduit fitting all around swimming pool and pump room and all petty material required to complete the job In all respect. Make Polycab / Finolex / Havells / KEI

Supply, installation, testing and commissioning of Surface / Ceiling mounting swimming pool LED under water light IP-68 , SS304 20W/12Volt including ABS Deck Box suitable for use with light , SMPS Supply or control transformer for 12 Volt Supply and 2 core 4Sqmm cable from light to pannel, consider pannel location more than 20 meter from pool center, Cable enclosed in PVC / UPVC plumbing pipes and fittings not less than 6kg/sqcm pressure from light to pannel , core cutting , digging of trench for cable as per site requirements , Light warranty 3yr. Make- Halbert / Astral / Watronix as directed byEngineer-in-charge including all Labour and Materials etc complete. LED COLOR: warm/cool white/RGB/blue

Supply and erection of 2 core 4 sqmm copper flexible cable paid extra length from 20 mtr used for under water light from panel to light complete with all petty material required to complete the job in all respect. Make Havells,finolex,polycab,kei etc.

Supplying, Installation, Testing and Commissioning of Filter for Main Pool (1200 MM Dia) Blue colour bobbin wound sand filters, manufactured totally in NON-CORROSIVE material and UV resistance surface. Filter should be supplied complete with manual air bleeder, water drain, emptying plug, fitted with collector arms and diffuser made from unplasticized PVC and polypropelene and with top mounted multi-port valve of 2` for carrying out filtration, back washing and rinsing of filter media. MPV should be supplied with pressure gauge. Flow Rate = 30 M3/Hr, Filtration Velocity = 30 M3/Hr/M2, Maximum Working Pressure 2.5 Kg/Cm2, Diameter = 1200 MM (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Supplying and filling of Multi Graded Sand for Filter (Each Pack Contains 50 Kg) Grade of Sand Media 4x8, 8X16, 16X32 Make: Pentair, Halbert, Astral, Hayward.

Providing and laying matt finished vitrified tile of size 600 mm x 600 mm x16 mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) in all shapes and patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer in-Charge. (Make: Orient bell, Somany, Kajaria, Nitco)

Supplying, Installation, Testing and Commissioning of Re-circulating Pump Self Priming pumps. Motorshafts in stainless steel AISI-420, impeller in polyroilen, mechanical seal in graphite.with motor -2850 rpm, 2.2 kw, 220 V or 380 V, 3.0 HP, protection IP-55 and insulation class-F. With Pre Filter 3 Phase, Flow Rate 22 M3/Hr @Head Size 10 Mtr (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Supplying, Installation, Testing and Commissioning of Square Main Drains(To Drain Out the Pool) ABS Drain Grills - 300mm x 300mm (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Collection of Ist class bricks tiles, at the site of work including carriage, loading unloading and stacking etc.

Providing and fixing fittings/accessories of Ozone make as given below. (i) SS Rod end knob (OSKH- 3STD-SSS), complete in all respect.

Supplying, Installation, Testing and Commissioning of Over Flow Channel Cover Grating (Material use ABS 300 X 24 MM) White/sky blue/blue or as approved by the Engineer-In-charge. (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Providing and fixing 12mm thick frosted toughened glass (AIS, Modi Guard or Saint Gobion make) duly toughened by standardized plant, with required holes and cut outs as fixed panels at all height for door/partition/glazing, fixed in position, complete in all respect as directed by Engineer-in-charge.

`Providing and fixing Stainless steel ladder of SS-304 Grade in 48 mm Dia x 3 mm thickness piping with 600 mm length – orange coloured or any approved one with fibre moulded steps, removable type, designed Stainless steel pool ladder with SS304 hand grip piping of 48mm x 3 mm thk, having 600 mm length x150 mm width x 70 mm thick – Anti skid-Button model – Non sharp-edged, concealed box type – Strong in 3.5 Kgs Weight , quality - Fibre moulded ladder steps in orange colour and ½” stainless steel 304 stud on through out with Dhoom nuts on both the ends. 2 Nos each - Fibre moulded foundation anchor cup with cover for top grouting and wall resting rubber bushes on bottom. - complete. Ladder having 3 steps. (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Providing and fixing fittings/accessories of Ozone make as given below. (i) Wall to Glass Connector 90 degree (OGC-4 STD PSS) suitable for 12 mm thick glass, complete in all respect.

`Providing and fixing Stainless steel ladder of SS-304 Grade in 48 mm Dia x 3 mm thickness piping with 600 mm length – orange coloured or any approved one with fibre moulded steps, removable type, designed Stainless steel pool ladder with SS304 hand grip piping of 48mm x 3 mm thk, having 600 mm length x150 mm width x 70 mm thick – Anti skid-Button model – Non sharp-edged, concealed box type – Strong in 3.5 Kgs Weight , quality - Fibre moulded ladder steps in orange colour and ½” stainless steel 304 stud on through out with Dhoom nuts on both the ends. 2 Nos each - Fibre moulded foundation anchor cup with cover for top grouting and wall resting rubber bushes on bottom. - complete. Ladder having 4 steps. (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Providing and fixing fittings/accessories of Ozone make as given below. (i) Glass to Glass Hinge 90 degree for 8-10 mm Glass (OSH-4 STD CP), complete in all respect.

Supplying, Installation, Testing and Commissioning of salt chlorinator with time clock, salt level (mins) 4000 ppm, cell output 45 gram/hr, 240 v and 50 Hz, IPX4, weight 9.8 Kg. (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward,Emaux.

Providing and fixing fittings/accessories of Ozone make as given below. (i) H type Door Handle (OGH-55S 32mm x 457 mm), complete in all respect.

Supplying, Installation, Testing and Commissioning of 240 Watt UV Clarifier flow rate 40,000 liters/Hr, Bulb Life Approx 10000 (Hours) with Electronic Ballast, Inlet-Outlet Socket, with Electrical Rating 240V and 50Hz. Dimension 980 X 110 X 270 mm (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Providing and fixing fittings/accessories of Ozone make as given below. (i) 180 Magnetic Seal (OPS-10 mm-STD), complete in all respect.

Supplying, Installation, Testing and Commissioning of 1.5` (38mm) Floating Hose Spiralwound 2 color - 12metre Graphite, EVA, UV Resistant, Designs to hose to keep floating even full of water and allows the cleaner to work freely of the pool floor including End Fittings. (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

Providing and fixing fittings/accessories of Ozone make as given below. (i) SS Rod to wall fitting knob connector (OSKH- 1STD-SSS), complete in all respect.

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 10Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing , chased in wall as per standard design (For water supply , drain , vaccume and overflow pipe). Make:-Supreme/Finolex 63 mm dia

Providing and fixing fittings/accessories of Ozone make as given below. (i) SS Rod to glass connector (OSKH- 2 STD-SSS), complete in all respect.

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 10Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing , chased in wall as per standard design (For water supply , drain , vaccume and overflow pipe). Make:-Supreme/Finolex 75 mm dia

Providing and fixing fittings/accessories of Ozone make as given below. (i) Foot rest (OZRSP -180 x 50- B), complete in all respect.

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 10Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing , chased in wall as per standard design (For water supply , drain , vaccume and overflow pipe). Make:-Supreme/Finolex 90 mm dia

Providing and fixing fittings/accessories of Ozone make as given below. (i) SS Rod (OSKH- ACC-19 2 mtr. SSS), complete in all respect.

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 10Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing , chased in wall as per standard design (For water supply , drain , vaccume and overflow pipe). Make:-Supreme/Finolex 110 mm dia

Providing and fixing Latch Lock, (to be fixed on glass shutters), complete in all respect as directed by the Engineer-in-Charge.

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 10Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing , chased in wall as per standard design (For water supply , drain , vaccume and overflow pipe). Make:-Supreme/Finolex 160 mm dia

Providing and fixing of Butterfly Valve With Complete Fittings Nut, Bolt, Flanges etc. complete Make : Zoloto / Sant/Bajaj 65 mm Dia

Providing and fixing of Butterfly Valve With Complete Fittings Nut, Bolt, Flanges etc. complete Make : Zoloto / Sant/Bajaj 100 mm Dia

Providing and fixing of Butterfly Valve With Complete Fittings Nut, Bolt, Flanges etc. complete Make : Zoloto / Sant/Bajaj 160 mm Dia

Providing and fixing Non return valve With Complete Fittings Nut, Bolt, Flanges etc. complete Make : Zoloto / Sant/Bajaj 65 mm Dia

Providing and fixing Non return valve With Complete Fittings Nut, Bolt, Flanges etc. complete Make : Zoloto / Sant/Bajaj 100 mm Dia

Providing and fixing Non return valve With Complete Fittings Nut, Bolt, Flanges etc. complete Make : Zoloto / Sant/Bajaj 160 mm Dia

Supplying, Installation and Testing of Electrical Control Panel (Complete in all respect likewise: switch gears, MCB, TPN, Bar Channels, PVC Glands, Voltameter, Ameter,Buttons) for 3 Nos. Pump Make: LandT/Scheinder/ABB

Providing and fixing pillar tap expose part kit single liver, complete in all respect. Make:- Jaquar, AREP

Supply of Suction Sweeper Maintenance Machine as detailed below along with allied items:- 1. 2 HP pump single phase- 1 No. 2. SS Troley wheel type (Fabricated) - 1 No. 3. Starter on/off Switch - 1 No. 4. Electrical wire two core-35 mtr with complete maintenance kit. 5. Flexible vaccum hose pipe 15 mtr 40 mm/ Blow moulded PE vaccum hose 1.5`` x 50 mm - 2 Nos. 6. Telescope pole 4.8 mtr/ Ribbed Pole 4.8 mtr-1 No. 7. 18`` stainless steel vaccum head with 4 wheels Alu body (weighing 2.73 Kg) -1 No. 8. 18`` wall Brush Nylon/ Standard curved Poly Bristle wall Brush-1 No. 9. Leaf net Deep Deluxe/ Heavy Duty Deep rack aluminium handle-1 No. 10. HI grade stainless steel Algae Brush 10``-1 No. 11. Basic PH and CI test kit All above items make:- Pentair, Halbert, Astral, Hayward.

Providing and fixing bib cock with valves flanged ARI-390378, complete in all respect. Make: Jaquar

Supplying and Installation Skimmer for cleaning/ capturing floating debris such as leaves flower, dirt etc. make intex wall features Automatic 9 pounds of size 75 x 10.25 x 8.25 inch of flow rate 9 M3/hr for concrete /Vinyl Pool Materials ABS connection 1- ½`Threaded (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make:- Pentair, Halbert, Astral, Hayward.

Providing and fixing angle valves model -ARI-39053, complete in all respect Make:- Jaquar

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 6 Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing complete in all respect. Make:-Supreme/Finolex 90 mm dia

Providing and fixing table top basin (WHB) Model-AVIOR/R Italian size 59.5 x 42 x 15.5 cm, complete in all respect.

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 6 Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing complete in all respect. Make:-Supreme/Finolex 110 mm dia

Supply G.I union coupling of 15 mm i/dia

Supplying, Installation, Testing and Commissioning of uPVC pressure pipes of 6 Kgf/cm2 pressure including fittings, tees, bends, socket, clamps, coupling and adaptors supports etc. and jointing with solvent joint, testing complete in all respect. Make:-Supreme/Finolex 160 mm dia

Supply G.I union coupling of 25 mm i/dia

Supply G.I union coupling of 50 mm i/dia

Supply of life jacket Make:- Pentair, Halbert, Astral, Hayward.

Supply of Ring type Life Buoy swimming Tubes Make:- Pentair, Halbert, Astral, Hayward.

Supply G.M Peet valve 15 mm i/dia

Supply of foldable strecher Make:- Pentair, Halbert, Astral, Hayward.

Supply of first aid kit Make:- Pentair, Halbert, Astral, Hayward.

Supply G.M Peet valve 25 mm i/dia

Supply GM Peet valve 50 mm i/dia

Providing and fixing PVC Floor Trap of 100 mm o/dia outlet (Heavy duty) of PRINCE/ SUPREME/ SKIPPER make

Supply of CPVC Control valves/ ball valve with brass internals of PRINCE/ SUPREME/ SKIPPER make. (c) 40 mm

Supply of CPVC union coupling with brass internals of PRINCE/ SUPREME/ SKIPPER make. (NS) (a) 25 mm

Supply of CPVC union coupling with brass internals of PRINCE/ SUPREME/ SKIPPER make. (NS) (b) 32 mm

Providing and fixing PVC elbow of size 4` PRINCE/ SKIPPER/SUPREME make.

Supply of CPVC union coupling with brass internals of PRINCE/ SUPREME/ SKIPPER make. (NS) (c) 40 mm

Supply and fixing 40 mm dia PVC waste pipe of best quality, complete in all respect as directed by the Engineer In-charge.

Supply of CPVC union coupling with brass internals of PRINCE/ SUPREME/ SKIPPER make. (NS) (d) 50 mm

Providing and fixing soap dish Jaquar make AKP-35731P.

Supply of CPVC Control valves/ ball valve with brass internals of PRINCE/ SUPREME/ SKIPPER make. (NS) (a) 25 mm

Providing and fixing health faucet Jaquar make ALD-565.

Supply of CPVC Control valves/ ball valve with brass internals of PRINCE/ SUPREME/ SKIPPER make. (NS) (b) 32 mm

Providing and fixing over head shower Jaquar make OHS-1709

Providing and fixing C.P. grating standard make 5` size.

Supply and fixing of PVC Gully Trap of 100 mm dia size 4’’ i/dia with cover and frame (Heavy duty) of PRINCE/ SUPREME/ SKIPPER make.

Providing and fixing towel Rail Jaquar make ACN-1111 SM 600 mm long

Supplying, Installation, Testing and Commissioning of eye ball type Floor Inlet to Provide filtered Water to the Pool Floor inlet 2` slipwith 1.5` slip bushing, 3500-4000 Litre Discharge of Water Per Hour suitable for 10 kgs pressure, Colour - white/off-white (including the cost of all other petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge). Make: Pentair, Halbert, Astral, Hayward.

SKG INFRATECH PRIVATE LIMITED