CERTAIN REPAIR TO ROOF TREATMENT, SUNKEN, FLOORING, ROOFING AND MISC WORKS AT JCOs/OR MD ACCN UNDER AGE B/R II OF GE SUKNA

Amount

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in roof kerbs, rounded or chamfered on haunching in chajjas to prevent water seepage into brick walls, including necessory formwork and scafolding upto a height of 8 mtr including demolition of existing PCC complete all as specified and as directed.

M&L PCC 1:2:4 type C-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheets and brick wall, thickness of concrete bed exc. 5 cm and not exc.10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork ht up to 7m complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for burnt Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed.

M & L for applying evenly a coat of blown type bitumen @ 1.50 Kg per Sqm including cleaning of surface and binding with clean dry sand @ 0.05 cum per Sqm including 150 micron Polythene film thick laid on a coat of bitumen primer, @0.30 to @ 0.50 kg per Sqm complete all as specified & directed.

M& L for cutting chases in bricks wall, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L 18 to 20 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 Sq. cm and not exceeding 13 Sq. Cm complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea) / Chickerassy (Chukrasia Tabularis) / Siris (Albizzia procera) / Kalasiris (Albizzia Odoratissima)

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down and refixing in the same opening shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed. (Note-Renewal of builder's hard?ware articles, if specially ordered, shall be paid seperately for as 'supplied only' rates)

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified and directed.

S & F in repair MS Helical door spring 150 mm size including roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Hasp and staple 100mm safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F in repair towel rail 20 mm dia type brass chromium plated 600mm long between flanges complete all as specified and directed.

S & F in repairs towel ring of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (minimum weight 90 gms) complete all as specified and directed.

S & F in repairs Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S & F Ball catches with 8 mm dia., steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repair kitchen plate rack made out of 0.63 mm stainless steel sheet & of size not less than 24'' x 30'' x 10'', standard quality fixed with brass screw complete all as specified and as directed. Make :- M/s Bluestar sanitary industries pvt ltd, M/s Prabhat sanitary pvt ltd (Brand IDOOS), M/s JMD international (Brand D-Sons).

S&F in repair curtain harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc with two nos of scoket end caps and brakets (decorative type) for doors/window opening complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Joints, channel, angle, flat iron or tee sections, fixed independently, with connecting plates, etc. confirming to Fe 410 -W (Gde-250 quality A) complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed.

S&F aluminium powder coated frame work (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates and including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc, complete all as specified and directed.

S&F powder coated aluminium window (two track) sliding type without sash bar, and ventilator shutters, (lower type), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 4 mm thick E-board (designer pattern)celing of size 60x60 cm, fixed or laid / inserted to aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with including dismantling of old ceiling board complete all as specified and directed.

S&F in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination and other side balancing white laminated fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 20 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc and laid fair in alternate bays and in including filler joints with sealing compound grade 'A' if required finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, etc complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floorings complete all as specified and directed.

Roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc. and applying neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 10 mm thick in CM 1:3 complete all as specified and directed.

M&L coloured glazed ceramic tiles 450 x 300 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 including roughening of surface complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick as in floors, set and jointed over and including 15 mm thick screed bed in CM 1:6 and pointed in grey cement and pigments to match the colour of tile complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 10 mm thick on brick or concrete surfaces etc in cement mortar 1:4 using WPC at all around and base of sunken floor with proper slope complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L complete removal of existing treatment surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L preparation of old decorated wall surfaces and applying one coat of oil bound distemper complete all as specified and directed.

M&L preparation of old decorated wall surfaces and applying one coat of white wash complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of primer complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4 mm thick tinted glass of any size with aluminium bedding and complete all as specified and directed.

S&F 4 mm thick frosted / pin headed glass in ventilator shutters complete all as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old decorated wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coats of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors including taking up or down complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors including taking up or down complete all as specified and directed.

M&L in repairs High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S&F in repairs 15 mm bore bib tap chromium plated long body fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S & F in repair 15mm bore stop valve, cast copper alloy, with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair 15 mm bore stop cock / angle stop cock fancy type, chromium plated, cast copper alloy, concealed type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs stainless steel Grating doom 100 mm dia with waste hole chromium plated complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 600 mm & suitable for cold/hot water supply complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S & F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S & F in repairs Wash down water closet (Pedestal pattern) white vitreous chinaware complete including connecting to flushing cistern and flush pipe including plastic seat cover white closed pattern with flat bottom and mild steel CP or aluminium anolised hinged device, complete all as specified and as directed.

S & F in repairs Vitreous China Squatting pan of Orissa pattern, size 580x440 mm size white with integral foot rest with Cast Iron `P' or `S' trap, front or back inlet and including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete bedding complete including making good to floor (excluding flushing cistern and flush pipe)all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets & flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repairs health faucet 12 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook and connection with angular stop cock complete all as specified and directed.

Demolition of brick work in cement motor including pillar etc below / above ground level etc complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (Contd...)

(iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

SHANTI UDYOG

M/s TALCO

PS ENTERPRISE

MS ORIENT ENGINEERING WORKS

M/S B B CONSTRUCTION

M/S RANEN PAL

M/s T K Das

D K SARKAR

Embee associates