SPL REPAIRS TO BLDG No P-30/A and P-30/B SINGLE LIVING NURSING OFFICERS ACCN OF CH CC UNDER GE E/M LUCKNOW

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed by Engineer-in-Charge

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge

M&L for 40mm thick PCC type B-1 1:2:4 ( 20mm graded agg) finished even and smooth with using extra cement incl glass dividing strips complete all as specified and as directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like complete all as specified and directed by Engineer-in-Charge

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed by Engineer-in-Charge

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate ) as in roof kerbs /padding or similar work or mud stops rounded or chamferred on edges.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for RCC type B1 1:2:4 (using 20 mm graded stone aggregate) as in parapet walls, beams and columns, slabs, landings, balconies, canopies, deck slabs in shelves and chajja and the like incl necessary form work complete all as specified and directed.

M&L for mild steel TMT reinforcement bars of grade FE-500, 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or securing with clips complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even complete all as specified and directed by Engineer-in-Charge

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work surface finished even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge (Note : Integral WPC shall be measured and paid seprately )

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed.

M&L for Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of primer all as specified on walls surface Incl a coat of 2 mm wall care putty, complete all as specified and directed.

M&L for preparation of new plastered surafce of walls and applying two coats exterior emulsion weather coat paint of make Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac) over one coat primer including 1 mm thick wall care putty complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premishes complete all as specified and directed by Engineer-in-Charge

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed in CM 1:6 complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

M&L for vitrified ceramic tiles 10 mm thick (square /rectangular ) polished dark shade, area of each tiles not exceeding 0.36 sqm, in floor etc. set and jointed in neet cement slurry and pointed white or coloured cement to match the dark shade of the tiles, with and including screed bed in CM 1:6, 15 mm all as specified and directed.

All as per item No. 22 above but as in skirting including 10mm thick rendering in CM. 1:4 as backing coat etc complete.

M&L 18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

M&L 18-20mm thick machine cut Kota stone slab as in skirting /riser over rendering 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge (Note : Rendering will not be measured and paid separately)

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 20mm thick in cement mortor 1:4

Taking down chowkhats or frame (wooden/aluminium/PVC) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit all as specified and directed.

Taking down chowkhats or frames (wooden/aluminium/PVC) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed by Engineer-in-Charge

S&F well seasoned 2nd class hard wood plan, solid, straight chowkat and frames, wrought framed, rebate on the solid rounded or chamfered, put together with glue pinned at joint complete all as specified and directed by Engineer-in-Charge

S&F for Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole all as specified.

M&L for plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary formwork complete all as specified and directed by Engineer-in-Charge

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

S&F 30 mm thick second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc , divided in to square with plain chamferef or rounded mitred and rebate sash bars, any numbers edges of framing plain, chamfered or rounded, size / section of members of shutters shall be as specified in SSR Part I section 8 clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge

S&F 30 mm thick second class hardwood glazed shutters as in windows/vertilators open rebateed and prepared to received mitred aand secured sash bars any numbers edges of fsdraming plain chamfered of rounded in SSR Part I Section 8 caluse 8.24 (b).complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise desceribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F aluminium anodised sections ( conforming to IS) door with frame of size 100mmx 44.45mm wide fabricated with 2mm thick section , double/single leaf shutter with 44.45mm wide fabricated with 2mm thick section having vertical and top rail 83.50mm, bottom rail and middle rail 115mm and including necessary jointing cleats, screws, neosprene rubber beading, PVC packing, with 3 mm thick Aluminium composite panel, 100 mm butt hinges (3 Nos in each shutters), 150mm tower bolt (1 in each panel), locking arrangements with 100 mortice lock complete all as specified and directed.

S&F aluminium anodised sections sliding windows shutters with frames comprising Series -C (20mm), 3 track sliding shutters duly fitted with neoprene beading, glazing clips, locking device, 4.8mm thick heat absorbing glass panes in 2 shutters and 0.46mm dia SS wire mesh in one shutter complete all as specified and directed. (Note :- Thickness of aluminium section minimum 2mm)

S&F in repairs aluminium anodized grill weight of 3.13 Kg per Sqm (min) with suitable aluminium anodized frame of F/H section of 0.297 Kg per Meter (min) with suitable fixing screws / attachment etc complete all as specified and directed.

S&F in repair 18/19 mm thick commercial plywood, BWR, type BB interior grade both side fixed with screwed to timber frame work edge chamfered including beading/battens as required complete all as specified and directed.

S&F in repair 12 mm thick commercial plywood, BWR, type BB interior grade both side fixed with screwed to timber frame work edge chamfered including beading/battens as required complete all as specified and directed.

S&F 0.9 mm thick Decorative laminate (sunmica) type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction as complete all as specified and directed.

S&F for 30 mm width of flaps continuous piano hinges MS bright finish are electroglavanised complete all as specified and directed.

S&F in repair magnet catcher heavy duty for cupboard door shutter complete all as specified and directed.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed.

S&F for PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specn & drg

S&F for factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified.

S&F 75 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 100 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 100 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge

S&F Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 300 mm long, mild steel, rat tail rod pattern springs including roller and roller plates complete all as specified and directed by Engineer-in-Charge

S&F in repairs Aluminium body (extruded section ) body Door closer hydraulically regulated, designation No. 2 , universal type, suitable for door shutters 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or bricks round, glazed with putty or fixed with bedds complete all as specified and directed by Engineer-in-Charge

S&F 3 mm thick sheet glass, ordinary quality and glzing with oil putty/timber bedds in square in each pane complete all as specified and directed.

S&F for 4.8 mm thick sheet glass odinary qulity and glazing with oil putty/timber bedds in square in each pane complete all as specified and directed.

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty in each pane complete all as specified and directed.

S&F in repair curtain rod, mild steel, chromium plated with fixing brackets, fancy end cap etc, complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20 mm bore complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)15 mm nominal bore complete all as specified and directed.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)20 mm nominal bore complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 in brick work for concealed water tubing, cutting exc 10 cm but nexc. 20 cm girth complete all as specified and directed.

Dismantling water tank capacity exc 250 & n.exc 500 ltr and taken as credit

M&L for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to warf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified.

S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210gms) complete all as specified.

S&F in repairs Chromium plated fancy long body Bib taps with cup, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repair CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipe.

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified.

S&F in repair vitreous China wash down water closet pan (padestal pattern Water Closet ) , ( excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe , etc., complete incl

S&F in repairs Low level flushing cistern, moulded from virgin poly propylene complete all as specified and directed.

S&F in repairs Plastic water closet seat, white, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. embedded in red lead cement, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified.

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified.

S&F in repair PVC floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe).

Taking down pipes (any sizes) incl all fittings

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall complete all as specified and directed.

S&F 160mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall complete all as specified and directed.

Demolition of existing roof treatment of any type, including screed bed etc complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate, (Avg 50 mm thickness) in roof for padding to achieve the 1:40 slope complete all as specified and as directed.

M&L for 15 mm thick screed bed in cement mortar 1:4 over RCC roof slab including mixing only water proofing compound as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge. (WPC will be measured and paid separately)

Supply only Liquid water proofing compound.

M&L for water proofing treatment on roof surfaces in the following manner:- (a) The surfaces shall be painted with hot bitumen grade 30/40 confirming to IS-73 @ 1.20 kg / sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 ltr /sqm. (b) Supply & lay 3 mm thick APP water proofing membrane reinforced with non woven polyester matt laid using bitumen torch by torch application with a side lap of 10 cm & 15 cm end lap weighing not less than 3.5 kg / sqm. Note: - (i) Work to be carried out through authorised applicators of the manufactures and work will be carried out in complete / in patches in roofs (ii) Contractor shall submit written guarantee of 10 years from date of completion & submit security deposit @ 2.5% of executed amount or Rs 6250.00 which ever is more.

M&L for preparation of untreated surface of APP membrane of any description over 10 cm in width or girth, not otherwise described and applying two coat of aluminium paints over one coat primer complete all as specified and directed.

M&L for 230 x 115 x 40 mm thick machine pressed brick tiles laid over & including screed bed 20 mm thick in cement mortar in 1:3 and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, wind Tie etc Fe 410-W (Gde E-250) quality A complete all as specified and directed by Engineer-in-Charge

M&L for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Dismantling of roof sheet (any descriptions) including ridges in roof covering all as specified and directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws as specified

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge

M&L preparation of old painted surface of walls and applying one coat exterior emulsion weather coat paint of Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac) incl 1mm thick wall care putty complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade over and incl 1mm thick wall care putty complete all as specified and directed by Engineer-in-Charge

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Taking down carefully aluminium/Copper conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing complete all as specified.

M&L point wiring for one light/fan/exhaust fan point controlled by one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surfce as existing same colour complete all as specified.

M&L point wiring for one socket outlet point 5 amps on independent board controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly complete all as specified.

Ditto all as above item no -03 hereinbefore but one socket outlet point on same baord with other switches with 1.5 sq mm single core multistranded PVC insulated FRLS cable including 1.5 sq mm single core multi stranded copper cable used as continuous earth wire.

M&L point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly complete all as specified.

S&F Polycarbonate switch piano flush type, SP,5/6 Amps, one way complete all as specified &directed

S&F Polycarbonate switch piano flush type, SP, 16/20 Amps, one way complete all as specified &directed

S&F Polycarbonate socket out let 2 in 1 socket 5 pin, (6 Amps) flush type controlled by one switch,complete all as specified &directed

S&F Polycarbonate socket out let 6 pin, 20 Amps complete all as specified. & directed

M&L ceiling rose, Pilot 3 Plate ceiling rose 6A,complete all as specified & directed

S&F Ceiling Fan 1200 mm sweep AC 230 volts Five star rating single phase (BLDC Type) making connection with two core flat cable 1.0 sqmm PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified

Supply and fixing exhaust Fan made out of sturdy Engineering 300mm sweep AC 230 Volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded cooper wire of appropriate size including testing complete all as specified.

Supply and fixing LED lights fitting 20 watt, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings

S&F plug and socket DBs with Single pole MCBs rated 20 Amps capacity all as specified or equivalent of other make including making niche in wall and mounted flush complete all as specified.

M&L for concealed sub main wiring comprising two single core, 4 Sq mm nominal cross sectional area multi on same copper conductor cable, PVC insulated FRLS Grade unsheathed 1100 Volts grade drawing in and over PVC conduits and conduit fittings complete (concealed type) including S&F 4 Sq mm nominal cross sectional area n green coloure on same copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified (Cutting chases and making good of disturbed surfaces shall deem to be including in the unit rate quoted by tendered).(Note :- Extra length of cables/wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly)

M&L for concealed sub main wiring comprising two single core, 06 Sq mm nominal cross sectional area multi on same copper conductor cable, PVC insulated FRLS Grade unsheathed 1100 Volts grade drawing in and over PVC conduits and conduit fittings complete (concealed type) including S&F 4 Sq mm nominal cross sectional area n green coloure on same copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified (Cutting chases and making good of disturbed surfaces shall deem to be including in the unit rate quoted by tendered).(Note :- Extra length of cables/wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly)

S&F distribution board TPN ,with and including of DPX MCCB 25 KA 125 amps MCCB FP, as incomer and SP/TPN going protection class IP 54, 8nway (DPX125+24) with metal double door all as specified and directed. Note: FPMCCBs 25KA 125Apms 1No and 24 Nos MCB SP 32 Apms 230 Volts and Blanking plate shall be measured and under this items.

S&F epoxy powder coated distribution box Double door type SPN 4 way,with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door all as specified and directed.

S&F MCB SPN, 40 Amps , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each all as specified and directed

S&F MCB SP 6 to 32 Amps C seires , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each all as specified and directed

Taking down existing Gyeser and installing at given location after plastering and replacement of power box etc

Supply & installing Water Heater Storage type with copper inner tank and heating element upto 2KW capacity 25 Ltr. BEE 5 Star rated complete with all accessories such as safty valve thermostate NRV, connection piece etc.

Supply and fixing electronic meters temper proof LCD display with polycarbonate cover 230 V,0-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP -54, with parameters to show data ,time, current reading , load PF , voltage and KWH

M/s Sahu Associates (BID ID -3286184)

M/s Vatsh Raj and co (BID ID -3287016)

kaushalya construction (BID ID -3287236)

rajan construction (BID ID -3285338)