Execution of Renovation work at Ground Floor of the Institute building at National Institute of Public Cooperation and Child Development, Hauz khas

Total Amount Including GST ₹ 93,18,683.48

S DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL TOTAL

NO 2023 AMOUNT AMOUNT

DSR (INR) NON-DSR

1 DISMANTLING (INR)

Dismantling tile work in floors and roofs laid in

1.1 15.23 cement mortar including stacking material

within 50 metres lead.

For thickness of tiles above 25 mm and up to

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres lead:

15.12.1 Of area 3 sq. metres and below EACH 28.00 367.20 10,281.60

Dismantling wooden/aluminium / Gypsum

partitions,/ doors, windows, fixed glazing and

false ceiling including disposal of

unserviceable surplus material and stacking of

serviceable material with in 50 meters lead as

directed by Engineer-in-Charge.

Carriage of material by mechanical transport

including loading unloading and stacking

1.1.1 Lime, murrum, building rubbish

TOTAL OF DISMANTLING 36,149

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-CIVIL

DSR/ MR AMOUNT AMOUNT

S NO DESCRIPTION QUANTITY UNIT RATE

DSR ITEM NON DSR ITEM

1 FLOORING WORKS

Providing and laying in position CEMENT CONCRETE of specified grade exluding the

1.01 4.1 cost of centring and shuttering-all work upto plinth level.

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing , supply and laying 10 mm thick play area floor (009 & 007 mat size

MR 300mmx300mm interlocking with high density foam.non toxic BPA 59 sqm 2200.00 129800.00

Providing and laying vitrified floor and wall tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm

1.04 11.41A thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry

@ 3.3 kg/ sqm including grouting the joints with white cement and matching

pigments etc., complete.

MR Providing and laying vitrified Tactile unglazed porcelain floor with water absorption

less than 0.05% a of approved make, in yellow colours , laid on 20mm thick cement

mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/

1.05 sqm including grouting the joints with white cement and matching pigments etc.,

Size of Tile 300x300 mm 15 Sqm 950 14250.00

TOTAL FLOORING WORKS 262562.00 144050.00

2 FALSE CEILING WORKS

Digitally signed by AMIT

Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27

mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the

ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made

out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at

450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing

of gypsum board to ceiling section and perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing compound in 3 layers covering

upto 150 mm on both sides of joint and two coats of primer suitable for board, all as

per manufacturer's specification and also including the cost of making openings

for light fittings, grills, diffusers, cutouts made with frame of perimeter channels

suitably fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I)

:2011 (Board with BIS certification marks)

Digitally signed by AMIT

BAFFLE CEILING: Providing & Installation of Baffle ceiling system comprises of

50mmx100mm (50 mm width & 100 mm Height) U Shape panels in RAL color finish.

Panels shall be made of 0.5 mm thick galvanized steel after Powder-coated and

length up to 4000 mm. Panel shall be high corrosion resistance and good color

stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to roll

formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-

coated color with cutouts to hold the panels in module of 50 mm at maximum 1200

m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized steel

wire rod hanger with special height adjustment suspension clip at max. 1200 mm

c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts.

Panels are factory cut in lengths up to maximum 4.0 m to suit site dimensions or

shop drawings. Top cap and side cap are used to cover the edges of the panels.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in

true horizontal level, suspended on inter locking metal grid of hot dipped

galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive)

consisting of main "T" runner with suitably spaced joints to get required length and

of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm

center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum)

sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form

a grid of 1200x600 mm andsecondary cross "T" of length 600 mm and size 24x25 mm

made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the

1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3

mm and laying false ceiling tiles of approved texture in the grid including, required

cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats

of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash

fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30

x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width

of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for

all heights as per specifications, drawings and as directed by Engineer-in-charge.

Digitally signed by AMIT

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595

mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of

12.52.1 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated 125.00 sq m 1902.95 237868.75

of thickness 60 microns

(minimum), including factory painted after bending

TOTAL FALSE CEILING WORKS 468354.75 0.00

3 WALL FINISHES WORKS

Supply and installation of Aluminium Framed Glass Partition for Access and Cabin

System for minimal frame, room dividing solutions.Single glazed mullion free

demountable glass partition using Toughened/ Laminated glass in proprietary

natural anodised/Black aluminium sections ALT 50 of size 50mm x 30mm with

Concealed sealing (No visible Gaskets/Seals) with acoustic rating of Minimum 32

db with third party test certificate. The profile will have Carpert Groove at the

Bottom on both sides for accomodating max. 8mm carpets. THe Glass to be fixed

with help of Proprietary Stability GRIPPER Clamp to have a stable system. It should

consists of intermediate slim junction profiles for Glass to Glass vertical joints, 90

Degree L Junction and T Junction profiles suitably to be used as per room

configuration designs.No VISIBLE Clip Lines to provide clutter free view at both side

of section. The Glass to be Offset mounted towards outer edge leading to minimum

aluminium frame on one side. Optional Profile Bottom Seal pair for additional

accoustic. Glass thickness-10 (LSG).shall be included in the product.

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

3.02 9.1 fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 1.00 cu m 142949.70 142949.70

Providing and fixing specified wood frame work consisting of battens 50x25mm

fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming

3.03 8.27 coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 0.23 cu m 187277.65 43073.86

Digitally signed by AMIT

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class hard

3.04 9.21 wood and well matched commercial 3 ply veneering with vertical grains or cross

bands and face veneers on both faces of shutters:

35mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

3.05 9.23 on all edges of flush door shutters (over all area of door shutter to be measured). 20.00 Sqm 462.35 9247.00

Providing and Fixing 1236-22X922 mm Dtype Handle Material : Stainless Steel. Finish

: Satin Stainless Steel (SSS). of approved make and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing SS Mortise Lock Body SB/TB for door thickness 25-50 mm for

3.07 MR wooden doors of approved make and model all complete as per the direction of 10.00 Each 895.62 8956.18

Engineer-in-charge.

Providing and Fixing Double cylinder Floor Spring- for with Closing Force EN 3 with

Maximum door weight 105 Kg. Maximum door width 950mm.Closing speed : 130°

Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor

spring approx : 6kg, 5,00,000 cycles Tested with 5 Years Warranty against

manufacturing defect. CE certified for wooden doors all complete as per the

direction of Engineer-in-charge.

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with

10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete

3.09 9.53 block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone 34.00 Each 228.85 7780.90

aggregate 20mm nominal size).

Providing and Fixing top and Bottom Strap for wooden doors of approved make

3.10 MR and model all complete as per the direction of Engineer-in-charge. 10.00 Each 750.00 7500.00

Providing and Fixing Dead lock Back set- 50 mm with Key Hole for wooden doors

of approved make and model all complete as per the direction of Engineer-in-

Digitally signed by AMIT

Providing and Fixing Double cylinder Floor Spring with Top-Bottom Patch,pivot and

Bottom Patch Lock Maximum door weight 100 Kg. Maximum door width 1000

mm.Closing speed : 120°,Final closing speed : 15-0°. Hold Open (standard): 90° hold

open.Suitable for 10-12 mm glass

3.13 MR Weight of floor spring approx : 6kg 10.00 Each 6500.00 65000.00

5 Years Warranty against manufacturing defect with 5,00,000 cycles Tested

approved make and model all complete as per the direction of Engineer-in-

Providing and fixing 12mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom

pivot & double acting hydraulic floor spring type fixing arrangement and making

necessary holes etc. for fixing required door fittings, all complete as per direction of

3.14 21.18 Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). 20.00 Sqm 5325.90 106518.00

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special

CRYSTAL-effect film to reproduce Sand-blasting effect on glass with customised

designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive

having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C).

Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic,

3.15 MR Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs 15.00 Sqm 1980.00 29700.00

(indoors) must be endorsed by 3M India Limited Architectural Market Department.

Contractors payment wouldn't be released until & unless he/she produces orginal

warranty certificate from the manufacturer.

Digitally signed by AMIT

Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of

approved color by Architect/ Client / Customer, fixed with compatible neutral

grade silicon on a perfectly levelled 12mm thick water proof marine plywood / MDF

/ Mineral fibre board which is mounted on RCC wall/any other structure.

Lacquered glass must be made industrially (using curtain coating process); opaque

(if viewed against a support wall), uniformly coated with PU lacquer (50 micron

thick coating or more); panel to panel colour consistency (measured by photo

3.16 MR spectrometer); highly durable (passes hardness test for minimum 220 oscillations); 0.00 Sqm 3850.00 0.00

humidity resistance (conforms to BS EN 1036 1999 or equivalent) ;

environmentally friendly having Low VOC (no lead, no arsenic, no copper, no

formaldehyde), low VOC content <100g/l. Silicone used should not react with

lacquer coating (compatible neutral cure silicon)

Providing & supplying of Window Blinds as per the approved sample in required

shade and style consisting, of Roller Blinds comprising of optima screen Fabric

comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m,

Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance standard – NFPA 701-

89 small testing ISO-5659-2 .The tear resistance should be complying to ISO4674 &

breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick,easy and

safe installation,moulded plastic with steel spring support and inserted into the tube

end. It shall be driven by a ball chain pulley with ball chain and can be positioned

at right side or left hand side of the Shade. The Shade when lowering or raising,

shall be automatically locked in position upon release of the ball chain by means

of a built in friction lock.Universal clutch for left and right hand operation.Chain

Gear Ratio of 1.75:1.The END PLUG shall be molded of plastic witha steel location

pin. The plug shall be inserted into the tube end. (Opposite to the Drive Unit) for

ease of installation. TheSUPPORT BRACKETS shall be of coated steel & provided with

covers and used in right hand or left hand positions differentiated by the

acceptance of the of the rectangular drive unit support or the round idler plug

pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The

Bracket should be protruding outside maximum of80mm.The ROLLER TUBE shall be

of extruded aluminum with 37mm internal diameter & skin thickness of 1mm and

shall incorporate a key way integral with the tube to accommodate the spline. The

BOTTOM RAIL shall be a Flat Bottom made up of powder coated steel. The

BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls moulded

co-axially to it on 6mm pitch to form an endless ballchain.It is used for raising or

lowering action of the shades.

Digitally signed by AMIT

PELMET: Fabricate and install pelmet made of 19 mm thick board, up to 300 mm

high and in line with external glazing as per details of Architect. Rate to include

finishing exposed surfaces of the Pelmet with enamel paint of approved shade or

Providing and fixing partition upto ceiling height consisting of G.I. frame

and required board, including providing and fixing of frame work made of

special section power pressed/ roll form G.I. sheet with zinc coating of

120 gms/sqm(both side inclusive), consisting of floor and ceiling channel

50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with

MR dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or 20.00 SQM 1400.00 28000.00

metal screws with nylon plugs and the studs 48 mm wide

having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed

vertically within flanges of floor and ceiling channel and placed at

a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing

of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing of 450

75mm overall thickness partition with 12.5 mm thick double skin tapered edged

plain Bison board conforming to IS: 2095: (part I): 2011 (Board with BIS certification

PLYWOOD PANELLING- Plywood panelling using 12mm fire retardant Ply fixed on

one side on Aluminium Frame 50mm x 25mm as per approved sample and

architectural drawings. Aluminium frame to be fixed to walls, floor and RCC Ceiling

using fastners.

LAMINATE CLADDING- P/F 1 mm thick laminate including 4 mm thick MDF as per the

pattern or design required at site on an existing Plywood surface, complete with

filling of grooves with matching or contrast color, as per the direction of the

engineer in charge.

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool

conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G

12.62 Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and 20.00 SQM 322.50 6450.00

in position by criss cossing GI wire etc. complete as per directions of Engineer-in-

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

6.13 designation 7.5 in superstructure above plinth level up to floor V level.

Digitally signed by AMIT

Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

3.20 6.15 course of half brick masonry. 30.00 Sqm 104.80 3144.00

12 mm cement plaster of mix :

1:4 (1 cement: 4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered

3.22 13.26 surface to prepare the surface even and smooth complete. 600.00 Sqm 262.70 157620.00

Wall painting with acrylic emulsion paint of approved brand and manufacture to

give an even shade :

Two or more coats on new work

4.00 UPVC Windows

Providing and fixing factory made uPVC white colour fixed glazed windows/

ventilators comprising of uPVC multi-chambered frame and mullion (where ever

required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild

steel section made from roll forming process

of required length (shape & size according to uPVC profile), ,uPVC extruded

glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size

for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless

steel screws etc. Profile

of frame shall be mitred cut and fusion welded at all corners, mullion (if required)

4.01 shall be also fusion welded including drilling of holes for fixing hardware's and

drainage of water etc. After fixing frame the gap between frame and adjacent

finished wall shall be filled with weather proof silicon

sealant over backer rod of required size and of approved quality, all complete as

per approved drawing & direction of Engineer-in-Charge. (Single / double glass

panes and silicon sealant shall be paid separately). Variation in profile dimension in

higher side shall be accepted

but no extra payment on this account shall be made.

uPVC frame, sash and mullion extruded profiles minus 5%

tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Fixed window / ventilator made of (small series) frame 47 x

9.147B.1 50 mm & mullion 47 x 68 mm both having wall thickness of 47.00 Sqm 8106.30 380996.10

1.9 ± 0.2 mm and single glazing bead of appropriate

Digitally signed by AMIT

GRAND TOTAL 1823784 897426

GRAND TOTAL 1823784 897426

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

1.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface / recessed medium

class PVC conduit, with modular switch, modular plate, suitable GI box and earthing

A.1 the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as

1.55 Wiring for group controlled (looped) light point/ fan point/call bell point (without

independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor

A.2 single core cable in surface / recessed PVC conduit, and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq.

mm FRLS PVC insulated copper conductor single core cable for loop earthing as

1.24 Supplying and fixing following modular switch/ socket on the existing modular plate &

switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 100 122.00 12200.00

1.24.5 6 pin 15/16 amp socket outlet Each 40 197.00 7880.00

A.5 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch Each

box excluding modular plate as required. 30 40.00 1200.00

1.27 Supplying and fixing following size/module, GI box along with Modular base & cover plate

on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

FR PVC insulated copper conductor, single core cable in surface/ recessed medium

class PVC conduit

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 50 233.00 11650.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 20 334.00 6680.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 150 439.00 65850.00

40192 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 120 1005.00 120600.00

Digitally signed by AMIT

40557 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 1

Supply, fabrication and fixing of steel frame work in position for cable tray/Panels

fabricated out of 10 mm dia GI rods, ISA-40 MS angle iron, ISMC-50 channels, flats

etc.complete with providing of Anchor fastners and all necessary hardwares as required

7.1 for fixing, including cutting, bending, welding, drilling, bolting etc. as per design as

required and painted with one coat of primer and two coats of enamel paint of approved

Supply and fixing of Perforated type 2mm thick Hot dip Galvanised G.I. cable tray

of following sizes complete with bend/tee joints, coupling plate & nuts bolts etc.

as required for fixing and including the cost of providing loop earthing with 2 nos.

50 mm x 6 mm GI earth strips complete as per specifications, as required and as

7.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)

Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway

with internal partition/compartmentized of the following sizes including providing

removable 3 mm thick GI cover, knock out holes and fixing accessories earthing with 8

SWG copper earth wire complete as required including floor supports, bends, access

boxes, tap off boxes and cross over as per specification and site requirement.

(overhead / wall mounted recovery & function boxes shall be 1.6 mm thick)

150 mm wide x 38 mm deep raceway

Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box

7.4 including providing 3 mm thick stainless steel cover as per specification. Nos. 6 1,537.01 9,222.04

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

D.3 complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel,

MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/ RCCB/ Isolator)

Digitally signed by AMIT

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes

D.5 in the existing MCB DB complete with connections, testing and commissioning etc. as

Charges for shifting of existing EPBAX room to new roo complete as per instruction of

D.6 MR Engg- In charge L.S 1 75000.00 75000.00

Charges for supplying and fixing of 20KVA UPS complete as per instruction of Engg- In -

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - HVAC WORKS

TOTAL AMOUNT TOTAL AMOUNT

TOTAL AMOUNT TOTAL AMOUNT

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE

EM 2018 DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically

sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules,

microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant,

vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the

rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping.

The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall

be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI

conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports,

vibration isolation, cord less remote control etc., suitable for operation on

2 2.0 single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from BMS System. The cooling

capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB

2.4 Corded Remote Each 19 2500.00 47500.00

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T" Joints

4 4 i.e. Refnet Joints/ Header with Insulation for refrigerant piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete

with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including

5 5 accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid

lines, all accessories as per specifications etc. as required :

5.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50 245.00 12250.00

5.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 70 331.00 23170.00

5.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 20 466.00 9320.00

5.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 588.00 23520.00

5.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 20 707.00 14140.00

5.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50 865.00 43250.00

5.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 70 1108.00 77560.00

Digitally signed by AMIT

6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as

Supply, installation, testing and commissioning of PVC drain water with necessary clamps, fittings

8 MR such as bends tees etc. and duly insulated.

40 mm dia (9 mm thick insulation) Rm 400 374.00 149600.00

Total HVAC WORKS

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and commissioning

the following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and

vermin proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA

sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with

segregated bus-bar chamber with tinned aluminium bus bar and including supplying and fixing

following switchgears, meters and accessories, inter-connections, bonding to earth, powder coated

painting and marking as specified. Switch boards complete as per schematic diagram:or its

equivalent as per the requirement of site

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in

G.2 MR the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 100 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored sleeves

and I/C DMC/SMC bus bars supports at required intervals complete for cross section, size supports

& their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 40 Amps, TPN, MCB+ ELCB -2 Nos.

(b) 32 Amps, TPN, MCB + ELCB - 2nos

Panel complete as above Each 1 102895.00 102895.00

Digitally signed by AMIT

WIFI- DATA AND NETWORKING

S NO DSR/ DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL

S NO DSR/ DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL

DSR (INR) NON-DSR

Wi-Fi standard, IEEE’s new 802.11ac Wave 2 specification, and meets the

growing requirements of wireless networks by delivering a better user

experience. The 1830 Series extends support to a new generation of Wi-Fi

clients, such as smartphones, tablets, and high-performance laptops that Nos. 1 68820.00 68820

have integrated 802.11ac Wave 1 or Wave 2 support.

(DSR Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors for

1.53.1) Connectivity of Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250

MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6 METRE 580 57.00 33060.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable Nos.

termination 16 400.00 6400

at Workt table end. Keystone Unshielded Outlet, 180DG C6, Blue

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable Nos.

at Work Station end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow 16 400.00 6400

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable Nos.

termination 16 400.00 6400

at Rack Side. Keystone Unshielded Outlet, 180DG C6, Blue

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable Nos.

at Rack Side end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow 16 400.00 6400

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

for information outlet (I/O) to end user device connectivity.High Speed Gigabit

24AWG U/UTP Patch Cord Blue, LSZH, C6, 2M Nos. 16 400.00 6400

Supply , Installation , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

for information outlet (I/O) to end user device connectivity. (Rack end), High

Speed Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M Nos. 16 400.00 6400

Supply , Installation , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

for information outlet (I/O) to end user Redantant device connectivity.High

Speed Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow) Nos. 16 400.00 6400

Digitally signed by AMIT

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

for information outlet (I/O) to Rack End Redantant device connectivity.High

Speed Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow) Nos. 16 400.00 6400

Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Nos.

Staggred 1 3500.00 3500

Jack Panel for CAT6 cable termination at rack end. Data Active

Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Nos.

Jack Panel for CAT6 cable termination at rack end. Data Active Redandant 1 3500.00 3500

UTP Components for VOICE 0

(DSR Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors for

1.53.1) Connectivity of Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250

MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6 RM 580 57.00 33060.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable Nos.

termination 16 400.00 6400

at Work Station end. Keystone Unshielded Outlet, 180DG C6, (Ivory)

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable Nos.

termination 16 400.00 6400

at Rack end. Keystone Unshielded Outlet, 180DG C6, (Ivory)

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

at Rack End. Keystone Unshielded Outlet, 180DG C6, For Voice Active Riser Nos. 16 400.00 6400

Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Nos.

Staggred 1 3500.00 3500

Jack Panel for CAT6 cable termination at rack end. Voice Active

Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Nos.

Jack Panel for CAT6 cable termination at rack end. Voice Active --- Riser Side 1 3500.00 3500

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

for information outlet (I/O) to end user device connectivity. (Rack end), High

Speed Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M Nos. 2.00 400.00 800

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CCTV

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265

Vandal Proof Dome camera with 2.8 to 12mm

Motorized Lens,Smart IR, up to 30M IR distance,Up to 120 dB

1 MR WDR (Wide Dynamic Range),3D DNR (Digital Noise Nos 6 10000.00 60000.00

Reduction),H.265+, H.265, H.264, MJPEG

2 Supply, Installation, Testing and Commissioning of

8Ch Embedded Network Video Recorder with 4 Sata

MR Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA, RAID, Nos 1 20000.00 20000.00

Redundant power

3 MR SITC of SSD Hard Disk Drive 6TB, 24/7 surveillance category Nos 1 20000.00

Only complete etc as required.etc.all complete. 20000.00

Supply, Installation, Testing & Commissioning of 32" Flat Screen

HD led (24X7) with Interfaces include HDMI, DVI, D-sub,

Component and Composite input as well as RS-232C and

4 RJ45 for extensive connectivity, remote control and wall 1 30000.00 30000.00

mount unit / floor stand complete with making connections

etc complete as reqd.

5 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 1 6200.00 6200.00

MR Supply , Installtion , Testing and Comissioning of sheilded RM 300 57.00

twisted pair CAT 6 cable(STP) complete etc as required 4 pair 17100.00

Total : A - CCTV 153300.00

Digitally signed by AMIT

Electrical Lighting

S NO DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commisioning of Recessed luminaire with LED (Light Emitting Nos

Diode), system power: 28 W, luminous flux of 2800 lm, colour temperature of 6000 K,

Neutral white, 230 V constant current driver, 70% of luminous flux after 50,000 operating hours,

energy-efficient LEDs, CRI

> 80, CRI > 80, THD<5%, P.F>0.95, SDCM 3, direct light emission, Luminaire housing in Aluminium

1 MR Extrution, polyester white powder coat applied over a 5- stage pre-treatment, Opal diffuser 36 2899 104364.00

for glare-free uniform light, integral electronic control gear,

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-

Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W, Luminous flux of

luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature of 4000 K, Neutral white, CRI >

80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LEDs, direct light emission, housing in die-cast aluminium, Polyester powder white

2 coloured coat applied over a 5-stage pre-treatment trim, prismatic diffuser for 128 1395.00 178560.00

homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control

Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

TOTAL 282924.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - FAS

FIRE DSR/ MR DESCRIPTION UNIT QUANTIT RATE TOTAL AMOUNT

FIRE DSR/ MR DESCRIPTION UNIT QUANTIT RATE TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supplying, installation, testing & commissioning of Pcs

intelligent analog addressable photothermal detector

1 17.2.4 complete with mounting base complete as required. 25.00 2,858.00 71450

Supplying, installation, testing & commissioning of Pcs

addressable manual call point complete as required.

Supplying, installation, testing & commissioning of Pcs

17.2.15 addressable horn cum strobe complete as required. 1.00 3,506.00 3506

Supplying, installation, testing & commissioning of fault Pcs

17.2.7 isolator complete with base as required. 1.00 3,270.00 3270

Supplying, installation, testing & commissioning of Pcs

response indicator on surface/recessed MS Box having

two LED, metallic cover complete with all connections 10.00 276.00 2760

etc as required.

CABLES & ACCESSORIES FOR FAS :

Supplying & laying of 2x1.5 sqmm fire alarm armoured RM

cable, 600/1000V rated with annealed copper

conductor having XLPE insulation, steel wire armouring & 36330

FRLS outer sheath complete as required.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - AV & VC

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

MR Charges for supplying of Speaker for Play room 4.1 2 Nos. 8500.00 17000.00

1 Multimedia Speaker Built-in FM Radio Bluetooth,USB

Remote Control Total Output Power: 40W RMS

Digitally signed by AMIT

S No Item Item Description Unit Qty Rate Amount

DSR (INR) NON-DSR

Providing and placing in position mid back chair.The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The

back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn.

Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and

hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm

which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is

Mid back made up of plastic injection moulded nylon with textured top. It shall have Front pivot synchro mechanism with

chair following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position

locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted

through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm

in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.Complete all as per the

direction of Engineer in Charge.

Providing and placing in position high back chair.The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The

back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn.

Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and

hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm

which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is

2 made up of plastic injection moulded nylon with textured top. It shall have Front pivot synchro mechanism with Nos 11 12500.00 137500

following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position

locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted

through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm

in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. This shall come along a headrest from same family. It shall be SCS IAQ certified

for Indoor Air Quality.Complete all as per the direction of Engineer in Charge.

3 Student Chair Ergonomic design High Quality virgin plastic kids chair Nos 30 1000.00 30000

Providing and placing in position of main table of main table with overall size of table 1500 x1575 x 750mm. The

main table shall be of size 1500 x 675 x 750mm. The side unit shall be 900 x 450 x 675mm. The table is made of 25

mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 1mm laminate pressed on to top

with 2 mm edge bending tape. Soft closing access flap within-build power box are provided on work surface for

wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with1mm laminate pressed on to top with 2 mm edge bending tape. The modesty panel is made of 25

mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 1mm laminate pressed on to top with

2 mm edge bending tape. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade

4 and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick NOs 10.00 40000.00 400000

Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 1mm laminate pressed on to

top with 2 mm edge bending tape pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM

long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism.

Handles are provided for ease of opening. Pedestals are provided with lock for security.complete all as per the

direction of Engineer-in-charge.

Digitally signed by AMIT

Providing and placing in position of main table of main table with overall size of table 975x 600 x 750mm. The

main table shall be of size 975 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate

board confirming to IS-14587:1998 with 1mm laminate pressed on to top with 2 mm edge bending tape. Soft

closing access flap within-build power box are provided on work surface for wire management. The ERU top is

made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with1mm laminate pressed on

to top with 2 mm edge bending tape. The modesty panel is made of 25 mm thick MDF one side pre-laminate

5 Asst Table board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 Nos 2 30000.00 60000

mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick

PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade

edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-

laminate board with 1mm laminate pressed on to top with 2 mm edge bending tape pedestal construction is BOX-

BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.

Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are

provided with lock for security.complete all as per the direction of Engineer-in-charge.

Providing and placing in position Kids table. Size 900mmx 900mmx 400mm. Worktop shall be made from 25mm

Student thick MDF one side prelaminate board with 1mm laminate pressed on to top with 2 mm edge bending tape on

Providing and placing in position of reception table with overall size of table 2100 x 1650 x 750mm. The main table

shall be of size 2100 x 750 x 750mm. The side unit shall be 900 x 450 x 675mm. The table is made of 25 mm thick MDF

– one side pre-laminate board confirming to IS-14587:1998 with 1 mm laminate pressed on to top. Soft closing

access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25

mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 1mm laminate pressed on to top. The

Reception modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 1mm

Table laminate pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade

and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick

Pre- laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 1mm laminate pressed on to

top pedestal construction is BOX-BOX-FILE type Handles are provided for ease of opening. Pedestals are provided

with lock for security.Complete all as per the direction of Engineer in Charge.

Reception Providing and placing in position Centre table.The Glass shall be 10+/-0.3mm thick black tinted toughened glass

Centre Table UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in

SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 900mm

Depth=750mm height=450mm.Complete all as per the direction of Engineer in Charge.

seater sofa Providing and Placing in the position of four seaters and two seater long sofa has been designed for visitors.

Providing and Placing in the position of three seaters long sofa has been designed for visitors.

11 Arm Chair Providing and placing in position of Single Chair modern appearance crafted of premium wood in a pleasing tone and matte

& Play rooom Low height hardwood 35 mm platform for placing mattress size 1800mmx900mmx150 40000

Patient Bed hardwood 35 mm bed for patient size 1800mmx900mmx300 20000

Digitally signed by AMIT

18mm thick pre-laminated HDHMR board for durability and strength

Shelves made of 18 mm thickness and back made of 12 mm thickness

Door storage cabinet with lock and key facility with sheves and filing drawers 625000

14 600 mm Depth , 2 tone laminate on shutter SQM 50 12500

18mm thick pre-laminated HDHMR board for durability and strength

Shelves made of 18 mm thickness and back made of 12 mm thickness

Door storage cabinet with lock and key facility with sheves and filing drawers 199500

600 mm Depth , 2 tone laminate on shutter

15 Size- Design as per the engineer incharge SQM 19 10500

18mm thick pre-laminated HDHMR board for durability and strength

Shelves made of 18 mm thickness and back made of 12 mm thickness

Open Storage acility with sheves and filing drawers 84000

16 Size- Design as per the engineer incharge SQM 8 10500

18mm thick pre-laminated HDHMR board for durability and strength

Shelves made of 18 mm thickness and back made of 12 mm thickness

Under staircaseDoor

storage cabinet with lock and key facility with sheves and filing drawers SQM 14 15500 217000

1200 mm Depth , 2 tone laminate on shutter

17 Size- Design as per the engineer incharge

Digitally signed by AMIT

Schedule of Quantities: Signages and Artwork

S No Description Unit Qty Unit price DSR Non-DSR Amount

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of required size and

shape with arrangement of screws in the letters itself for mounting on the walls or pasting

using 3M VHP Tape. Fixing complete as per directions of the engineer. The Sizes would be

calculated in Sqft as per Logo Design provided. Each 1 35,977.00 35977.00

Tentative Size 42"X60"

2 NAME SIGNAGE CHANGEABLE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured wood finish pasted

/White milky acrylic 3mm laser cut pasted on top with proper names/ Departments written

using plottercut vinyl or laser cut acrylic letters in approved colour.Inserting provision for

changing names .Fixing provision using 3M VHP double sided tape as required. Each 22 1,500.00 33000.00

Signage Size 12x5 inch

3 FLOOR DIRECTORY

Providing and fixing of Acrylic signageboard of 5mm Acrylic with textured wood finish pasted /White

milky acrylic 3mm laser cut pasted on top with proper names

/Departments written using plottercut vinyl or laser cut acrylic letters in approved colour. Provision

of fixing screws/ Studs etc or as per the direction of the engineer.

4 FIRE EVACUATION MAP / SIGN.

Providing and fixing of Clear Acrylic sandwich frame of 3mm & 2mm acrylic with Evacuation Plan Each 2 2,673.00

Printed on photoluminescent media and inserted between the two frames. Should be fixed on

the wall using 4 Screw/ SS studs. Size 12 inch x 17 inch 5346.00

5 FIRE ESCAPE EDGE-LIT SIGNAGE

Providing and fixing of Edge-Lit signage with battery backup. Made from acrylic sheet of 8 mm

thickness laser engraved, Transformer to be inbuilt. Maintenance free sealed nickel cadmium

battery included • 120V/277V AC Operation • Crystal clear acrylic face panel• Engraved letters

increase visibility • Anodized aluminum faceplate • Field applied chevron directional indicators Each 2 3,289.00 6578.00

simplify installation • Long life, energy-saving LED lamps • Dual-voltage 120V/277V AC

Operation • UL listed. To be installed at stairs entry. Size 310mm x 175mm

6 FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board sheet at base with

photoluminescent film self adhesive & colored vinyl ( Red/Green) Plotter cut and pasted on top.

Both side / Single Side facing Complete including fixing on wall with screws and washers or hanging

on ceiling with GI chain/GI Bar complete as per technical specifications and directions of Engineer.

a Photoluminescent, Fire Hose Reel - 10"x8" Each 4 435.00 1740.00

b Photoluminescent, Fire Exit / Escape Sign - 18"x6" Each 4 515.00 2060.00

c Photoluminescent, Floor Level - 18"x6" Each 4 515.00 2060.00

Digitally signed by AMIT

d Photoluminescent, Fire Alarm Call Point - 10"x8" Each 4 435.00 1740.00

e Photoluminescent, Fire do not use lift- 10"x8" Each 4 435.00 1740.00

f Photoluminescent Signs, Fire Extinguishers - 10"x8" Each 8 435.00 3480.00

TOTAL 123721.00

Digitally signed by AMIT