RequiredCertificate (Requested in ATC) Bid to RA enabled Yes Track Suits - Sports ( 138 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * MATERIAL Fabric ( Composition ) Polyester Blended with Cotton Polyester Blended with Cotton Percentage of Blending ( in case of Polyester 50 % and Cotton 50 % Polyester 50 % and Cotton 50 % 1/8 Blended Fabric ) Mass ( gram per square mtrs ) 140 200.0
Required140.0 Fabric Construction Knitted Knitted Weave ( In case of Woven Fabric ) Any other weave as per buyer's requirements Any other weave as per buyer's requirements Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Plain ( Single Jersey ) Knitted
RequiredPlain ( Single Jersey ) Knitted
RequiredEnds per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric No Yes
RequiredNo Upper Lining No Yes
RequiredNo Lower Lining No Yes
RequiredNo Lining Material Not Applicable Not Applicable Mass of Lining (Gram per Square Meter) Not Applicable * Netting mesh No of holes on base & bias within 625 Square millimeter Not Applicable * Technical Requirements of Slide Fastener for Upper Closing No Medium special duty Open End as per IS 14181 Latest
RequiredLight Duty as per IS 14181 Latest
RequiredNo Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) No No Slide Fastners are BIS Marked No No Width of Tape Elastic at Waist of Trouser 4.0 cm * Width of Tape Elastic at Bottom of Upper 4.0 cm * 2/8 Technical Requirements of Waist Band No Waist band as per IS 9686- 1980 latest
RequiredNo Waist Draw Cord Nylon Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Rib Knitted Fabric * Upper provided with Piping No Yes
RequiredNo Lower provided with Piping No Yes
RequiredNo Piping Fabric- Composition Any other material as per buyer's requirements * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) 90 90 Embroidery Thread Polyester Polyester SIZE Size Medium (M) Medium (M) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 52.5 cm ( Medium ) * Width Across Bottom Opening (relaxed) 46 cm ( Medium ) * Length at front from top of collar to bottom 66 cm ( Medium ) * Sleeve length (from center of back to bottom of sleeve 84.5 cm ( Medium ) * Sleeve opening relaxed ( Cuff ) Width 11 * Front Neck Drop 9 * Back Neck Drop 2 * Length of Slide Fastener 64 cm( Medium ) * DIMENSIONS OF LOWER Side Seam Length 104.5 cm ( Medium ) * Waist relaxed ( Width Across ) 43 cm ( Medium ) * Waist stretched (Width Across ) 52.5 cm ( Medium ) * 3/8 Seat/Hip ( 15 cm below waist band) 52.5 cm ( Medium ) * Thigh (at Crotch) ( Width Across ) 36 cm ( Medium ) * Bottom Opening ( Width Across ) 22 * Front rise including waist band 28 cm ( Medium ) * Back rise including waist band 38 cm ( Medium ) * Length of Waist Tying Cord 155 * Bottom Fold (Hem) with full turn in(cm) 2.0 * POCKETS Number of Pockets (Upper) Without Pockets Without Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) Not Applicable * Size of Inside Pocket at Chest- Upper Not Applicable * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper No No Number of Pockets (Lower) 2 Side Pockets 2 Side Pockets Size of Side Pockets - Lower ( Length X Width ) ( cm ) Not Applicable * Side Pocket Opening- Lower 15 * Pocket Closure with Slide Fastener - Lower Back Pockets with Slide Fastener Back Pockets with Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement With Canvas Reinforcement * SLEEVE Sleeve Type Set In Sleeve * PIPING Position and Dimensions of Piping on Upper - * 4/8 Position and Dimensions of Piping on Lower - * STITCHING Sewing Thread 125 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in two rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in two rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in two rows with chain stitch on the elastic * Lining seams Not Applicable * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas No * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Multicolour Contrasting Pannels Any other colour as per buyer's requirements * Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Not applicable Not applicable Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * 5/8 Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Any other colour as per buyer's requirements Any other colour as per buyer's requirements Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Not Applicable * Colourfastness to perspiration ( IS 971 )- Mesh Lining Not Applicable * Colour of Piping Material Any other colour as per buyer's requirements * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 2 2 LOGO AND MARKING Logo/Totem Marking No No Type of Logo Not Applicable Not Applicable Number of Logos on Upper Not Applicable 1
Required2
Required3
RequiredNot Applicable Number of Logos on Lower Not Applicable Not Applicable Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Government Lab to prove conformity of products to the specification Yes Yes Test Report No - * 6/8 Test Report Date - * Name of the Lab - * Address of the Lab - * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Yes * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes
RequiredNot applicable * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer. Additional Specification Documents
