Construction of Main Building and Quarter For 100 Beded Sub-District Hospital By Upgrading 50 Beded Sub-District Hospital at Mukainagar, Tal.-Mukatinagar, Dist.- Jalgaon

Amount

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift upto 1.5 metres) By Mechanical Means (Item No. 21.02)

Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift upto 1.50 m) By Mechanical Means (Item No. 21.06)

Providing preconstructional antitermite treatment as per Indian Standards 6313(Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. (Item No. 21.22)

Providing preconstructional antitermite treatment as per Indian Standards 6313(Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per square metre of vertical surface area covering 10 years guarantee on bond paper. (Item No. 21.23)

Providing preconstructional antitermite treatment as per Indian Standards 6313(Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper. (Item No. 21.24)

Providing preconstructional antitermite treatment as per Indian Standards 6313(Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 Cement Mortar diametre about 30-60 centimetres deep at 15 centimetres c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper. (Item No. 21.25)

Providing soling using 80metresilimetres size trap metal in 15 centimetres. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. (Item No. 21.40)

Filling in plinth and floors with approved excavated material in 15 centimetres. to 20 centimetres. Layers including watering and compacting etc. complete. (Item No. 21.36)

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 centimetres to 20 centimetres including watering and compaction etc. complete. (Item No. 21.37)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/granite/quartzite/gneiss metal for foundation and bedding/steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.), with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 24.04)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.Cement Concrete work in foundations like raft, strip foundations, grillage and footings of R.Cement Concrete columns and steel stanchions etc. including bailing out water, Steel centering, formwork, cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided(Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 25.13)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.Cement Concrete columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 25.33)

... (Item No. 25.33, First Floor)

... (Item No. 25.33, Second Floor)

... (Item No. 25.33, Third Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.Cement Concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 25.52)

... (Item No. 25.52, First Floor)

... (Item No. 25.52, Second Floor)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.Cement Concrete slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 25.72)

... (Item No. 25.72, First Floor)

... (Item No. 25.72, Second Floor)

... (Item No. 25.72, Third Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/quartzite/granite/gneiss metal for R.Cement Concrete Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with Cement Mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete.(Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 26.26)

... (Item No. 26.26, First Floor)

... (Item No. 26.26, Second Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.Cement Concrete pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 26.19)

... (Item No. 26.19, First Floor)

... (Item No. 26.19, Second Floor)

... (Item No. 26.19, Third Floor)

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/granite/quartzite/gneiss metal for R.Cement Concrete chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 26.07)

... (Item No. 26.07, First Floor)

... (Item No. 26.07, Second Floor)

... (Item No. 26.07, Third Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/granite/quartzite/gneiss metal for R.Cement Concretecoping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 26.23)

... (Item No. 26.23, First Floor)

... (Item No. 26.23, Second Floor)

... (Item No. 26.23, Third Floor)

Providing cast in situ/ready mix M20 grade cement concrete for head walls of CD work/retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete.(with reversible drum type mixer/concrete batch mix plant(pan mixer) with Supervisory Control and Data Acquisition (Item No. 11.29)

... (Item No. 11.29)

Providing and fixing in position T Metric Tonnes-FE-500 bar reinforcement of various diameters for R.Cement Concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (Item No. 26.33)

... (Item No. 26.33, First Floor)

... (Item No. 26.33, Second Floor)

... (Item No. 26.33, Third Floor)

Providing second class Burnt Brick masonry with conventional/Indian Standards type bricks in cement mortar 1:6 in foundations and plinth of inner walls/in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. (Item No. 27.01)

Providing Autoclaved Aerated Concrete Block masonary of conforming to Indian Standards:2185(Part 3)-1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete.(The test shall be carried out conforming to Indian Standards:6441(Part I)-1972) (Item No. 27.15)

... (Item No. 27.15, First Floor)

... (Item No. 27.15, Second Floor)

... (Item No. 27.15, Third Floor)

Providing Autoclaved Aerated Concrete Block masonary of conforming to Indian Standards:2185(Part 3)-1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete.(The test shall be carried out conforming to Indian Standards:6441(Part I)-1972) (Item No. 27.16)

... (Item No. 27.16)

... (Item No. 27.16, First Floor)

... (Item No. 27.16, Second Floor)

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetres. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete/B.B.masonry and or tying by binding wire etc. complete. (Item No. 32.26)

... (Item No. 32.26, First Floor)

... (Item No. 32.26, Second Floor)

Providing internal cement plaster 12milimetres thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. (Item No. 32.04)

... (Item No. 32.04, First Floor)

... (Item No. 32.04, Second Floor)

Providing and applying plaster with plaster of paris in 6milimetres thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete. (Item No. 32.27)

... (Item No. 32.27, First Floor)

... (Item No. 32.27, Second Floor)

... (Item No. 32.27, Third Floor)

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15milimetres thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8milimetres thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (Item No. 32.11)

... (Item No. 32.11, First Floor)

... (Item No. 32.11, Second Floor)

... (Item No. 32.11, Third Floor)

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6milimetres thickness or Tape Grooves 35 to 45milimetres thickness or as required, in all position including preparing the surface, scaffolding etc. complete. (Item No. 32.32)

... (Item No. 32.32, First Floor)

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. (Item No. 40.01)

... (Item No. 40.01, First Floor)

... (Item No. 40.01, Second Floor)

Providing and fixing frame with/without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300metresilimetres x 40metresilimetres x 5milimetres with oil painting, etc. complete (Item No. 39.01)

... (Item No. 39.01, First Floor)

... (Item No. 39.01, Second Floor)

Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35milimetres thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25milimetres thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete (Item No. 39.08)

... (Item No. 39.08, First Floor)

... (Item No. 39.08, Second Floor)

Providing and fixing 34milimetres thick moulded door shutter consisting of solid core single leaf flush door of 30metresilimetres thickness lipped with 15mm(5milimetres x 3) thick x 30metresilimetres width on one style and top rail and 10metresm(5milimetres x 2) thick x 30metresilimetres width on other style and bottom rails. The inner panels laminated with 2milimetres thick termite proof, water proof and fire resistant moulded Polyvinyl chloride sheet with 2, 4, 6 design in different plain and/or prelim colours on one side after routing the moulded design on flush doors and 2milimetres plain and/or pre lam Polyvinyl chloride on other side using rubber adhesive on flush door and solvent cement adhesive on the Polyvinyl chloride lipping etc. as per direction of Engineer in charge and manufacturers specification and drawing etc. complete. (Item No. 39.48)

... (Item No. 39.48, First Floor)

... (Item No. 39.48, Second Floor)

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9milimetres with lock plate of 3.15milimetres thickness reinforced with 35 x 35 x 5milimetres angle section fitted with sliding bolts and handles for both sides, deep Mild Steel channel section of depth and thickness not less than 65milimetres and 3.15milimetres respectively with hold fast arrangements, Mild Steel Bracket plate 300 x 300 x 3.15milimetres minimum size and shape with square bar, suspension shaft of minimum 32milimetres diameter, hood cover of Mild Steel sheet not less than 0.9milimetres thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete.(Indian Standards 62481979)(Without mechanical gear) (Item No. 39.24)

Providing and fixing 30metresilimetres thick SOLID PANEL Polyvinyl chloride INTERNAL DOOR SHUTTER consisting of frame made out of Mild Steel tubes of 19 gauge thickness and size of 40metresilimetres x 20metresilimetres for stiles, top, lock and bottom rails. Mild Steel frame shall have a coat of steel primers of approved make and manufacture. Mild Steel frame shall be covered with 5milimetres thick heat molded Polyvinyl chloride channel of size 30 x 100metresilimetres forming stiles, and 5milimetres thick, 125milimetres wide Polyvinyl chloride sheets for top rail, lock rail and bottom rail on either side, and 15mm(5milimetres x 3) thick, 20metresilimetres wide cross Polyvinyl chloride sheet as gap insert for top rail and bottom rail. Paneling of 10metresilimetres thick prelam Polyvinyl chloride sheet to be fitted in the Mild Steel frame welded/sealed to the stiles and rails with 30metresilimetres wide x 5milimetres thick Polyvinyl chloride sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5milimetres thick Polyvinyl chloride strip of 20metresilimetres width is to be stuck on the interior side of the C Channel using Polyvinyl chloride solvent cement adhesive. including stainless steel fixtures and fastening Complete as per direction of Engineerincharge, manufacturer'sspecification and drawing. (Item No. 39.81)

... (Item No. 39.81, First Floor)

... (Item No. 39.81, Second Floor)

Providing & fixing factory-made steel door of Single leaf External Embossed Wood finish type with a.) frame of size 100x58milimetres conforming to Indian Standards : 4351-2003, 1.2milimetres thick pre galvanized sheet with mitred and welded cones, frame stretches, hinge reinforcing plates, fixing plates and hardware mounting plates and Polyurethane foam infill b.) Shutter of thickness 46milimetres made of 0.8milimetres thick slip coated pre galvanized steel sheet on both sides conforming to American Society for Testing and Materials A527/American Society for Testing and Materials A525, British Standard 2989 1994, Indian Standards 277, Zinc coating 120 GSM . Lock formed panels with internal stiffeners of 3milimetres thick made of galvanized sheet, 3milimetres thick hinge reinforcing hardware mounting plates and lock protection with Honey-comb craft paper infill of thickness 150 GSM of load bearing capacity 500 Kilogram/square metre. c.) Finish: Powder coated surface finished with thermosetting polyurethane paint of Aliphatic grade of thickness 60-micron d.) Accessories: Min 8 Anchor fastener of HILTI make, min 3 SS Ball Bearing Butt Hinges of Dorset make, Dorset Mortise lock, SS Tower bolt of 200metresilimetres size, Eye hole, Door stopper complete. (Item No. 51.91)

Providing and fixing in position(as per 1868/1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90metresilimetres at weight 0.637 Kilogram/running metre. with window frame bottom track section 92 x 31.75 x 1.30metresilimetres at weight 1.070 Kilogram/running metre.. Top and side track section 92 x 31.75 x 1.30metresilimetres at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25milimetres at weight 0.417 Kilogram/running metre. Inter locking section 40 x 18 x 1.10metresilimetres at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25milimetres at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5milimetres thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box (Item No. 39.44)

... (Item No. 39.44, First Floor)

... (Item No. 39.44, Second Floor)

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38milimetres x 1.22milimetres box type, 5milimetres thick sheet glass louvers, of approved quality etc. complete. (Item No. 39.68)

... (Item No. 39.68, First Floor)

... (Item No. 39.68, Second Floor)

Providing and fixing fly proof mesh shutter toventilator/window using Cement ConcreteTW members of size 45 x 22milimetres for frame work and 35 x 22milimetres for middle support and fixing fly proof mesh on it and covering TW battens of size 20 x 10metresilimetres including priming and two coats of oil painting to the new wood and steel work and all labour charges including all fixture and fastenings etc. complete (Item No. 39.74)

... (Item No. 39.74, First Floor)

Providing and laying telephone black/Amba White/Cadburybrown/Ruby red/Ocean Brown granite stone of 18 to 20metresilimetres thick for door frame/dado/window boxing etc. On Cement Mortar 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. (Item No. 33.68)

... (Item No. 33.68)

... (Item No. 33.68, First Floor)

... (Item No. 33.68, First Floor)

... (Item No. 33.68, Second Floor)

Providing and fixing machine cut machine polished 18milimetres to 20metresilimetres thick telephone black/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. (Item No. 33.35)

... (Item No. 33.35)

... (Item No. 33.35, First Floor)

... (Item No. 33.35, First Floor)

... (Item No. 33.35, Second Floor)

Providing and laying vitrified matt fininsh tiles having size 590metresilimetres to 605milimetres x to 605milimetres of 8 to 10metresilimetres thickness and confirming Indian Standards. 15622-2006(Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. (Item No. 33.42)

... (Item No. 33.42, First Floor)

... (Item No. 33.42, Second Floor)

Providing and laying polished hand cut Kotah Stone flooring 25milimetres to 30metresilimetres thick and 45 centimetres to 55 centimetres wide in plain/diamond pattern on a bed of 1:6 Cement Mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete. (Item No. 33.08)

... (Item No. 33.08)

... (Item No. 33.08, First Floor)

Providing and laying vitrified matt finish tiles having size 590metresilimetres to 605milimetres x to 605milimetres of 8 to 10metresilimetres thickness and confirming Indian Standards. 15622-2006(Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. (Item No. 33.43)

... (Item No. 33.43, First Floor)

... (Item No. 33.43, Second Floor)

Providing and laying matt finish ceramic tiles of having size 30 centimetres x 30 centimetres confirming to Indian Standards15622/2006(group D II-A) and 7 to 8milimetres thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurry cleaning curing etc. complete. (Item No. 33.24)

... (Item No. 33.24)

... (Item No. 33.24, First Floor)

... (Item No. 33.24, Second Floor)

Providing and laying ceramic tiles having size 30 centimetres. x 60 centimetres. confirming to corresponding Indian Standards for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/colour cement slurry cleaning curing etc. complete. (Item No. 33.27)

... (Item No. 33.27)

... (Item No. 33.27, First Floor)

... (Item No. 33.27, Second Floor)

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600metresilimetres x 450metresilimetres size as per detailed drawing including vertical both side polished kadappah stone 25 to 30metresilimetres thick supports with kadappah top 35 to 40metresilimetres thick and polished granite 16 to 20metresilimetres top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetres height and top granite of 75 x 40 centimetres including cutting, opening for sink of required size in kadappah as well as granite etc. complete.(Platform top size 5.00metres x 0.60metres and height is 0.75 m) (Item No. 41.78)

... (Item No. 41.78)

... (Item No. 41.78, First Floor)

... (Item No. 41.78, Second Floor)

Providing 25milimetres to 30metresilimetres thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. b) Both side polish (Item No. 33.33)

... (Item No. 33.33, First Floor)

Providing and fixing machine cut mirror polished 18milimetres to 20metresilimetres thick telephone black granite/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish (Item No. 33.36)

... (Item No. 33.36, First Floor)

Providing and fixing machine cut mirror polished 18milimetres to 20metresilimetres thick telephone black/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone partition with full moulding the edges etc. complete. One side polish (Item No. 33.37)

... (Item No. 33.37, First Floor)

Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity.(With prior approval of S.E.) (Item No. 36.20)

... (Item No. 36.20, First Floor)

... (Item No. 36.20, Second Floor)

... (Item No. 36.20, Third Floor)

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding Indian Standards of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc complete. (Item No. 35.25)

... (Item No. 35.25, First Floor)

... (Item No. 35.25, Second Floor)

Providing and laying damp proof course 50metresilimetres thick in M20 cement concrete layer and bitumen/using cement with waterproofing compound curing, formwork etc. complete. (Item No. 31.01)

... (Item No. 31.01, Second Floor)

Providing cement based water proofing treatment to terraces(Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in Cement Mortar1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with Cement Mortar1:3 admixed with approved water proofing compound and finally top finishing with average 20 milimetres thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300metresilimetres x 300 milimetres making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/-including ponding test etc. complete. (Item No. 31.04)

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12milimetres bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in centimetres 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20metresilimetres thick brick bedding in centimetres mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. (Item No. 31.26)

... (Item No. 31.26, First Floor)

... (Item No. 31.26, Second Floor)

Providing and fixing Orissa Pan of size 580x445x260metresilimetres with approved make flush valve including trap, C.I. soil and vent pipe upto outside face of wall including 100metresilimetres dia. C.I. plug, bend and necessary pipe connection, etc complete. As directed by Engineer in charge. (Item No. 48.38)

... (Item No. 48.38, First Floor)

... (Item No. 48.38, Second Floor)

Providing and fixing white european type wall-hung pan, of size 350metresilimetres x 355milimetres x 570metresilimetres concealed flush tank with floor-mounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100metresilimetres dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc. complete. (Item No. 48.41)

... (Item No. 48.41, First Floor)

... (Item No. 48.41, Second Floor)

Providing and fixing wall-hung white wash basin of size 470x575x190metresilimetres of approved make half pedestal, pillar cock, C.P.Angular stop cock, long thread continental including S.S. bottle trap of having necessary pipe connections up to the outside face of the wall.etc complete. (Item No. 48.45)

... (Item No. 48.45, First Floor)

... (Item No. 48.45, Second Floor)

Providing and fixing Table top white wash basin of size 120x635x405milimetres rubber plugs and brass chain, with pillar cock, C.P.Angular stop cock long thread, continental including S.S. bottle trap of approved make having necessary pipe connection up to theoutside face of the wall.etc complete as directed by Engineer in charge. (Item No. 48.36)

... (Item No. 48.36, First Floor)

... (Item No. 48.36, Second Floor)

Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/union nut etc. complete as directed by Engineer in charge. (Item No. 48.28)

... (Item No. 48.28, First Floor)

... (Item No. 48.28, Second Floor)

Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/union nut etc. complete as directed by Engineer in charge. (Item No. 48.27)

... (Item No. 48.27, First Floor)

... (Item No. 48.27, Second Floor)

Providing and fixing wall mixer with overhead shower, shower arm, hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware/Perryware or equivalent make including all necessary pipes, fittings etc.complete as directed by Engineer In Charge.(Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.) (Item No. 48.34)

... (Item No. 48.34, First Floor)

... (Item No. 48.34, Second Floor)

Providing and fixing 15milimetres dia. screw down bib/stop tap of brass including necessary socket union nut complete. (Item No. 41.40)

Providing and fixing stainless steel sink of size 600 x 510 x 200metresilimetres incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. (Item No. 42.78)

Providing and fixing 10 centimetres Polyvinyl chloride nahani trap with grating etc. complete. (Item No. 42.67)

... (Item No. 42.67, First Floor)

... (Item No. 42.67, Second Floor)

Providing and fixing screw down for 25milimetres dia. wheeled stop tap of brass including necessary sockets/union nut complete. (Item No. 41.45)

Providing and fixing screw down for 32milimetres dia. wheeled stop tap of brass including necessary sockets/union nut complete. (Item No. 41.46)

Providing and fixing screw down for 40metresilimetres dia. wheeled stop tap of brass including necessary sockets/union nut complete. (Item No. 41.47)

Providing and fixing screw down for 50metresilimetres dia. wheeled stop tap of brass including necessary sockets/union nut complete. (Item No. 41.48)

Providing and fixing 15 centimetres x 10 centimetres salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. (Item No. 42.02)

... (Item No. 43.31, First Floor)

Providing, constructing and fixing 450metresilimetres dia. Inspection chamber made up of Polypropylene/polyethylene material of thickness 3.5milimetres and height of 388milimetres with 160 or 200metresilimetres main inlet(s) outlet and 110 and/or 160metresilimetres branch inlets, with 450metresilimetres dia. Ultra shaft pipe of HDPE material having height of 460metresm, having R.Cement Concrete cover and frame fixing in 150metresilimetres thick in c.c.1:2:4, having crushed sand bed of 150metresilimetres thick of size 750metresilimetres dia. Including excavation and refilling the sides of chamber by sand crushed cushioning 150metresilimetres thickness, connecting all required UPolyvinyl chloride fittings with rubber lubricant etc. complete. (Item No. 43.28)

Providing, constructing and fixing 600metresilimetres dia. Inspection chamber made up of Polypropylene/polyethylene material Having 315milimetres diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160metresilimetres and 200metresilimetres pipes having thickness of 5milimetres and 600metresilimetres in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5milimetres having R.Cement Concrete cover and frame fixing in 150metresilimetres thick in c.c.1:2:4, having crushed sand bed of 150metresilimetres thick of size 750metresilimetres dia. Including excavation and refilling the sides of chamber by ?sand crushed cushioning 150metresilimetres thickness, connecting all required UPolyvinyl chloride fittings with rubber lubricant etc.complete. (Item No. 43.29)

Providing and constructing Brick Masonry Inspection Chamber 90 centimetres x 45 centimetres With R.Cement Concrete raft in Black Cotton soil area including cost of reinforcement, 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight with 75milimetres thick R.Cement Concrete cover medium duty 140Kilogrametc. complete. (Item No. 42.17)

RWH-Recharge Pit Providing and constructing recharge pit of 2.0metres deep and 1.0metres dia of pre-cast RCement Concrete rings with 6.5" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid/perforated Polyvinyl chloride casing pipe wrapped around with netlon mesh including 300metresilimetres thick sidefilling around outside of RCement Concrete rings(annular space) with 40metresilimetres size boulders including filling of recharge pit up to 0.5m depth with 25-75milimetres clean washed gravels from bottom up followed by 0.5m depth of 10-25milimetres of clean washed stones followed by 0.5m of washed river fine aggregate(natural sand/crushed sand Vertical Shaft Impactor grade finely washed etc.) including netlon mesh between each gravel/fine aggregate(natural sand/crushed sand Vertical Shaft Impactor grade finely washed etc.) media layer including covering with RCement Concrete slab, manhole frame & cover, Polyvinyl chloride rungs, Polyvinyl chloride end-caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing.The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge. (Item No. 48.47)

Providing and fixing 75milimetres dia stabiliser pipe/Polyvinyl chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete (Item No. 42.51)

... (Item No. 42.51, First Floor)

... (Item No. 42.51, Second Floor)

Providing and fixing 100metresilimetres dia stabiliser pipe/Polyvinyl chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. (Item No. 42.52)

... (Item No. 42.52, First Floor)

... (Item No. 42.52, Second Floor)

Providing and fixing on walls/ceiling/floor 15milimetres dia. CPolyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.55)

Providing and fixing on walls/ceiling/floor 20metresilimetres dia. CPolyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.56)

... (Item No. 42.56, First Floor)

... (Item No. 42.56, Second Floor)

Providing and fixing on walls/ceiling/floor 25milimetres dia. CPolyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.57)

... (Item No. 42.57, First Floor)

... (Item No. 42.57, Second Floor)

Providing and fixing on walls/ceiling/floor 32milimetres dia. CPolyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.58)

... (Item No. 42.58, First Floor)

... (Item No. 42.58, Second Floor)

Providing and fixing on walls/ceiling/floor 40metresilimetres dia. CPolyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.59)

... (Item No. 42.59, First Floor)

... (Item No. 42.59, Second Floor)

Providing and fixing on walls/ceiling/floor 50metresilimetres dia. CPolyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. (Item No. 42.60)

... (Item No. 42.60, First Floor)

... (Item No. 42.60, Second Floor)

Providing and fixing Polyvinyl chloride Rain water pipes of 110metresilimetres outer diameter and having wall thickness of 2.2 to 2.7milimetres confirming to Indian Standards 13592-1992 including proper rainwater receiving recess with Polyvinyl chloride plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25milimetres to 40metresilimetres from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on Cement Concrete or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the Polyvinyl chloride fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (Item No. 42.87)

... (Item No. 42.87, First Floor)

... (Item No. 42.87, Second Floor)

Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20, 000 litres (Item No. 42.54)

... (Item No. 42.54, Third Floor)

Providing, laying and fixing Polyvinyl chloride pipe of 75milimetres dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.27)

Providing and Fixing mat finish stainless steel(of 302 grade) railing with top pipe of 50metresilimetres dia. and vertical pipe of 38milimetres dia at 0.60metres c/c or as required and horizontal pipes of 25milimetres dia in three rows, all pipes of 2milimetres thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75milimetres dia above newel post of 75milimetres diameter etc. complete(Prior approval of sample and brand by Ex.Engineer is necessary before use) (Item No. 40.08)

... (Item No. 40.08, First Floor)

... (Item No. 40.08, Second Floor)

Providing and fixing 450metresilimetres x 550metresilimetres size superior type Belgium mirror with 16milimetres dia. nickel plated towel rod etc. complete. (Item No. 42.20)

... (Item No. 42.20, First Floor)

... (Item No. 42.20, Second Floor)

Providing and fixing heavy duty inter locking concrete Rubber mould glossy paving blocks of 80metresilimetres thickness of having a strength of 400 Kilogram/ Square centimetres. of approved quality and shape on a bed of crushed sand of 25 to 30metresilimetres thick including skirting joints and cleaning etc. complete.(using 100% crushed sand) (Item No. 33.54)

Providing and laying chequered tiles of approved quality of size 30 centimetres x 30 centimetres, confirming to corresponding Indian Standards for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. (Item No. 33.66)

Labour charges for removing grass, thorney shrubs, Jungli shrub, Kubabul and alike grass along roadside making the ground clean by showel and phavaras etc. complete. (Item No. 21.33)

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. (Item No. 23.01)

... (Item No. 23.01, Second Floor)

Providing expansion joints in R.Cement Concrete framed structure(interior column) with plain premoulded filler 25milimetres thick including fixing T.W. battens on both faces and finishing as directed etc. Complete. (Item No. 30.01)

Providing expansion joints in R.Cement Concrete framed structure(exterior Columns) with plain premoulded filler 25milimetres thick and 3milimetres thick alluminium plate, hold fast, fixing T.W. battens on internal face, finishing etc. complete as directed. (Item No. 30.02)

Providing expansion joints in R.Cement Concrete framed structure(at floor level) with premoulded filler 25milimetres thick and 3milimetres thick aluminium plate as required, bitumen poured filler and fixing T.W. battens on rear faces etc. complete as directed. (Item No. 30.03)

Providing expansion joints in R.Cement Concrete framed structure(at terrace level) with premoulded filler 25milimetres thick and 3milimetres thick aluminium plate as required, bituminous poured filler, fixing lead, flashing on upper side and T.W. battens on inner face finishing etc. Complete as directed. (Item No. 30.04)

Providing first class Burnt Brick masonry with conventional/Indian Standards type bricks in cement mortar 1:6 in plinth including bailing out water manually, striking joints on unexposed faces, pointing with cement mortar 1:3 on exposed face and watering etc. Complete. (Item No. 27.02, First Floor)

Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26 " height and 22" depth, supported on aluminium pipes, trolley basket made out of 5milimetres stainless steel rod fitted on telescopic channel of size 1.5 " x 20 " x 22 " on both sides of trolley of 12 " or above size, panel having 40Kilogramload bearing capacity of trolley made out of 20metresilimetres PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica, 100metresilimetres s.s. decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge) (Item No. 51.59)

... (Item No. 51.59, First Floor)

... (Item No. 51.59, Second Floor)

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index(SRI) 108(with solar reflectance & thermal emittance tested as per American Society for Testing and Materials) C 1549 and American Society for Testing and Materials C 1371 respectively, VOC less than 10 cc/g metres The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer-in-incharge. (Item No. 48.19, Third Floor)

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid(2:1) by weight covering 9 to 10 Square Metre/Kilogram with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete. (Item No. 31.09)

... (Item No. 31.09, First Floor)

... (Item No. 31.09, Second Floor)

... (Item No. 31.09)

... (Item No. 31.09, First Floor)

Providing and laying in trenches 15milimetres dai. CPolyvinyl chloride pipe including necessary excavation, fittings. Refilling trenches etc. complete Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 42.61)

... (Item No. 42.61, First Floor)

... (Item No. 42.61, Second Floor)

Providing and laying in walls/ceilings/floors 15milimetres dia. medium grade having embossed as Indian StandardsI Mark galvanised iron pipes of 1.25 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 43.01)

Providing and laying in walls/ceilings/floors 25milimetres dia. medium grade having embossed as Indian StandardsI Mark galvanised iron pipes of 2.49 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 43.03)

... (Item No. 43.03, First Floor)

... (Item No. 43.03, Second Floor)

Providing and laying in walls/ceilings/floors 32milimetres dia. medium grade having embossed as Indian StandardsI Mark galvanised iron pipes of 3.20 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 43.04)

... (Item No. 43.04, First Floor)

... (Item No. 43.04, Second Floor)

Providing and laying in walls/ceilings/floors 50metresilimetres dia. medium grade having embossed as Indian StandardsI Mark galvanised iron pipes of 5.17 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (Item No. 43.06)

... (Item No. 43.06, First Floor)

... (Item No. 43.06, Second Floor)

Providing and fixing during laying in RCement Concrete Slab rectangular 2milimetres thick Mild Steel sheet fan hook box of size 180x100metresilimetres with required depth with holes or notches as required, bottom and top sides of 1.6milimetres Mild Steel sheet fixed with 3.5milimetres dia. round headed screws together with 12milimetres dia. Mild Steel bar bent to shape with hooked ends for fan hook and painting to exposed surface (Item No. 26.68)

Providing and laying Rough Shahabad Stone Flooring 25milimetres to 30metresilimetres thick and of required width in plain/diamond pattern on a bed of 1:6 Cement Mortar including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. complete. (Item No. 33.01)

Providing and fixing 90 centimetres x 60 centimetres Granite plate engraving 10 centimetres. Height letter, figures including painting the lefters/figures with approved colour and shade complete (Item No. 44.12)

Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 600metresilimetres made out of 1.5milimetres aluminum sheet bonded with white retro reflective sheeting of Class B(Type IV High intensity micro-prismatic grade sheeting-HIngress Protection) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per Indian Roads Congress:67-2012 Table No 8.3 Supported with back support frame 25milimetres x 25milimetres x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65milimetres X 65milimetres X 6mm, 3.45m long, duly painted with with flat oil paint having alternate black and white bands of 25 centimetres width including Galvanised Iron. fixtures etc; fixing the boards in M25 grade concrete block of size 60 centimetres X 60 centimetres X 75 centimetres including transportation etc; complete. Class B(Type IV High intensity micro-prismatic grade sheeting-HIngress Protection) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.29a)

Providing and fixing of retro-reflectorised informatory sign board rectangular/Square in shape having area less than 0.9 square metre made out of 2milimetres aluminum sheet bonded with white retro reflective sheeting of Class B(Type IV High intensity micro-prismatic grade sheeting-HIngress Protection) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per Indian Roads Congress:67-2012 Table No 8.3, supported with back support frame 25milimetres x 25milimetres x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one no. mild steel angle iron post 75milimetres x 75milimetres x 6mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 centimetres x 45 centimetres x 60 centimetres, 60 centimetres below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 centimetres width including Galvanized Iron fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B(Type IV High intensity micro-prismatic grade sheeting-HIngress Protection) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.33a)

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. (Item No. 46.15)

Dismantling the R.Cement Concrete Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. (Item No. 46.29)

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. (Item No. 46.09)

Dismantling stone masonry in lime or cement mortar including stacking the materils as directed with all leads, lifts etc. (Item No. 46.11)

Conveying materials obtained from dismantling of building including all lifts, laying in layers of 20 centimetres to 30 centimetres. breaking clods for a lead of 2.00 k metres inclusive from the site of Building to the site of deposition as directed. (Item No. 2.25)

Partition :- Providing and fixing full height partitions at required location having height more than 1.34m and minimum 65milimetres thick made by using 50x50metresilimetres (finished size centrally Providence Teak Wood (CPTW) section framing at 600 milimetres center to center, covered with 6 milimetres marine ply milimeter thick requisite manufacture generally confirming to (Indian Standards 303/Indian Standards 710/-1980 ) laminate matt/ suede/ fine line finished lamanation pattern with or without grooves externally with necessary lipping (Bourmah Teak wood) moulding antitermite reatement to all plywood and wood work with ten years guarantee bond etc. including all leads and lifts etc. complete as per Architects Drawing and instruction of the Engineer in- charge. (Item No. 102.01)

Low Height Storage - Providing & fixing on site 40 centimetres Deep Low Height Storage Unit at require location less than 1.35 meter height by using 19milimetres marine ply of requisite manufacture generally confirming to Indian Standards 303/Indian Standards. 710-1980 for frame, internal verticals, horizontal divisions, openable shutters, 6milimetres thick marine ply back, with necessary locks, handles, hardware, lipping (BitumenC), moulding etc. The total shall be finished with formica laminate sheet finished lamination pattern with grooves externally and two coats of french polish with anti-termite treatemtn to plywood & wood work including all leads & lifts etc. complete, as per Architect's Drawing and instruction of Engineer in Charge. (Item No. 102.03)

Storage Full Height : Providing and fixing 53 centimetres deep Cupboard type Storage Unit made out of 19milimetres thick marine plywood of the requisite manufacture generally confirming to Indian Standards 710-1980 for frames, internal verticals horizontal divisions, shutters and 6milimetres & 12milimetres thick marine plywood for drawers with locks,handles, hardware, lipping & beading patti (BitumenC) etc. The shall be finished with veneer in approved pattern with grooves etc. and two coats of french polish and melamine polish for all BitumenC moulding & lipping patties with antitermite treatment to plywood & wood work with ten years guarantee on requisite stamp paper including all leads & lifts etc. complete as per drawing and instruction of Engineer- in-charge etc. complete. (Item No. 102.04)

3 Seater Sofa : Providing & Supplying Three seater sofa of overall size 1950x760x825 milimetres ht. made out of 75x38milimetres (finished size ) with Cement ConcreteTW section frame 6milimetres marine plywood generally confirming to Indian Standards303/Indian Standards 710-1980 for necessary covering from back & arm rests. The seat shall be 100metresilimetres thick branded quality foam covered 1" soft foam and arms having Cement ConcreteTW 50metresilimetres thick 50 density branded foam covered 1" plain soft foa metres All work covered with tapestry fabric upto Rs.400/- per SquareM.including necessary hardware, naver, jute cloth.Casement, springs or belted absorber etc. complete. All exposed wooden surface shall be melamine polished and antitermite treatment to plywood and wood work with five years guarantee bond etc. including all leads & lifts etc. complete as per Architect's Drawing & instruction of Engineer-in-charge. (Item No. 102.08)

2 Seater Sofa : Providing & Supplying two seater sofa of overall size 1350x760x825 milimetres ht. made out of 75x38milimetres (finished size ) with Cement ConcreteTW section frame 6milimetres commercial plywood generally confirming to Indian Standards303/Indian Standards 710-1980 for necessary covering from back &arm rests. The seat shall be 100metresilimetres thick Dunlop or MM or equivalent brand quality foam covered 1" soft foam and arms having Cement ConcreteTW 50metresilimetres thick 50 density branded foam covered 1" plain soft foa metres All work covered with tapestry fabric upto Rs.400/- per SquareM.including necessary hardware, naver, jute cloth.Casement, springs or belted absorber etc. complete. All exposed wooden surface shall be melamine polished and antitermite treatment to plywood and wood work with five years guarantee bond etc. including all leads & lifts etc. complete as per Architect's Drawing & instruction of Engineer-in- charge. (Item No. 102.09)

3 Seater Bench : -Providing and supplying on site stainless steel three seater bench Model No NKD 306 strong seat and back 1.5milimetres thick unch pressing, angular connection between benchs with 1.8milimetres bonical beam with end to end attached aram (1.2milimetres thick withpunch pressing welding ) with stainless coating size 900(H) x 680(W)x 1750(L) etc complete (Item No. 102.10)

Staff Revolving Chair : Providing Visitor Chairs having a medium back with head rest, with a synchronized tilting mechanism with Multiple locking systems, ABritish Standard for seat, with swivel & depth. The chair shall have adjustable arm pad & option of Polyvinyl chloride padding. The seat shall have a gas lift for height adjustment and the chair shall have a Nylon base with castors. (Item No. 102.37)

Providing and fixing on site notice board made out of 6 milimetres marine ply of the requisite manufacture generally confirming to Indian Standards310/Indian Standards710-1980 backing and 12 milimetres thick soft board covered with tapestry/up to Rs. 200 per meter including necessary lipping (BitumenC), moulding, hardware, polishing etc. and Anti- termite treatment to plywood and woodwork with ten years guarantee bond etc. including all leads & lifts etc. complete as per Architect Drawing and instructions of Engineer in Charge. (Item No. 102.12)

Providing and supplying Cement ConcreteTW stool of size 0.45x0.45 mtr. of height 0.75 with using Cement ConcreteTW frame work and top of 25 milimetres thick, as per approved typical drawing with french polishing and finishing etc complete (Item No. 102.26)

Supplying glass table top 8 milimetres thick in required size and shape including finishing the all side edges machnically smoothly etc. complete. (Item No. 102.16)

Tables (1.20X0.60) : Providing & fixing in position table for the Clerical Staff having overall size of 120x60x76 centimetres height made out of 19milimetres thick Marine Ply of the requisite manufacture generally confirming to Indian Standards303/Indian Standards710-1980 top, vertical side & 6milimetres marine plywood of requisite manufacture generally confirming to sides and 6milimetres marine ply bottom with necessary sliders one open shelf of 19milimetres thick marine ply with necessary lipping on external sides and foot rest out of 40x75 milimetres (finished dimension) CPTW etc. as per drawing and instructions. the external side and top shall be finished with 1milimetres thick laminate matt/suede/fine line finished lamination pattern with grooves all internal surfaces on table and drawer shall be internally finished with two coats of french polish with antitermite treatment. (Item No. 102.31)

Providing & Fixing Steel cupboard of size 740metresm(H) x 486milimetres (W)x 546mm(D), weight 185 Kilogram & volume 66 lit.(Material supplied should be of approved manufacturer. (Item No. 102.23)

Conference Table @ 3600Lx1400Dx750HT Providing & Fixing of Main Table @ 3600Lx1400Dx750HT-made up of 18+18milimetres Thick MDF top with Polyvinyl chloride Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4milimetres thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in Polyvinyl chloride Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring., MODESTY PANEL:-to be made of 18milimetres thick Prelaminated particle board with Polyvinyl chloride edge band Access Flap:-For Wire manager 2 Nos. (Item No. 51.31)

High back Chair: Providing and supplying center pivot, revolving, High back chair Depth-45 centimetres, width- 50 centimetres, height-121 centimetres to 131 centimetres & seat height-45 centimetres to 55 centimetres. (+/- 2 centimetres) with five legged metal /moulded nylon base with push back arrangement. Chairs shall have high density moulded ,360 revolving on suitable base, gas lift , heavy duty twin wheel castors to take min 80 kilogram/castor with two - pneumatic height adjustment one piece moulded type polypropylene armrest. The chair shall be provided with approved tapestry upto Rs 300/m with necessary beading wherever required. All metal work shall be Epoxy Polyster Powder Coated. (Item No. 102.35)

Mid back Chair: Providing and supplying center pivot, revolving, Mid back chair Depth-45 centimetres, width-50 centimetres, height-105 centimetres to 115 centimetres & seat height-45 centimetres to 55 centimetres. (+/- 2 centimetres ) with five legged metal /moulded nylon base with push back arrangement. Chairs shall have high density moulded ,360 revolving on suitable base, gas lift , heavy duty twin wheel castors to take min 80 kilogram/castor with two - pneumatic height adjustment one piece moulded type polypropylene armrest. The chair shall be provided with approved tapestry upto Rs 300/m with necessary beading wherever required. All metal work shall be Epoxy Polyster Powder Coated. (Item No. 102.36)

Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure:-The legs are made of Square tube of size 25 x 25milimetres made out of MS with a thickness of 1.2 milimetres The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2milimetres thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25milimetres made out of MS with a thickness of 1.2 milimetres The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25milimetres made out of MS with a thickness of 1.2 milimetres All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.Side Panel:-The side panels are made up of 18milimetres thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2milimetres thick Polyvinyl chloride edge Banding. The overall width of the side panel is 150 milimetres The side panels have 18milimetres thick prelam particle board Baton running for required length to add rigidity to the structure. Head Board :-The head board is made up of 18milimetres thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2milimetres thick Polyvinyl chloride edge Banding. The head board size to be considered as 1000 x 650 milimetres Foot Board :-The foot board is made up of 18milimetres thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2milimetres thick Polyvinyl chloride edge Banding. The head board size to be considered as 1000 x 450 milimetres Bed Base:-The Bed Base is made up of 12milimetres thick Prelam Particle Board with both side White laminate. (Item No. 51.55)

Excavation for foundation in earth, soils of all types, sand, gravel, soft murum including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete.(By Mechanical Means) a) Upto 1.50metres lift Normal Rate b) 1.50metres to 3.00metres lift, Add 10% c) 3.00metres to 4.50metres lift, Add 20% d) 4.50metres to 6.0metres lift, Add 30% (Item No. 12.03)

Providing dry/trap/granite/quartzite/gneiss rubble stone soling 15 centimetres to 20 centimetres thick including hand packing and compacting etc. complete. (Item No. 21.38)

Providing and laying in situ/ready mix cement concrete of M-10 proportion with trap/granite/quartzite/gneiss metal in foundation including necessary form work, compacting and curing etc. complete.(with reversible drum type mixer without Supervisory Control and Data Acquisition with fine agreegates of required specifications(Natural sand/Vertical Shaft Impactor sand finely washed etc) (Item No. 11.02)

Providing and laying in situ/Ready Mix cement concrete M-20 of trap/granite/quartzite/gneiss metal for R.Cement Concrete work in foundations like raft, strip foundations, grillage and footings of R.Cement Concrete columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided(Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based Programmable Logic Controller without Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 25.11)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/granite/quartzite/gneiss metal for R.Cement Concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller without Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand Vertical Shaft Impactor Grade) (Item No. 25.50)

Providing, cutting, bending, hooking, tying and laying in position T Metric Tonnes FE 500 steel bars for reinforcement for all RCement Concrete works as per detailed drawings etc. complete. (Item No. 14.01)

Providing second class Burnt Brick masonry with conventional/Indian Standards type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete (Item No. 27.05)

Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15milimetres thick in Cement Mortar 1:4 and rough cast treatment 12milimetres thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete. (Item No. 32.12)

Providing and applying white-wash in one coat on old/new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete. (Item No. 36.02)

Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in one coat including scaffolding, preparing the surfaces.(excluding the primer coat.)etc. complete. (Item No. 36.10)

Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 Kilogra metres to 20 Kilogra metres Per Square metres.) Spec.number: As directed by Engineer-in-charge. (Item No. 23.09)

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metres and spreading for embankment or stacking as directed. (Item No. 2.11)

Providing and laying in situ/ready mix/ready mix M10 cement concrete of trap/granite/quartzite/gneiss metal in foundation including necessary centering, formwork, bailing out water, compacting and curing etc. complete.(with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled with reversible drum type mixer/concrete batch mix plant(pan mixer) with natural/artifical sand) (Item No. 12.25)

Providing and laying in situ cement concrete M20 with tremix treatment for 100metresilimetres thickness for flooring with groove cutting of 4milimetres wide and 20metresilimetres deep with necessary refilling with bitumen etc. complete. (Item No. 33.30)

Drilling of 150 milimetres dia Borewell with all charges etc complete

Providing and fixing 180 milimetres dia U.Polyvinyl chloride casing pipe as per Indian Standards 12818-1992 outer dia should be 165.4 milimetres etec complete

Providing and fixing 180 milimetres dia U.Polyvinyl chloride cap etc complete

B R Bhadane