SPECIAL REPAIR TO BLDG NO T-142 (MAIN OFFICE) OF KUMAON AT 4TH INF LINE MORAR CANTT UNDER GE GWALIOR

Amount

Demolition of cement concrete (unreinforced in roofs, floors (other than ground floors), beams, stair cases, landing, chajja and smiliar suspended work complete all as specified and directed.

M&L 15mm thick rendering in CM(1:4) on faces of bricks work on concrete surfaces with WPC, finished even and smooth without using extra cement as in roof (WPC shall be measured and paid seperately) complete all as specified and directed

Supply only water proofing compound complete all as specified and directed

M&L water proofing treatment to roof slab and vertical surface with APP modified membrane weight not less than 3.00kg/Sqm and thickness of membrance not less than 3mm reinforcement with polyster non wooven fabric (wt not less than 160gm/Sqm) water absorption not more than 1% on mass within 24hrs and water tightness/impermeability at 2 kgs/cm2 laid on primed surface with torch application method as per manufeture :- (a) Applying evenly a coat of bitumen primer conferming to IS3384-1965@3kg/Sqm. (b) Laying APP modified plymeric membrane with 100mm overlap in logitudinal direction and 10mm in transverse direction all joints and changes in all directions should be curved with centre mortar (1:3) mixed with SBR complete all as specified and directed.

Taking down existing tarfelt from roof and remove from site complete all as specified and directed

M&L roughening surfaces of old concrete roof by picking, sweeping clean and sashing down with water to remove dust etc and applying a coat of cement slurry @ 3kg per Sqm complete all as specified and directed

M&L for providing, cement concrete type B0 1:2:4, (using 12.5mm graded stone aggregate) in roof kerbs/coping bed block or mud stops, rounded or chamfered on edges complete all as specified and directed

Dismantling floor, hearth or wall tiling, stone slabs, cooking plateform slabs including cement moratr bedding (but not backing), removing serviceable tiles to store and rubbish off the permisses complete all as specified and as directed

Demolition of cement concrete (unreinforced) as in any floor and paving n.exc 15cm thickness (below or above GL) incl the disposal upto 50M complete all as specified and directed.

M&L 25mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) as in levelling course at any floor/roof surface complete all as specified and directed.

M&L 20mm thick screed bed or bedding layer of mortar in cement mortar 1:6 for laying floor finishes complete all as specified as directed.

M&L 20 to 25mm thick machine cut kota stone flooring and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing as in floor and stair case complete all as specified and directed.

Taking down cement or cement lime plaster incl wall tiles, any description on brick stone and concrete surface walls including chhajja of any floor and roof projection etc incl raking out joints hacking for key scrubbing down with water etc complete all as specified and directed

M&L 15mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished fair and smooth complete all as specified and directed

M&L 10mm thick rendering in cement mortar 1:4 on faces of brick work or concrete surfaces as in back of tiles kota complete all as specified and directed.

M&L 20 to 25mm thick machine cut kota stone as in skiriting dado riser of steps and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L Glazed ceramic coloured tiles 300mm x 200mm x 5 mm to 7 mm thick, in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles complete all as specified and directed

M & L 15mm thick screed bed or bedding layer of mortar in cement mortar 1: 6 for laying floor finishes complete all as specified and directed

M&L for 9-10 mm thick vitrified tiling in floors etc set, jointed in neat cement slurry & pointed in coloured cement to match the shade complete all as specified and directed

M&L coloured non skid ceramic tile 7 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed

M&L 20mm thick grainte slab of any shade as approved by GE as in kitchen platform bedded and jointed with grey cement slurry and jointed with white cement with admixure of pigment to match the shade of granite stone including complete all as specified and directed

M&L 60mm thick M-35 Grade machine pressed precast conctete interlocking paver block with grey cement and no pigment any shape and size conforming to IS 15658-2006 laid dry over 50mm thick sand cushion complete all as specified and as directed

M&L 75mm thick PCC 1:3:6 type C2 (using 20mm graded stone aggregate) finished even and smooth without using extra cement as in plinth protection including forming of joints 10mm wide and 75mm deep and joint filled with bitumin and sand mixture in 1:1 ratio complete all as specified and directed.

S&F in repair PVC (SWR) floor trap plain with grating including jointing with solvent cement and fixed in repair to 75mm dia outlet pipe complete all as specified and directed

M&L 1st quality vitreous china squatting pan, orissa pattern size 580 x 440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete lived in repairs and making good to floor complete all as specified and directed.

S&F in repairs of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor complete all as specified and directed.

S&F 1st quality vitreous china wash hand basin, white flat/angle back, size 550 x 400mm complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size complete all as specified and directed.

S&F 1st quality Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specefied and directed.

Supply only brass chromium plated waste fitting of wash basin and sink with inlet and outlet screwed for pipe or connections and with one cleaning cap 32mm bore complete all as specified and directed

Supply only pillar tap 15 mm dia cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot or Cold complete all as specified and directed

S&F in repair Swivel shower of chromium plated of size 65 to 90 mm for fixing with 15mm bore pipe complete all as specified and directed

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass 60 cm long and 12 cm wide with CP bracket guard and railing 60cm long complete all as specified and directed by the Engineer-in-Charge.

S&F PVC Grating Square 150mm with hinge (openable) complete all as specified and directed

S&F magic door eye stainless steel complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified as directed

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified as directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified as directed

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified as directed

S&F 110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal, provided with access door, complete all as specified as directed

S&F 110mm bore PVC (SWR) bend complete all as specified as directed

S&F 75mm bore PVC (SWR) bend complete all as specified as directed

S&F 110mm bore PVC (SWR) junction single (single T), equal or unequal, provided with access door complete all as specified as directed

S&F 75mm bore, PVC (SWR) junction single (single T), equal or unequal, provided with access door complete all as specified as directed

S&F 110mm bore PVC (SWR) vent cowl complete all as specified as directed

S&F in repair 20mm bore ball vavle high pressure of PTMT with epoxy coated aluminium road and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed

S&F in repair 20mm bore gun metal globe/ gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed

Taking up and down 15mm bore steel tubing and connections including cleaning for refixing or remove to store complete all as specified as directed

Taking up and down 20mm bore steel tubing and connections including cleaning for refixing or remove to store complete all as specified as directed

M&L cutting chases, in brick walls pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc complete all as specified and directed

S&F 15mm bore tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed .

S&F 20mm bore tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed .

Refixing old 15mm bore steel tubing and connections in new or old positions (walls, ceiling, floor etc) complete all as specified and directed

Refixing old 20mm bore steel tubing and connections in new or old positions (walls, ceiling, floor etc) complete all as specified and directed

Disconnecting existing water tanks setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position capacity of tank exceeding 250 ltr and not exceeding 500 ltr complete all as specified and as directed .

Dismantling of water tanks exceeding 250 ltr and not exceeding 500 ltr capacity and removing from site complete all as specified and as directed

S&F 500 ltr capacity rotational moulded polytheline triple layer water storage tank (cylindrical vertical with close top) hoisted and fixed in position complete all as specified and directed

S&F Gun metal globe or Gate valves with iron wheel head screwed both ends for iron pipe of 20mm bore or brass ferrule complete all as specified and directed

S&F Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe of 20mm bore of brass ferrule complete all as specified and directed

S&F in repair 15mm dia brass bib cock cast copper alloy with butterfly handle screwed down screwed for iron pipe or for brass ferule complete all as specified and directed

S&F in repairs PVC connections 15mm dia for was hand basin and low level flushing cistern of 450mm length PTMT nuts at ends to connect pipe or sanitary fitting complete all as specified and directed

S&F in repair 15mm bore stop valve copper alloy screwed down high pressure with CAPSTON HEAD handle chromium plated concealed type screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair 15mm bore stop valve copper alloy screwed down high pressure with CAPSTON HEAD handle chromium plated angular type screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

M&L cutting holes into or through brick walls built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required; superficial area not exceeding 150 Sqcm complete all as specified and directed

M&L LDPE pipes of pressure rating 6kg/cm square fixed complete incl all fittings to wall and ceilings or in floors of 32 mm bore complete all as specified and directed

Taking down shutters of any description not exceeding 1 sqm each and removing from the site complete all specified and directed

Taking down shutters of any description in exceeding 1 sqm and not exceeding 2 sqm each and removing from the site complete all specified and directed

Taking down chowkats or frame of any description with shutters (without taking off shutter from the frame) not exceeding 1.5 Sqm each and removing from the site incl cutting holes for holdfasts incl making good in CM 1:3/PCC 1:2:4 type B0 complete all as specified and directed

Taking down chowkats or farame of any description with shutters (without taking off shutter from the frame) exceeding 1.5 sqm and not exceeding 4 sqm each and removing from the site including cutting holes for holdfasts including making good in CM 1:3/PCC 1:2:4 type B0 complete all as specified and directed

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube suppling & fixing in opening as per spefication & drawing but single side prelaminated PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelaminated sheet complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement suppling & fixing in the frame at site as per specified & drawing but single side prelaminated PVC sheet used instead of Plain colour PVC sheet and stile & rails aving one side feathered edge and on other side 10mm 900 bent edge complete all as specified and directed.

S&F 2nd class HW plain, solid straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F Plain fillets of second class hard wood, square or rectangular in section, clean sawn, secured with nails or brads; sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm complete all as specified and directed.

S&F 35mm thick factory made plain, framed, panelled shutter (two panel) with lock rail and 12mm thick veneered particle board with commerical veneering on both faces the size of rail and stile as per IS-1003 (Part-I) Kiln seasoned and chemical pressure treated complete all as specified and directed.

S&F 35mm thick factory made glazed and skelton shutters 2nd class HW open rebated and prepared to receive gauage (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred bead for security glass etc size of members of shutters as specified in IS-1003 supplied and fitted to chowkhats complete all as specified and directed.

S&F 30mm thick factory made glazed and skelton shutters 2nd class HW open rebated and prepared to receive gauage (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred bead for security guages. Size of frames as specified in CI-8.23(b) of SSR Part-I complete all as specified and directed

Supply only galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tineed tacks or galvanised wire staples incl a coat of french blue paint complete all as specified and directed

Supply only 3mm thick figured glass pin head type in square not exceeding 0.5 sqm each pane in new glazed shutter complete all as specified and directed

Supply only sheet glass 3 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed

S&F 25mm thick block board of grade 2 quality and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed

S&F in repair aluminium anodised barreld tower bolts of extruded section 150mm long complete all as specified and directed

S&F in repair 150mm long extruded aluminium alloy handles fabricated type complete all as specifed and directed

S&F 200mm long mild steel barrel tower bolts stove enamelled black with bright bolt complete all as specified and directed

S&F 100mm long mild steel barrel tower bolts stove enamelled black with bright bolt complete all as specified and directed

S&F mild steel sliding door bolts plate type stove enamelled black with bright bolts not less than 12mm dia with and incl a minimum of 6 bolts plate and nuts four on bolts and two on staple plate in wooden shutters and welded diveresed in steel shutter 300mm long complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed

S&F Butt hinges, medium weight, cold rolled mild steel, 75 mm size complete all as specified and directed

S&F Butt hinges, medium weight, cold rolled mild steel, 50 mm size complete all as specified and directed

S&F small fitting such as doors & window cleats/stoppersand the like incl all necessary labours articles n exc 200cum each in 2nd class hard wood complete all as specified and directed.

S&F 150mm size mild steel pressed handle over type stove enamelled black complete as specified and directed

S&F 100mm size mild steel pressed handle over type stove enamelled black complete as specified and directed

M&L mild steel hold fasts clamps or similar small articles confirming to Fe 410 or Fe 310-0 complete all as specified and directed

S&L Framed work such as grills, gratings, etc and similiar works conforming to Fe 410-0 complete all as specified and directed

Fixing only old mild steel frame work such as grills grating etc and smililar woks complete all as specified and directed

Supply only galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tineed tacks or galvanised wire staples incl a coat of french blue paint complete all as specified and directed

Hacking out old broken glass (any thickness site quality or description) from wooden frame or stone concrete and brick surrounds glazed with putty or fixed with beads complete all as specified and directed

S&F sheet glass 3 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pan complete all as specified and directed

S&F sheet glass 3 mm thick pin headed type and glazing with oil putty in square not exceeding 0.5 sqm in each pan complete all as specified and directed

M&L preparation or new steel and iron surfaces of any description and applying two coats of sythentic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation old painted steel and iron surfaces exceeding 10 cm in width or girth and applying one coat of sythentic enamel paint complete all as specified and directed.

M&L Preparation of new surfaces of wood and wood based materials of any description and treated with tar or coal tar black paint to back of chowkhats etc area exceeding 0.10sqm and not exceeding 0.50 sqm each complete all as specified and directed

M&L preparation of newly plastered or completely removed surfaces of wall and applying two coats of distemper oil emulsion, white or tinted and including applying of Birla white wall care putty @ 1.2 kg/sqm complete all as specified and as directed.

M&L surface excavation in any type of soil not exc 30 cm deep and average 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

M&L hard core of broken stone of gauge not exc 63mm deposited spread and levelled in layers not exc 15cm thick watered and rammed to a true surface complete all as specified and as directed.

M&L preparation of newly plastered or completely removed surfaces of wall and applying two coats of Apex paint over a coat of primer appproved colour complete all as specified and directed

S&F 20mm bore tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed .

M&L preparation of old wood surfaces of any description and applying one coats of synthetic enamel paint complete all as specified and directed

M&L preparation of new wood surfaces of any description and applying two coats of synthetic enamel paint over pink primer complete all as specified and directed

M&L complete removal of existing treatment of wall complete all as specified and directed

M&L preperation of new/old plastered or unplastered surfaces of walls (completely removed surfaces) and applying two coats of wether proof water based emulsion paint (Acrylic paint exterior grade) over a coat of Acrylic primer and including filling depression by Birla wall care putty etc complete all as specified and directed.

M&L preparation of wall surface and applying one coats of exterior weather emulsion paint of shade approved by Engr-in-Charge in isolated width complete all specified and directed

M&L preparing new/old surfaces of walls by washing / rubbing down and stopping distempering surface and applying two coat of distemper oil emulsion white or tinted over a coat of primer complete all as specified and directed

M&L preparation of newly plastered ceiling surface and applying three coats of white wash complete all as specified and directed

M&L applying one coat of white wash including preparation of old ceiling surface complete all as specified and directed

S&F chicken wire mesh with tack screws of galvanised mild steel wire cloth of 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all complete all as specified and directed

M&L fixing of precast RCC bond stone 50mm thick in brick /stone walls complete all as specified and directed. Note : Reinforcement shall be measaured and paid in separate item.

M&L for TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hoping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item item No 118 above but 5 mm to 8mm dia as in stirrups, spacers and binders etc complete all as specified and directed.

M&L for applying treatment on exposed roof portion incl beams , chajjas , slab etc as under complete all as specified and directed :- (a) Removing all loose concrete elements & applying acid wash & applying cement slurry mixed with Nitobond / tapcrete/pidigrete complete all as specified and directed (b) Inserting drilling holes in the wall /beam by 10 mm dia bars & tuck welding with existing reinforcement @ 0.50 m c/c, nailing wire fabric 50 x 50 mm in the complete all as specified and directed. (c) M&L 15 mm dubbing coat in CM (1:2) mortar mixed with Nitobond /Tapcrete /Pidigrete@ 2 % by weight complete all as specified and directed.

M&L superlatex waterproofing chemical or equivalent approved make in white cement complete all as specified and as per manufacturers instructions filling in V groove in walls /floors.

Demolition of Brick or stone boulder Masonry built in cement mortar complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete.all as specified and directed.

M&L for Powder coated (minimum thickness of powder coating 50 mm micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

M&L for Powder coated (minimum thickness of powder coating 50 mm micron) aluminium door shutters of aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing, powder coated aluminium handles 150mm size 2 Nos, 3 Nos powder coated aluminium hinges heavy duty and 02 Nos 150mm long powder coated aluminium tower bolts in each door shutter with powder coated aluminum snap beading, screws etc complete all as specified and directed. Note : Panel filling i.e glass, fibre sheet, board etc. shall be measure and paid separately.

M&L for powder coated (minimum thickness of powder coating 50 mm micron) aluminium sliding window (two track) with aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware i.e handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc complete all as specified and directed. Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc shall be measured and paid separately.

M&L for powder coated (minimum thickness of powder coating 50 mm micron) aluminium sliding window (three track) with aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware i.e handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc complete all as specified and directed. Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc shall be measured and paid separately.

S&F for powder coated aluminium Decco grill with 10 mm dia and 75 mm mesh size of design and pattern as approved by Engr-in-Charge complete all as specified and directed.

S&F butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type C-11, 100mm long complete all as specified and directed

S&F butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type C-11, 75 mm long complete all as specified and directed

S&F 100 mm long aluminum anodized barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F extruded aluminum alloy handles 100 mm size fabricated type anodized all as specified complete all as specified and directed

S&F Hasp & Staple aluminium anodised size 100 mm including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Hasp & Staple aluminium anodised size 75 mm including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 300 mm aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips, cast or extruded sections or cast aluminium alloy complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm (weight not less than 600 gms/per sqm) and fixed with aluminium wire staples, wooden beads etc complete all as specified and directed.

S&F for door closer hydraulically regulated, designation No 3, universal type, aluminium die-cast body (ISI Marked) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed.

S&F gate and shutter hooks and eyes aluminium plate type II of 75mm size complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue ,anodised with hard drawn steel spring,150mm long, fixed in floor complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators,sockets,light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

Taking down main switches/MCB DBs of any capacity/type including MCBs complete all as specified and directed.

Taking down and servicing/greasing/painting of ceiling fan/ exhaust fan of any size and refixing in position including provision 3 core flexible PVC insulated multi stranded copper conductor of size 0.5 Sqmm from ceiling rose/ connector to fan with replacement of capacitor complete all as specified and directed.

M&L for point wiring with 1.5 sqmm (Nominal Area) PVC insulated FRLS un sheathed multi stranded copper conductor drawn in and including non metalic rigid PVC concealed conduit of heavy grade not less than 20 mm size with all fitings and accessories including factory made MS/ pressed steel terminal modular flush box with zinc coated duly concealed in wall including reqd as per site reqmt for mounting modular switches, sockets fan regulators etc including continuous earth wire PVC insulated 1.5 Sq mm FRLS copper conductor connecting to common earth and earth dolly complete all as specified and directed :- Make of wire : Finolex, Plaza, Polycab. Make of conduit : Anchor, Modi, Presfit.

For one light/fan point controlled by one switch

For one 5 pin socket out let 5 amps on same board.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

Description all as per item No 146 here in before but point wiring with 2.5 sqmm FRLS multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 1.5 sqmm FRLS PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed . Make of wire : Finolex, Plaza, Polycab. Make of conduit : Anchor, Modi, Presfit.

S&F ceiling rose surface bakelite 3 terminals 65x50mm complete all as specified. Make : Anchor/Cona/Legrand.

S & F modular white cover plate with frame of 06/08/12 module. Make : Anchor/Cona/Legrand.

S & F modular white cover plate with frame of 04 module. Make : Anchor/Cona/Legrand.

S & F modular white cover plate with frame of 03 module. Make : Anchor/Cona/Legrand.

S&F Modular switch 1 way 06 amp single pole. Make : Anchor/Cona/Legrand.

S & F modular switch socket combination 16A, 6 Pin of 3 module. Make : Anchor/Cona/Legrand.

S & F of modular socket outlet 6A-5 pin combined of 02 module. Make : Anchor/Cona/Legrand.

S & F of modular fan step regulator 120 W-2 module. Make : Anchor/Cona/Legrand.

S&F Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings incl LED Bulb 12W/14W complete all as specified and directed. Make of Lamp Holder : Anchor/Cona/Legrand. Make of LED Bulb : Philips, Wipro, Havells.

S&F Ultra bright LED Tubelight with suitale for Regal Batten for LED Tube of 22w incluing required length of 1.5 Sqmm PVC multistranded copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. Make : Halonix/Havells/Wipro.

S&F of 20W of LED security Light fixture with IP66 protected Die-Cast Aluminum housing and heat resistive toughened glass. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60V DC. Make : Wipro/Halonix/Havells.

S&F recessed/surface LED ceiling tile of 36 Watt with broad collar frame offering superb energy saving suitable for 600 x 600mm ceiling complete all as specified and directed. Make : Crompton / Philips / Havells.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated unsheathed FRLS multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLS copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. Make of wire : Finolex, Plaza, Polycab Make of conduit : Anchor, Modi, Presfit.

Supply, install, commissioning and installation of distribution box indoor type, factory made out of CRCA sheet 2mm thick with angle iron 30x30x2 mm complete with inside, outside powder coated with suitable size copper single/ two core wire for each control, cable gland, with 100 Amp rated TPN copper busbar (for outgoing) duly insulated (including self insulated) maintaining proper space for each busbar and grouting panel in wall etc and making good the disturbed surface complete including with arrangement and including taking down the existing TPN DB/metal/PVC box comprising for following fittings complete all as specified and directed. :- (a) MCCB TPN, 100 Amps ,16 KA - 01 No (For incoming) (b) Amp Meter (0-100 Amp) - 01 Nos (c) Volts Meter (0-500 Volts ) - 01 No (d) Indicator Lamp set of three R,Y,B - 01 Set (e) ASS & VSS with CTs - 02 Nos (01 Each) (f) MCB SP 63 Amps, 230 volts - 10 Nos (For outgoing) (g) Nutral bus bar link mounted on insulator.

S&F in repair, MCB DB, sheet metal enclosures double door SPN 12 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed. Make : Legrand/Siemens/Scheider

S&F MCB SPN 40 to 63 Amps, 240 volts 'B' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed. Make : Legrand/Siemens/Scheider

S&F MCB SP 240 volts, 6 to 32 Amps, 'B' series 10 KA including connection with suitable size copper lugs complete all as specified and directed. Make : Legrand/Siemens/Scheider

S&F sheet metal earth plug, socket, single pole and neutral with single pole MCB 20. Amps 240 volts in repairs complete all as specified and directed. Make : C&S, MDS, Schneider

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable (Heavy duty) with aluminium conductor 1100 volts grade, cross sectional area size 35 Sqmm 4 Core. Make of cable : Finolex, Polycab, Gloster.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level not exc 1.5m above the starting point complete.

M&L High density polyethylene pipes (HDPE) 50mm dia of pressure rating 6 kgf/cm2 laid in trenches complete all as specified and directed.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Sch (Part-I) connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe of required length etc complete all as specified and directed.

M.S. ENGINEERS

M/S ISLAM AND BROTHERS

RAJ AND BROTHERS

Babatia super works

M/S YOGANSH CONSTRUCTION CO.

M/s Shri Diwakar Singh

GURU KIRTH BUILDERS

M/s Kohli Builders