REPAIRS TO FLOORING, PLASTERING, PLUMBING, FALSE CEILING, SANITARY FITTINGS, ROOF, WALLS, CERTAIN JOINERY WORKS OF CERTAIN BLDGS AND REPAIRS TO RETAINING WALL, SHOTCRETING, BOULDER PITCHING AND KERB STONE AT 2U DET AREA UNDER GE (S) DIGLIPUR

Amount

Taking down cement plaster and the like on brick or stone wall and concrete surfaces including racking out joints, hacking for keys, scrubbing down with water etc, complete all as specified.

M&L rendering 15 mm thick on brick & concrete surface in CM 1:4 mixed with integral water proofing compound @ 3% by weight of cement finished even and smooth without using extra cement complete all as specified and as directed. (Note: Water proofing compund shall be measured and paid seperately)

Supply of integral water proofing compound

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6, including finishing even and smooth without using extra cement complete all as specified.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base paint over a coat of white wash complete all as specified and directed

M&L for applying two coats of distemper oil emulsion on new wall surfaces and including treating with 3mm thick wall care putty and a coat of primer, white or tinted complete all as specified and directed

M&L for preparation of newly plastered surface of wall and applying three coat of white wash complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar complete all as specified and directed.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1: 6 complete all as specified and as directed.

Demolition of cement concrete not exc. 15cm thick below or above ground level and removing the debris to a distance not exc 50m from site all as directed

M&L for 75mm thick cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as Sub base of flooring complete all as specified and directed.

M& L for 40mm thick PCC flooring type B1 (1:2:4) (using 20 mm graded stone aggregate) including surface finished even and smooth with using extra cement complete all as specified and directed.

M & L 75mm thick PCC type C2 1:3:6 (40mm garade aggregate) as in plinth protection complete all as specified and directed by Engr-in-Charge

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not packing) removing of servicable tiles to store and rubbish off the premises complete all as specified.

M&L non - skid ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified

M&L glazed coloured ceramic tiles in vertical surface 300 x 200 x 7 mm thick set and jointed in neat cement slurry and pointed in colour cement to match and 10 mm thick rendering in cement mortar 1:4 complete all as specified.

M&L non -skid Ceramic coloured tiles (300x300mm) x 6-7 mm thick matt finish in floors set & jointed in neat cement slurry and pointed in cloured cement to match laid over 15 mm in CM 1:6 complete all as specified

M & L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floor/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match (light shade) including Screed bed or bedding layer of mortar 15 mm thick CM 1:6 for laying floor/wall finishes complete all as specified and directed

Dismantling of framed work in fillets, rails, posts, rafters, purlins, etc 40sq.cm in section

S&F for hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as specified and directed.

M&L for preparation of steel surface of any description over 10 cm in width or grith and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and directed.

Dismantling of AC/CGI sheet (corrugated, semicorrugated) any size and thickness complete all as specified

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to waal, fixed with self tapping screws and including removal of old sheets etc, all as specified and directed by Engr-in-Charge.

S&F plain galvanised, mild steel sheeting of 0.63mm thick, in rideg, hips, valeey gutters, drip and straight flashing (lingth and girth as fixed) with grade of zinc coating 275 as in repair complete all as specified and directed

Supply, Providing and fixing suspended false ceiling consisiting of 6mm thick asbestas cement plain building board suspended on Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat andsteel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. fixed to roof slabs, Boards are to be joined and finished so as to have a flush look which includes finishing the tapered and square edges of the board and two coat plasting emulsion paint over one coats of primer & one layer putty 3mm thick suitable for board. (As per the recommendations/ practice) including necessary scaf folding and shuttering complete all as specified and directed by Engr-in-Charge.

Dismantling of timber boarding any description fixed in any position with nails/screws complete all as specified & directed

S & F in repairs, vitreous china Squatting pan Orissa pattern of size 580mx440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including concrete bedding complete, all as specified and directed.

S&F in repairs Vitreous China , semi-pedestal pattern (Anglo-Indian Type) complete including provision of lime concrete bedding complete all as specified and directed

S&F in repairs wash hand basin vitreous china white flat back of size 580 X 450mm with brackets,including CP pillar tap of 15mm bore complete all as specified and as directed .

S & F in repair vitreous china bowl urinal flat back size of 465 x 355 x 265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern & flush pipe) but exncluding waste pipe, complete including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with screws, pointing around urinal back in cement complete all as specified and directed.

S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete

S & F in repair PVC valveless syphonic action type low level flushing cistern 10 Ltr capacity with inlet, ball valve, float and handle incl brackets and flush pipe of polyethylene of low or high density or PVC. 32 mm dia all as specified and directed

S&F in repairs PVC connections 15mm size with PTMT nuts and washers for 600mm long pipe complete all as specified and directed.

S&F in repairs health faucet fixing in pipes etc complete all as specified and directed.

S&F in repairs 15mm bore stop valves cast copper alloy screwed down high presure screwed at the ends for iron pipe or union with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 125mm size brass chromium plated shower rose with swivel joint fixing to GI pipe of 15mm dia complete all as specified and directed.

S&F in repairs 15mm bore bib taps chromium plated cast copper alloy of fancy type screwed down for iron pipe complete all as specified and directed. .

S&F in repairs 15mm bore CP pillar tap cast copper alloy fancy type screwed down high pressure, with long screwed shank and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and dierected

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of 500 ltr capacity including provision of inlet, outlet overflow and wash out connections and taking down the unserviceable tank and removing to store complete all as specified and as directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of 1000 ltr capacity including provision of inlet, outlet overflow and wash out connections and taking down the unserviceable tank and removing to store complete all as specified and as directed.

Taking down shutters of any descrption not exceeding 1.0 sqm each from chowkhats complete all as specified.

Taking down shutters of any description, exceeding 1.0 sqm but not exceeding 2.0 sqm each, from chowkhats complete all as specified.

Taking down chowkats or frames not exceeding 1.5 Sqm each but with shutters (without taking off shutters from the frames) all as specified.

S&F for 2nd class hard wood, 30 mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. divided into squares with plain chamfered mitered and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, section 8, clause 8.20 (a); supplied & fitted to Chowkats all as specified.

S&F for 2nd class hard wood, 35 mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. divided into squares with plain chamfered mitered and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, section 8, clause 8.20 (a); supplied & fitted to Chowkats all as specified.

S&F for 35mm thick, 2nd class hard wood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied & fitted to chowklats all as specified

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification

Fixing only Curtain rails anodised aluminium alloy with fixing brackets, etc, as fixing in repair work complete all as specified and directed. (Note: Material will be issued under "Sch B" for "free for fixing")

S&F for venetian blinds/Verticle blinds with wooden fabric stips and GI powder coated frame including opening/closing devices(ropes) in any colour and pattern complete all as specified and directed

S&F 150mm long extruded aluminium alloy handles fabricated type anodised all as specified

S&F 100 mm long extruded aluminium alloy handles, fabricated type anodised all as specified

S&F 150 mm long alluminium, anodised, barrel tower bolts of extruded section all as specified

S&F 100 mm long alluminium, anodised, barrel tower bolts of extruded section all as specified

S&F 300 mm long, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy all as specified.

S&F 100mm size MS butt hinges medium weight cold rolled complete all as specified & directed.

S&F 75mm size MS butt hinges medium weight cold rolled complete all as specified & directed.

S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and including II nd class hard wood beads straight (any size) for glazed or gauged joinery , renewed including mitrted etc and painting exposed surfaces of beads with two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified

S&F for door closer, hydraulically regulated, designation No. 3, universal type suitable for door shutters of weight between 61 to 80 Kg with aluminium (die cast) body, fixed in repairs all as specified

Hacking out old broken glass ( any thickness, size, quality or description) from wooden/steel frames or stone concrete or brick surrounds, glazed with putty of fixed with beads complete all as specified and directed.

S&F 5mm thick figured glass, pin head type and glazing with aluminium beeding in squares n exc 0.5 sqm in each pane fixed all as specified

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L for PCC Type D2, 1:4:8 (using 40 mm graded granite stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for RCC M-30 design mix (using 20mm graded granite stone aggregate) as foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-30 design mix (using 20mm graded granite stone aggregate) as walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L for providing formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for flat rough finished surfaces of concrete all as specified.

M&L for providing formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for flat rough finished surfaces of concrete all as specified.

M&L for providing formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for flat fair finished surfaces of concrete all as specified.

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for boulder filling dry (using undressed quarried stones roughly conforming to specified size of boulders), hand packed tightly at back side of retaining wall as specified and directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches, in weep holes complete all as directed.

Rough excavation exceeding 1.50 mtr but not exceeding 3.00 mtr deep and getting out in hard/ dense soil complete all as specified and directed.

Excavating over areas, not exceeding 1.50 mtr deep and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil complete all as specified and directed.

Back filling at retaining walls using approved earth obtaining from excavation, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil. all as specified and directed.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified.

M&L 75 mm thick PCC (1:4:8) Type D2 (using 40 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. finishing surfaces of concrete even and rough complete all as specified.

M&L for sand filling/cushioning under floors or in foundations including watering and consolidation for laying interlocking tiles.

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade and pointed in coloured cement to match the surfaces.

M&L for chequered cement concrete colour tiles 20cm x 20cm x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry on floors/ steps, over including screed bed or bedding layer of 15 mm thick in CM 1:6 complete all as specified and directed.

M&L PCC 1:3:6 Type C1 (using 20 mm graded granite stone aggregate) as in PCC kerb stones including formwork complete all as specified.

M&L for boulder pitching (using undressed quarried stones roughly conforming to specified size of boulders), hand packed tightly and pitching is grouted with cement and sand mortar 1:6 complete all as specified.

Labour only for boulder pitching, hand packed tightly and pitching is grouted with cement and sand mortar 1:6 complete all as specified. Note: Boulder stone obtained from dismantling shall be reused in this item.

M/s Sharma Trading Company

Binod Hawlader

Kakolil Trade Agencies