ARC 2026-2028 for Day to Day Maintenance, Repairs n Renovation of Furniture Items, Furnish Items, CP n Sanitary Items, Plumbing, Sewerage Services, Misc Civil Work at NHAI HQ Buildings, Sec-10, Dwarka, ND and NHAI hired office building, New Delhi.

Part A Civil Works

Earth Work and Termite Treatment

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains ( ( not exceeding 1.5 m in width as well as 10 sqm on plan) including dressing on side & ramming of bottom, for all lifts getting out and disposal of surpluse excavated Soil with in alead of 50 metre, as directed by Engineer-in-charge.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil:

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Anti-termite treatment for insecticides using Aqua base spray for pest (for bugs, cockroaches, silverfish, spider, termites, mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical @ 0.5 litres per sq.m. by a hand operated pressure pump on wall surfaces, ceiling, electrical fixture,electrical lines including drilling holes inplaces where source of termite is detected squirting chemical solution into the holes and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture).

Cement Concrete Work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

Centering and shuttering including strutting, propping etc. and removal of form work for :

Centering and shuttering including strutting, propping etc. and removal of form for

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Brickwork and Plastering Work

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

12 mm cement plaster of mix :

Neat cement punning.

Structural Steel Work

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Supplying, fabricating and fixing M.S.Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including, cutting, hoisting, fixing in position and applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent , including welding and bolted with special shaped washers etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per specifications and direction of Engineer-in-charge. Hot finished Seamless Type Tubes

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Flooring and wall cladding work

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

30mm thick gang saw cut stone

Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part there of.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Providing and fixing stone work in Wave Pattern/ Geometric Design Pattern/ Abstract form,Linear Pattern straight pattern as per Design/ Drawing. Machine cut, mirror/ diamond , Marble Combination stone work for wall lining (veneer work) including dado, skirting, risers of steps etc, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

Stone work in Wave Pattern/ Geometric Design Pattern/ Abstract Pattern, Linear Pattern Straigh Pattern as per Design/ Drawing. Machine cut, mirror/ diamond polish, Marble Combination stone work in Flooring, skirting and steps etc, stones of different finished surface texture, laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Architect/ Engineer-in-Charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : (The cost of protecting stone work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (The cost of protecting stone work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Grout

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness

Removing and refixing existing sand stone cladding or Granite/ marble wall clading laid in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary repairs and cement pointing with same mortar complete, including disposal of rubbish to dumping ground, all complete as per direction of Engineer-in-Charge.

Wood & Aluminum Work

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. 35mm/50mm as per direction of Engineer Incharge

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 /450 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing powder coated telescopic drawer channels 300/350/400 mm long with necessary screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing marine plywood for cupboard shutter of approved quality ( century/ kitply/ greenlam or it equivalent) confirming to IS: 710 including cutting into required size, jointing with nails adhesive, P/F 4mm thick second class teak wood beading on its edges with nails and adhesive etc. complete as directed by the EIC.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium/ Wooden door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Including Cost of aluminium/ Wooden snap beading):

Water Supply Work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings with 6 to 10 Kg/cm2 Pressure This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

Providing and fixing ball valve (brass) of approved quality, High or low pressure, complete :

Providing & Fixing 3 Layer PPR (Polypropylene Random Copolymer) Pipes, conferming to IS:15801 UV Stabilised & anti microbial fusion welded, having thermal stability for hot & Cold water supply , Including all PP-R Plain & brass threades polypropylene randam fittings including trenching, refilling & testing of joints complete as per direction of engineer incharge. (Astral, Supreme, Ashirvad, etc.), ( External Work)

Tank Nipple 4" PPR

Tank Nipple 2" PPR

Tank Nipple 1.5" PPR

Ball Valve 4" PPR

Ball Valve 2" PPR

Ball Valve 1.5" PPR

Sintex Pure Water tank 10,000 Litre( Rate Including unload to terrace floor G+7 )

Sintex Pure Water tank 5000 Litre( Rate Including unload to terrace floor G+7 )

Sintex Pure Water tank 2000 Litre( Rate Including unload to terrace floor G+7 )

Sintex Pure Water tank 1000 Litre( Rate Including unload to terrace floor G+7 )

Sintex Pure Water tank 500 Litre

Ball Cock of Flush Tank

Ball Cock of water cooler

CPVC T-2" Astral or eqivalant

CPVC bush 2"X 1" Astral eqivalant

CPVC Socket 2" Astral eqivalant

CPVC Ball valve 1" Astral or eqivalant

Solvobond CPVC 707 200 ML

CPVC Union 2" Astral or equivalent

CPVC Pipe 1" Astra Astral eqivalant

CPVC FTA Brass 2" Astral or euivalent

CPVC Elbow 2" Astral OR euivalent

Gate valve 2" DRP

Sanitary Work

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Providing and fixing white vitreous water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and makinggood the walls and floors wherever required :

Providing and fixing P.V.C. low level flushing cistern with manually controlled device conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Supplying, Installation, Testing and Commissioning white vitreous china extended wall mounting water closet of size 525x360x420 mm with intergrated jet of approved shape including seat cover, and fittings, nuts, bolts and gasket etc complete including cutting and making good the wall wherever required.(MAKE - CERA -Cat No.-S1051119 , CERA - Cat No.-B1510101 CARAT WITH JET)(MAKE-JAQUAR,CAT NO-SLS-WHT-6951J)(MAKE-KOHLER,CODE-K-16817IN-SR-00)

Supplying, Installation, Testing and Commissioning of twin flush concealed cistern with knob and frame and fittings, nuts, bolts and gasket etc complete including cutting and making good the wall wherever required.(MAKE - CERA (Cat No. -B1110108 & B1120118)(MAKE-TOTO,CODE-WH076MFF)(MAKE-KOHLER,CODE -K-77028IN-M-NA)

Supplying, Installation, Testing and Commissioning Table top wash basin with C.I. brackets with waste of standard pattern with waste fitting, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 640x450 mm.(MAKE - CERA (Cat No. -S2020132,F8050301)(MAKE-TOTO,CODE -LW710CM#NW1,T6JV6)(MAKE-KOHLER,CODE -K-4117IN-XBV-0)

Supplying, Installation, Testing and Commissioning white vitreous battery based infrared sensor operated urinal of approx. size 360 x 330 x 740 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.(MAKE - CERA (Cat No. -S4010101)(MAKE-TOTO,CODE -USWN810BE#XW)(MAKE-KOHLER,CODE -K-4915T-0)

Supplying, Installation, Testing and Commissioning C.P. Single lever basin mixer with 355mm long extended body 450mm braided connection pipe (without pop-up) including cutting and making good the wall wherever required. (MAKE - CERA (Cat No. -F1004452)(MAKE-TOTO,CODE -TTLR303FV)(MAKE-KOHLER,CODE -K-97067IN-4-CP)

Supplying, Installation, Testing and Commissioning C.P. Bottle Trap including cutting and making good the wall wherever required. (MAKE - CERA (Cat No. -F8060401)(MAKE-JAQUAR,CAT NO-ALD-769L300x190)(MAKE-KOHLER,CODE -K-7314IN-CP)

Supplying, Installation, Testing and Commissioning of Toilet Paper Holder fixed with CP brass screw complete.(MAKE - CERA (Cat No. -F5002109)(MAKE-JAQUAR,CAT NO-AHS-1553)(MAKE-KOHLER,CODE -K-11584-CP

Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.(MAKE - CERA (Cat No. -F2007161)(MAKE-JAQUAR,CAT NO-ARI-39041)(MAKE-KOHLER,CODE -K-37320IN-4-CP)

Supplying, Installation, Testing and Commissioning C.P. cast brass twin coat hooks fixed to wooden cleats with C.P. brass screws.(MAKE - CERA (Cat No. -F5004108)(MAKE-JAQUAR,CAT NO-AKP-35761P)(MAKE-KOHLER,CODE -K-15247IN-CP)

Supplying, Installation, Testing and Commissioning of Towel Ring fixed with CP brass screw complete.(MAKE - CERA (Cat No. -F5002105)(MAKE-JAQUAR,CAT NO-ACN-1121BN)(MAKE-KOHLER,CODE -K-5631IN-CP)

Providing, fixing, Testing and Commissioning C.P. liquid soap dispenser with bracket of the same materials of approved quality colour and make including cutting and making good the wall wherever required. (MAKE - CERA (Cat No. -F5002111)(MAKE-JAQUAR,CAT NO-ACN-1135N)(MAKE-KOHLER,CODE -K-10712D-CP)

Providing and fixing 15mm C.P. brass angle valve (Jaquar Cat No. 053 / Parko cat. no. 2119A/ Kingston cat. no. KRA 014 or as approved by the Engineer-in-Charge) union nuts complete with C.P. brass flange including cutting and making good the walls wherever required.

Supplying, Installation, Testing and Commissioning Stainless Steel kitchen sink with drain board (304 grade SS) with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.(MAKE - CERA (Cat No. -B4512203)(MAKE - SANJAY CHILLEY) Kitchen sink with drain board 1040x500 mm bowl depth 205mm.

Supplying, Installation, Testing and Commissioning 15mm C.P brass mixing fitting for kitchen sink with swivel spout with connecting legs and wall flange complete. Including cutting and making good the walls wherever required.(MAKE - CERA (Cat No. -F2011511)(MAKE-JAQUAR,CAT NO-DRC-37165)

Providing and fixing hand shower (Health Faucet) with 6mm dia., 1 m long PVC tube and wall hook all complete Jaquar ALD-CHR-563 or as approved by the Engineer-in-Charge.

Providing and fixing C.P. brass two way bib taps long body (Jaquar Cat NO. 15041 or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required.

Providing and fixing C.P. brass bib taps long body (Jaquar Cat NO. 107 or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required.

Providing and fixing C.P. brass pillar cock of approved quality (Seiko or equivalent) conforming to IS:8931 for wash basin.

P/F 150 x 150 mm PVC moulded three piece Nahani trap jali with or without hole i/c cutting& making good to the flooring etc. complete.

Providing and fixing white glazed vitreous European type water closet with seat and lid, C.P. brass hinges and rubber buffers, vitreous china flushing cistern with fittings, brackets, overflow pipe with mosquito proof coupling of an approved design, including cutting and making good the walls and floors where required.

Providing and fixing CP brass concealed stop cock reduced body Jaquar Cat No. 089 / Parko cat. No. 2117 / Kingston cat. No. AGR 306 or as approved by the Engineer-in-Charge.

Providing and fixing S.S. hinged grating, 6mm thick with frame as approved by the Engineer-in-Charge) including setting in floor with cement mortar 1:3.

Supply and fixing of Hindware Studio Cistern Catalouge No-21028, Ivory Floor mounted WC or equivalent

Supply and fixing of Hindware Ultra wall mounted closet, Catalouge no-20006, Ivory, wall mounted WC or equivalent

Supply and fixing of Toshi Wall mounted Urinal automatic sensor Model No: T-1032

Supply and fixing of Cera wall mounted urinal automatic sensor

Providing and fixing 600mm x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Painting and Polishing Work

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Note: Measurement Will be 30% of plastic emulsion paint for Old Work

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Note: New Work

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing walls with water proofing cement paint of required shade :

French spirit polishing :One or more coats on old work

Melamine polishing on wood work (one or more coat).

French spirit polishing :Two or more coats on new works including a coat of wood filler

Finishing walls with textured paint of required shade : Old work (One or more coats) applied @ 1.82 ltr/10 sqm..

Finishing walls with textured exterior paint of required shade :

Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications

Wall painting with Royal Mate paint of approved brand and manufacture to give an even shade: One or more coats on old work

Polishing in high gloss/malt finish melamine clear polish on wood work in required color wooden shade texture with following process in the sequence as detailed below: 1.The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of seater with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of seater coat with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing grooves . Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed for dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This first coat is allowed for dry for 24hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Enginner in charge (Final cost to be done 1 or 2 layer without gap of time.

Water Proofing work

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Roofing & Shading Work

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

Dismantling and removing existing broken/damaged polycarbonate sheet roofing of any thickness from shed or similar structure, including carefully unscrewing and removing all fasteners, nuts, bolts, washers, sealants and accessories, lowering the materials to ground level, stacking serviceable materials separately and disposing of unserviceable materials/debris as directed, the rate shall include all labour, tools & tackles and incidental charges, complete in all respects as per direction of Engineer-in-Charge.

Providing and fixing 10 mm thick UV-stabilised multiwall/sandwiched polycarbonate sheet roofing for Porch shed up to any pitch, of approved make, colour and finish, having integrally reinforced straight polycarbonate purlins within the sheet for enhanced strength and load bearing capacity, manufactured with uniform thickness free from air pockets and defects with inbuilt UV stabilisation for weather resistance and durability, and being clear/translucent/pigmented as specified, including cutting to size, drilling and fixing with suitable polymer coated ‘J’ or ‘L’ hooks, bolts and nuts, aluminium/SS fasteners, EPDM rubber gaskets, washers and approved sealant to ensure watertight joints, the rate including all materials, labour, tools and tackles, wastage and installation, complete in all respects as per manufacturer’s specifications and direction of Engineer-in-Charge. ( Make: Sabic (Lexan), Gallina India / Gallina (Italy tech), Palram / Palram Sunlite or Danpal / Danpalon)

Dismantling of FRP sheet and removing awning cloth or porch upto any pitch including disposal of unserviceable material all complete as directed by Engineer-in-charge.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

Providing & fixing of awning cloth/ porch cloth roofing up to anypitch having water repellent characteristics.The sheet shall be even in colour, without any visible defects and shall conform to IS 5915:1970 , including fixing with necessary polymer coated MS Rivets of required size, all complete as directed by Engineer-in-charge

False Ceiling Work

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the rate of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm or both sides of joint and two coats of primer suitable for board, all as per manufacture's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

Acrylic false ceiling tiles as approved by engineer incharge

Providing and fixing false ceiling tile 15 mm thick densified tegular edge eco friendly lite weight calcium silicate false ceiling tiles fo approved texture spintone/cosmos/Hexa or equivalent of size 600 X 600 mm, Make -Armostrong design with optra glass wool as per direction Engineer Incharge

Removing, repairing and refixing of existing false ceiling with tiles of any type by making the grid in proper line and level by adjusting existing supports, repiring or/and existing supports/ hangers/ grid members and providing new supports to match with existing ones including repairs and cleaning of metal tiles, placing the tiles in position etc complete as directed by EIC. Rate is inclusive of all labour and material required for entire levelling, repairing, cleaning work and charges for T/P.

Providing and fixing false ceiling system manufactured by M/s. Armstrong /Aerolite World Industries / Gyproc using hot dipped galvanized steel section, rotary stitched main tee of size 24mm x 42 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 24 mm x 42 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using 2.0 mm. thick pre-straightened GI wire laying ARMSTRONG OPTRA of ceiling tiles of size1200 X 600 X 20mm having NRC 90 Light reflectance of >85% (WT), thermal conductivity k = 0.052-0.057 W/m0K, Humidity Resistance of 99% , having Fire Performance CLASS O / CLASS 1 (BS 476), surface having 3 coats of white paint with Fine Fissured, back of the tile duly sanded and finished with a coat of protective paint over the formed grid complete.Note : Rate quoted for the item deemed to include all wastages

Supply and Installation of approved , Veneer laminated finish, square edge, FR grade, fiberboard core panel of size 595x595x12mm thick having density 800Kgs/ m3, weight 9.6 kg/m2 which is suspended by using 0.3mm thick and 24mm wide pre coated metal T24 grid system. The T24 Grid system of 600x600mm module shall include wall angle(WA24W30) with equal flanges of size 24mm wide, length 3000mm, 0.4mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers.

Then suspend the Main T24 (MT24W36) having flange width 24mm, height 38mm and length 3600mm from the soffit with help of soffit cleat and wire rod along with leveling spring clip at 1200mm c/c. Cross T24 (CT24W12) with flange width 24mm, height 25mm and length 1200mm is then interlocked into the pre-cut slots in the Main T24 at 600mm centers in the direction perpendicular to the MainT24. Finally Cross T24 (CT24W06) having flange width 24mm, height 25mm and length 600mm are then interlocked into the precut slots in the 1200mm Cross T24 at 1200mm centers and in direction parallel to the Main T24. Sonator square edge of size 595x595x12mm thick shall be placed into the grid size of 600x600mm. Note:- Skelet T24 should be of same shade and finish as that of Sonator panels. • Core - Fiberboard • Fire – Class 1 & P • Acoustics – NRC upto 0.3(system NRC) • Climate (OC RH) – 40, 70 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 3 • Strength, Load capacity (Kg) - Antisag

Supply and installation of LOOP® Type 2 system formed as an open metal ceiling with an open area of more than 50% and to the flare [5mm] of the perforation pattern [RV-50-40] the ceiling has a three-dimensional visual effect and hides the insight into the plenum. Bypassing the perforation, the S-shaped sides of the LOOP® interlock both the long and front side joint with a nonmagnetic suspension, the elements are installed with a circumferential 1 mm joint, thus compensating tolerances in x and y direction. The non-magnetic suspension system effectuates a self-alignment of the elements [puzzle effect]. The module size 966x1115x1.0mm GMS is perforated with 60mm deep drawn holes .The substructure consists of a form perforated L profile [U1040] as a lateral grid which is suspended from the ceiling with nonius adjustable upper and lower parts or with threaded rods using official approved dowel plugs. The grid profiles are to be connected together at the ends by means of longitudinal connectors [U 1041] [screw fasteners]. The spacing of the grid profile is according to the requirements of DIN EN 13964 as well as the loads of the system and to be determined and checked by the contractor. The profiles are attached to the walls with U 1042 wall brackets. On profiles angles, C-band raster as secondary profiles are bolted on by means of C channel hanger bracket with M6 bolts. The longitudinal connections of the C-profiles are made by C profile connectors. The attachment to the walls is made with wall brackets.

The ceiling elements are provided with magnets at the back and are force-fitted to the C-profiles. Thus, they are removable without using tools. They are secured with ropes against swinging down in an uncontrolled way. Only construction parts approved by the manufacturer may be used. Provide necessary supports, provisions as per the architects / PM’s Instructions. Finish of ceiling is in powder coated RAL 9016 white colour or RAL 9006 Silver Grey or Black colour.

Providing and fixing in true level, Open cell False ceiling of approved make containing ‘U’ shaped sections with sharp edges of dimensions 15mm (Flange width) X 38mm (web height) manufactured out of Aluminum of 0.40mm gauge of white colour. The open cell ‘Lock-in’ ceilings shall have 2 components viz. Open cell Main Carrier (top and bottom notches) of length 2000mm, and Horizontal Carrier of length 2000mm. The Open Cell Main Carriers shall have notches on top or bottom spaced at 100mm to be used with matching Horizontal Carriers. The main carriers are suspended at every 600 mm c/c spacing with spans longer than the length of main runner connected by means of connector. The ‘U’ Shaped horizontal carriers are to be interlocked by matching the top and bottom notches to form cells of size 100 mm. the perimeter trim to be secured at every 450mm c/c including provision for opening like diffusers, grills, light fittings, speaker and smoke detector etc., with necessary materials, labour, scaffoldings, tools and tackles, plants etc., and as directed by the Engineer-in-charge. [Note that no deduction shall be made from the overall area of the false ceiling for the openings].

Providing and fixing Baffle False ceiling system of approved make. The baffle ceiling system fixed to the sizes of baffle panels as per drawing, is to comprise of 100mm (h) x 50/25mm (w) with 200mm c/c spacing, 0.6mm thick roll form aluminum section baffles and the length of the panel is up to 4m. Panel shall be clipped to a baked enameled aluminum carrier of 35mm height x 62mm width x 0.95mm thick in a standard length of 5mtr. The primary hanger bracket are fixed by means of 6mm dia galvanised steel threaded rods spaced equally at 1.2m c/c suspended from roof slab. The entire baffle ceiling system is to also include provision for all fixtures like diffuser, grill light fittings, speaker and smoke detector etc., with necessary materials, labour, scaffoldings, tools and tackles, plants etc., and as directed by the Engineer-in-charge. Note: All baffle to be used should be with appropriate % of recycled content. The contractor should provide the material cut sheet/ declaration from manufacturer mentioning the recycled content used in manufacturing of baffle to be used).

Supply and installation of Synth Slim, polyfibre panels, core-pigmented, high-density, SynthPF rigid panels of size 1200x2400x9mm thk, volume density 210 - 230kg/m3, weight 1.9 - 2.1kg/m2 and ,square edge, magnesite-bonded pinewood fibre ceiling tile of size 600x1200x10mm, volume density 400Kgs/m3, weight 4kg/m2 installed by using ceiling framework.

The ceiling framework system shall include Strut WC25 Wall channel, fully knurled, sectional thickness 0.55mm, length 3600mm, unequal flanges of 20 & 30mm and web of 25mm, fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then suspend Strut MC45 Main channels, fully knurled, sectional thickness 0.8mm, length 3600mm, equal flanges of 15mm and web 45mm from the soffit at 1200mm centers with Strut SA25, fully knurled, Suspender angle with sectional thickness 0.55mm, unequal flanges of 25 & 10mm. Strut CC25 Cross channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 35mm, depth of 20mm and equal flanges 9.5mm is fastened to the Strut MC45 perpendicularly at 600mm centers. Strand is installed on the Strut CC25 with suitable fasteners in staggered manner. Longer edges of the strand should be perpendicular to length of CC25.

Prior to installation of Slim panels, ensure Strand surface behind is flat, dry and free from dust or other contaminants and leveled. Slim panels are then adhered to Strand surface behind with stick S7 adhesive.

Technical Parameters of system

• Fire (Class) – 1 & PB • Acoustics – NRC ,0.6 • Thermal conductivity (W/mk)– na • Climate (°C, RH) – 50, 99 • Light reflectance (%) – Colour Dependant • Green (VoC, RC %) – Nil, 30

The Strut ceiling framework system shall include Strut WC25 Wall channel, fully knurled, sectional thickness 0.55mm, length 3600mm, unequal flanges of 20 & 30mm and web of 25mm, fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then suspend Strut MC45 Main channels, fully knurled, sectional thickness 0.8mm, length 3600mm, equal flanges of 15mm and web 45mm from the soffit at 1200mm centers withStrut SA25, fully knurled, Suspender angle with sectional thickness 0.55mm, unequal flanges of 25 & 10mm. Strut CC25 Cross channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 35mm, depth of 20mm and equal flanges 9.5mm is fastened to the Strut MC45 perpendicularly at 300mm centers. PVC Vinyl core UV treated H-Spline having sectional thickness 2mm and length 2400mm to be fixed perpendicular to the Cross channel (CC25) at 600mm centers. The Kerfed edge Strand panels shall be then inserted into the H-spline along their long edges of 1200mm against framework to perfect fit with staggered short edges.

Technical Parameters

• Core Variants - Pinewood fibre • Fire – Class 1 & P • Acoustics – NRC 0.95 • Climate (OC RH) – 50, 90 • Termite resistance – Yes • Light reflectance – color dependant • Green (RC %) – 10 • Hygiene (VoC, Clean room) – Low • Strength, Load capacity (Kg) - Ball impact

Providing and fixing backlit Ceiling in acrylic solid surface sheet (basic series) of approved make, manufactured as per guidelines of ISO19712. The acrylic solid surface should be conforming to standards of Green Guard certified, OEHHA, AQMD, UL, Euro class BS1 for fire resistance. Ceiling Installation to be done in translucent glacier ice color, thickness (12 mm), design backlit provision as approved by architect or Engineer-in- charge. The material should be CNC cut to achieve the desired design as per architect. The CNC cut Acrylic solid surface sheet to be fixed on ceiling with the help SS sling wire & squirrel system. Slings to be fastened on ceiling with the help of Hilti/ or approved fasteners. Adhesive of the same color. The rate is inclusive of framework, material and required pattern approved. The Acrylic Solid Surfaces should be installed by company authorized Quality Network Fabricators & covered under 5 years warranty by the supplier or company. Electrical and lighting accessories would be paid extra. The rate is inclusive of all operation,framework, material and required pattern approved by Engineer-in- Charge.

Rainwater Work & Fittings

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Pressure 6 to 10 kg/cm2 (i) Single socketed pipes.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Repairs to Building

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineerin- Charge.

Taking out existing CC interlocking paver blocks, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in- Charge.

Laying existing cement cocrete interlocking paver blocks or providing & laying new interlocking paver blocks in case of damaged old block of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-incharge.

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line of required dia.

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-incharge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Structural Protection Work

Providing and fixing Scaffolding net of required width made of high density Polyethylene UV stabilized knitted on warp knitting machines having density 100grams/sqm and shading coefficient minimum 75% around the construction site/ for vertical extension as per requirement including fastening/tying with building/scaffolding pipes or with any other fixtures etc. complete as per direction of Engineer-in-Charge. (One time payment shall be made for providing Scaffolding net from start of work till completion of work including shifting if any. The Scaffolding net shall be the property of the contractor on completion of the work)

Providing and fixing of good quality plywood or GI Sheet cover for glass glazing and windows, Acs outer units, cladding etc. at all heights to protect these items from concrete lumps during dismantling of distressed structure and any other loose material of inner & outer face of the building at all height, complete. The payment will be made once irrespective of duration of cover or shed provided. The rates are inclusive of erection of tin sheets and dismantling of same, materials, manpower, tools and tackles etc. and disposal of excess debris into approved municipal dumping yards, all complete.

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.

Anticorrosive treatment to exposed reinforcing bars using Zn rich epoxy phenolic material (with solid content grater than 80%) of approved anticorrosive product @ approx. 5.5 sqm/lt. all complete as per direction of Engineer-In-Charge.

Drilling suitable holes in reinforced or plain concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC Beams, lintels columns & slab to introduce steel bar for sunshades/balconies including fixing the steel bars in position usingepoxy resinanchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer incharge

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.

Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2)

Providing and laying SBR Polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structural members e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of RCC member. Note: Rates shall be for finished surface area of concrete and shall include the cost of making holes in existing RCC slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved Super-Plasticiser for rendering concrete as flowable self compacting and SBR polymer but shall exclude cost of reinforcement, bond coat, Shear Keys, centering and shuttering, strutting, propping etc (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)

Shear Key:Providing and fixing of L/U shaped 150mm long, 10mm dia mild steel shear key after drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, columns and slabs to introduce steel bars including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm or 10 times the dia. of the bar, whichever is greater, in RCC beams, lintels, columns and slabs to introduce steel bars including fixing the steel bars in position using epoxy resin anchor grout of approved make (HIT HY 170 whichever required of HILTI or equivalent make) but excluding the cost of reinforcement, all complete as per direction of Engineer-In- Charge.

Providing and filling expansion joints with approved polysulphide sealing compound (confirming to grade BS:4254:1983 or IS-12118, Part-I&II - 1987) including painting the sides of slab upto a depth of 20mm with approved appropriate primer to receive the specified sealing compound, providing and applying bond breaking tape on top edges of joint to prevent accidental spillage of sealant on top surface and to give a neat finish to the sealant has been applied and tooled, all complete as per specification and direction of Engineer-in-Charge.

Providing and fixing sheet covering over expansion joints with iron screws as per design to match the colour/ shade of wall treatment in position copper plate as per design for expansion jionts.

Filling the gap in between aluminium frame & adjecent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved qualityas per architectural drawing and direction of Engineer-in charge complete

Providing & Laying weather proof sealant on outer joint of approved make conferming to IS & directed by Engineer in charge

Canopy Work

Stainless Steel Glass Canopy:-Repairing, Supply & Installation of Canopy (Conforming to SS304 Grade, Satin Finish). Withavarious size of canopy. Structure consisting of SS304-219, 168 Tubular Sections with 75 x 75 Sections, fixing Plate, Provision for water drainage and canopy lighting, with4- Arm Stainless Steel Ozone Spider Glass fitting Arrangements with 8+1.52+8mm Thick Laminated Toughened Glass fixed with clear weather Silicon as per drawing and details. direction as per Engineer In Charge.

Supply & Erection of Size 11.9mx12.5m (Actual as per site) Stainless Steel Sky Light Over Atrium as per Architecture and Structural drawings, including supply and fixing of Laminated glass of 8mm thick clear toughened glass +1.52PVB+8mm thick clear toughened glass+1.52PVB+8mm thick clear weather Silicon toughened glass (All odd size as per drawings) fixed with Stainless Steel Ozone 4-Arm Spider Fitting Arrangements with screw, nut and bolts. The Stricture Steel consist of all Standard and Buld up sections required for the Dome with welding complete as per drawing. The Steel Structure include all size, cutting, bending, drilling, grinding and Structure welding to required odd shape etc. direction as per Engineer In Charge.

Designing, Enlarging, supplying, execution, fixing and installation of stain glass mural sandwich panel in 5mm stain toughened glass panel+5 mm thick toughened clear glass facing outside. Concept of stain glass will be specially be designed keeping the company's profile in mind the art mural will enhance the ambience and would improve its look aesthetically. Material: The material used in making the stain glass will be lead, 5 stain toughened glass panel+5 mm thick clear toughened glass, Imported resins and staining chemicals, imported color dyes overall thickness of glass in 10mm,thw two panes will be sealed with silicon as/approved from all sides. Framing: Cost includes frame of aluminum powder coating which runs around the glass panel fixed to wall/RCC column.

Office Furniture Work

Providing Fabric Visitor Chair of approved make Godrej, Nilkamal or equivalent as per direction of Engineer In-Charge Pedestal Base: Chrome finish with 5 wheels Arm Material: Steel Covered with Polyurethane Seat material: PU Foam covered with Fabric Chair Type: central tilt Height Adjustment ± 5(mm): up to 90 mm Arm Type: Fixed Arm Movement: N.A Overall Chair Height ±15mm: 890mm Warrantee period in number of years: 2 years

Providing Executive Aero High Back Synchro Chair of approved make Godrej as per direction of Engineer In-Charge Dimensions W x H x D (cm): 76.1 x 114-128.2 x 76.1 Seat Height (cm): 45.5 x 55.5 Finish Color: Black Primary Material: Glass Filled Nylon Upholstery Material: Fabric Armrest Type: Adjustable Net Weight (kg): 16 Warranty: 1 Year

Providing Premium Executive High Back Chair for CMD/ Member make Godrej as per direction of Engineer In-Charge Recommended model: La Sede / Posture Perfect / Thrill Executive Upholstery: Premium leather/leatherette, preferably black, dark tan or camel Back: Full high back with contoured lumbar support Armrest: Adjustable, premium finish Mechanism: Multi-position tilt/recline locking with anti-shock Base: Heavy-duty 5-star revolving base Gas lift: Height adjustable Seat: High-density moulded PU foam Rotation: 360° Warranty: 1 Year

Providing Executive Aero Mid Back Synchro Chair of approved make Godrej as per direction of Engineer In-Charge Dimensions W x H x D (cm): 76.1 x 114-128.2 x 76.1 Seat Height (cm): 45.5-55.5 Finish Color: Black Primary Material: Glass Filled Nylon Upholstery Material: Mesh Fabric Net Weight (kg): 15.5 Warranty: 1 Year

Providing and Repairing Hydraulic system for chairs, with necessary spare parts, tools & plant including labour of approved make: Godrej or Equivalent all complete as per direction of Engineer in-Charge.

Providing and Repairing Chrome coated wheels for chairs, with necessary spare parts, tools & plant including labour of approved make: Godrej or Equivalent all complete as per direction of Engineer in-Charge.

Providing and Repairing Office Chair Armrest for chairs, with necessary spare parts, tools & plant including labour of approved make: Godrej or Equivalent all complete as per direction of Engineer in-Charge.

Change of Upholestry with fabric and mesh fabric inclusive of material and labour all complete (Both Sides)

Supply of Steel 2 Doors Godrej or Equivalent Almirah Size- 900X1200X400

Supply of Steel 2 Doors Godrej or Equivalent Almirah Size- 915x1980x450

Supply of Wooden Office Almirah Geeken or equivalent Size 1980X900X450MM all body made out 18mm pre laminated Particle board woth pvc edge bidding.

Supply of Wooden Office Almirah Geeken or eqivalent Size 900X1200X400 mm all body made out 18mm pre laminated Particle board woth pvc edge bidding.

Cost for Polish each wooden chair/ wooden visitor chair/wooden sofa chair (Including Applying Oil based putty, Scrubing etc. to make surface smooth, Spot less & Polishing)

Providing & Fixing Wooden drawer having a size of 0.55 m x 0.45 m x 0.7 m including handle, channel, lock & other fitting as per the direction of EIC.

Wooden cabinet/almirah with 18mm Comercial board sunmica on one side of thickness 1.5 mm, shutters fix with piano hings and Brass handle etc. Dah fastner, nail, fevicol etc. for fixing complete in all respect

Modification of old Almira to new size With Veneer

Modification of old Almira to new size With Sunmica

Providing & placing sofa Wooden structure of sofa to be fabricated using good quiality hardwood duly seasoned and applying anti-termite paint of approved brand & manufacture to ensure stability of the frame, On the wooden base frame of the sofa to be provided with M>S> helical spring, sides & back with jute strips, with polyfill covered with jute & finished with thick marking cloth before doing fina finished with leatherite have basic cost not less than 1000/- Pet Mt. Seat - 30-32Kg/cum density PU Foam, 100mm thick, Back - 32Kg/cum density PU foam, 60mm thick, Sides (inside) - 32 Kg/cum density PU Foam, 45 mm thick Sides (outside) & back (back side) - 32 Kgcum density PU foam, 25mm thick. Seat shall rest on SS square frame of size 25mm x 25mm supported be legs made of 25mm x 25mm square SS section of height 225mm. All SS work should be in grade 304. Base of sofa should be infilled with suitable woode sections so as to give proper support to the seat. Height of the base of sofa shall be 200-250mm(approx). Finished width of arm shall be 100mm after upholstery work. Sofa to be fully upholstered using approved fabric (titch) of A grade of desired shade duly embossed including providing & fixing of all other related materials including hardwares etc. complete as directed by the Engineer in charge

Polishing & Crystallization

Providing and Executing honing, polishing & Crystallization of Marble /Granite/ italian Floor A. Honing of floor using Grits 100 to 3000 to Remove all particles and scratches from floor. B. Scrubing of floor using Neutral floor cleaner to remove all Dirt. C. The floor to cleaned with Taski R2. D. Crystallization of marble with high quality Crystallization powder for floor marble. E. Buffing with buffing pad & Liquid Crystallization to be done for floor marble. F. The above items includes all type of material, machineries, consumables; man power etc.required to carry out the job and are in the scope of contractor.

Providing and Executing honing, polishing & Crystallization of Marble /Granite/ italian Floor at G/f Reception area, 6th floor area and 7th floor area and all floor (2nd to 5th) lift lobby Area which includes. A. Honing of floor using Grits 100 to 3000 to Remove all particles and scratches from floor. B. Scrubing of floor using Neutral floor cleaner to remove all Dirt. C. The floor to cleaned with Taski R2. D. Crystallization of marble with high quality Crystallization powder for floor marble. E. Buffing with buffing pad & Liquid Crystallization to be done for floor marble. F. The above items includes all type of material, machineries, consumables; man power etc.required to carry out the job and are in the scope of contractor. Estimated Floor/ Wall Cladding Area: 1065 Sqm ≈ 1200 Sqm

Blind Works

Supply and Installation of Roller Blinds having the Control unit: The Control unit is made of high strength reinforced plastic. The clutch is of wrap spring design. High carbon steel springs are provided to transmit motion from driving to driven members of clutch mechanism. Clutch is operated directionally by the use of endless beaded chain. Clutch never needs any adjustment. Head rail: It is an aluminum extruded rail Powder coated in white. Control unit and Idler are mounted on the Head rail with powder coated M.S. brackets. Roller tube : It is Aluminum alloy Extruded grooved tube, which is anodized.Size- 38mm- O.D.; weight - 0.38 kg/mtr,Alloy & temp- 6063-T6 Fabric is fitted on the tube with double sided tape. The END PLUG shall be moulded of plastic with a steel location pin. The plug shall be inserted into the tube end. (Opposite to the Drive Unit). Idler: Idler is of high strength reinforced plastic, consisting of a centre shaft. The idler is mounted on the bracket by using a plastic lock. The metal sleeve inside the plastic lock provides bearing surface for the centre shaft, which rotates freely, providing smooth, quiet and long wearing operation.

Bottom rail: It is an aluminum extruded rail with a groove for fixing the fabric and power coated in white. Size: 21mm O.D.Alloy-HE9WP Weight-0.28 Kg/mtr. It is fixed to the bottom of the fabric and the purpose of it is, to keep the fabric in tension and straight. The fabric is fitted to the tube using plastic insert. The end caps of the tube are ABS. Operating chain: This is made of 4.5mm plastic beads molded on 2.2mm thick polyester chord. The pitch of the beads is 6mm. The chain drives the sprockets of the control unit to close and open the blind. The pitch of the chain corresponds to the sprocket in perfect match for trouble free operation.

Fixing brackets & clamps: These are used to fix the blind to the wall or ceiling. 'L' bracket is made of mild steel and zinc plated. The clamp is made up of spring steel of thickness O.7mm and zinc plated. The FABRIC shall be as per the following properties: Characteristics Values Composition 75% PVC, 25% Polyester Openess Factor 5% Weight per m2 465gsm/ ± 5 Thickness 0.65 mm Fire Resistance NFPA 701,BS5867 Part-2-Type-A Gaurantee Tearing Strength 4.5 Kgf Warp Bursting Strength 34Kgf Colour Fastness to light 8 Grade Colour 2

Supply and Installation of Vertical/Horizontal Blinds 100m width having the Control unit: The Control unit is made of high strength reinforced plastic of aprroved make Nova,MAC or Vista.

Repair for mechanism of roller, horizontal or vertical blinds, including of installation of any accessories required all complete inclusive of tools and labours, as per direction of engineer in-charge

Providing & Fixing Automated Blinds of required size Green Screen Roller Blinds as per approved equivalent having the DRIVE UNIT shall be of moulded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain pulley with ball chain and can be positioned at right side or left hand side of the Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a built in friction lock. The END PLUG shall be moulded of plastic with a steel location pin. The plug shall be inserted into the tube end. (Opposite to the Drive Unit).The SUPPORT BRACKETS shall be of coated steel & provided with covers and used in right hand or left hand positions differentiated by the acceptance of the of the rectangular drive unit support or the round idler plug pin. The ROLLER TUBE shall be of extruded aluminum with 38mm internal diameter & skin thickness of 1mm and shall incorporate a keyway integral with the tube to accommodate the spline.

Providing & Fixing Automated motor for Blinds with specification: Size-L1/L2- 564/577mm, Torque 6 NM, Speed 28 rpm, Rated, Current 0.5Amp, Rated Power 121 Watt, Rated Voltage 230 Volt, Rated Frequency 50HZ,Thermal Cutoff 4Minute, No of cables 3 Index Protection IP44,Average Running Noise 32-42 DBA

Providing & Fixing Automated (RF) remote for Blinds

Supply of Materials

Steel Name Plate with Engraved letter Size 10" x 3"

Brass Name Plate with Engraved letter size 18"X6"

Multi purpose lock round/Square of Godrej make only of size 50 x 40 x 50mm or as per requirement

Pad Lock Brass/ Stainless Steel of Godrej make only of size 50/40mm or as per requirement

Three Drawers Lock of Godrej & Hettich make only of size 580mm or as per requirement

Supply of Iron Door Chapka Kunda, Thickness: 2.6 - 3 mm X 100 mm

Supply of Hettich Onsys 4447i Soft Close Hinges for up to 25mm Thick Door 0 Crank Pack of 2 Set (4pcs.) (L-Bihari Kabja)

Supply of Hettich Onsys 4447i Soft Close Hinges for up to 25mm Thick Door 8 Crank Pack of 2 Set (4pcs.) (L-Bihari Kabja)

Supply of Neelkamal plastic chair with warranty 3 years (model: N507SS )

Supply of Steel A-Type Ladder 20 ft

Supply of Toilet Seat Cover For EWC ( Hindware, Cera or equivalent

Supply of Aluminium Sliding door lock

Supply of Toilet Seat Base Angle Castiron Bracket

Supply of Ball Cock Toilet Seat Cistern ( Cera, Hindware )

Supply of Ball Cck Water Cooler

Supply of L- Patti , 1",2",3",4"

Supply of 1-meter (1000mm) length, 32mm diameter stainless steel (SS) handle grade of steel (SS 304) and the finish( Adjustable )

Supply of Heavy duty brass gate valve 50 mm

Supply of Tinted glass 6 to 12mm thick for window & doors

Supply of Glass door handle Steel 8" to 12"

Supply of Fire door handle Size-39",35" & 33"

Supply of Glass Door lock

Supply of Glass Door Handle Steel 18"

Supply of Heavy duty brass 120kg door hinges

Supply of Glass door stopper

Supply of Teak Wooden Sturdy Coat Stand/Cloth Hanger with Two Drawers of Size : 90 x 33 x 48 cm, with proper polished finish inclusive of transportation and labour all complete as per direction of Engineer In-Charge.

Supply of Teak Wooden Coat Stand/Cloth Hanger - Pedestal Type of Size : 43 Inch, with proper polished finish inclusive of transportation and labour all complete as per direction of Engineer In-Charge.

Providing and Supplying S.S. Dustbins (Dry), Perforated matt finish, with all turned, well-formed and moulded edges at the bucket rim. Item to include sample approval from Architect/NHAI's Engineer.

Supply of powdered coated coloured planter made of stainless steel, non breakable with modern outlook and scratch proof coating having a protective ring at the base which prevents damage to the floor & water proof edges of required size including transportation, unpacking, labour all complete of approved make or as per direction of Engineer In-Charge:

Supply of Artificial Grass PVC Plastic Durable Stick Turf Mat of required shape and size including transportation, unpacking, labour all complete of approved make or as per direction of Engineer In-Charge:

Supply of Stainless Steel Ashcan Bin / Pushcan Bin/ Waste basket for dry waste like papers and office waste etc, having a protective ring at the base which prevents damage to the floor & fingerprint-proof finish with dent resistant heavy guage stainless steel of required size including transportation, unpacking, labour all complete of approved make or as per direction of Engineer In-Charge:

Miscellaneous Works

Repair of work station partion by providing wooden panel, pin board and MS plate replacement etc.complete .

Removing & Refixing of work station

Change of Chair Uphostry (Auditorium) including removing & fixing

Change of uphostry with cushion including removing & fixing of exhisting chair for same place as per engineer incharge

Providing Memory Foam Back Rest Cushion-Ergonomically Designed for Lumbar Support Extra Wide Comfortable Pillow for Chair - Black inclusive of transportation and labour all complete as per direction of Engineer In-Charge.

Sofa Repair and upholstery per seat with Cusion, foam and apporved Fabric with repair of wood if any (excluding 40 density cusion seat) French sprit Polish one or more coat on old work.

Sofa Repair and upholstery per seat with Cusion, foam and apporved Fabrice with repair of wood if any (including 40 density cusion seat) French sprit Polish one or more coat on old work.( If cushion of ISI mark for 40density is not replaced Rs. 625/- will be deducted at the rate of per seat.)

Sofa Repair and upholstery per seat with Cusion, foam and apporved Leather with repair of wood if any French sprit Polish one or more coat on old work.

Repair and upholstery of wooden Chair including Foam, Cusion, Repair of wood, Fabrice & Nails/stepels

Dry cleaning of Sofa (Single Seater, Two Seater and Three Seater) as instruction of Engineer-in Charge.

Dry cleaning of all type chairs as instruction of Engineer-in Charge.

Providing and laying at site 12mm thick wooden laminated floor (AC'5) having an inbuilt 2mm compact sound bloc™ backing-class of use 32/23, wear resistance, impact resistance-IC 2, (as per EN 13329), Top surface having a MLC (Multi-Layer Composite) highly developed laminate, top surface treated with (Aluminium oxide) titan X™ on top of high density fiberboard substrate (density 910 kg/cum) specially developed core: having patented click system perfect fold™ joints to secure long lasting joint. The planks shall be placed on an under lay of 0.2mm thick alkali resistant polyethylene sheet. All as per manufacturer specification.

Providing and fixing at site 10mm to 12mm thick 100mm high laminated wooden skirting/trim all complete as engineer in charge.

Providing and fixing Carpet flooring using Carpet Tile of approved make, shade and pattern and of the following specification: High Cut – Low Loop Carpet tile, Premium Solution Dyed Tri-Lobal Nylon with Anti Stain Treatment, 1/10 gauge, Pile height should be 7.5mm Cut and 4.0mm Loop, total thickness 9.4mm, Tile size should be 609mm x 609mm, Secondary Back Commercial 100% Re-cyclable Duraback. Wear Warranty– product is warranted not to lose more than 10% pile fibre by weight in normal commercial use, 10 Year Warranty ASTM D2053-99. Grade 4 – Little or no change in color, Permanent Lifetime Protection – less than 3.5kv, Lifetime Stain Release System, ASTM E-648 Radiant Panel Class 1, All yarns used are Solution dyed to minimize use of water and exclude any effluent production, ISO 14001 and ISO 9001, CRI Green Label Plus Certified for Indoor Air Quality.

Providing and laying of 6mm thick PVC Vinyl flooring with foam backing, vinyl floor covering of size 1830 mm width x 13 metres length of weight 4400 g/m2 with wear layer thickness of 1 mm. Wear layer should be treated with Protocol (UV cured Polyurethane surface treatment) which facilitates ease of maintenance and eliminates the use of acrylic emulsions. Residual indentation should be less than 0.25mm & should conform to EN ISO 24343-1(EN 433). The product should have antibacterial properties. The product should also fulfill dimensional stability(EN ISO 23999(EN 434) & effect of furniture leg(EN 424). It should also be suitable for underfloor heating. The product should have excellent sound absorbtion of 24 db and excellent shock absorbent behaviour. The laid flooring shall confirm the fire rating Cfl-S1 class as per EN 13501-1.

Providing & fixing lacquered colour full glass 6mm for decorative interior walls, cabinets, patitions doors furnitures etc.

Supplying, fabricating and installing in position, acrylic solid surface made up of PMMA, MMA and Aluminum-tri-hydrate.. Product shall be chemically resistant, fully homogenous with no pores, extremely repellent to dirt/wear/tear and thus shall be simple and easy to clean. Density >/= 1650kg/m3, Impact resistance>/=25N. Product thickness shall be 6mm and comes in sheets of size: 750mm x 3600mm. Product applications include for counter top, wash basin and wall cladding to achieve highest level of hygiene standards and is available in multiple colours. (Korean)

Supplying, fabricating and installing in position, acrylic solid surface made up of PMMA, MMA and Aluminum-tri-hydrate.. Product shall be chemically resistant, fully homogenous with no pores, extremely repellent to dirt/wear/tear and thus shall be simple and easy to clean. Density >/= 1650kg/m3, Impact resistance>/=25N. Product thickness shall be 12mm and comes in sheets of size: 750mm x 3600mm. Product applications include for counter top, wash basin and wall cladding to achieve highest level of hygiene standards and is available in multiple colours. (Korean)

Providing and fixing 12 mm thick toughened glass of approved brand and manufacture, including providing and fixing top & bottom U-type fixing arrangement and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).

Providing and fixing Kimberly-Clark Aquarius Multi Fold Paper Towel Dispenser 70220 - M Fold Paper Towel Dispenser - 1 X White Paper Towel Dispenser (23.2 cm x 28 cm x 11.6 cm) of standard shape with bracket of the same materials with snap fittings of approved quality and colour

Providing and fixing ES81A Automatic Soap Dispenser Construction : Stainless Steel #316 Grade,Capacity : 1100 ML, Spray Amount : 2 ml, Sensing Range :1cm-8cm, Operation: Electrical or Battery (D size x 4).

Providing and Fixing of Cylindrical Brass Urinal pipe, for Sanitaryware of Size 18" all complete as per direction of Engineer In-Charge

Providing and Fixing of JKC Jaguar Type 32mm or 40mm Metropole Flush Repair Replacement Spare Parts Suitable for Jaguar Metropole Flush plunger for Toilet

Providing C.I. grating 150x150 mm (Square or Round as per requirement)

Providing JKC Marc Type Toilet Flush Valve Repair or Replacement kit 35mm x 1.5" Full Brass with Heavy Rubber Washer Seal or Gasket Ideal for Marc Type Flush Only

Providing Flush Tank Syphon Kit Full Set, Flushing Cistern Accessories, Standard Size Hindware, CERA or equivalent as per direction of Engineer In-Charge

Wash Basin Waste Coupling 32 mm

Wash Basin Waste Coupling 40 mm

Providing and Fixing of Godrej Locking Solutions and Systems 8171 Stella 6 Levers Steel Door Handle with Lock Set, Item Weight not less than 520 Grams which include: 1n lock, 1n striker plate, 1n handle set, 1n square shank, 2n keys, tools & labours all complete as per direction of Engineer In-Charge

Providing and Fixing of Cylindrical Godrej Locks 3792 Key Lock (Polished Finish) description: Single panel doors 32mm to 45mm thick, The lock can operated with key from outside, Backset : 60mm, Pin cylinder mechanism in brass,Automatic deadlocking,Item Weight not less than 600 Grams tools & labours, all complete as per direction of Engineer In-Charge

Providing and Fixing of Godrej C0712 Speed Hydraulic 60kg Door Closer, Maximum Closing Moment: 14Nm ; Other Dimensions: Door Weight : 60 kg, Door Panel Width : 1000 mm, Door Opening Angle : 180°,Warranty: 1 Year warranty from the date of invoice Material: Stainless Steel,Item Weight ‏ not less than‎ 1 kg 370 g, tools & labours,all complete as per direction of Engineer In-Charge

Providing and Fixing of Heavy Duty Antique Brass single leg hanging type Door Stopper 5"-125mm tools & labours,all complete as per direction of Engineer In-Charge

Providing and fixing Black Metal Keyboard Tray With Mouse tray and keyboard Channels Along with the hardware accessories Black Finish powder coated.

Providing and fixing of Regular Steel (Magnetic) Whiteboard for Office, Description:Resin Coated Steel Writing Surface, Alloy Aluminium (6063-T6 Frame), Paper Honeycomb Core & Virgin ABS Corners inclusive of transportation and labour all complete as per direction of Engineer in-Charge

Providing and fixing of Notice Pin-up Board/Pin-up Board/Soft Board/Bulletin Board/Pin-up Display Board for Office, Description: Softboard Core, Alloy Aluminium (6063-T6) Frame, Premium Flocked Fabric Cloth Surface & Virgin ABS Corners inclusive of transportation and labour all complete as per direction of Engineer in-Charge

Removing old fabric and refixing with new for fabric Notice Pin-up Board Upholestry Premium Flocked Fabric Cloth Surface inclusive of Material and labour all complete as per direction of Engineer in-Charge

Providing and Fixing of Laquered/ Coloured glass cladding for Vertical Piller & walls

Supply & placing in position 8 mm thick table glass of different required sizes with edges polished Make:-(Modiguard,Saint-Gobain or Ashahi.) with beveled edge

Removing existing hydraulic floor spring 12" and providing & fixing with new Hydraulic floor spring for Wooden / Glass door inclusive of material and labour all complete of make Ozone or Godrej or equivalent as per direction of Engineer in-Charge

Providing and fixing of Transparent or Sun Control films on Glass of Window/Doors or Partition of cabin all inclusive of material and labour all complete as per direction of Engineer In-Charge

Providing and fixing Emergency Exit / Fire Safety / Directional / Warning / Informational Sign Board of approved design, shape, size and material, including lettering, symbols, arrows, pictograms and messages in bilingual language (English & Hindi) as approved. The sign board shall be prepared with suitable printing, painting, vinyl pasting, reflective or photoluminescent finish as specified and fixed at the required location with screws, clamps, adhesive, brackets or other approved fixing arrangement complete. The item includes cost of all materials, fabrication, lettering, fixing accessories, transportation, labour, T&P and all incidental charges complete as per the direction of Engineer-in-Charge.

Providing & Fixing Name Plate Acrylic Base: 5 mm thick having Colour: Black / white / transparent / mirror gold as required Lettering: 3 mm raised acrylic letters Letter colour: Gold / silver / white / black Technology: Laser-cut letters and CNC/laser-cut base Edges: Smooth polished edges Finish: Gloss or matte Mounting: 4 SS decorative studs Outdoor use: UV-resistant material/print Water resistance: Yes Design: Customized as per approved artwork Artwork: CorelDRAW/AI/PDF/SVG Installation: Wall-mounted Warranty: Typically 1 year can be offered for workmanship; LED components should

Providing and fixing hooks, clips and chains Brass or Stainless steel for roof hanging of Name Plates

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 600 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing Stainless steel SS grade 304, curtain rod 25 mm dia with two brackets and finial for both ends of the curtain rod of requird size and shape fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete as per direction of Officer In-Charge.

Providing and fixing of 9mm thk Eco Board acoustic panel Synth of approved Anutone/Armstrong make and desire color to be fixed with necessary adhesives on existing partition /wall surfaces as per details provided in the drawings. Wooden level adjusters shall be used in case of any imperfections in the wall surface. Quoted rates shall include all operations as specified above at all heights and levels, making openings / cutouts for Electrical fixtures, HVAC etc including all tools and hardware all complete as per drawings and as directed by the Engineer-in-charge Composition : 100% PET (60% Recycled) with adhesive backing Category : Panels Dimensions : 1220x2440mm (+/-2mm) Thickness : 9mm (+/-7%) Sound Absorption : 0.70 NRC (No Air Gap)

Providing and fixing overhead rack and pinion door closer with optional back check and standard arm with two independent closing valves and latching speed adjustable by arm. All adjustment screws face fixed with slide plate. Max door weight 80kg for min 50mm door thickness, all as per instruction of the engineer in charge.( DORMA )

Repairing of Compactor

Supply and installation toilet cubicles of width and depth as per specifications/ site drawings. Cubicle height to be 2105 mm. Made from solid grade compact high pressure laminate as per IS:2046 manufactured under high specific pressure > 5 MPa and temperature >120oC with bunch of kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Top Head frame fixed to the wall on both sides using MS- wall brackets. The pilaster is slotted & affixed to the top head frame and secured from the top leaving all clear gap of 150mm and without any support from the bottom.The intermediate panel shall be anchored to the wall and pilasters. Panels have a black core that when machined, presents a distinctive black edge. Panel thickness 12 mm. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per drawing. (The cost of protecting Tile work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item)

HARDWARE & ACCESSORIES • H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection. Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section,Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. • Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated. • Conical shape Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt type. • Round Door knob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt type. • Rotating Thumb-turn locking system with privacy indicator made from Stainless steel grade 304. Surface finish to be matt type. • Stainless steel grade 304 screws. • Anti-rotation Nylon polyamide grade-6 expandable wall plugs. • The Work shall complete as per drawing , under supervision of engineer in charge and company experts Athena Lite- SS Series Cubicles- Std Sizes (W x D x H)- 900 mm x 1550 mm x 2105 mm, (Height is including 150 mm gap from bottom) Door Size- 600 mm

Round Door knob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt type.

Supply & installation of approved Slats made of pinewood E1 grade fiberboard, Veneer laminated finish, groove perforated slats L8-2 - (2mm grooves @ 8mm centers) / L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers) / L64-2 - (2mm grooves @ 64mm centers), back lined with black acoustical fleece, tongue groove edge for a seamless look, FR grade, of size 128x2440x16mm thick having base density 800Kg/m3, weight 12Kgs/m2 installed by using Aluminium core cross channel (CC18) and brackets. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is first fixed over Tufbloc partition provided (70mm thk as mentioned in sr. no.1) with suitable fasteners horizontally @ 400mm c/fasteners should be anchored upto studd SC48 behind. Slats of size 128x 2440x16mm is then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs both ways. • Core Variants - Pinewood E1 Fibreboard • Fire – Class 1 & P • Acoustics – NRC 0.45(system NRC) • Climate (OC RH) – 50, 70 • Light reflectance – color dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 1 • Strength, Load capacity (Kg) - Ball-Impact

Supply & installation of approved Slats made of pinewood E1 grade fiberboard, Melamine laminated finish, groove perforated slats L8-2 - (2mm grooves @ 8mm centers) / L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers) / L64-2 - (2mm grooves @ 64mm centers), back lined with black acoustical fleece, tongue-groove edge for a seamless look, of size 128x2440x16mm thick having base density 800Kg/m3, weight 12Kgs/m2 installed by using Aluminium core cross channel (CC18) and brackets. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is first fixed over Tufbloc partition provided (70mm thk as mentioned in sr. no.1) with suitable fasteners horizontally @ 400mm c/c.Fasteners should be anchored upto studd SC48 behind. Slats of size 128x2440x16mm is then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs bothways. • Core Variants - Pinewood E1 Fibreboard• Fire – Class 1 • Acoustics – NRC 0.45(system NRC) • Climate (OC RH) – 50, 70 • Light reflectance – color dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 1 • Strength, Load capacity (Kg) - Ball-Impact

Providing and fixing paneling with 6mm thick toughened glass with bevelled and polished edges of approved quality & make on 12mm thk wooden BWP Ply with mirror silicon adhesive etc., all complete at all heights as per manufacturers specifications including make it flush with adjoining wall paneling etc., also including the cost of making cutouts for electrical points with necessary materials, labour, scaffoldings, tools and tackles, plants etc., and as directed by the Engineer-in-charge. 12mm thick ply base/GI structural frame will be paid under respective items For Internal walls of Conference rooms, meeting rooms etc.,

Supply, & Installation of ZINC Titanium Interlocking wall cladding panels in preweathered Quartz Finish.The wall cladding system shall comprise of the following described VMZINC 1.0 mm interlocking panels of 300 mm width and max 2500 mm length.Exact length shall be decided after on site dimensions / GFC Drawings . Panels are formed with interlocking lap at panel edges and smooth, flat pan; designed to be field assembled in sequential installation by engaging edges of each panel to edge of adjacent panel. Panels are attached to supports/substrates using stainless screws located under edges of the panels The Panels Shall be Installed over the AL box Section of 25 mm X 50 mm usingf SS Screws of suitable size as recommended by manufacturer . Perforation :- Punched Perfroation shall be restircted to up to 30 % maximum

Providing and Fixing pristine white UPVC windows of high impact modified grade UPVC and must be colorfast and confirm to BS:7413 code,Bs 7412 code & BS EN12608 code & should pass test of 'Classification -P". for ignitability &' class-I' for surface spread of flame as per BS:476-Part 7. The profile shall be a hollow 3-chamber (across depth) profile with an outer wall of thickness of min.1.5mm. The outer profile dimension shall be 44X70mm for fixed window and 50X74mm for slider outer and slider sash shall be 68x48mm for sliding window and outer for casement windows of 44x70mm with sash of 53x70mm. Sizes of sections as per manufacturer but not less than theminimum size mentioned above All sections of the frame and sash shall be reinforced with GI section of min. width 2mm in accordance with the system suppliers recommendations as per design including hinges, stays, handles, etc. with Double Glass as per given specification. DGU, VLT=49%. SHGC =0.28 U value = 1.7 (DGU 6mm SKN 154 T (outside) + 12mm air gap +6mm clear T (inside) with weather seal in window is to be a double EPDM complete in all respect. There would be warrenty of 10 years on Profile & one year on hardwares. All complete as per specification and instruction of the Engineer-in-charge.

Urinal Port without Sensor( Cera ) wall mounted (610X380X360)MM

Providing and fixing wooden partition with Aluminium framing 50mm × 50mmX 1.8mm, finished with 12mm BWS marine plywood including 1mm Sunmica on both side of exposed surfaces, complete in all respects as approved by the Engineer-in-Charge, including all materials, labour, fittings, cutting, fixing, polishing/finishing, etc.

Removal and refixing of New motorized curtain in same position premium heavy-duty Auditorium/Opera Stage Curtain manufactured from high-density Flame-Retardant Acrylic Velour Fabric of approved shade and design, having a minimum fabric weight of 600–700 GSM, rich velvet pile finish, luxurious appearance, excellent draping characteristics, high opacity with superior light-blocking capability, enhanced sound absorption and acoustic performance, colorfastness to light and washing, shrink resistance, wrinkle resistance, anti-static properties, high tensile and tear strength, resistance to abrasion and repeated operation, and long service life. The fabric shall be uniformly woven, free from defects, and specially designed for professional auditorium, theater, opera house, convention center, and stage applications. The curtain shall provide excellent stage masking, glare reduction, and aesthetic enhancement while maintaining dimensional stability under varying environmental conditions. The work shall include supplying, stitching, tailoring, pleating, hemming, reinforcement with heavy-duty webbing, eyelets, hooks, and all necessary accessories, fixtures, fittings, hardware, supports, and installation materials required for complete and proper installation, including all labor, tools, tackles, transportation, loading, unloading, testing, and commissioning, complete in all respects as directed by the Engineer-in-Charge.

Removing & refixing new wall-to-wall auditorium carpet of approved shade and pattern, machine tufted, commercial heavy-duty quality, including underlay, adhesive, cutting, fitting around seats, steps, and all leads and lifts complete.Carpet Specification Wall-to-wall tufted carpet. Pile: 100% nylon or polypropylene. Pile height: 6–8 mm. Total thickness: 8–10 mm. Fire-retardant and anti-static properties. Backing: Action back or synthetic jute backing. Fixed over approved underlay with adhesive. Colour and pattern as approved by the Engineer-in-Charge

Providing and fixing SS 304 Stainless Steel Sliding Gate fabricated from SS square/rectangular pipes as per approved design, including cutting, welding, grinding, mirror/matt finish polishing, complete with heavy-duty sliding track, rollers, guide rollers, stopper, handle, lock, anchor fasteners, all necessary accessories, transportation, labour, installation, and testing complete.

WPC Decking - Supply & fixing of Krraft Mammoth WPC Co extruded with round hole profile decking of the size 146mm x 24mm x 2400 mm of composition HDPE 30% Wood Powder of Poplar 60% Other additives 10% having density 1.3g/cum, tensil strength >22 Mpa flexural strength 28.00 Mpa having impact strength of 3.5 Kj/m2 and is mothproof. Installed on aluminium frame of 25mm x 50mm in filled with timber placed at a distance of 450mm. Installation done by metal clips.

Providing & Fixing rate Hilty fastener with chemical 12mmX200MM

Providing and fixing EPDM ( Ethylene Propylene Diene Monomer) rubber gasket to existing aluminium windows Inside or outside including removal of old gasket, supply of new gasket, labour, scaffolding/jhula, and all incidental charges complete.

Providing & Fixing 12mm Toughened glass ( Sliding door etc.) with Profile, fitting & Installation,

Providing and fixing main entrance automatic sliding glass door, comprising 12 mm thick clear toughened safety glass, DORMA/Dormakaba automatic sliding door operator of suitable capacity, motion/radar sensor, infrared safety sensor/light barrier, aluminium/stainless-steel glass clamping profiles, floor guides, end stops, program switch, EM lock where required, SS/approved patch and connecting fittings, track, rollers, control unit, wiring, necessary accessories, installation, testing and commissioning, complete as per manufacturer's specifications and Engineer-in-Charge's instructions

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Including Door handle, lock and stopper etc. ).

Providing & fixing TOSHI Automatic Sensor Tap TOSHI T-718 Eco Chrome-plated brass body Wash-basin mounted 150 mm adjustable sensor range 220V AC / 6V DC or 4×AA batteries

Providing & fixing JAQUAR Opal Prime SNR-15019PM\ Automatic infrared sensor Deck/table mounted wash-basin tap Chrome finish

Common Carpet for Auditoriums & Large Venues. 1.1. Nylon Wall-to-Wall Broadloom Carpet Colour & Quality as per Engineer Incharge

Vaccum Cleaning with proper dry cleaning with required chemical and detergent of Carpet Tiles/ Floor

Dismantle and Disposal

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling W.C. of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Dismantling 15 to 40 mm dia GI/PPR/CPVC pipe (Concealed or exposed on wall) including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling tile work in floors and Walls laid in cement mortar including stacking material within 50 metres lead.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, including all lifts involved.

Manpower

Supply of Manpower:

Part A Amount (Civil Works)

Part B - Electrical Works

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make Polycab, Havells

Rewiring for light point/ fan point/ exhaust fan point/call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS/HFFR PVC insulated copper conductorsingle core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling asrequired.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Make Havells, Schneider, ABB

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. Make Havells, Schneider, ABB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make Havells, L & T, Schneider, ABB

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make Havells, L & T, Schneider, ABB

LED Down lighter (SMD Type) (System lumenefficacy >135lm/Watt) Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round /square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%. Make Philips, Crompton

LED Panel light 2x2 ft. (System lumen efficacy ≥120 <135 lm/Watt) Supplying, Installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%. Make Philips, Crompton

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded. Must be of 1U height with clear label holders and white label with the panel.24 Ports Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required. Make D link

Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of CAT6 Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility and interoperability etc. complete as required. Make D link

Supplying, Installation, Testing and commissioning of RJ45 Connector for CAT 6/6A Cables. RJ45 modular plug supports 4 twisted pairs, 8 positions, 8 connectors. Housing: PC, UL94V-2, transparent color, Use for 24- 26 AWG stranded wires etc. complete as required. Make D link

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force: 11.5Kg etc. complete as required. Make D link

Supplying, installation, Testing and commissioning of 24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port supporting 802.3at PoE+ min. Make D link

PVC Exhaust Fans

Axial Air High-Speed Plastic Exhaust/Ventilation Fan (150 mm/6 Inches). Make : Usha, Bajaj, crompton

Exhaust Fan 250mm (10 inches) for Bathroom/ Kitchen. Power rating 18W, Installation-Square Cut (285mm), Low Noise, Easy to Clean, 100% Copper Motor , Usha, Bajaj, crompton

Corded grey Metal exhaust fan 230 mm (9‑Inch) Usha, Bajaj, crompton

SITC of Blue Star 80 L Storage Water Cooler SDLX6080B Features: Brand Name :Blue Star Refrigerant :R 134 a Capacity : 80 L Type of Product :Water Cooler Model No :SDLX6080B Cooling Capacity: 60 Litre per Hour Energy Consumption Rating: 5 Stars

Supply, installation, testing and commissioning of Floor Standing Water Dispenser with Refrigerator Make: Blue Star,voltas Type / Style: Floor standing water dispenser with inbuilt efrigerator. Number of Taps: 3 Nos. (Hot, Cold & Normal) Tap Type: Push type taps for enhanced durability Hot Water Tap: Provided with child-lock safety feature Cold Water Tank: SS 304 food-grade stainless steel for improved hygiene and corrosion resistance Refrigerator Capacity: 15 Litres, Cooling Capacity: 2.5 Litres per hour Heating Capacity: 5 Litres per hour, Operation: Quiet operation, compact design, Construction & Features: Body Material: ABS (Acrylonitrile Butadiene Styrene) Front Panel & Taps: Long-lasting plastic construction Drip Tray: Removable type for easy cleaning, Sensors: Bimetal sensors for protection against overheating Refrigerant: Eco-friendly R-134a, General Details: Colour: Grey, Dimensions (Approx.): 34.5 (D) × 31 (W) × 94 (H) cm, Weight (Approx.): 16.4 kg, Installation Type: Plug and play, Power Supply: AC mains, The item shall be manufactured in India, onforming to relevant BIS/ISI standards, and shall include transportation, installation, testing, commissioning, and all incidental charges.

SITC of RO PLANT Commercial (RO+UV+TDS+AUTO SHUT OFF) water purifier 100 Liter Per Hour Stainless steel Full Automatic with TDS Adjuster Includes: 1. Fully Stainless Steel Body With Two 300 GPD High Performance Copper Winded Booster Pump 2. Purification Technology : RO : Type : Electrical, Purification Stage :Stage 1: 5 microns inline PP filter || Stage 2: Granule Active Carbon Filter ||Stage 3: Block Active Carbon Filter || Stage 4: RO Membrane ||Stage 5: Post Carbon Filter 3.Purification : 100 Liter Per Hour , Two 300 Gpd Booster Pump , One Activated Carbon Filter, UV Purification system 4.1 Year Warranty on Booster Pump And SMPS

Supplying , Installation, Testing and Commissioning of Window type Air conditioners complete with copper power cable upto 3 Mtr, wireless Remote, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing, cooling, dehumidification, air circulation, R-32/R-410A /R-407B Green Refrigerant with Scroll / rotary compressor with min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB), antifreeze thermostat on the coil as a safety feature, complete with fixing including T&P & labour etc as required complete in all respect as specified of following capacity. Sound level of up to 50dB inside the room is acceptable. The unit shall be in confirmation with IS 1391 Part-I 2023 and CPWD Specification. The system shall be able to deliver 100% of the rated capacity upto 42 0C. The system shall be able to operate up to 50 0C (out door ambient temperature). Make Daikin, Blue star, Votas

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature). Make Daikin, Blue star, Votas

SITC of Hermaflo Room Heater, 2000W heating capacity, suitable for indoor use Dual Heat Settings: 1000W / 2000W Adjustable Thermostat for temperature control Thermal cut-out protection against overheating Fire-resistant PVC insulated wiring Power ON indicator light Rotary switch for power & heat control 1.8 meter power cord with 16A plug top Mounting Type: Floor Mount Special Feature: Adjustable Speed Dimensions: 31.5 × 22 × 12.5 cm (D×W×H). Make Usha, Crompton, Eveready, bajaj

Supply, Installation, Testing & Commissioning of 17 Inch Climatizer Desert Air Cooler suitable for indoor use, complete in all respects Fan Size: 17 Inch Climatizer Fan Blade for powerful air throw and uniform cooling Motor: 41 mm Heavy Duty Motor Air Flow Capacity: 4500 CFM (Cubic Feet Per Minute) Water Tank Capacity: 80 Litres Mobility: Heavy-duty castor wheels for easy movement Cooling Support: Built-in water dispenser, make crompton, Havells, Bajaj

SITC Smart Air Purifier suitable for residential / office indoor air purification Coverage Area: Up to 36 m² (Approx. 380 sq. ft.) imensions: 27.3 (D) × 48.6 (W) × 27.3 (H) cm Filtration Type: HEPA + Carbon Combi Filter (99.97% removal efficiency) contaminant Filtration:removes 99.97% Of Pollen, Allergies, Dust And Smoke, Hepa Filter, Ultra-Quiet And Low Energy Consumption Air Intake: 360° Air Suction Air Quality Monitoring: Real-time air quality monitoring with intelligent speed control.Filter life 15000 hrs Make philips, Honeywell, crusaders

Supplying, Installation, Testing and Commissioning Automatic Hand Dryer 235 x 205 x 265 mm (stainless steel) with wooden cleats and C.P. brass screws including cutting and making good the wall wherever required. (MAKE - CERA (Cat No. -B2220101)(MAKE-JAQUAR,CAT NO-HDR-SAP-M99ACS)(MAKE-TOTO,CODE-TYC122W)

Providing and Fixing 300mm Exhaust Fan having Fan sweep area: 300 MM ; Fan body dimension (Length x Width x Depth): 380MM x 380MM x 210MM Powder coated metallic finish, Guard: 29 Spokes, Noise level: (45 - 50) dB, Power consumption: 50 W, Rated voltage: 230 V, Rated frequency: 50 Hz, Motor type: Normal Speed, With bird guard to protect the fan in running condition; Rated Speed: 1350 revolution per minute, Warranty: 2 years on product of approved make Morphy Richards, Havells, Bajaj, orpat or equivalent only as per direction of Engineer In-Charge.

Providing and Fixing High Speed 400mm Wall Fan of approved make Havells, Crompton, Orpat or equivalent only as per direction of Engineer In-Charge.

Providing and Fixing High Speed 400mm Pedestal Fan of approved make Havells, Crompton, Orpat or equivalent only as per direction of Engineer In-Charge.

Waterproof 6 Watts LED Mirror down light complete with all accessories of Polycab/Havels/Philips/Surya or as per direction of Engineer In-Charge

Replacement of Urinal Sensor Battery (AA or AAA) of approved make DURACELL Only

Replacement of Urinal Sensor Battery CR-P2, 6V or 12V, Li-Ion of approved make DURACELL or Panasonic Only

Providing and fixing Wall Mounted Automatic Infrared Urinal Flush Valve Touchless of approved make Euronic or Jaquar or equivalent with approval of Engineer In-Charge

Providing and fixing Sensor Flushing Valve for Urinal Description :Sensor Flushing Valve for Urinal with Complete Kit (Battery Operated) Jaquar Code :SNR-CHR-51097 or equivalent with approval of Engineer In-Charge

Providing of Extension Chord Havells EcoStar 6 Amp, 4+1 Surge & Spike Guard with 4m Wire, Model ‎AHNKXXR004, Wattage ‎1440 Watts,Product Dimensions ‎26 x 13.5 x 4 cm; 300 Grams

Providing of Extension Chord 16 Amp, 3 output points with Surge & Spike Guard with 4m Wire

Providing & Fixing of Battery Box for urinal Sensor

Providing & Fixing of Urinal Sensor ( Hindware)

Providing and fixing of floor mounted outdoor type IP66 rating 10W LED garden diffusing typebollard light (light may be white or warm white) with driver.

Providing of 100W RGB Flood Light Down Chock with Remote Control, Outdoor Lights Waterproof, Ultra Bright with Aluminium Body.

Providing of 200-Watt LED Flood Light, BVP177 LED220 Frosted Glass Flood Light for Garden & Outdoor Lighting, Make Phillips, crompton.

LED flood light and street light driver ranging from 35W to 200 watt

Part B Amount (Electrical Works)

Credit Amount

The Buy-Back Rate for scrap material on as per kilogram basis (₹/Kg) & Each Item. The scrap generated from damaged/unserviceable furniture and other Electrical items shall be segregated into ferrous (iron/MS) and non-ferrous (aluminium) scrap. Payment shall be made based on the actual net weight/ Each item of scrap material handed over, as recorded through an approved weighing system. The quoted rate shall be inclusive of loading, handling, transportation and all other applicable charges,

Part C Amount (Credit)

Total Taxable Amount (Part A+B+C)

GST Amount

Final Tender Amount (Part A+B+C)

Abstract of Amount

Tentative Estimated Rates for Internal Painting of Existing Towers & Flats and miscellaneous civil works at NHAI Residential Enclave, Pocket:B-5, Sector-17, Dwarka, New Delhi-110078. -FINANCIAL BID

Agreement No.

Name of Agency

Date of Start

Date of Start (Actual)

Date of Completion

Date of Abstract

Item no.

For Repairing and Painting

White washing with lime to give an even shade : Old work (one or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Old work (one or more coats) over and including water thinnable priming coat with cement primer

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Finishing walls with textured interior paint of required shade : Old work (One or more coats) applied @ 1.82 ltr/10 sqm.

Finishing with Epoxy paint (one or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. Old work

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Repair to plaster of thickness 12mm to 20 mm in patches, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

Dismantling work in floors, skirting and walls laid in cement mortar including disposal. For thickness of tiles 10 mm to 25 mm

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of required size

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of Required size

Dismantling 15 to 40 mm dia pipe including stacking of dismantled pipes as per direction of Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

Providing and fixing shower set comprising one CP single lever concealed diverter JAQUAR Cat. No. 15075 / Parko cat. no.21003 / Kingston cat. no. KRA 004 .Bath tub spout with button attachment JAQUAR Cat. No. 463 / Parko cat. no. 21006A / Kingston cat. no. KRA-010 . shower with shower arm JAQUAR Cat. No. 477 & 489 / Parko cat. no. 2174 / Kingston cat. no. KRA 011. and telephonic shower JAQUAR Cat. No. 557 Parko cat. no. 2173 / Kingston cat. no. KRA 012 or as approved by the Engineer-in-Charge.

Providing and fixing shower enclosure HINDWARE Cat.no.506200/ PARRYWARE Cat .no.C8474/ CERA Cat.no.8831.overall size (H X L X W) 200 X 900 X 900mm finished with 6mm tempered clear glass complete with popup waste, door, SS door handle magnetic seal and shower panel HINDWARE Cat. no.500900/ PARRYWARE Cat.no.C841U/CERA Cat.no.8918. over all size (H x W) 1650 x 280mm finish with ABS body carring and making good the walls and floor all complete or as approved by the Engineer-in-Charge.

Providing and fixing C.P. brass bib taps long body (Jaquar Cat NO. 107 / Parko cat. No. 2106 / Kingston cat. No. KRA013 or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required. 15mm dia

Providing and fixing C.P. brass two way bib taps long body (Jaquar Cat NO. 15041 / Parko cat. No. 2106B / Kingston cat. No. KRA 013A or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required. 15mm dia

Providing and fixing 15mm C.P. brass angle valve with C.P. brass connection pipe (Jaquar Cat No. 053 & Cat No. 803 / Parko cat. no. 2119A/ Kingston cat. no. KRA 014 or as approved by the Engineer-in-Charge) union nuts complete with C.P. brass flange including cutting and making good the walls wherever required.

Providing and fixing CP brass shower with revolving ball joint Jaquar Cat No. 493 with shower arm Jaquar Cat No. 483 Parko cat. No. 2174 / Kingston cat. No. KRA011 or as approved by the Engineer-in-Charge.

Providing and fixing CP brass concealed stop cock reduced body Jaquar Cat No. 089 / Parko cat. No. 2117 / Kingston cat. No. AGR 306 or as approved by the Engineer-in-Charge.

Providing and fixing bath and shower arrangement comprising single lever concealed divertor for bath and shower system Jaquar Cat NO. 15075 / Parko cat. no. 21003 / Kingston cat. no. KRA 004 shower with shower arm Jaquar Cat No. 493 & 483 / Parko cat. no. 2174 / Kingston cat. no. KRA 011 with CP bath spout Jaquar Cat. No. 429 /PARK Cat.no.21006/KINGSTON Cat.no.KRA 015 or as approved by the Engineer-in-Charge.

Providing and Fixing CP brass single lever sink mixer with swinging spout wall mounted model (Jaquar Cat. NO. 15163 / Parko cat.no.21004/Kingston cat. no. KRA005 as approved by the Engineer-in- Charge).

Providing and fixing S.S. hinged grating, 6mm thick with frame as approved by the Engineer-in-Charge) including setting in floor with cement mortar 1:3.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia or 40 mm dia with length not less than 700 mm i/c PVC waste

Flexible pipe

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing gully trap P type 100x100 mm

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material as per direction of Engineer-in-charge.

In cement mortar

Qty. BF./CMB /P-

Total=

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and laying at site 12mm thick wooden laminated floor (AC'5) having an inbuilt 2mm compact sound bloc™ backing-class of use 32/23, wear resistance, impact resistance-IC 2, (as per EN 13329), Top surface having a MLC (Multi-Layer Composite) highly developed laminate, top surface treated with (Aluminium oxide) titan X™ on top of high density fiberboard substrate (density 910 kg/cum) specially developed core: having patented click system perfect fold™ joints to secure long lasting joint. The planks shall be placed on an under lay of 0.2mm thick alkali resistant polyethylene sheet. All as per manufacturer specification.

Providing and fixing at site 10mm to 12mm thick 100mm high laminated wooden skirting/trim all complete as engineer in charge.

For rain water and drainage

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

(i) Single socketed pipes

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Shoe (Plain)

160mm Shoe

110mm Shoe

Single tee with door

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50 x 50 x 50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing Slotted cowl (terminal guard)

110 mm dia

160 mm dia

For Wooden Finishing

French spirit polishing : One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Melamine polishing on wood work One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Wire Mesh Doors

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length inclusive of all complete as per direction of Engineer In-Charge.

Qty. BF./CMB /P-

Total=

Providing wood work in Shutter of doors, windows, and fixed in position with required adhesive and Screws of required dia & length including of all labour and Tools & Plants as per direction of Engineer In-Charge.

Qty. BF./CMB /P-

Total=

Providing and fixing of fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading including of applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Qty. BF./CMB /P-

Total=

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and polishing with french and melamine polishing matching with door etc. Complete as per direction of Engineer In-Charge. : 2nd class teak wood

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :

Qty. BF./CMB /P-

Total=

French spirit polishing : Two or more coats on new works including a coat of wood filler

Qty. BF./CMB /P-

Total=

Melamine polishing on wood work (one or more coat).

Qty. BF./CMB /P-

Total=

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Qty. BF./CMB /P-

Total=

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Qty. BF./CMB /P-

Total=

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Total=

Below 36.14%=

Total=

Qty. BF./CMB /P-

Total=

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Size of Tile 600x600 mm

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Extra Item Total=

Total=

RECOVERIES

2.5 % security deposit

Income Tax @ 2% on

GST @ 2% on

1% Labour cess on

1% Water Charges on

TOTAL

Gross amount

Less Recovery

Net Payable

Certified that :-

The work has been carried out as per CPWD specification & direction of Engineer-in-charge.

No labour complaint has been received till date with this office.

All necesarry recoveries have been made in this bill.

No T&P has been issued to the contractor.

No QCTA/CTE observations are pending.

Mandatory test sample has been sent, test awaited.

The contractor has engaged its Engineer on site of work.

Date of Measurement:

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Master Room

Deductions Door / window

Less Cupboard area

Guest Room

Deductions Door / window

Less Cupboard area

G/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Master Room

Deductions Door / window

Less Cupboard area

Guest Room

Deductions Door / window

Less Cupboard area

G/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

Total =

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Master Room

Deductions Door / window

Less Cupboard area

Guest Room

Deductions Door / window

Less Cupboard area

G/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

for 1st and 2nd floor

Kitchen

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Children Room

above cupboard

Deductions Door / window

Less Cupboard area

Bed Room

Deductions Door / window

Less Cupboard area

B/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Children Room

above cupboard

Deductions Door / window

Less Cupboard area

Bed Room

Deductions Door / window

Less Cupboard area

B/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

Total =

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Children Room

above cupboard

Deductions Door / window

Less Cupboard area

Bed Room

Deductions Door / window

Less Cupboard area

B/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

From 3rd to 8th floor

Kitchen

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

Flat No. A 501

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Flat No. A 501

MBR Ceiling

l/open

lobby ceiling

L/door

Dining area, ceiling

L/open

Ceiling

ceiling

Kitchen, ceiling

L/open

Entry ceiling

L/open

Room-2 , ceiling

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Flat No. A 501

MBR Ceiling

l/open

lobby ceiling

L/door

Dining area, ceiling

L/open

Ceiling

ceiling

Kitchen, ceiling

L/open

Entry ceiling

L/open

Room-2 , ceiling

Total=

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Flat No. A 501

MBR Ceiling

l/open

lobby ceiling

L/door

Dining area, ceiling

L/open

Ceiling

ceiling

Kitchen, ceiling

L/open

Entry ceiling

L/open

Room-2 , ceiling

CMB- /Page-

Date of Measurement:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

Flat No. A 501

entry door

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Flat No. A 501

MBR, Door

entry door

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Flat No. A 501

MBR, Door

entry door

CMB- /Page-

Date of Measurement:

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

stair area wall

wall (L=2.7+4/2=3.5m)

ceiling

Dining area, ceiling

L/open

l/stair

L/door

Entry ceiling

L/open

Kitchen ceiling

l/tiles

l/door

L/open

less window

less almirah

less door

MBR, ceiling

less window

near almirah, ceiling

less almirah

less door

less door toilet

less open

Servent room, ceiling

l/open

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

stair area wall

wall (L=2.7+4/2=3.5m)

ceiling

Dining area, ceiling

L/open

l/stair

L/door

Entry ceiling

L/open

Kitchen ceiling

l/tiles

l/door

L/open

less window

less almirah

less door

MBR, ceiling

less window

near almirah, ceiling

less almirah

less door

less door toilet

less open

Servent room, ceiling

l/open

CMB- /Page-

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

stair area wall

wall (L=2.7+4/2=3.5m)

ceiling

Dining area, ceiling

L/open

l/stair

L/door

Entry ceiling

L/open

Kitchen ceiling

l/tiles

l/door

L/open

less window

less almirah

less door

MBR, ceiling

less window

near almirah, ceiling

less almirah

less door

less door toilet

less open

Servent room, ceiling

l/open

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Dining area

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Dining area

CMB- /Page-