Repair of H no 8FM21 and 9J 50 in University of Health Sciences Rohtak

Amount

Dismantling cement conglomerate /terrazzo floors 25 mm to 50 mm thick including concrete base (HSR 8.25)

Dismantling cement conglomerate/ terrazzo-floors 25 mm to 50mm thick without concrete base (HSR 8.26)

Scraping cement plaster(HSR.8.32 c)

Cement concrete 1:8:16 with brick ballast 40 mm Nominal size in foundation and plinth.(HSR 10.26)

Cement concrete 1:2:4 with stone aggregate 20 mm Nominal size in foundation and plinth. (HSR. 10.41).

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR.11.7)

Conglomerate floor 40 mm thick cement concrete topping 1:2:4.(HSR.14.9)

Laying and fixing vitrified/ceramic anti skid tiles of any size of approved make in floor laid in any pattern as specified over a base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.93)

Laying and fixing vitrified/ceramic/glazed tiles of any size of approved make in skirting/dado, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.94)

Providing and fixing commercial type block board, plain lining, butt jointed, including wooden plugs (teak) placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall be payable extra)- (HSR 17.49) (b) 19 mm thick

Factory-manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. (non coniferous timber other teak, conforming to I.S. specification No.1003 kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. , complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (styles and rails of windows shutter shall be 75mm wide) (HSR 17.92)- Note 1 under chapter 17.18) (ii) 35 mm thick

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I. and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (HSR 17.93)- Note 1 under chapter 17.18) (a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:-(Jwala/Ujala make). (iii) 35 mm thick

Wrought iron and mild steel (using angles, flats, square bars, tee and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed staircase or parapet or any other type of railing, gates and tree guard etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Pressed steel sheet frames (chowkats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead Non-setting primer,of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete :- (HSR 18.34 )

(d) Door and window frame of size 114 mm x 50 mm with 35 mm wide double rebate

1.20 metres high fencing, with 1.65 metres posts, placed at every, 2.5 metres to 3 metres apart embedded in cement concrete blocks, and every tenth post, to be strutted, provided with 4 horizontal lines of G.I. barbed wire, weighing 9.34 kg. per 100 metres (minimum) and fixed with G.I. staples, tied to 6mm bar nib, with binding wire or by providing cut, including drilling holes, in the post complete (excluding the cost of posts, struts, earth work and concrete which is payable extra) (HSR 24.36)

N.S ITESM

Providing and fixing 3mm thick fiber sheet with necessary screw & J hook complete in all respect.(N.S)

Sh. Shiv Kumar