SPECIAL REPAIRS TO EM INSTALLATIONS AT PUMP HOUSE NO 01 AND 02 AT UDAIPUR MIL STN.

Amount

Dismantling fencing wire mesh (Chain Link Fencing) from Angle Iron posts or from RCC posts etc, complete all as specified and as directed by the EIC.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground any dia (Posts embedded in Concrete, brick work, ground masonry, etc), complete all as specified and as directed by the EIC.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and as directed by the EIC.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil.

Excavating in post holes (or similar holes) each n.exc0.5cum, getting out in hard/dense soil, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm thick, complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. exc 10 sq m on plan and n exc 1.5 m in depth and getting outn. exc. 1.5 m wide and n. exc. 1.5 m in depth & getting out in hard soil complete all as specified and as directed.

Material & Labour cement concrete in foundation filling incl mass concreting PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified.

Material and labour plain cement concrete 1:3:6 type C-2 (using 40 mm graded mechanically crushed stone aggregate) as in foundation filling and mass concrete complete all as specified.

Returning, filling in incl spreading leveling, watering and well ramming in layer n.exc 25cm in layer in soft/loose soil.

Removing excavated material not exc. 50 m and depositing in soft/hard soil, where directed .

Material & Labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter finished rough surfaces of concrete and flat, complete all as specified and as directed.

Material & Labour mild steel TMT bar 10 mm dia and over, cut to length, bent to shape required and binding with MS wire (annealed) not less than 0.9mm dia as in reinforcement to columns and line bars to hold/support the chain link fencing secured hodizontally, complete all as specified and as directed.

Material & Labour for rendering on fair faces of brick work or concrete surface of walls/columns 15mm thick in CM 1:4 finished even and smooth with out using extra cement complete all as specified and directed

Material & Labour for Preparing new surfaces of walls and applying three coats of whitewash complete all as specified and directed.

Supply and fixing MS angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) as in posts to fencing etc fixed in position conforming to Fe-410 (Gde E-250) (quality-A), complete all as specified and directed.

Supply and fixing rolled mild steel work in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming to fe-410-W (Gde-E-250) quality-A complete all as specified as directed.

Supply and fixing mild steel work as in flats to secure posts and struts in fencing/chain link fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified as directed.

S& F chain link fencing of mild steel galvanised dia of wire 3.15mm thick and mesh size 50 x 50mm including line wires, any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

Supply and fixed for galvanized 2 strand, steel barbed wire, 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with & provision of galvanized mild steel wire, staples or steel pins etc (each line of wire to be measured), complete all as specified.

Supply & Fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm long and dia of bolt 11 to 15mm complete all as specified and as directed.

Material and Labour for two coats of synthetic enamel paint on new steel surfaces over a coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified.

Material & labour 75mm thick PCC 1:4:8 type D2 using 40mm graded stone agg as in sub base etc., complete all as specified and as directed by the EIC.

Material & labour for Machine pressed precast concrete interlocking paver block rubberised moulded plain or coloured with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over 40mm thick river Sand cushioning layer etc complete all as specified and as directed by the EIC.

Taking down wooden chowkats or frames area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1 and reparing to broken jambs/reveals with plaster incl. white washing or distempering with putty as per exiting surface complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts, plastering of jambs/ reveals incl. white washing or distempering with putty and no separate items for these shall be paid).

Taking down wooden chowkats or frames area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1 and reparing to broken jambs/reveals with plaster incl. white washing or distempering with putty as per exiting surface complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts, plastering of jambs/ reveals incl. white washing or distempering with putty and no separate items for these shall be paid).

Demolition of cement concrete(unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Cutting holes exc. half brick but not exc one brick in brick walls built in CM or cement lime mortar & stone walls built in lime mortar for inserting holdfasts & making good dismantled portion in CM(1:3) or PCC(1:2:4) Type B-1 as required complete all as specified and directed.

M & L light coloured Non Skid ceramic jointless tiles of Size 300x300 of thickness 7 to 8mm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer with CM 1:4 complete all as specified and directed.

M&L for Non skid ceramic light shade tiles 605x605x7to8 mm thick, in floors etc. set and jointed with white cement and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer with CM 1:4 complete all as specified and directed.

M & L light coloured Glazed ceramic tiles in vertical serfaces 600 x 300 x 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing for tiles, complete all as specified and directed.

M & L for Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate), 25 mm thick in sub base of flooring etc, complete all as specified and directed.

M & L for 50 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid door/window/chowkats single door frame of size 45 x 75mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade),calcium carbonate 7natural fibers and no toxic additives fabricated with miter joint after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750kg/cum,screw withdrawal strength of 2200N(Face) & 1100N(Edge),Min compressive strength of 58 N/mm2,modulus of elasticity 900N/mm2 and resistance to spread of falme of class A category with property of being termite/borer proof,water/moisture prrof and fire proof& fixed in position with MS hold fast/lugs/SS dash fastners of required dia and lenmght complete all as as specified. Note:- MS Hold fast/lugsof SS dash fastners shall be paid seperately.

Supply and fixing PVC factory made shutter solid, PVC moulded prelam coloured on both side door shutter with particle board core 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design in framing at site as per specifications & drawings.

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

Supply and fixing 200 mm mild steel barrel tower bolts, ISI marked, stove enameled black with bright bolt and fixed, complete all as specified.

Supply and fixing mild steel pressed handles, oval type, enameled black 150mm long, complete all as specified.

Supply and fixing 300 mm mild steel sliding door bolts, ISI marked, stove enameled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified.

Supply & fixed steel windows box type ERW hollow 'P' section comprising double frame for and including gauged and glazed skelton shutter 30mm thick jointed internally with flat iron 25x3mm complete including hinges handle tower bolts, stops lugs,grill etc all as shown in drawing CEJZ TD -219 sheet 1/3 to 3/3 as applicable complete all as specified and directed. Note :- For the purpose of measurement & payment double shutter with frame and grill shall be considered as one unit. (ii) Glazing,wire mesh & painting shall be measured & paid separately.

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanised wire staples (to be fixed upto four storey of bldgs) complete all as specified and directed.

Supply & fixed for sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each and glazing with oil putty to steel window complete all as specified.

S & F Aluminium anodised or powder coated door, window, ventilator frame with one or more rebates and shutter sliding or casement windows as reqd. including jointing cleat, glazing clips with EDP gasket for fixing, rubber packing etc, complete all as specified and directed.

S&F 5.0 mm thick sheet glass, ordinary quality plain or tinted and glazing with rubber gasket in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

S&F in repair PVC low level flushing cistern of capacity 10 litres complete with siphon handle lever float valve and PVC bend incl connecting to ITWC/ ETWC and fixing on wall bracket complete all as specified.

S&F vitreous china wash basin white flat back size 550 x 400mm oval shape excluding taps, waste, chain & plug and porcelain stopper but including brackets or fixed to walls with anchor fastners all as specified.

S&F in repair vitreous china squatting pan white orissa pattern size 580 x 440mm with integral foot rests (excluding flushing cistern & flush pipe) with cast iron trap portion to match with the existing surface of floor all as specified.

S&F in repair 15mm bore pillar taps cast copper alloy chromium plated screwed down high pressure with or without lattered HOT or COLD with long screwed shanks and fly nuts screwed for iron pipes, all as spcified.

S&F in repair 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule all as specified

S&F 15mm bore tubes medium grade galvanized with all fittings such as Tees, elbows, unions, sockets, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length including taking down or up old GI tubing all as specified

S&F 20 mm bore tubes medium grade galvanized with all fittings such as Tees, elbows, unions, sockets, short, lengths, plus etc. and fixed complete to walls and ceilings or laid in floors of any length including taking down or up old GI tubing all as specified

S&F in repair 15mm bore angle valves/stop valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm all as specified

S&F in repair 100 mm/ 125mm dia mild steel chromium plated grating fixed on floor trap / nahni trap in Cement mortar 1:6 , all as specified

S&F in repair brass chromium plated soap tray/dish fixed with CP screws etc complete all as specified. )

S&F in repair rotational molded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position all as specified and directed.

S&F in repair PVC ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified

Supply & Fixed in repairs 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified.

Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick or concrete surface of any description, finished the surface even and smooth without using extra cement complete all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work, concrete surfaces in cement mortar 1:4 mixed with WPC as per manufacturer’s instructions, finished even and fair, complete all as specified. (Note : WPC shall be measured and paid separately)

Material and labour 5 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Supply only integral water proofing compound, complete all as specified.

Material & Labour for preparation of new/old plastered surfaces of wall/ceiling and applying 1 mm thick Birla/JK wall care white putty in two layers for neat and smooth finishing including preparation complete all as specified.

M&L for applying two coats of distempering with acrylic distemper white or coloured on prepared wall surfaces (putty) complete all as specified and directed.

Material and labour for preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceiling complete all as specified.

M&L for applying 1 mm thick Birla/JK wall care white putty in two layers white wall care putty on complete removal of existing treatment externl or internal walls complete all as specified and directed.

M&L two coat of exterior emulsion paint white or tinted on walls of prepared putty surfaces or old painted surfaces of bldg upto tripple storeys bldgs complete all as specified & directed. Note : Make :-Asian Paints (Brand-Ace)/ Berger paint (Brand -Walmasta) / Nerolac paint (Suraksha plus)

M&L one coat of exterior emulsion paint white or tinted on old treated walls of prepared putty surfaces of bldg upto tripple storeys bldgs complete all as specified & directed. Note : Make :-Asian Paints (Brand-Ace)/ Berger paint (Brand -Walmasta) / Nerolac paint (Suraksha plus)

M&L for two coat of synthetic enamel painting to wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer cpmplete all as specified and directed.

M&L for two coat of synthetic enamel painting to steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified.

Material and labour Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Material and labour Preparation of old painted steel or iron based surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Dismantling of any dia and size cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out complete all as specified and directed.

Supply & Fixed for 100 mm bore cast iron soil waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floors or in RCC tank roof complete all as specified.

Supply & Fixed for 75 mm bore cast iron soil waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

Supply & Fixed cast iron bends 100mm bore (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed cast iron bends 75 mm bore (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed 100 mm bore cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

Supply & Fixed 75 mm bore cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

Supply & Fixed 100mm bore cast iron bends with oval access doors (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed 75 mm bore cast iron bends with oval access doors (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed 100 mm bore cast iron Swan neck (or off-sets) 152 mm but n exc 305 mm in projection complete all as specified.

Supply & Fixed 100 mm bore cast iron cowls with cement joints complete all as specified.

Material and labour in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in slab supported on wall,beam, cantilevers and kitchen cooking platform complete all as specified.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Material & Labour for 18 mm thick south black Granite stone slabs (Jet/Telephonic black) on pillar/beam etc. machine cut laid over and including cement screed 15mm thick in CM 1:4 and jointed with grey cement slurry and pointed with coloured cement with admixture of pigment to match the shade of granite stone including cutting, polishing and half rounded at one corner complete all as specified and directed.

Labour only for grinding to granite for mounlding / bull nosing etc, complete all as directed.

Supplying and laying synthetic Rubber insulated mats 2.5 mm thick for voltage upto 11 kv for electrical purposeas per IS 15652-2006, (superseding IS 5424) suitable forelectrical shock safety of sizes 2m x 1m.

Dismantling/Taking out of old sign BOARD embeded in PCC and making good disturbed portiion size of BOARD 4' X 3' size with angle legs

M&L for road sign BOARD of size 1200X 900 mm made out with anle iron 40X40X6 mm covered one side with 2 mm Alluinium sheet with riveting on frame including Retro reflective sheet and 100 mm hight letters as required with 2 Nos legs of angle iron 40X40X6 mm of 2 mtr height embeded 60 cm in PCC 1:4:8 type D2 including 2 coat of synthetic enamed paint over a coat of red oxide primer making neccessary earth work etc complete

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by engineer in charge.

M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified (Make of cable: Kalinga/Havells/Anchor) for One light point / Fan/ bell point controlled by one switch.

(a) One light point controlled by one 5 Amps switch

(b) One Fan/exhaust fan point controlled by one 5 Amps switch

(c) One socket 3 Pin 5A pin socket oulet 5Amps on same board with cables 1.5 Sqmm size

(d) One socket 3 Pin 5A pin socket oulet 5Amps on indepndent board with cables 1.5 Sqmm size.

(e) One socket 3 Pin 15A pin socket outlet 15Amps on indepndent board with cables 4 Sqmm size

S&F switch piano flush type single pole one way 5/6 Amps.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd.

S&F lamp holder Angle / batton type insulated body with back plate and to be fixed on PVC block. Including dismantling old one.

S&F socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one. l

S&F of switch piano15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one.

S&F socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including old one

S&F ceiling rose surface tpe 3 terminals to be fixed on PVC block including dismantling old one.

S & F LED integrated batten tube light fittings 20 Watt 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed.

M/s Ajay kumar Garge

m/s sharma constructions