GE/BAS-59/2025-26 Provn of boundary wall and special repair to building no P-89 at Madhopur under GE Basoli.

Amount

Excavation in trenches n exc 1.5 m wide and nexc 1.5 m in depth for foundation or laying of UG cable/ pipe and getting out in any type of soil complete all as specified and directed.

M&L returning, filling and including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5mtr above the starting point, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graged crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed

M&L Reinforced cement concrete M-20 (Nominal mix) using 20mm graded crushed stone aggregates as in slabs/shelves, supported on walls, beam and columns in floors and in shelves and the like including necessay for work complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed.

S&F pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc incl 2 coat of synthetic enamel paint over a coat of red oxide complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats complete all as specified and directed.

S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc incl 2 coat of synthetic enamel paint over a coat of red oxide complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats complete all as specified and directed.

S&F pressed steel frames of size 75mm x 50mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc incl 2 coat of synthetic enamel paint over a coat of red oxide complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats complete all as specified and directed.

S&F18 to 20 mm thick solid PVC board prelaminated one side with decorative choice lamination weight not less than 10 kg/Sqm and other side balancing white fixed with screws to timber/angle iron frame work, complete all as specified and directed.

S&F Factory made single extruded WPC(wood polymer composite) solid door/ window /ceosetory windows & other Frames / chaukhat size 65 x105 mm with MS hold fast /lugs /SS dash fashteners dia and length complete as per direction of Engineer-in-Charge. (M.S hold fast/ lugs Or SS dash fasteners shall be paid separatly )

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 ,calcium carbonate and natural fibre and non toxic additives and resistance to spred of flame of Class A cateegory with property of being termite /borer proof ,water /moisture proof and fire retardant . WPC to be Laminated with PVC foil of minimum 14 microns thick of approval design pasted with hot melt adhesive on both faces of shutter and fixing with stainless butt hinges of required size with neccessary full body threated star headed counter sunk s.s screw shall all as per direction of enginner In charge.

S&F 2nd class hard wood 35mm thick factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F For Glazed and skelton shutters 35mm thick of 2nd class HW open rebated and prepared to receive glass or wire gauze etc. shutters divided in square with sash bars, size of members of shutters as specified in SSR Part-1, secton 8, clause 8.20(a) complete all as specified and directed.

S&F 30 mm thick Factory made 2nd class hard wood shutter with top panel Glazed and skeleton open rebated and prepared to receive glass, gauze, etc.(without sash bars) fitted with cut and mitred beds for securing glass, etc.; and bottom panel with panel of 9mm BWP commercial ply or 12 mm veneered particle board with comercial veneering on both faces. The sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and directed.

Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

M&L for 3 mm thick Frosted glass, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F in Butt hinges of stainless steel of size 100mm complete all as specified and directed.

Supply & fixing 100mm hasp and staple aluminium anodised, including bolt to hinge plate and fixed with screwscomplete all as specified and directed.

S&F for Stainless steel barrel tower bolt, 200 mm size complete all as specified and directed.

S&F for Stainless steel handle, cast type, 150 mm size complete all as specified and directed.

S&F Stainless steel,sliding door with hasp and size 300mm long with hasp, staples and fixing clips of sheet extruded section and fixing bolts of extruded section complete all as specified and directed.

Supply and fixing mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work complete all as specified and directed.

S&F Floor door stopper 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F continous (piano) hinges mild steel, 40mm width of flaps (when open), bright finish or electrogalvanised complete all as specified and directed.

S&F for drawer channel (soft close) 100% extension having strong and smooth operation for kitchen drawers complete all as specified and directed. Make: Godrej/hettich/Harrison

M&L Box type steel windows and ventilator comprising of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 150 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straininig bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth not otherwise described and applying two coat of synthetic enamel paint over and including of one coat of pink primer complete all as specified and directed.

M & L for applying two coats of 100 % Premium acrylic emulsion paint using hydraulic jet pressure machine incl priming coat of exterior primer applied @ 0.90 litre/10 Sqm,incl preparing new plasterd surfaces by sanding machine complete all as specified and directed.

M&L for Preparation of new plastered/concrete surfaces of walls and applying two coats of cement based paint over and including one coat of primer complete all as specified and directed.

S&F Framed work such as doors or gates etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including two coat of synthetic enamel paint and one coat of red oxide primer complete all as specified and directed.

S&F mild Steel work, angles, bars, flats etc as in supports for posts and struts in fencing, gate etc including cutting tops to shape etc as dirceted, drilling holes, notching for wire, flat iron fillets (For securing wire mesh etc) including all necessary drilling, bolting or riveting and similar work complete all as specified and directed.

Material and labour for plain cement concrete type B-1 1:2:4 (20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs ,water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for APP modified roof treatment over existing accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufacture by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3.0mm thick APP modified water proofing membrane weighing not less than 3.50 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. NOTE :- MOU to be submitted by the contractor beore starting of work with the authorised applicator by the OEM of APP membrane duly recommended by Engineer-in-charge

M&L for cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate), top surface of plain concrete padding shall be finished even & fair w/o using extra cement complete all as specified and directed.

M&L for 40mm thick brick tiles laid on cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement including dismantling roof tiles of any description, complete all as specified and directed.

All as per item No above, but except brick tile complete all as specified and directed

M & L for cleaning, breaking, loose concrete, cleaning of reinforcement and filling plain cement concrete 1:1 1/2 :3 type B0 using 12.5mm graded aggregate at places as per direction by E-in-Charge (the cost of scafoldings, formworks deemed to be included in the item)

Taking down eaves gutters and rainwater pipes 100 mm dia (any size or pattern), including all fitting, head, shoes, bend, swan-nacks etc. including cleaning or refixing or removal to store complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls/in trenches complete all as specified and directed .

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls/in trenches complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 110 mm bore in repair complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 110 mm bore with access door in repair complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 75 mm bore with access door in repair complete all as specified and directed.

S&F in repairs for 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Supply and fixing in repair PVC(SWR), junction single, (single 'T'/Y) with access door equal or unequal for 110 mm bore, complete all as specified and directed.

Supply and fixing in repair PVC(SWR), junction single, (single 'T'/Y) with access door equal or unequal for 75 mm bore, complete all as specified and directed.

M&L PVC (SWR) Branch Pieces Single Y Equal or unequal, 110mm complete all as specified and directed

M&L PVC (SWR) Branch Pieces Single Y Equal or unequal, 75mm complete all as specified and directed

S&F PVC (SWR) reducer 110mm bore complete all as specified and directed.

S&F PVC (SWR) Vent cowl 75 mm bore in repair..complete all as specified and directed.

S&F in repair/new PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M&L for Rotational moulded polyethylene water storage tank 3 layer white colour water tank, non- toxic effect, algea formation protection (made from Virgin grade of polyetylene material which is duly stablized with anti-oxidentPlastic) of capacity 500 litres, (cylindrical vertical tanks with closed top,specific wt shall be 25 gm/ltr), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc including taking down existing tank complete all as specified and directed.

S&F in repair 20 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe of 20mm bore complete all as specified and directed.

S&F in repair 15mm bore chromium plated cast copper alloy bib taps fancy type long body with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule all complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repair Vitreous China squatting pan of orissa pattern, size 580x440mm white with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern (including fixing of flush pipe) including provision of cement concrete bedding, in repair complete all as specified and directed.

S&F in repair PVC valveless,syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and directed

S&F of 15mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 15mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

Refixing of 15mm dia bore steel water GI tubes medium grade with all new fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 15mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed.

S&F of 20mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 20mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

Refixing of 20mm dia bore steel water GI tubes medium grade with all new fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 15mm bore steel water tubing and connections including cutting/ chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

Demolition of plain cement concrete in ground floors or above ground floor and paving n.exc 15 cm thickness (Below or above ground level) complete all as specified and directed

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

M&L for hard core of broken stone or boulders, gauge n exc. 63mm depositing spread and lavelled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified and directed

M&L for 75mm thick PCC 1:3:6, type C-2 using 40mm graded crushed stone aggregates as in sub bases of floors and pavings complete all as specified and directed.

M&L for Sand filling/cushioning as in floor, foundation including watering and consolidation complete all as specified and directed.

M&L machine pressed precast concrete interlocking colour paver block any shape and size confirming to IS 15658- 2006 0f 60mm thickness with grey cement and pigment, M-35 grade complete all as specified and directed.

M&L for demolition of Concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for demolition of Concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graged crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type b-2 (using 40 mm graged crushed stone aggregate) as in surface channel and drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 (using 40 mm graged crushed stone aggregate) as in foundation filling and mass concrete (sunken floors etc) complete all as specified and directed

M&L for (a) Rendering 15mm thick plaster in cement sand mortar (1:4) mixed with water proofing compound (confirm to IS-2645-Specification for integral cement water proofing compound) as approved as per manufacturer instruction, shall be applied both on floor and side walls. The surface shall be cured and allowed to dry, all the joints of pipe shall be sealed properly as per instruction of agency who is carying out water proofing treatment. (b) Apply a layer of 3mm thick APP modified membrane over a coat of oil bound bitumen primer @ 0.30 liter/Sqm on floor as well as on side wall as per manufacturer's instruction of make/Manufacurer is over, sunkun portion shall be kept full of water for atleast one week to check that no seepage is seen from the external surfaces complete all as specified and directed. NOTE :- MOU to be submitted by the contractor beore starting of work with the authorised applicator by the OEM of APP membrane duly recommended by Engineer-in-charge

M&L for cement concrete type B-0 1:2:4 using (12.5 mm graded stone aggregates) 25 mm thick in flooring complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for 10mm thick rendering/screeding on fair faces of brick/concrete surfaces in cement mortar 1:4 and finished even and fair for receiving tiles complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x250mmx7mm/450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface. (sample as approved & kept in GE's sample room) complete all as specified and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface. (sample as approved & kept in GE's sample room) complete all as specified and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface. (sample as approved & kept in GE's sample room) complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, preparation of new plastered surfaces of walls and applying 1mm thick wall care putty, one coat of primer and two coat oil emulsion distemper on walls complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for rendering or plastering work 10mm thick in CM 1:3 in fascia / edging / ceiling of Chajjas, roof projections etc, taking out peeled off plaster / concrete and making the line in true shape and finishing the surface without using extra cement. complete all as specified and directed.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps ( tread/ riser) in single piece , jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 complete all as specified and directed.

M&L 20mm thick work (table rubbed and polished ) for wall lining (venerring to wall ) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 complete all as specified and directed.

M&L for Pre-polished Machine cut kota slab fooring as in step and riser of stair case 16 to 18mm thickness over cement screed base laid and jointed with gray cement slurry mixed with pigment to matches the shade of the slab including rubbing and polishing,and 20mm thick screed bed or bedding layer of mortar in cm 1:6 for laying floor finishes complete all as specified and directed.

M&L for Pre-polished Machine cut kota slab skirting 16 to 18mm thickness over cement screed base laid and jointed with gray cement slurry mixed with pigment to matches the shade of the slab including rubbing and polishing and taking down cement plaster on brick or concrete surface including racking out joints hacking for key scrubbing down with water etc and Rendering 10 mm thick in CM 1:4 as for backing coat of wall tiles complete all as specified and directed.

Rounding/moulding to edges of stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooding platform and other similar situations etc complete all as specified and directed.

Taking down cement plaster on brick or concrete surface of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

S&F in reapirs Stop valve/ Angle valve cast copper alloy (ISI Marked) chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F in repair Stop valve concealed cast copper alloy (ISI Markd) fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F in repair chromium plated shower roses with or without swivel joints 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F in repair Chromium plated Wash hand basin Mixer (Swan Neck) with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm, complete all as specified and directed.

S&F in repair brass Chromium plated sink mixer with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm, complete all as specified and directed.

S & F in repairs Vitreous china wash basin, under sunk size 450 x 300 mm including waste pipe ,fixed in slab and matching with the granite level and 32 mm dia PVC waste pipe fixed in repair including waste copling 32mm size full thread , complete all as specified and directed

S&F in repair stainless steel kitchen plate rack of size 750 x 900 mm made out of 1.00mm thick sheet of approved make fixed with mild steel screw complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, washers and wastes; including fixing in slab making the in level of granite finishing and connecting union to pipe, overall size 915x460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quions, arches, pillar complete all as specified and directed

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:6, complete all as specified and directed

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:4, complete all as specified and directed

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or conrete surfaces finishing the surface even and smooth without using extra cement mixed with liquid water proofing compound complete all as specified and directed

M&L for Cement concrete type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair incl making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed.

M&L for rendering 5 mm thick in CM (1:3) finished surface even and smooth w/o using extra cement in ceiling. and applying three coats of white wash on ceiling complete all as specified and directed

Supply only Liquid Water Proofing Compound. complete all as specified and directed

M&L for concrete bed to drain pipes laid in trenches incl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) for 150mm bore of pipe complete all as specified and directed.

M&L cutting into existing manholes (150mm dia pipe) for connecting new drains,making good to pipe and rendering, cutting out existing benching for and forming branch cahnnel (1/2 round or 3/4 section) incement concrete 1:2:4 type B-1 smooth finished and reforming benching as required completeall as specified and directed.

M&L for Reinforced concrete pipes150mm, class NP-2, laid and jointed complete with collars bed complete incl testing all as specified (Concrete to be measured and paid for separately) complete all as specified and directed.

M&L precast Reinforced cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregates) as in man hole covers set in cement mortar 1:6 all as specified and directed incl necessary form work. Note: Steel reinforcement shall be measured and paid for separately under respective items

Taking down copper/aluminum point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as per specified and directed.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC concealed conduit having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked for switches, including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained. (Ph-Red, N-Black, Half -Yellow, Earth- Green)

All as per item No 121 but for one 3 pin 5 Amp socket outlet on independent board complete all as per specified and directed.

All as per srl item No 121 above but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

M & L for point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC concealed conduit having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet, including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed. Note: (a) Insulation test of point wiring (b) colour coding is to be maintained. (Ph-Red, N-Black,Earth- Green)

S & F for switch piano flush type one way 5 amps SP complete all as specified and directed. Make: Havells (REO) or technocommerically equivalent make of cona/SSK.

S & F for switch piano flush type one way 15 amps SP complete all as specified and directed. Make: Havells (REO) or technocommerically equivalent make of cona/SSK.

S & F socket outlet 3 pin 5 amps flush type complete all as specified and directed. Make : Havells (REO) or technocommerically equivalent make of cona/SSK.

S & F socket outlet 2 in one 5 pin 15 amps flush type 230volt complete all as specified and directed. Make : Havells (REO) or technocommerically equivalent make of cona /SSK.

Supply and fix bell push flush type 5 Amps complete all as specified and directed, make : Havells (Reo) or technocommercially equivalent in Cona/SSK .

S&F in repair/replacement bell ding dong type, complete all as specified and directed .

S&F sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 4.0 Sqmm drawing including PVC non metallic rigid conduit of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 4.0 Sqmm as a earth continuity conductor(green colour) in and including in non metallic rigid PVC conduit, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :(i) Two run of 4.00 sqmm single core (FRLS) PVC insulated copper conductor cable one run of 4.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

S & F lamp holderbatton holder/Angle holder insulated body (metal ring) with bakelite type with back plate suitable for batten fitting complete all as specified and directed.

S&F ceiling rose surface 65x50mm three terminal with bakelite back plate complete all as specified and directed.

Supply and fixing ceiling fan regulator electronic type 5 stage speed variation,socket type is size, ISI marked complete all as specified and directed. Make : Havells (REO) or technocommerically equivalent make of cona /SSK.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose of make : Philips,cat part No :BN170C LED20S-6500 PSU L120 /Havells,Cat part no : LUMILINEPLUSNEOBS20WLED865SPCSSIND/Crompton, cat part no : CCS-100-20-65-HL2-DP-NWH/ Orient, cat part no :LBLN-20-C-SQ-AL complete all as specified and directed

Supply and fixing of Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base of make : Havells, cat part no : LHFOAJE1TZ1I060/ Philips, model no : 30978 complete all as specified and directed.

M & L for providing/cutting the round /square hole on the wall and supply and fixing propeller type AC ventilating fans (Metalic body) Single phase, 230 volts 250 mm sweep including grouting and fixing the ragged bolts in wall for exhaust fan and louver shutter on the exhaust side wall (outer surface of the wall ) and connecting PVC insulated three core 1.5 SQMM copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enemel paint 2.0 cm high. Make of Exhaust fan - Havells, model no : Ventil Air DS Green /Standard, model no :Refresh air - SPS/Khaitan, model No: Eurocap complete all as specified and directed.

M & L for providing/cutting the round /square hole on the wall and supply and fixing propeller type AC ventilating fans (Metalic body) Single phase, 230 volts 300 mm sweep including grouting and fixing the ragged bolts in wall for exhaust fan and louver shutter on the exhaust side wall (outer surface of the wall) and connecting PVC insulated three core 1.5 SQMM copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enemel paint 2.0 cm high. Make of Exhaust fan - Havells, model no : Ventil Air DS Green /Standard, model no :Refresh air - SPS/Khaitan, model No: Eurocap complete all as specified and directed.

S&F of LED Bldg security lights of 35 Watt, 230 V having pressure die cast aluminium housing with system lumens efficacy≥100 lumen/W IP65 protection, IK07 rating, inbuilt electronic driver with PF>0.95 incl Gl bracket of suitable dia bend to shape and fixed to wall by means of clamps or nuts bolts and connecting up with three core twisted flexible copper conductor cable . Make of street light fitting - Bajaj, cat part no :ENXT P 35L WH PO PC SD/Havells ,cat part no :ENDURASUNDOWNSL35WLED765PASYBOPC/Wipro ,cat part no : LR08-501-XXX-57-XX/Crompton ,cat part no : TRP-400-35-57-SL-LM-NSR including taking out old /unsv securtiy light any type and rating complete all as specified and directed.

S&F MCB SP 6-32 Amps with 10KA breaking capacity of 'B' series in distribution board complete all as per specified and directed.

S&F in replacement MCBs single pole and neutral (SPN)/isolator 32 Amps with 10 KA breaking capacity of 'B' series in distribution boards all as specified and directed.

M&L for SPN MCB DB 8 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 43 and IK 09 rating having fully insulated copper busbar, neutral bar, earth bar and cable ties for cable management including polyuthrene gasket complete fixed flush in wall including cutting chases on wall for taking out old DB and fixing of new DB and making good disturbed surface of wall with cement mortar and finishes to match exisiting surface complete all as specified and directed.

Supply and fixing LED light fitting mirror type Surface mounting General Purpose LED Battens in Extruded Aluminium housing with suite variety of application areas with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete of Make: Havells, cat part no: LUMILINEPLUSBS10WLED865SPCSSIND/Crompton, cat part no : TCS-108-10-65-SL-DP-NWH/of make Orient, cat part no: LBLN-10-C-SQ complete all as specified and directed.

Removing existing unserviceable DBs along with its enclousers old wiring in between DBs /main switch /meter etc and supply and fix factory made fabricated sheet metal enclouser wall mounting type DB of size 1 mtr x 1 mtr x 0.25mtr with 2mm thick CRCA sheet and applying two coats of synthetic enamal paint over one coat of red oxide zincchrome primer suitable to accomodate and comprising of following: (a) Fixing Existing Electric energy meter 0-40 amps -05 nos (b) One number MCCB VTPN DB 4 Way double door with one incoming MCCB 63 amps(TP), 16 KA. (c) MCB SP 32 amps -04 Nos . (d) MCB SP 16 amps -01 No (e) Blanks plate as per requirement . (f) Wiring with PVC insulated unsheathed ISI marked 6 sqmm FRLS copper conductor connected in between DB's SP to electric meter etc complete all as specified and directed . (g) Providinfg of glass for energy meter reading purpose.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of SSR Part-I (2009) including filling of charcoal dust, common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthling wire)

JP AND CO. (BID ID -3429576)

HARI OM ENTERPRISES (BID ID -3428796)

M/S SATYA SAI CONSTRUCTION (BID ID -3429969)

Substantial Const. Co. (BID ID -3429993)

Standard engineers (BID ID -3430209)

M/S SURINDER KUMAR MAHAJAN (BID ID -3429886)