Construction work of New Building for JSHEC, JCSTI, JSFDA and others in the campus of Jharkhand University of Technology, Ranchi

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earthwork in hard soil as per specification and direction of E/I. (vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 112mm thick reinforced designation 100A brickwork fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including the cost of screening carriage of material scaffolfing raking out joint to 15mm depth curing taxes and royalty (but excluding the cost of reinforcement ) all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings)

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Weather shade, Chajjas, corbels etc., including edge

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

Providing Tor steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

(a) 10mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

(b) 12mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

(c) 16mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

Providing Tor steel reinforcement of 20mm, 25mm, 28 mm, 32mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I.

Providing 12 mm cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curring, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. : With commercial grade colour 15X15cm Tiles.

Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Extra of plaster work over exterior surface for each consecutive floor above above first floor including cost of scaffolding etc. All complete as per direction of E/I.

Making 6X6mm grooves in plaster surface over walls truely horizontal or vertical as specified at regular intervals, at all heights including cleaning, finishing, scaffolding and curring with all leads and lift of water all complete as per building specification and direction of E/I.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including preparing the surface after cleaning removing dirt,scales grease including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flextble material brush, roller or spray for water proofing coating meteranufacturer Specifications with following steps :-(a)surface preparation .-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing (loose paint / coating, and cement laitance by cleaning with compressed air water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be done with non shrink expanding admixture of Sika India Pvt.L.td.) MYK Schomberg / Dr Fixiti/ Fosroc or equivallent. Providing and reparing of all Corner and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150Mrn X 150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic pc?' lymer of Sika/ Fosroc/MYK Schomberg/Dr 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent.,Befor 'Chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar-including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.(b)lst Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitiot.is material on surface saturated dry roof and inside wall of Parapet.Wall upto 600 mm by brush or roller . After 1st coat of application , 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shOUld be applied @1.50 kg/sqmt/coat. For the purpose of measurer-11609-1'e entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified read to use, flexible cementtiOus material right angle to the 1st. coat over the glass fibre laid surface: 2nd coat-,should be applied @ 0.7 sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing Brand:- Sika Topseal 109hi / Fosroc Brushbond RFXI Dr. Fixit Pidiffin 2K / MYK Aquafin TG . Product Performance - Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder - Density 1.6 kg/I (mixed density) at +27°C Tensile Strength -2 Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Siren th -2 f\l/mm2 concrete failure Accordin' to ISO4624) Slant-Shear Bond Strength -4 Nimm2 (According to FIP 5.15) Elongation at Break -35% Without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) )Protection of treated surface with PCG :- The treated surface should be covered with 25mm/50mm F'CC of M-20 grade (1.1.5:3). with proper slope ( 1:120) towards the rain outlets in alternate panels of 2 mt x 2 mt keeping 6 rnm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 co of 100 ml per bag of of cement to be added in the screed concreie(paid separately.for this items).All corners shall be chamfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed prorSeqswith ridti:corict'ete and the peripheral mouth to be sealed with,moisture insensitive epoxy putty of. Sika India .Pvt.Ltd. / MYK Schornbefg /Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with POlysulphide Sealant.(Paid Separately). Be d - Sika India Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc . Warranty for five years.

Covering of treated surface with PCC :-providing 25 mm thick Cement Concrete M20 (1:1:5:3) maintaining slope in alternate 2 mt x 2mt panels With approved quality of stone chips of 20mm to 6 mm size graded and Cleaned sand of F.M.2.5 to 3 including screening, shuttering, and mixing Cement concrete in mixer with admixture of integral water proofing and Placing in position, striking curing, taxes and royalty all complete as per Building specification and direction of E/I. Panels that has been left should Be casted next day. There should be 6 mm gap between panels .brand- Sika _ plastocrate plus, MYK proof WP 10, Fosroc- Conplast X 421 ic Dr Fixit Pidiproof LM+

Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc-Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent

Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysuiphide Sealant (Porin.g Grade)as per drawings and technical specificationsi6nd direction of E in Charge. (with 18% GST) B rand Sika Polysulphide, Fosrpc-Thioflex 600 Dr. Fixit Pidiseal PS(42P. MY K Seal PS or Euivalent.

Granular Sub-base with Close Graded Material (Table:- 400-1) By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) for grading- I Material

Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m

Cost of Driling 200mm x 165mm x 125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as meteranufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914. F.A.S.D starter

Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004

Supplying chemical emulsion in sealed containers including delivery as specified.-Chlorpyriphos emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emul?sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:-With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 6 mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.40 mm thick

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red. : Area of slab over 0.50 sqm

Extra for providing edge moulding to 18mm thick marble stone counters,Vanities etc. over Item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

Float glass panes - 4 mm thick glass pane (weight not less than 10 kg/sqm).

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 1 0 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 0 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.- Twin rubber stopper

Providing & Fixing decorative high pressure laminated sheet of plain I wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5mmthick

Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R2 series with frame (39 mm & above) x (39 mm & above) & sash /mullion (39 mm & above) x (60 mm & above). (Height upto 1 . 2 metre)

Supplying and fixxing rolling Shutters of approved make, made of required size M.s. laths, interlocked together through their entire lenth and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454-part 1 and M.S.top cover of required thickness for rolling shutters. : 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providind and fixing ball bearing for rolling shutters.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Extra for pre finished nosing to treads of steps of marble stone

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 1 8 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 : 4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 75 mm

Coupler 110 mm each

Single pushfit Coupler 75 mm

Single pushfit Coupler 110 mm

Single tee with door 75x75x75 mm

Single tee with door 110x110x110 mm

Single tee without door 75x75x75 mm

Single tee without doo 110x110x110 mm

Bend 87.5° 75 mm bend

Bend 87.5° 110 mm bend

Shoe (Plain) 75 mm Shoe each

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1 . 6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 1 0 . 5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as meteranufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 1 2 . 5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I ) :2011 (Board with BIS certification marks)

Providing and Fixing 1 5 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws@ 230 mm interval and laying 1 5 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1 .6 mm fixed to ceiling with 1 2 . 5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main 'T'. Bottom exposed with 24 mm of all T-sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRG value of 0.50 (Minimum), light reflection> 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supply , laying fixing , testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc. ) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 kg/ cu m density, thermal conductivity 0.037 W/MK or b etter at 20 deg mean temperture class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect.

40 mm dia (32 mm thick insulation)

32 mm dia (19 mm thick insulation)

25 mm dia (19 mm thick insulation)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 178 mm

Providing and fixing Special type of C.P. Bath room fittings for V.l.P. Buildings (JAL, Jaquar, Marc or equivalent make) (lSl Marked) Sink Cock with swinging casted spout (lSl Marked)

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and placing on terrace (at all floo levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and marking necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass Stop Cock (concealed) of standard designand of approved make conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 450 mm dia. R.C.C. pipe

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 meter deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With brass cover plate minimum 1.25 mm thickness

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted floatglass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in Charge.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick

SS handle 125 mm

Zinc alloy (white powder coated) cresent lock for uPVC sliding door/ window

Ply Wood (national or eqivalent make) : 25mm thick

Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I

Aggregate

Stone Metal

Brick

Fly Ash Brick

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of Hindustan "Parry" or any other approved I.S.S. Make with 5 liters capacity C.I. Automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. bracket, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400grams, 15mm P.V.C./Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I. (a) Flat back or standing corner (600mmX350mm)

Supplylng, fitting and fixing the following items complete with all materials as per specification and direction of E/1. : C.P. brass towel rail 20mmX600mm with bracket container

Supplying, materrials and labour for constructing inspection chamber of designation class 75B brick size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Power Plug Wiring in PVC conduit (2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 sqmm + 1x1.5 sqmm earth wire for separate 3 pin 5A sockets

2x2.5 sqmm + 1x2.5 sqmm earth wire for switch board

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4x10 sqmm + 2x6 sqmm earth wire

Point wirring in PVC conduit, with Modular type switch :- Wiring for Light point/fan point/exaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core in Surface/ recessed PVC conduit, with modular type switch , Modular plate, suitable G.I boxes etc. as required .Group-C

Wirilg in cxisting conduit :- ls"ppfyr"g and drawing following sizes of FR PVC insulated copper lconductor single core cable in existing zurface / recessed steel / PVC loonarit including dismantling as required : 4x2.5 sq.mm

SIF PVC conduit :- Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

S/F Modular Type switch/ socket:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6 A switch one way switch

5/6 amps, 3 pin Socket outlet socket outlet

S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

S/F Modular boxes, base & cover plate - Supplying and fixing following size/modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 module (78mm x 78mm x 45mm)

4/5 module (78mm x l40mm x 50mm)

8/9 module (78mm x 230mm x 60mm)

12 module (135mm x 205mm x 60mm)

S/F light plug point with modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc. as required . (For light plugs to be used in non residential buildings)

S/F power plug point with Modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface of in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc. as required. (For light plugs to be used in non residential buildings)

S/F ceiling rose :- supplying and fxing 2 pin 5 amp. Ceiling rose on the existing junction box/ wooen block including connection etc. as required .

ITC fluorescent fitting with down rods:- Installation testing and commissioning of pre-wired, fluorescent fitting ./ compact fluorescent fitting of all types, complete with all accessories and tube etc. including supplyrng and fixing ball and socket arrangement 2 no. down rods of 20mm dia x 1.6 mm thick steel conduit/Gl pipe upto 30 cm length. , painting and wiring the down and connection with 1.5 sq.mm PVC insulated, copper conductor, single core cable and earthing etc. as required

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F T. P. MCB DB :-Supplying and fixing the follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator).

4 way(4+12) Double door Horizontal type

4 way(4+12) Double door Horizontal type

4 way(4+12) Double door Horizontal type

S/F 'C' series SP MCB: Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10 kA, "C" curve, miniature circuit breaker suitable for.inductive load of following poles in the existing MCB DB complete with connections, esting and commissioning etc. as required.

6/32 amps, Single pole

40 amps, DP

40A TPN MCB

50/63 amps, TPN

S/L 8 SWG copper wire in ground :- Supplying and laying 8 SWG copper wire at 0.50 metere below ground level for conductor earth electrode, including soldering etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

P/p G.I. lightning condutor finial :- Providing and fixing of lighting conductor finial , made of 25mm dia 300mm long , G.I. tube, having single prong at top, with 85mm dia 6mm thick G.I. base plate including holes etc. complete as required.

Pff G.I. lightning conductor tape in horizontal mn :- Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for Horizontal run ).

PIF G.I. lightning conductor tape in vertical run :- Providing and fxing G.I. tape 20mm x 3rrm thick on parapet or surface of wall for lightning conductor complete as required.( for Vertical run ).

Suypplying and Fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.100 mm X 100 mm X 60 mm deep

Supply and fixing following size / modules , GI box along with modular base & cover Plate for modular switches in recess etc. as required. 1 or 2 Module (75mm X 75mm )

Supplying and drawing of UTP 4 Pair CAT 6 LAN Cable in the existing surface / recessed steel / PVC conduit as required. 1 run of cable

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 2 nos, 3 pin 5/6A modular socket outlet and 2 nos 5/6 A modular switch, connections etc as required.

Supplying and Fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25A modular socket outlet and 25A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. : 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required . : 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required . : 300 mm width X 50 mm depth X 1.6 mm thickness. : 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. : 300 mm width X 50 mm depth X 1.6 mm thickness

Supplyind and making end termination with brass compression gland and Aluminium lugs for flowing size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required

3.5Cx25 sq.mm (28mm)

3.5 X 70 Sq mm (38 mm)

3.5 X 185 Sq mm (57mm)

3.5 X 240 Sq mm (62mm)

S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 1C[.Z70Y AC,50Hz. Luminarie shall be confirm tolS:,1,0322part-5/section-5 and shall be complete with all neccssary accessories as required 150/160W LED Flood light

S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722 with all neccssary accessories as required

l2W LED Round Down ligbt

l5ll6w LED Round Down light

18/20W LED Round Down light

I'x I' LED Panel light

2'x2' LED Panel ligbt

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of standard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wire uitable for 230V 50H2, single phase supply etc. complete as required

1200mm (48") BLDC 5star rating 32W Ceiling Fan

l400mm (56") BLDC 5star rating 32W Ceiling Fan

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required.-20/22W LED Tube light

Layrng of one number PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size exceeding 185 sq mm but not exceeding 400 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable of l. l KV grade of size exceeding 95 sq mm but not exceeding 185 sq. mm in the existing RCC/HUME/STONEWARE/IvIETAL pipe as required.

Layrng and fxing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. lUpto 35 sq. mm (clamped with lmm thick saddle)

Outdoor Unit: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .Make - Hitachi / Daikin/ Mitsubishi Heavy

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fansection with low noise fan/dynamically balanced blower, multi speed motor, coil section with DX Coppercoil, electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, asrequired. The unit shall have automatic force shutdown provision in case off ireon receiving signal from BMS System. The cooling capacity of indoor unit will be at air in let conditions of 27Degree CD Band 19 Degree CWB temperature.

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic mediapre-filter, fan section with low noise fan/dynamically balanced blower, multi speed motor, coilsection with DX coppercoil, electronice xpansionvalve, outercabinet, cord less remote control, drainpan, necessary accessories etc., suitable for operationon 230V±10%, 50Hz, single phase AC supply, complete as required.The unit shall have automatic force shutdown provision incase of fire on receiving signal from BMS system. The cooling capacity of indoor unit will be at air in let conditions of 27Degree C DB and 19 Degree C WB temperature.

Supply,Installation,testingandcommissioningincludingvaccumiazationandNitrogentestingoffollowingnominalsizesofsoft/harddrawncopperrefrigerantpipingforVRV/VRFsystem,completewithfittings,withsuitableadjustableringtypehangersupports,jointing/brazingincludingaccessories,insulatedwithXPLEClass-Otubularinsulation/withClass-OclosedcellelastometricnitrilerubbertubularsleevessectionsofspecifiedthicknessasgivenbelowforSuctionandLiquidlines,allaccessoriesasperspecifications etc. as required :

6.4 mm dia(OD) (Softdrawn) with tube thickness 1.2mm with19mm thick insulation

9.5 mm dia(OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

12.7mmdia(OD)(Softdrawn)withtubethickness1.2mmwith19mm thick insulation

15.86 mm dia(OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

19 mm dia(OD) (Harddrawn) with tube thickness 1.2mm with 19mm thick insulation

22.2 mm dia(OD)(Harddrawn) with tube thickness 1.2mm with 19mm thick insulation

28.58 mm dia(OD) (Harddrawn) with tube thickness 1.2mm with 19mm thick insulation

34.9 mm dia(OD )(Hard drawn) with tube thickness 1.62mm with 19mm thick insulation

41.27 mm dia(OD) (Harddrawn) with tube thickness 1.62mm with 19mm thick insulation

Supplying of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including 1100 volts. (Conforms to IS:1554,part-1):25 sq. mm,3.5 core

Supplying of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including 1100 volts. (Conforms to IS:1554,part-1):70 sq. mm,3.5 core

Supplying of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including 1100 volts. (Conforms to IS:1554,part-1):70 sq. mm,3.5 core

Supplying of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including 1100 volts. (Conforms to IS:1554,part-1):240 sq. mm,3.5 core

Supply of Exhaust metal Fan 230mm(9"): Supply and fitting of 230mm(9"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required

Supply of Wallmounted Fan: Supply of 16"(400mm), 230V AC wall/cabin fan including fixing the bracket, making , connection testing, commissioning etc as required.

Bulk head 10 LED Fitting: Supply and fixing of 10W LED, surface mounted bulk head PVE water proof housing for indoor/ outdoor

62.5 kVA DG set :Supply, fitting, fixing, errection and commissioning along with civil foundation work of 62.5 kVA D.G. Set, 415 Volts, 3 Ph. Silent Diesel Engine driven generating set as per IS:1460 & IS : 13018 and alternator as per IS:13364 complete with sound proof company make canopy (Acoustic Enclosure suitable for 62.5 kVA D.G. Set.) with breaker panel (automatic Control Panel) and civil foundation work as per the norms of 62.5 kVA Silent D.G. Set with suitable arrangement for Al./Ar./C etc as required. (Make:- Sterling and Wilson Powergen Private Limited with MTU Engine

40 KVA online UPS three phase input and three phase output power system of input, Voltage range 360V/380V / 40OV / 485V AC, Frequenry range 40Hz - 60Hz+ 10%, outputVoltage range 415V I 1%, Frequenry range 50Hz t 1%, Power Factor 0.8/3:1, Harmonic distrortion - < 2% THD (Linear load) : 5% THD (non-liniear load)

MS battery rack suitable for 30 to 35 UI€ Battery installation

12V, 65Ah sealed maintenance free (SMF) battery with 24 month replacement zuaranty. 15:1652:1991

3 core PVC insulated PVC sheathed copper conductor flat submersible cable. Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098 3 Core 4 Sq mm. Copper wire

Supplying Fitting Fixing all height Wall paneling with 12 mm Ply wood (Green/Optima/Red) over 50 mm x 25 mm aluminum Section, Laminate fininsh with all taxes and royalty all complete as per E/I.

Lift Panel : The panel includes 415V, 100A, 3Ph, 35kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Make of MCB - (10kA-C-Series.) L&T/ Legrand/ Schneider / Siemens/ABB/ C&S Make : ISG Ranchi/ SPC Electrotech/ Application Control Panel Pvt Ltd/ Electric Point Incomer 1 No. 63A/FP/ MCB Bus bar -100A, 16kA AL Outgoing 40A ,4P, 30mA RCCB- 1 no 40Amps, TPN, MCB -1 no 16 Amps, DP MCB -1 no 16 Amps, DP RCCB -1 no

UPS panel :- Supplying, designing, manufacturing, installation, testing and commissioning of LT Panel of 14 SWG CRCA sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel , with proper lifting arrangement effecting proper connection of all incomers and outgoing(IP-43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50 kA with front operated construction including separate fabrication arrangement for fixing MCCBs and Bus Coupler. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. The panel includes 415V, 200A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 4, 6, 10 Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Icu=100% Ics with adjustable S/C and O/L Provision for inbuilt earth leakage module & provision for inbuilt measuring unit. Make of MCCB - L&T / Legrand / Schneider / Siemens / ABB/C&S Make of MCB - (10kA-C-Series.) L&T/ Legrand/ Schneider / Siemens/ABB/ C&S Panel Make : ISG Ranchi/ SPC Electrotech/ Application Control Panel Pvt Ltd/ Electric Point The panel consisting of the followings 2 Nos, 100A/FP/25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. (one as incomer from main panel + one as outging to UPS ) Current transformer 100/5A, 15VA, class 0.5 -3 each -1 set LED indicators for each phase and ON/OFF/TRIP -2 set Bus-bar : 415V, 200 A, 25 kA, 3ph, 4wire AL BUSBAR-1 , extensible Outgoings: MCB TPN 40A- 5 nos

AC Panel: The panel includes 415V, 200A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Make of MCCB - L&T/ Legrand / Schneider / Siemens/ ABB/C&S Make of MCB - (10kA-C-Series.) L&T/ Legrand/ Schneider / Siemens/ABB/ C&S Panel Make : ISG Ranchi/ SPC Electrotech/ Application Control Panel Pvt Ltd/ Electric Point Incomer 1 No, 200A/FP/35kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. 6 Nos 63A, 10kA, MCB 2 Nos 40A, 10kA, MCB Electro-mechanical lock for auto changeover -1 set: 200A, 4P Current transformer 200/5A, 15VA, class 0.5 -3 each -1 set LED indicators for each phase and ON/OFF/TRIP -2 set Busbar- 415V, 200 A, 25 kA, 3ph, 4 wire AL BUSBAR-1 , extensible

Main LT Panel :- Supplying, designing, manufacturing, installation, testing and commissioning of LT Panel of 14 SWG CRCA sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel , with proper lifting arrangement effecting proper connection of all incomers and outgoing(IP-43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50 kA with front operated construction including separate fabrication arrangement for fixing MCCBs and Bus Coupler. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. The panel includes 415V, 400A, 3Ph, 50kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, 6, 10 Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Icu=100% Ics with adjustable S/C and O/L Provision for inbuilt earth leakage module & provision for inbuilt measuring unit. The panel consisting of the followings 1 No, 315A/FP/36kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( for incomer for JSEB suppy) 1 No 125A/FP/25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( incomer for DG suppy) Electro-mechnical lock for auto changeover -1 set: 125A, 4P Current transformer 400/5A, 15VA, class 0.5 -3 each -1 set 3 phase kWh meter-1 no LED indicators for each phase and ON/OFF/TRIP -2 set Busbar- 415V, 400 A, 36 kA, 3ph, 4wire AL BUSBAR-1 , extensible Outgoings: 1 No- 100A/FP/25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( for UPS panel) 1 No- 200A/FP/25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( for AC Panel) MCB TPN 63A, 10 kA- 4 nos MCB TPN 40A, 10kA- 8 nos

Roof Top SPV Power Plant : Design, manufacture, supply, testing & commissioning of grid connected 20 kWp Solar Rooftop Power Plant with Battery backup including 05(five) years comprehensive maintenance contract on turnkey basis. (JERADA 2023(category "B-1")

Supplying and stacking at site dump manure from approved source, including carriage up to 5 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 90cm dia, &90cm deep

Anti termite treatment by digging pits 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termiteinfection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.

Providing and Displaying Foxtail palm well developed with fresh & healthy foliage of ht. 210 to 240 cm in big 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Schleichera trijuga (Kusum) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

TOTAL AMOUNT FOR SCHEDULE ITEMS (A)

Non -Scheduled item

Supply of ISI marked 1Cx50 sq mm solid copper conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1.1kV grade.

Chemical Earthing : Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed). Supply of Stainless Steel "U" Bolt Clamp Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)

Supply and installation Outdoor unit piping connection kit ( model-SDG TB 2825) all complete finishings as per direction of E/I.

Supply and installation Outdoor unit piping connection kit ( model-SDG TB 1915) all complete finishings as per direction of E/I.

Supply and installation Refrigerant gas for entire system. (R-410) ECO friendly 1,99,200 all complete finishings as per direction of E/I.

Supply and installation Pressure testing with nitrogen & vaccumasation. all complete finishings as per direction of E/I.

Supply and installation Civil carpentry, masonary,/ core cutting/ scaffolding/ outdoor platform/ false ceiling work etc all complete finishings as per direction of E/I.

Supplying & Placing Executive Table, Particle Board Top W1600 X D1600 X H750 Structure /Frame of table Gable end and modesty panel The type of Storage provided One side E.R.U unit Keyboard tray Not provided Footrest Not Provided Tabletop Material Commercial Block Board MR Grade Conforming to IS 1659 Thickness of table top material (± 1 mm) 36 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end NA Modesty panel material Perforated MS sheet The thickness of the modesty panel material 0.9 mm (for metal sheet) Leg Material Mild Steel (MS) ERW The thickness of the Leg material 1.2 mm Width of tabletop ±10 mm 1500 mm Depth of table ±10 mm 915 mm Height of table ±10 mm 750 mm Size (L x W) /diameter of leg material ± 5 mm NA ERU unit consists of 3 drawers Total Number of drawers /storage in Pedestal units Four drawers Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade Oxford cherry Table /ERU /Pedestal Panel Plain Side Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue

Supplying & Placing Medium Back Chair, Chrome Plated Pipe PU Arm, Gas Lift, Chrome Base, Mesh Back & Seat Net Tapestry Chair mechanism Tilt working with torsion bar mechanism Type of locking Upright locking Number of arm movement N.A Pedestal Base Chrome plated MS Armrest Material Polypropylene Seat material Pressed and moulded with PU foam Backrest is made of One piece hot pressed plywood with PU foam Density of PU foam used in seat KG per Cu Meter (± 3) 40 Density of PU foam used in backrest in KG per Cu Meter (±3) 40 Backrest upholstered with 100% Polyester Fabric Seat upholstered with 100% polyester fabric GSM/Thickness of fabric ±5%(Gram/Square meter) 220 gram Overall width (±10 mm) 650 mm Backrest Height ±15 mm 690 mm Backrest Width ±10 mm 440 mm Seat Height ±10 mm 440 mm Seat Width ±10 mm 480 mm Seat Depth ±10 mm 480 mm Thickness of MS Plate Joining the under structure with Seat 5 mm Thickness of Plywood used in Seat ±1(mm) 12 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 30 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 35 mm

Supplying & Placing Visitor Chair, Cushion Arm, PU Moulded Seat Back, Chrome Plated Pipe stand Leatherette Tapestry Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Legs Armrest type Continuous armrest Seat type Padded Backrest type Padded Frame Material Configuration Two Piece Frame material Stainless Steel (SS 202) Seat material Moulded Plywood Seat material thickness 30 mm Density of Polyurethane foam used in seat (±2 Kg/Cub Meter) 40 Seat upholstered with PU sheet GSM of seat cover (± 3 GSM) 390 GSM Backrest material Moulded Plywood Density of Polyurethane foam used in Backrest ( ±2 Kg/Cub Meter) 32 Backrest upholstered with PU sheet Seat Depth (± 5 mm) 430 mm Seat Width (± 5 mm) 460 mm Seat height from floor surface (± 5 mm) 475 mm Backrest width (± 5 mm) 450 mm Backrest height from seat (± 5 mm) 460 mm Paint Type Chrome Paint Polish Type N.A Colour of Paint N.A Availability of Test Report from Central Govt/NABL/ILAC accredited lab to prove the conformity of product to the Specification Yes Test reports to be furnished to buyer on demand Yes

Supplying & Placing Medium Back Chair, PP Arm, Gas Lift, Nylon Base, PU Moulded Seat & Back, PP Seat & Back Cover, Fabric Tapestry Chair mechanism Centre pivot mechanism Type of locking Tilt limiter Number of arm movement N.A,Pedestal Base Chrome plated MS Armrest Material Polypropylene Seat material Pressed and moulded with PU foam Backrest is made of One piece hot pressed plywood with PU foam Density of PU foam used in seat KG per Cu Meter (± 3) 45 Density of PU foam used in backrest in KG per Cu Meter (±3) 40 Backrest upholstered with 100% Polyester Fabric Seat upholstered with 100% polyester fabric GSM/Thickness of fabric 5%(Gram/Square meter) 290 gram Overall width (±10 mm) 590 mm Backrest Height ±15 mm 600 mm Backrest Width ±10 mm 480 mm Seat Height ±10 mm 460 mm Seat Width ±10 mm 460 mm Seat Depth ±10 mm 410 mm,Thickness of MS Plate Joining the under structure with Seat 0.3 mm Thickness of Plywood used in Seat ±1(mm) 12 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 30 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 30 mm

Supplying and placing of Conference Table,Size : 7300L x 1950W x 750Ht ,36mm thk. Prelam Particle board tabletop with PVC edge banding.Tabletop Supported with 25mm thk Prelam Particle board Side and 18 mm thk Modesty panel with PVC edge banding.6 Module Flip up box above table top for wiring.The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKEDURIAN.WARRANTY-5YEARS

Supplying and placing of EXECUTIVE TABLE FOR CHAMBER OVERALL SIZE: 2100X2100X750MMSupplying, and placing in position of a straight line table with wire manager as per photograph. The main desk top shall be made out of 36mm thick pre laminated particle board with the approved shade. Table top supported with side panels and modesty panel. The side panels made out of 36mm thick pre laminated Particle board & Modesty Panel made out of 18mm thick pre laminated particle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of cable manager hole in the table .The Fixed Side Runner attached to the table of over all 2100Lx450Wx650Ht (H) has a provision for three drawer with lockiing facility , one open shelf , openable shutters with lock.

Supplying and Placing Executive table of specification Structure /Frame of table Gable end and modesty panel The type of Storage provided One side pedestal unit and E.R.U Keyboard tray Not provided Footrest Not Provided Tabletop Material Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates Thickness of table top material (± 1 mm) 36 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end 36 mm Modesty panel material Three Layer Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the modesty panel material 36 mm direction of E/I.

Supplying & Placing High Back Chair, SS Wooden Arm, Synchro Knee Tilt, Gas Lift, Die Cast Aluminium Base Pure Leather Chair mechanism Knee tilt Synchronic mechanism Type of locking 5-Position Locking Number of arm movement N.A Pedestal Base Aluminium die cast Armrest Material MS chrome plated Seat material Pressed and moulded with PU foam Backrest is made of One piece injection moulded frame Density of PU foam used in seat KG per Cu Meter (± 3) 35 Density of PU foam used in backrest in KG per Cu Meter (±3) 35 Backrest upholstered with Pure Leather Seat upholstered with Pure leather GSM/Thickness of fabric ±5%(Gram/Square meter) N.A Overall width (±10 mm) 550 mm Backrest Height ±15 mm 500 mm Backrest Width ±10 mm 440 mm Seat Height ±10 mm 480 mm Seat Width ±10 mm 460 mm Seat Depth ±10 mm 430 mm Thickness of MS Plate Joining the under structure with Seat 0.3 mm Thickness of Plywood used in Seat ±1(mm) 18 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 620 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 35 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 40 mm

upplying & Placing 3 Seater Sofa With Wooden Frame, Powder Coated Leg, Twin Colour Leatherette Tapestry Size in mm - 1930 (L) X 790 (D) X 850 (H) Total Number of Seats in the Sofa Set 3 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos) No Two Seater Unit Number of Three Seater Units (Nos) 1 Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and Backrest Genuine Leather Frame Structure Material and size (±1 mm) 19 mm thick Commercial board Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 40 Type of Spring in the Base / Seating Eight way hand tied spring Length of Single Seater Units in mm (±5 mm) 508 Length of Two Seater Units in mm (±10 mm) 1100 Length of Three Seater Units in mm (±10 mm) 1850 Length of Four Seater Units in mm (±10 mm) 2640 Depth of Sofa Units in mm (±10 mm) 775,Sofa Height (Without Back Cushion) ±5 (mm) 430 millimeter Sofa Height (With Back Cushion) ±5 mm 845 millimeter Seat Cushion Length ±5 (mm) 525 Seat Cushion Width ±5 (mm) 710 Seat Cushion Thickness ±3 (mm) 210 Backrest Cushion Length ±5 (mm) 530 Backrest Cushion Width ±5 (mm) 530

Supplying and Placing 1 Seater Sofa With Wooden Frame, 18 mm thick plywood,seat cushioningf material Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and Backrest Fabric Frame Structure Material and size (±1 mm) Any other wood of minimum 25 mm thickness Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 30 Type of Spring in the Base / Seating Zig Zag spring

Supplying & Placing Centre Table, 12mm Toughened Glass, MS Powder Coated 1200 X 600 X 450 Understructure Number of storage under top No storage Top material Tempered glass Frame material Other wood Dimension of Top (Length X Breadth, or Diameter) ±20mm 1194mmX584mm Height of centre table ±10 mm 460 millimeter Thickness of top material (+/-2 mm) 12 millimeter Thickness of frame material (+/- 1 mm) 12 millimeter

Supplying & Placing workstation table in completely knock down conditions with an overall size 4000mm X 1260mm X 1200mm that is to be assembled at site. The worktop shall be made up of back to back 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in sharing base rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported on particle board base gable end. The end wall of the top shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 4 nos. of drawer having same size. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & Placing Back Storage Unit, 18mm PLPB, Extruded Aluminium Profile W2250 X D450 X H2200 Material of Construction ISI Marked, three layer Prelaminated particle Board conforming to Grade II Type III of IS 12823/2013 laminated with 0.6-0.8 mm thick lamination conforming to IS 2046/1995 and balancing lamination of 0.5 mm thick on the back side Number of Shelves (Nos) 4 Number of Doors (Nos) 4 Height in mm (±10 mm) 2100 Depth in mm (±5 mm) 450 Width in mm (±10 mm) 1830 Thickness of Top in mm (±2 mm) 18 Thickness of Sides in mm (±1 mm) 18 Thickness of Back in mm (±1 mm) 10 Thickness of Bottom in mm (±1 mm) 18 Thickness of shelf in mm (±1 mm) 18 Thickness of Door in mm (± 1 mm) 18 Type of Doors Hinged doors of equal width hung with auto closing hinges of 0 cranking overlay type ,Sliding Type Doors

Providing, supplying and placing in position News Paper / Magazine Stand of Overall Dimensions shall be 900mm(W)x450mm(D)x1850mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.8 mm thick. The front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . Each unit shall be 5 Retractable Display Metal Tray fixed at an angle for easy viewing. Display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns .

Supplying & Placing Steel Almirah, 2 Doors, 4 Adjustable Shelf, Thickness 0.8mm W900 X D 450 X H1830Geeken Technical specification of Almirah steel Generally conforming to BIS specification IS: 3312:2021 (with latest amendment) Type of Almirah steel Almirah Steel shelving cabinets Number of door 2 Number of drawers required No Drawer Number of shelves 4 Colour of finish As per Buyer’s Requirement (to be indicated during bid creation) Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latest amendment) Sheet rounds and flats Conforming to grade E250 of IS 2062 Almirah height(excluding the height of pedestal) ± 5 mm 1980 mm Almirah width ± 5 mm 900 mm Almirah depth ± 5 mm 450 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 1 mm Shelves sheet thickness 0.9 mm Shelves supporting bracket thickness 1.6 mm Hinges sheet thickness 1.25 mm(double folded) Hanging rod wall thickness N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Width of stiffener N.A Stiffener sheet thickness N.A Number of glass sheet fixed N.A Handle size 12 cm Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel finish Finish coat with enamels Conforming to IS:151 Powder coating Conforming to IS: 13871

Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The Almirah shall be supplied with 2 nos. of glass door and 2 nos. of steel door with adjustable shelves. The door shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The glass shall be used 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.

Supplying & Placing Three Seater Desk, PLPB Edge Banded Top, Seat & Back, Powder Coated Pipe Frame, Top Size - 1500 X 400 X 18mm Thick Overall Size - 1500 X 980 X 750 Material of Desk Top +/- 2 mm (For shelf / storage +/- 4 mm) 18 mm thick prelaminated Particle Board Material of Support Structure or Side Pannel Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Height of Desk Top in mm (±5 mm) 750 Width of Desk Top in mm (± 5 mm) 400 TYPE OF DESKING INTEGRATED DESK CUM SEATING Desking Configuration THREE SEATER Length of Desking, Seating and Backrest (if provided) in mm (±10 mm) 1050 Material of Seat and Backrest (if provided) (+/- 2 mm (For back rest +/- 4 mm) 18 mm thick prelaminated Particle Board Material of Support Structure Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Material of Seat Cushion WITHOUT CUSHION Width of Seating in mm (±10 mm) 450 Height of Seat in mm (±10 mm) 460 Width of backrest if provided in mm (± 5 mm) 200 Back Support for Seating of Same materail as Seating back support not provided

Supplying & placing of geeken 4 seater meeting table of specification Seating capacity (number ofseating):4 seaters The shape of table top ::Rectangular,Wire management ::Type of understructure ::Leg type,Material of table top: :Prelaminated MDF

Supplying & Placing Dining/study Table, Powder Coated Pipe Frame, PLPB Edge Banded Top, 25 mm Thick, Size in mm - 1800 X 900 Shape of Table Rectangular Seating Capacity 6 Material of top Prelaminated board Material of understructure Powder Coated MS Material of top finish Mica Length of table ±10mm (Diameter in case of Round) 1800 mm Depth of table ±10mm 900 mm Thickness of top in mm (+/- 5%) 25 mm

Supplying & Placing Café Chair, Chrome Plated Pipe Frame, Leatherette Tapestry Chair Armrest Without Type of seat Ply Seat Cushion With Back Rest Cushion with Upholstery Leatherite Material of frame SS 304 Chair height (overall) ±10mm 880mm Backrest width ±10mm 425 Width of seat ±10mm 400 Depth of seat in mm (+/- 10 mm) 400 Height of seat in mm (+/- 5 mm) 400 Seat Finish Cushioned Exposed Wooden / Metal Parts Finish N.A

Supplying & Placing Steel Library Rack (Double Face), Thickness 0.8mm W940 X D600 X H2110 Type CLOSED FROM SIDES ONLY Number of Shelves/Compartments (Top / Ceiling Shelf - not to be counted) 4 Shelves Material 0.8 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513 Depth in mm (±5 mm) 600 Width in mm (±5 mm) 915 Height in mm (±5 mm) 2000 Paint Powder coated

Supplying & Placing Drinking water palteform Approximate External Dimensions (WXDXH) 750 x 690 x 1420 mm Input Voltage 230 V AC (50 Hz) Power Rating (Max) 850 ± 10% Water Storage Tank Capacity 120 Litre Cooling Capacity 60 LPH Output Water Temperature 15°C±1°C Refrigerant HFC R 134 a Thermal Insulation for Storage Tank PUF No. of Faucets 3 Cold No. of Stages for Filter cum Purifier 7 Active Copper Zinc Booster Yes % of Purified Water Recovery 25% % Rejection of TDS 90% (Approx) Permeate (Purified Water) Production Capacity 50 LPH Storage Tank & Drain Tray Material SS 304 Outer Body Material rest CRCA Powder Coated Steel Front Panel SS 304 and Type of Product Construction Concealed Type of Installation Indoor Net Weight 92 Kg Operating Input Water Pressure 1.0 to 2.0 Kg/cm² Operating Temperature 10°C to 40°C Recommended Total Dissolved Solids in Input Water(TDS) 500 to 2000 ppm.(Max) Recommended Hardness in Input Water 300 ppm(Max) Recommended pH of Input Water 6.5 to 8.5 Allowable Chlorine Input Water 0.2 ppm (Max) Allowable Iron in Input Water 0.3 ppm (Max) Turbidity <5 NTU

Providing & fixing wood wool Acoustic panel 1200 x 600 mm 25 mm thick on GI metal frame of 50 x 25mm making a grid of 610 x 610mm c/c by providing a 50 mm air-gap from wall, the frame work filled with 50mm thick polyfibre 1000 GSM density . Frame is to be backed by chicken mess on top Fire Retardant fabric inserted inside the grippers. Grippers [Centre, Half Wrap & Full Wrap] all complete as per engineer in charge.

Supplying & Placing CARPET Providing & fixing 2 ply cut pile polyster carpet 9mm thick backed with 4mm kinni foam and fevical 505 all complete as per engineer in charge.

Providing & fixing of Handmade acrylic canvas painting as approved by EIC and architect all complete with fiber accessories as per direction by architect.all complete as per engineer in charge.

Firewall SITC of Next Gen Firewal cum Unified Threat Management system alongwith following specs ; Preferred Make-Fortinet/Sophos/SonicWall Security Features Integrated Security Appliance which have these features from day 1 - Firewall, VPN, IPS, Web filtering, Botnet Filtering, Gateway AV, Anti Spyware, Application Control and Geo-IP protection. The firewall should also support anti-Spam services integrated as a license in the firewall. The device should be IPv6 ready (Both phase 1 and Phase2), and should support multi-core architecture and not proprietary ASIC based architecture. Appliance should support IPsec NAT traversal, OSPF, RIP V1 and V2 routing protocol and NAT without degrading the performance of the firewall. Should support authentication using XAUTH/RADIUS, Active Directory, SSO, LDAP, Novell, Internal user database, terminal Services, Citrix. Should have Layer 2 bridge or transparent mode, Wire mode, Sniffer mode /Tap mode Dual WAN/ISP Support : Should support automatic ISP failover as well as ISP load balancing for outbound traffic Network security appliance should support "Stateful" policy inspection technology. It should also have application intelligence for commonly used TCP/IP protocols like telnet, ftp etc. Should support Dead Peer Detection, DHCP Over VPN, IPsec NAT Traversal, Redundant VPN Gateway, Route-based VPN. Should provide complete protection by performing full decryption and inspection of TLS/SSL and SSH encrypted connections regardless of port or protocol. Should proactively detect and block mass market, zero-day threats and unknown malware by inspecting directly in memory solution should support policy-basedrouting, Application based routing and also Multi Path routing & Route-based VPN. Should have capability to look deep inside every packet (the header and data) searching for protocol non-compliance, threats, zero days, intrusions, and even defined criteria. The firewall should support stream/flow-based inspection only without compromising/missing any security features like AV, Windows File Sharing (CIFS), email filter, web filter, VOIP etc. Should detect and prevent hidden attacks that leverage cryptography, blocks encrypted malware downloads, ceases the spread of infections, and thwarts command and control (C&C) communications and data exfiltration Should allow total control to customize which traffic is subjected to decryption and inspection based on specific organizational compliance and/or legal requirements. Vendor & OEM should support the appliance with all necessary upgrade for at least 3 years from the date of purchase installation along with 3 years security software subscription. Should scan for threats in both inbound and outbound traffic simultaneously to ensure that the network is not used to distribute malware and does not become a launch platform for attacks in case an infected machine is brought inside. Should provide real-time monitoring and visualization provides a graphical representation of applications, users and bandwidth usage for granular insight into traffic across the network. Should support Route-based VPN that allow dynamic routing over VPN links to ensure continuous uptime in the event of a temporary VPN tunnel failure, by seamlessly re-routing traffic between endpoints through alternate routes. The firewall must support cloud & appliance-based Sandbox technology and OEM must have own Advanced Threat Protection & Sandboxing solutions. Should have H.323 gatekeeper and SIP proxy support to block spam calls by requiring that all incoming calls are authorized and authenticated by H.323 gatekeeper or SIP proxy. Should support mobile device authentication such as (biometric authentication) fingerprint recognition that cannot be easily duplicated or shared to securely authenticate the user identity for network access. The proposed solution should be scalable and offer fault tolerance to safeguard against hardware failures. The failover should be capable of taking over the traffic without any manual intervention and session loss. Should support deep packet SSL to decrypt HTTPS traffic for scanning(IPS, Gateway Antivirus, Content Filtering, Application control) transparently for future requirement and then re-encrypt and send to destination if no threat found. Should have TLS/SSL decryption and inspection engine that decrypts and inspects TLS/SSL encrypted traffic on the fly, without proxying, for malware, intrusions and data leakage, and applies application, URL and content control policies in order to protect against threats hidden in encrypted traffic. Should have deep packet inspection of SSH to decrypt and inspect data traversing over SSH tunnel to prevent attacks that leverage SSH. Should have IPv6 and should support filtering and wire mode implementations. Should support REST APIs that allows the firewall to receive and leverage any and all proprietary, original equipment manufacturer and third-party intelligence feeds to combat advanced threats such as zero-day, malicious insider, compromised credentials, ransomware and advanced persistent threats. Should have Bi-directional raw TCP inspection. The appliance should be capable of scanning raw TCP streams on any port bi-directionally preventing attacks that they to sneak by outdated security systems that focus on securing a few well-known ports. Should have extensive protocol support to identify common protocols such as HTTP/S, FTP, SMTP, SMBv1/v2 and others, which do not send data in raw TCP, and decode payloads for malware inspection, even if they do not run on standard, well-known ports. Should have SD-WAN feature to choose lower-cost public Internet services while continuing to achieve a high level of application availability and predictable performance. Vendors not having SD-WAN fetures integrated in their firewall should provide additional device to provide this feature support from day 1. Necessary licenses, if required, need to be provisioned from day 1. Should have secure SD-WAN feature that enables distributed enterprise organizations to build, operate and manage secure, high-performance networks across remote sites for the purpose of sharing data, applications and services using readily-available, low-cost public internet services. Vendors not having SD-WAN features integrated in their firewall should provide additional device to provide this feature support from day 1. Should control applications, or individual application features, that are identified by the security engine against a continuously expanding database of over thousands of application signatures, to increase network security and enhance network productivity. Should control custom applications by creating signatures based on specific parameters or patterns unique to an application in its network communications, in order to gain further control over the network. The firewall should support traffic management option to configure traffic shaping on a per policy basis for specific application/ Specific networks and should be able to define guaranteed bandwidth and maximum bandwidth per policy. Should identify and block command and control traffic originating from bots on the local network to IPs and domains that are identified as propagating malware or are known CnC points. Appliance should protect against DOS&DDOS attacks . Should have anti-evasion technology by using extensive stream normalization, decoding and other techniques ensure that threats do not enter the network undetected by utilizing evasion techniques in Layers 2-7 Should not buffer traffic before scanning for IPS and must support inbound and outbound IPS scanning. It should scan the entire traffic and not few specific kilobytes of the session. Should be integrated solution with appliance-based firewall on a single chassis with multicore processor. The device should be featured with Gateway Antivirus and DPI SSL Scanning. The OEM should have regular update of its attack signature database and the same should be configurable to update the signatures automatically without manual intervention. The new attack signatures and new major software releases should be available in OEM website for free download. Should not buffer traffic before scanning for virus. Should have capacity to scan unlimited file size without buffering them. Should be an unlimited user-based appliance. Firewall must support inbound and outbound Antimalware /Antispyware scanning. Should identify and block command and control traffic originating from bots on the local network to IPs and domains that are identified as propagating malware or are known CnC points. Should enforce acceptable use policies and block access to HTTP/HTTPS websites containing information or images that are objectionable or unproductive with Content Filtering Service and Content Filtering Client. Should block content using the predefined categories or any combination of categories. Filtering can be scheduled by time of day, such as during office or business hours, and applied to individual users or groups. URL database should have at least 15 million sites and 50 + categories. There should be a proposed sandboxing solution which should be cloud based or appliance based and employ sandboxing engine for effective scanning. Should have support for analysis of a broad range of file types, either individually or as a group, including executable programs (PE), DLL, PDFs, MS Office documents, archives, JAR, and APK plus multiple operating systems including Windows, Android, Mac OS X and multi-browser environments. The cloud or appliance Sandbox should have technology that detects and blocks malware that does not exhibit any malicious behavior and hides its weaponry via encryption. Should detect and block mass-market, zero-day threats and unknown malware. The Firewall should have the capability to block/prevent from Side Channel attacks like Meltdown, Spectra, Foreshadow, Foreshadow-NG, Port smash etc. The firewall should have single pass, low latency inspection system that performing stream-based, bi-directional traffic analysis at high speed without proxying or buffering to effectively uncover intrusion attempts and malware downloads while identifying application traffic regardless of port and protocol. Should have ability to prevent potentially malicious files from entering the network. Should have support for files sent to the proposed cloud sandbox for analysis to be held at the gateway until a verdict is determined. Should support Zero-Touch registration & provisioning using mobile App. Should have continuously updated database of tens of millions of threat signatures residing in the sandbox servers and referenced to augment the capabilities of the onboard signature database, providing deep packet inspection with extensive coverage of threats. Should support min 20K DPI signatures, 70 million Cloud AV signatures and 3500+ Application Signatures from day 1. Firewall must have cloud-based sandboxing from day 1 and cloud-based sandboxing must have capability to scans 10Mb of files size at a time. Hardware and Interface Requirements The proposed hardware-based firewall should not consume more than 1RU Rack-mountable space The product should have minimum of 12x1GbE, 3x10G SFP+ interfaces from day 1 Appliances should have dedicated 2 USB 3.0 Port, Console Port & Management port Should have 128 GB or more storage (SSD) . Appliance should support dual power supply Should support REST APIs for management Firewall Performance Requirement Threat prevention throughput of 3 Gbps or higher which should include Firewall, Gateway Anti-Virus, AntiSpyWare, Intrusion Prevention and Application Intelligence and Control, URL/Content Filtering and URL & Reputation service from Advance Threat Prevention/Protection/sandboxing services., Anti Spam The Firewall should have at least 3 Gbps of IPS throughput he Firewall should have VPN throughput at least 2 Gbps The Firewall should support at least 1 million maximum connections and 120 K maximum DPI SSL sessions/connections. Should support at least 2,000 IPsec Site-to-Site VPN tunnels , 1000 no of IPsec Client Remote access VPN and at least 500 SSL VPN users Solution should support IPSEC & SSL VPN and Layer 2 Tunneling protocol (L2TP) over IPSEC Licensing and Certification The devices should not have license restriction on number of users. The license should the following subscriptions from day 1 - Firewall, Gateway Anti-Virus, AntiSpyWare, Intrusion Prevention and Application Intelligence and Control, URL/Content Filtering and Advance Threat Prevention/Protection including advance sandboxing. The Firewall should support regulatory compliance like FCC Class A,CE,UL etc. The OEM should have ICSA Labs Advanced Threat Defense certification testing in 2021 and should have overall detection rate of 99% and above. Logging and reporting Should have reporting facility to generate reports on virus dedicated over different protocols, top sources for viruses, destination for viruses, top viruses etc. Firewall shall support onprem or cloud management and reporting solution. Should have options to generate reports in different formats The solution should have configurable options to schedule the report generation. Warranty, Installation, Testing and Commissioning Proposed Solution should support 24x7 telephone, email and web-based technical support.OEM should have TAC and R&D center in INDIA. Manufacturer’s warranty should be mentioned minimum 03 (three) years warranty including all services like GAV, IPS, Antispyware or antimalware, CFS, Application control, BoT protection , Advance Threat Protection, Patch& Firmware upgrade, Cloud based management. Bidder must carry out on site installation, testing and commissioning.

48 Port Access Switch SITC of Layer 2 Fully Manageable Network Switch consists of GigE fixed chassis 48 RJ-45 10/100/1G BaseT, 2 fixed RJ45/SFP combo (1G), 2 fixed SFP+ (1G/10G) uplink/stacking ports. 1RU size, internal AC power supply. Includes country specific power cord, guides, and 19" rack mount hardware. Inclusive of stacking cable.The detailed Specification as follows. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco Port Density 48 X 1G RJ-45 Ports 2 x 1G/10G SFP+ Ports and 2 x 1G SFP/Base-T Combo Ports Internal Power Supply Virtual Chassis/ Stacking Option Upto 4 Switches or more RAM 1 GB or better Flash 1 GB or better Switching Capacity and forwarding Rate 140 Gbps or better and 104 Mpps or better Latency & MTBF Latency: < 4 µs MTBF: 832 k hours Layer 2 Features Mac Address:16K or more VLAN: 4K or more System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes Multicast Group: up to 1000 Quality of Service Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based queues per port, SPQ, WRR Protocol Support Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1 Management Loopback IP address support for management per service, Policy- and port-based mirroring, Remote port mirroring, sFlow v5 and Remote Monitoring (RMON), Unidirectional Link Detection (UDLD),Digital Diagnostic Monitoring (DDM), LLDP-MED, NTP,MVRP, SNMP, sflow or equivalent Security Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks Resiliency Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP) and static LAG groups across modules Operating Temperature and Humditiy Temperature: 0 to 45Deg Humidity: 5% to 95% (non-condensing) Safety Certifications CE, EN 55022, RoHS, WEEE US UL 60950, CSA22.2 FIPS 140-2 EN 60825-1/2 Laser, IEC 62368-1CE, EN 55022, RoHS, WEEE US UL 60950, CSA22.2 FIPS 140-2 EN 60825-1/2 Laser, IEC 62368-1 SFP SFP should be of same make as switch. Stack Cable The Switch should be inclusive of required stack cables Vendor to be present in Gartner Magic Quadrant. The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image.

24 Port Access Switch SITC of Layer 2 Fully Manageable Network Switch consists of GigE fixed chassis 24 RJ-45 10/100/1G BaseT, 2 fixed RJ45/SFP combo (1G), 2 fixed SFP+ (1G/10G) uplink/ stacking ports. 1RU size, internal AC power supply. Includes country specific power cord, guides, and 19" rack mount hardware. Inclusive of stacking cable.The detailed Specification as follows. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco Minimum specification Port Density 24 X 1G RJ-45 Ports 2 x 1G/10G SFP+ Ports and 2 x 1G SFP/Base-T Combo Ports Power Supply Internal Power Supply Virtual Chassis/ Stacking Option Upto 4 Switches or more RAM 1 GB or better Flash 1 GB or better Switching Capacity and forwarding Rate 92 Gbps or better and 68 Mpps or better Latency & MTBF Latency: < 4 µs MTBF: 2595 k hours Layer 2 Features Mac Address:16K or more VLAN: 4K or more System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes Multicast Group: up to 1000 Quality of Service Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based queues per port, SPQ, WRR Protocol Support Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1 Management Loopback IP address support for management per service, Policy- and port-based mirroring, Remote port mirroring, sFlow v5 and Remote Monitoring (RMON), Unidirectional Link Detection (UDLD),Digital Diagnostic Monitoring (DDM), LLDP-MED, NTP,MVRP, SNMP, sflow or equivalent Security Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks Resiliency Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP) and static LAG groups across modules Operating Temperature and Humditiy Temperature: 0 to 45Deg Humidity: 5% to 95% (non-condensing) Safety Certifications CE, EN 55022, RoHS, WEEE US UL 60950, CSA22.2 FIPS 140-2 EN 60825-1/2 Laser, IEC 62368-1 SFP SFP should be of same make as switch. Stack Cable The Switch should be inclusive of required stack cables Vendor to be present in Gartner Magic Quadrant. The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image.

24 Port POE Access Switch SITC of POE+ Layer 2 Fully Manageable Network Switch consists of Fixed 1RU chassis 24 PoE 1G BaseT, 2 fixed RJ45/SFP+ combo (1G/10G), 2 fixed 1G/10G SFP+ uplink/VFL ports. Internal AC PSU (380 budget), includes country specific power cord, guides and 19" rack mount kit. Inclusive of stacking cable.The detailed Specification as follows. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco Minimum specification Port Density 24 X 1G RJ-45 PoE+ Ports with 380W power budget 2 x 1G/10G SFP+ Ports and 2 x 1G SFP/Base-T Combo Ports upgradable to 2 x 10G SFP+ Ports Power Supply Internal Power Supply Virtual Chassis/ Stacking Option Upto 4 Switches or more RAM 1 GB or better Flash 1 GB or better Switching Capacity and forwarding Rate 128 Gbps or better and 68 Mpps or better Latency & MTBF Latency: < 4 µs MTBF: 1447 k hours Layer 2 Features Mac Address:16K or more VLAN: 4K or more System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes Multicast Group: up to 1000 Quality of Service Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based queues per port, SPQ, WRR Protocol Support Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1 Management Loopback IP address support for management per service, Policy- and port-based mirroring, Remote port mirroring, sFlow v5 and Remote Monitoring (RMON), Unidirectional Link Detection (UDLD),Digital Diagnostic Monitoring (DDM), LLDP-MED, NTP,MVRP, SNMP, sflow or equivalent Security Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks Resiliency Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP) and static LAG groups across modules Operating Temperature and Humditiy Temperature: 0 to 45Deg Humidity: 5% to 95% (non-condensing) Safety Certifications CE, EN 55022, RoHS, WEEE US UL 60950, CSA22.2 FIPS 140-2 EN 60825-1/2 Laser, IEC 62368-1 SFP SFP should be of same make as switch. Stack Cable The Switch should be inclusive of required stack cables Vendor to be present in Gartner Magic Quadrant. The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image.

10G SM SFP+ Module SITC 10 Gigabit optical transceiver SFP+). Supports monomode fiber over 1310nm wavelength nominal with an LC connector. Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco

6 Port SM LIU 6 Port LIU Switch : SITC of 6 Port Loaded LIU with SC Unit for 6 SM fiber Single Mode fibres OS2 (1 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 6 Fiber Capacity & 6 Nos. of SC Pigtail - Pigtail 1 Meter SM Os2 (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Fiber Optic LIU Rack Mount LIU (6 Ports) Fiber optic patch panel : Fiber optic patch panel FMS Termination Drawer should have sufficient slots to accommodate 3 of 12/16 Port LC Adaptor Plates. Should have Slide type drawer structure Height: 1 U, 1.75 inches (12 & 24 Ports) Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder Slots: FMS should have sufficient slots to accommodate adaptor plates Empty Slots of FMS should be covered with blank plates. Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU. Detailed Specs for 6/12/16 Port LC/SC Type Adaptor Plates (SM OS2) The adaptor plate should be pre-loaded with LC/SC Type Single ModeDuplex Adaptors. Port Density :6/12/16 LC/SC Single mode Ports All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal. Insertion Loss: <0.2 to <0.1 dB Compliance :RoHS Compliant Detailed Specs for LC Type 9/125μm SM Fiber Optic Simplex Pigtail Type : 9/125 micron fibre performance Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2 Operating Temperature: -40°C to +75°C Connector Insertion Loss: 0.30dB(Max) Attenuation: 1310/1550 : 0.36/0.22 dB/KM

24 Port LIU Switch : SITC of 24 Port Loaded LIU with SC Unit for 24 SM fiber Single Mode fibres SM OS2 (12 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 Meter SM (Make:Legrand/Panduit/RIT/Siemon)

Fiber Patch Cord SITC of Fiber Duplex Patch Cords SC-LC SM Patch Cord 2 mtr. (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Patch Cord, LC SC, Duplex, SM, Bend Insensitive G651, PC, LSZH Cable : LC/SC-SC/LC 9/125μm or 1310 μm SM Duplex Patch Cord Length : 2mtrs (as per requirement) Connectors : The optical fiber patch leads shall comprise of Single Mode 9/125μm or 1310 μm fiber with 2XLC type fiber connectors terminated at one end of fiber patch cord and 2xSC type connector at other end of the fiber patch cord Insertion loss should be better than ≤ 0.30 dB Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2 Attenuation: 50/1300 : 3.0/1.0 dB/KM Connector Loss : 0.30dB(max) Operating Temperature : -40°C to +75°C

6-Core SM Armoured Fibre Optics Cable Supply and laying of 6 core Single mode OS2 Loose tube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Outdoor F/O Cable, Loose Tube, SM – 1x6 Fibers, Central Steel rod with CST, PE The fiber should be optimized for operation at 1310 nm and at 1550 nm. Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type OS2, ITU-T REC G 652D spec IEC 60794-1-2 F5 Fibre Count : 6 /12 Fiber count per tube :6 / 12 Filler count :4

Patch Panel-24 Port Fully Loaded SITC of Fully Loaded 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for 19" 1U 24 port unsheilded Patch Panel Patch panel should be modular design, populates up to 24 UTP keystone-type jacks in 1U Patch panel should be Enhanced with cable strain relief with retention tray; It should be single metal both front panel and rear tray Material: sub-rack made of MS Steel with dimension 44.4 mm : 482.6 mm : 105 mm (h:w:d) tray Information Outlet or connectin module should comply with the specification mentioned above in 2 Standard : Conforms to IEC-60603-7 (603-7) for keystone-type, snap-on apertures Should be RoHS complied

Straight LAN Patch Chord-2 Mtr SITC of Straight LAN Patch Chord-2 Mtr (Make:Legrand/Panduit/RIT/Siemon)

Straight LAN Patch Chord-1 Mtr SITC of Straight LAN Patch Chord-1 Mtr (Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Patch Cord, U/UTP 4P, Cat.6, length 1/2 meter Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5 Cable shield: U/UTP Number of conductors : 8 Stranding: 7 x 0.20 mm (24 AWG) Cable jacket characteristics: cable, metal-free Cable overall diameter: 6.5±0.2 mm Tube / Wire type: stranded conductor Insulation: solid polyolefin, 0.97±0.02 mm diameter Plug: Feature cable retension, with enhanced pull strength. Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending. Jacket: PVC with 8 different color options Plug should have high repeatability cross talk performance

I/O Dual Module Facplate Supplying, delivery, installation, testing and commissioning of Flush mounted Cat 6 Information Single Outlet Box.on GI concealed Modular Switch Board including connections and making good the damages caused complete as required & as per Direction of Engineer-In-Charge.(Make:Legrand/Panduit/RIT/Siemon) Detailed Specs for Faceplate Should be UK style Keystone-type Faceplates are available in 1, 2 & 4 port configurations Should be featured with shutter options, the screws not to be visible Should support Work with both Flush and Wall mount box Should support Operating Temperature: -10～+60; Storage Temperature: -40～+68; Humidity: 15%~90% RH Material: ABS, UL 94V-0; Spring: SUS304; Surface Finish: Polished Detailed Specs for Cat 6 UTP RJ 45 Keystone Jack RJ45 Jack of Category 6, for the establishing of transmission channels of class E with up to 4 plugged connections, complies with Category 6 requirements of the standards ISO/IEC 11801:2nd edition, EN 50173-1, DIN EN 50173-1: 2002 as well as ANSI/TIA/EIA 568-B.2-1, de-embedded tested in acc. with IEC 60603-7 (603-7), interoperable and backwards compatible with Cat.5e and Cat.5. Suitable for 10GBase-T applications in acc. with IEEE 802.3an up to 500 MHz and 55 m. Compatible with RJ standard plugs (RJ11, RJ12, RJ45), PCB- and tool based connection of installation cables AWG 24 – 22 (0.5 mm – 0.65 mm) and flexible cables AWG 26/7 – AWG 22/7. IDC termination should feature nil crossover in acc. with EIA/TIA 568-A/B, gold-plated bronze contacts for >750 mating cycles, >200 insertion cycle Material: RoHS complied Housing material: Polycarbonate (UL-94-V0) Should be available with or without dust protection feature Should be 3P certified

Fiber Splicing Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

Wall Mounted 15 U Rack SITC of Fully Loaded 15U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,16A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; The Front frame should be integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 iPreffered Make-Legrand/Netrack/President/Valrack

Floor Mount Rack Providing, fixing, fitting, installation and testing of 22 U Network Rack as server cabinet 19" LCS2 along with all standard accessories, 800mm (W), 1000mm (D), CRCA 'D' grade 1.6mm thick sheet, pwoder coated for cabinet , 4mm Toughened Tinted Glass Door and along with following accessories:- 1. Cooling fan 220/230V AC, of 90 CFM-- 4 Nos. , 2. Cable manager Metal 4 Nos. 3. PDU- 230V /AC 1 No., 6. Mounting Hardware (20 Sets of M-6 screws, washers, cage, nuts (Nickle Coated)- 3 Nos. ,7. Earthing strips copper 150mm H 1 No. 8. Door Lock 1 No. ,9. Caster Wheels (with breake) 2 Nos. 10. Caster Wheels (without breake) 2 Nos. ,11. Front Metal Band 1 No. (Preferred Make-Valrack/President/Rittal/Netrack

IPABX System SITC of IPABX SYSTEM: IP based 100% non-blocking EPABX System should be a IP Compatible with rich feature set of the system and can be connected with pure Voice over IP (VoIP) communication network across corporate Local and Wide Area Networks (LAN and WAN) as & when required. The system should support server gateway architecture The system should be rack mountable. Must Support Unified Communications. It should have latest TEC Approval (TEC: 60030:2016) vide TEC CERTIFICATE GR NO.TEC/GR/SW/PBX/-005/01/SEP-16 FOR IP- PABX or latest.The offered IPPBX system shall be enabled with Unified Communication and Collaboration Application. IP-PBX should employ IP at Core as Switching Technology employing Packet Switching conforming to latest ITU-T (earlier CCITT) standards.9. The single IP EPABX system should have a provision of future expandability to 2500 ports (any mix/percentage of analog/digital/IP).Infuture If required, the same system should be capable to upgrade as Server- Gateway Architecture support and all Existing Hardware should be used with Expansion support of 32000 Ports. Conference management should be done through web interface Equipped with 25 IP Extensions expandable upto 200 Ports,8 Analog Trunk Ports, 1 PRI , 02 Ports Auto Attendant,1 Nos. Operator Console. IPBX Make: Tadiran/Syntel/Alcatel

Type 1 IP Phone SITC of IP Phone with Following Specs; Preferred Make: Tadiran/Syntel/Alcatel i. The Phone should have 2.4 inch (320x240) color - screen LCD display. ii. The Phone should have minimum two Giga ethernet ports. iii. The phone shall support PoE and external power adaptor. iv. The phone should support HD Voice v. The phone should have Full-duplex hands-free speakerphone vi. The phone should support headset. vii. The phone support minimum 2 SIP accounts. viii. Desktop/Wall mountable ix. The Phone shall have 4 soft keys, 5 navigation keys, 4 function keys. x. The Phone shall support auto provision via FTP / TFTP / HTTP/ HTTPS for easy configuration &amp; fast deployment.

Battery Interconnecting Cable Supply, fitting, fixing, commissioning and testing of 35 Sq. MM Copper Conductor Multi strand PVC Sheilded FRLS Wire with suitable Copper LUGS for Battery Interconnection and suitable 50 Sq. mm copper wire of 4 length of 10 mtrs each for UPS to Battery excluding cable from PANEL to UPS and UPS to panel. Make- Polycab/Havells/KEI

Earthing Chemical Earthing Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed). Supply of Stainless Steel "U" Bolt Clamp Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)

Bullet Camera SITC of Bullet Camera of having 5 MP resolution-OEM Authorisation,OEM should have factory in India with following Specifications; Preferred Make: Honeywell/Uniview/Prama Feature Specification Image Sensor 1/2.7'' Progressive Scan CMOS or Better Min. illumination 0.005 Lux @ F1.6, B/W: 0 Lux with IR Preferred recording Resolution 5MP (2560 X 1920 ) or better Day & Night IR Cut Filter Shutter speed 1/3 s to 1/100,000 s WDR 120dB WDR or better Lens type Fixed lens 4mm or better IR range 60m IR or higher Streaming Type Should Support three video streams. Video Compression H.265,H.265+,MJPEG Audio Compression G.711ulaw/G.711alaw/G.722.1/G.726/MP2L2/PCM/AAC Image Enhancement BLC, 3D DNR,120dB WDR,ROI (1 fixed regions for main stream). Image settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser Day/Night Switch Day, Night, Auto, Schedule Network Protocol TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, NTP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv6, Bonjour, IPv4, UDP, SSL/TLS,ONVIF(G,S,T),ISAPI. Simultaneous Live View 6 channel User Host 32 users. 3 user levels: administrator, operator and user Edge base Recording storage Built-in memory card slot, support microSD card, up to 256 GB Preferable analytics features Motion detection,video tampering alarm,Line crossing detection, intrusion detection. Event Alarm Notify surveillance center, trigger recording, trigger capture, send email. Ethernet Port 1 x RJ45 10M/100M Ethernet port General Function Anti-flicker, heartbeat, mirror, password protection, privacy mask, watermark, IP address filter. Power Supply DC12V, PoE (802.3af, Class 3) Operating Conditions -30° C ~ + 60° C Ingress Protection IP67 Certifications CE,FCC,RoHS,BIS.

Dome Camera SITC of Dome 5 MP resolution-OEM Authorisation,OEM should have factory in India with follwing specifications Preferred Make: Honeywell/Uniview/Prama/Sony Feature Specification Image Sensor 1/2.7'' Progressive Scan CMOS or Better Min. illumination 0.005 Lux @ F1.6, B/W: 0 Lux with IR Preferred recording Resolution 5MP (2560 X 1920 ) or better Day & Night IR Cut Filter Shutter speed 1/3 s to 1/100,000 s WDR 120dB WDR or better Lens type Fixed lens 2.8mm or better IR range 40m IR or higher Streaming Type Should Support three video streams. Video Compression H.265,H.265+,MJPEG Audio Compression G.711ulaw/G.711alaw/G.722.1/G.726/MP2L2/PCM/AAC Image Enhancement BLC, 3D DNR,120dB WDR,ROI (1 fixed regions for main stream). Image settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser Day/Night Switch Day, Night, Auto, Schedule Network Protocol TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, NTP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv6, Bonjour, IPv4, UDP, SSL/TLS,ONVIF(G,S,T),ISAPI. Simultaneous Live View 6 channel User Host 32 users. 3 user levels: administrator, operator and user Edge base Recording storage Built-in memory card slot, support microSD card, up to 256 GB Preferable analytics features Motion detection,video tampering alarm,Line crossing detection, intrusion detection. Event Alarm Notify surveillance center, trigger recording, trigger capture, send email. Ethernet Port 1 x RJ45 10M/100M Ethernet port General Function Anti-flicker, heartbeat, mirror, password protection, privacy mask, watermark, IP address filter. Power Supply DC12V, PoE (802.3af, Class 3) Operating Conditions -30° C ~ + 60° C Protection IP67 & IK10 or Better. Certifications CE,FCC,RoHS,BIS.

NVR SITC of 32 Channel NVR Processor :OEM Authorisation,OEM should have factory in India with follwing specifications Preferred Make: Honeywell/Uniview/Prama/Sony Features Specification Operating System Embedded LINUX with GUI Live view channels 32 Channel Recording/Live view/Playback resolution Support resolution up to 32MP Network thoughput Incoming bandwidth : 380Mbps Outgoing bandwidth : 256Mbps. VGA and HDMI output resolution 1 X HDMI: 4K (3840 × 2160), 2K (2560 × 1440), 1920 × 1080 2 X HDMI :4K (3840 × 2160), 2K (2560 × 1440), 1920 × 1080 1 X VGA & 2 X VGA:1920 × 1080p Audio Input / output Input x 1-ch, output x 2-ch Decoding format H.265/H.265+/MPEG4 Playback capability 16ch-@1080 (30fps) or better Network protocols TCP/IP, DHCP, IPv4,IPv6, DNS, DDNS, NTP, SMTP, NFS, iSCSI, UPnP™, HTTP, HTTPS,ONVIF (S&G). SATA 4 X SATA interfaces with 12TB capacity and 1X eSATA interface. RAID feature Should support RAID5,RAID6,RAID10. Analytics Features Supports multiple analytics by camera and NVR as well eg: Motion detection, line crossing, intusion detection,heatmap, ANPR ,face recognition,face analytics,face comparison, people counting. Network interface 2 X RJ-45 10/100/1000 Mbps self-adaptive Ethernet interface USB interface 2 X USB 2.0 and 2 X USB 3.0 Serial interface 1 X RS485 (full duplex) , 1 X RS232 Remote connection min. 64 connection Alarm interface Input: 8 channel and Ourput : 4 channel. Power supply 100 to 240 VAC. Max. Power Consumption ≤ 30 W Working temperature -10 to +55 ºC Working humidity 10% to 90% Certification ONVIF , CE,FCC and BIS.

HDD SITC of 8 TB Surveillance Grade Hard Disk for NVR for 30 Days Back up; Make-Seagate/WD

55 Inch LED Panel Supply, Installation, Testing and Commissioning of 55" LED Display Panel, with 4K Resolution : 3840 x 2160, 500 nits (cd/m2) Brightness, contrast ratio : 4000:1, Viewing Angle : 178° h/v, response time : 8ms, Display Colors- 16.7 Mill; Built in Speaker-10W+10W ; Inputs : HDMI x 2, DVI‐D, DisplayPort, Audio, RS‐232 Control, 100‐240 VAC @ 50/60Hz Power Supply, 24x7 Operation.; Preferred Make LG/Samsung/Panasonic

Interactive Panel SITC of Interactive Flat Panel: Size-85" , Brightness :350; Panel Type: VA; Resolution :3,840 x 2,160 ; Pixel Pitch (HxV), 0.4875(H) mm x 0.4875(W) mm; Contrast Ratio: 4000:1(without glass); Response Time: 6ms(Typ.); Colour Gamut : 72%; Glass Haze: 2%(without glass); Operation Time Support : 16/7 ; HDMI In: 2; DP In: 1 ; USB: 2(Main/Tray), 2.0/3.0, External(Tray); Audio Out: Stereo Mini Jack; Video Out: Yes; RS232 In : Yes; RJ45 In: Yes; WiFi : Yes; Bluetooth: Yes. Preffred Make-Samsung/LG/Peoplelink

OPS SITC of OPS Device for intractive Panel with 8th Gen Intel Core i5 8th Gen, 8260u 4K@ 60Hz processor, 16GB DDR4 RAM, 128GB SSD, 1TB HDD, WIFI+BT, Win 11, Wireless Keyboard & Mouse; Make-: As compatiible to the Intractive Panel

Camera SITC of PTZ Camera USB based : Yes; Zoom : Minimum 20X Optical Zoom; Digital 16X; Iris: f=5.5~110mm ; F1.6 ~ F3.5;Viewing Angle:3.3° (tele) –54.7° Wide ;Sensor:1 /2.8inch or better CMOS sensor; Mega Pixels:2.07 ; Video Format: SDI Video Formats: 1080P60/50/30/25/59.94/29.97 ; 1080I60/50/59.94. 720P / 50/ 30 / 25 /59.94/29.97; Minimum illiumination:0.5 Lux ; DNR:2D & 3D DNR; White Balance :Auto/Manual/One push 3000K / 3500K / 4000K / 4500K / 5000K / 5500K / 6000K / 6500K /7000K; Electronic Shutter : Auto/Manual; Focus : Should be Auto/Manual/One Push; BLC:ON/Off; WDR : Off/Dynamic level adjustment; Video Adjustment: Brightness, Color, Saturation, Contrast, Sharpness, B/W mode, Gamma curve; SNR : >55 dB; Interface : USB 2.0 x1 , USB 3.0 x1, LAN x1, RS232 x 1, HDMI x 1 ; Audio InVideo Compression Format:H.265/H.264 ; Control Protocol: VISCA/PELCO-D/Pelco-P; Baud Rate : 11520 / 9600 / 4800 / 2400 ; LAN Port :Yes; Network Protocol: RTSP/RTMP/ ONVIF, GB/T28181; Pan Rotation:+ 170° Tilt Rotation :-30°~+90° ; Pan Control Speed: 0.1~60°/second ;Tilt Control Speed : 0.1~30°/second ;Preset Speed: Pan: 60°/second, Tilt 30°/second ;Preset Number:255 preset; Preffred Make-ATDSC/SONY/Vaddio/Peoplelink

DSP SITC of Digital signal processor : Should have Double Core chip having 456MHz or better; Should have Microphone Inputs x 04 or more; Should have Microphone / Line outputs x 04 or more ; Should have Input processing’s with Preamp, Signal Generator, Expander, Compressor, 5-band parametric equalisation, Auto gain, AM auto mix function, AFC Adaptive Feedback Cancellation; Should have Output processing with Speaker management having 31-band graphic equaliser, delay, crossover, limiter, high and low channel filters; Should have Matrix Mixing of input and output signals, mixing component control or better; Should have Automatic Mixing Console ; Should have AFC Auto feedback elimination; Should have Auto Echo cancellation; Should have Auto Noise Cancellation module; Should have Automatic mixing console, Ducker, or better, Should have built-in USB as Microphone in and Audio out for Software based VC as well as for recording the conference and playing digital audio, Should have camera tracking for Look At Me / Speaker tracking, Should have minimum 8 GPIO ports free to configurable as required.; Should have Central Control Command Cet Generator ; Should have Sampling rate of 48Khz or better, Frequency response of 20Hz – 20Khz + 0.2dB or better, Should have input gain amplification of -24～27dB 3dB,Level 1 with minimum 7 levels or better; Should have background noise -90dBu or better ; Should have THD+N ≦0.004% @4dBu or better ; Should have Automatic power failure protection memory function; Should have per channel phantom power 48V module or better. ; Should have software which should be configurable PC and also through Mobile devices like Smart phones, Tablet etc. Should have password facility to avoid misuse having separate password for the admin and separate for users. Should have facility to save the different setting done in a file upto 100 or more settings. ; Should have Ethernet Port RJ 45 x 1; Should have RS 232 x 1; Should have RS 485 x 1. Preffered Make- ATDSC/YAMAHA/ Equipson/Peoplelink

Supply and installation of Cable & Connectors all as per direction of E/l.

Rack SITC of Fully Loaded 6U 19" 600*600 Wall Mounted AV Rack with all required accessories -2 Nos. of Fan,16A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; The Front frame should be integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 Preferred Make-Legrand /Netrack/ President/Valrack

Video SITC of rack-mountable 4K60 4:4:4 presentation system 04 HDMI®, two pairs of mirrored HDMI and DM Lite outputs with 4K60 scalers, and analog audio inputs and outputs.Should include support of HDR (High Dynamic Range) and Dolby Vision video formats, audio mixing, advanced EDID management, XiO Cloud connectivity, and enterprise-grade security.Ethernet for connectivity to network,USB for Programming; Preferred Make-Crestron/Extron/Lightware

Mic SITC of Corded Digital Deligates Units Gooseneck microphone with programmable switch . With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times , Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Immunity to mobile phone interference Make & Model is: Uniview- CCSD-DL./Harman/Televic

Mic SITC of Corded Digital Chairman Unit Gooseneck microphone with programmable switch With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Chaiman Button;Preferred Makel is :Uniview- CCSD-DL./ Harman/Televic

Controller SITC of Digital central conference controller with Built‑in MP3 recorder with internal memory and USB recording, Built‑in Digital Acoustic Feedback Suppression, Quick and easy connection upto 80 discussion devices, Native support for automatic HD camera control, Signal to noice :> 94 dBA, Frequency response for input :30 Hz to 20 kHz, Recording/ Playback (bit rate):64, 96, 128, 256 Kbit/sec, Nominal loudspeaker output:72 dB SPL and Functions such as: Plug-and-play functionality, Web browser control, Open microphone control, Built-in MP3 recorder, Discussion control Make & Model is: Uniview-CCSD-CURD/ Harman/Televic

Speaker SITC of wall mounted cabinet speaker 30 Watt includes mounting system Dual 4" 2‑Way Surface-Mount Loudspeaker,Compact full range,Ideal for Conference Halls, patios, and retail,Vented LF enclosure,1-inch titanium diaphragm HF driver with neodymium magnetic structure,Coherent Coverage Waveguide,Full-bandwidth overload protection (LF and HF),Elliptical weather-resistant ABS enclosure,Paintable black or white finish,Magnetically shielded for video applications,Strong-Arm Mount™ for easy, flexible aiming,"T" version for 70 or 100 V distributed systems with specifications of Frequency Range (-10 dB)- 65 Hz – 20 kHz, Sensitivity (SPL, 1 W/1 m)- 89 dB,Max. SPL/1m (calc.)- 115 dB,Power Handling (Continuous, Peak)- 100 W, 400 W,Transformer taps(transformer version only)- 70 V: 3.75 W,70 V/100 V: 7.5, 15, 30 W, Coverage, H x V- 120° x 80°, LF Transducer-Two 4", HF Transducer -1", Nominal impedance-(non-transformer version)- 8 Ω, ; Make- AKG/BOSE/EV

Headworn Wireless Mic SITC of Headworn Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz (Approved Makes: Audio Technica, Senheiser, Electro-Voice/AKG)

Cable Cubby Supply, Installation, Testing and Commissioning of Modular Cable cubby with fully Retracting Lid, aluminium black anodized cover, Consisting of 1 x HDMI retractable cable which retracts gracefully by simply lifting it vertically above the table, , 1 x LAN and 1 x 5 Amp Power Socket, Make - Magnum/Crestron/Karmer

Supplying, fitting & fixing of Rimless Blind installation Wall Hung WC with UF soft Close Seat Cover Hinges and Accessories set (Make Jaguar model number- DRS-WHT-37953 BIUFSM or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of 15mm brass 2 way Bib Cock for health faucet with wall Bib tap (Make Jaguar model number- DRC-CHR-37041 or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Health faucet with 1 Meter long Easy Flex Tube in Chrome Finish & wall Hook all complete as per engineer in charge.

Supplying, fitting & fixing of Toilet paper Holder Recessed Type (Stainless Steel) (Make Jaguar model number- AHS-1551 or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Metropole Flush valve Dual Flow 40mm Size (Concealed Body) with Exposed Shut off Provision & 100mm Square Plate (3.0/6.0 Lts Per Flushing) (Make Jaguar model number- FLV-1095NSQ or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Counter Top Basin (Make Jaguar model number-DRS-WHT-37601 or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Soap Dispenser with Glass bottel. (Make Jaguar model number- AKP-35735P or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Piller Cock of Single Lever Basin Mixer with Popup Waste & 450mm Long Braided Hoses (Make Jaguar model number- DRS-37051B or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Waste Coupling 32 mm Size Full Thread with 80 mm Height, Material of Waste Fitting- Leaded Tin Bronze conforming to Grade 2 of IS 318/1962 (Make Jaquar model number- ALD-709 or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Bottle trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange (Make Jaguar model number- ALD-769L300x190 or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Towel ring Square cast Brass (Make Prima model number- PIL-4504-G or equivalent) all complete as per engineer in charge.

Supplying, fitting & fixing of Angle Stop Valve(internally Threaded) (Make Jaguar model number- OPP-15053PM or equivalent) all complete as per engineer in charge.

Add GST 18 %

Add Labour cess 1%

JUNAID ENTERPRIES (BID ID -664280)

SUDHIR KUMAR SINGH (BID ID -664457)

BABAN SINGH (BID ID -664652)