Proposed Landscaping,Car Parking,Generator Shed , Main Entrance Gate & Beautification work in the campus of Judge's Guest House ,155 Chajjubagh, Patna

P/V labour for cleaning the site & uprooting trees etc all complete jobs.

Providing, driving and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified,excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 400 mm dia piles

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor.

Boring, Providing and installing bored cast in situ reinforced cement concrete piles of grade M-25 etc all complete

Earth work in excavation in foundation trenches etc all complete jobs.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content indesign mix is more than 110% of the specified minimum cement content,the contractor shall have discretion to either re-design the mix or bear thecost of extra cement.Concrete of M-25 grade with minimum cement content of 330 kg/cum

Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete.Concrete of M-25 grade with minimum cement content of 330 kg/cum

P/V PCC M15 (1:1.5:3) PCC in front in etc all comp job.

P/V PCC M15 (1:2:4) PCC in front in etc all comp job.

P/V RCC M20 (1:1.5:3) in F/P level etc all complete jobs.

P/V RCC M20 (1:1.5:3) in Stiffener & column slab and beam etc all complete jobs.

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

P/V 100A B/F soling in F/P level etc all complete jobs.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of Engineer-incharge.(The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330kg/cum.Excess/less cement used as per design mix is payable/ recoverable separately).

Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete.

Providing and laying in position bitumen hot sealing compound for expansion joints etc.Using grade 'A' sealing compound.

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

TMTC-500- 8mm dia .

TMTC-500-10 mm dia.

TMTC-500-12 mm dia.

TMT FE-500-16 mm dia.

TMT FE-500-20 mm dia.

P/V Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

P/V 100A designation brick work in cm (1:6) in S/S level etc all complete jobs.

P/V Fly Ash designation brick work in cm (1:6) in S/S level etc all complete jobs.

P/V 12mm CP(1:6) in wall etc all complete jobs

P/V 15 mm cement plaster on rough side of single or half brick wall of

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens,nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Neat cement punning

P/V 6mm CP(1:4) in ceiling etc all complete jobs.

Providing and laying integral cement based treatment for water . proofing on horizontal surfaces at all levels as directed by Engineer-in-charge and consisting of: 1) 1st layer of 20 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement:3 coarse sand) mixed with water proofing compund conforming to IS: 12645 in the recommnded proportion. Joints sealed and grouted with cement slurry mixed with water proofing compound conforming to IS: 12645 in proportions recommended by the manufacturer. II) 2nd'c!ass layer of 25 mm thick cement mortar 1:3 (1 cement:3 coarse sand) mixed with water proofing compound in recommended proportions. Ill) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreadidng @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Providing and laying water proofing treatment to vertical and horizontal

62 mm thick cement concrete flooring with metallic concrete hardener topping under layer 50 mm thick cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick metallic cement hardener consisting of mix 1:2(1 cement hardener mix:2 stone aggregate 6 rnrr.. ominal size) by volume hardning compound is mixed @ 2 liter per 50 kg of cement or as per manufacture specification. This includes cost of cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Providing and applying 2 mm thick wall putty of approved brand

Finishing wall with M/Deluxe paint for interior & exterior surface etc all comp jobs.

Wall painting with plastic emulsion paint of approved brand and

P/V and fixing M.S Grill etc all complete jobs.

P/V steel work in builtup tubular truss etc all complete jobs.

Providing & fixing all height level and location colour 0.56mm aluminium colour coated roofing sheet etc all compl.

Painting with ready mixed paint over New Steel surface etc all comp jobs.

Painting with ready mixed paint over old Steel surface etc all comp jobs.

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks,lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge: 80 mm thick c.c. paver block of M-35 grade with white colour design and pattern.

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms,vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and fixing 10 mm thick acid and / or alkali resistant tiles of approved make and colour using acid and / or alkali resisting mortar bedding, and joints filled with acid and / or alkali resisting cement as perIS : 4457, complete as per the direction of Engineer-in-Charge.

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc., for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Post and struts

Roof Slab

Suspended floors, roofs, landings, balconies and access platform

Stairs, (excluding landings) except spiral staircases.

Providing and fixing factory made uPVC white colour Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness(weight not less than 20 kg/sqm).

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.50 mm all complete.

Providing and fixing anodised aluminium grill (anodised

Providing and fixing pvc 110 mm dia pipe

Providing and fixing pvc 110 mm dia band

Providing and fixing pvc 110 mm dia tee with door

Providing and fixing pvc 110 mm dia Pipe clip

Providing and fixing cpvc 15 mm dia pipe

Providing and fixing cpvc 25 mm dia pipe

Providing and fixing cpvc 20 mm dia pipe

Vermi Compost

Potash

Neem Khali

Thimate

Roger