Estimate for Construction of SDO Residence on first floor at Electrical Sub Division, HPSEBL, Mashobra, District Shimla, (H.P). (Including structural design from approved design Engineer).

Amount

Part-I (Civil Work)

Preparation of detailed structural drawings for proposed SDO Residence building from authorised/registered structural Design Engineer.

Cutting in earth work and disposal of excavated earth upto a lead of 20 metres:- Pick Work & Jumper Work 50 %

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres. Pick Work & Jumper Work 50 %

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:

Foundation, footings basis of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto 200mm. In thickness.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Edges of slabs and breaks in floors and walls: Under 20 cm. wide.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :

Wall (any thickness but not less than 0.1 m thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto floor two level :

Lintels, beams girders bressumers and cantilevers upto floor two level :

Column, pillars, posts and struts upto floor two level :

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level : Tor Steel :

Half brick masonry in common burnt clay building bricks in :-Cement Mortar 1:4 (1 cement:4 sand) Second Class Bricks

Brick work using common burnt clay building bricks in foundation and plinth in :-Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks

White glazed tiles 6 mm thick in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3 sand) finished with flush pointing in white cement.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Providing and laying granite stone in flooring 20mm(average)thickness base of cement mortar 1:3 (1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position.2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws.35mm thick 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm fordoors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.30mm thick 2nd class deodar wood.

6mm Cement plaster to ceiling In Cement Mortar 1:4(1 Cement:4 Sand)

15mm cement plaster in two coats backing coat 10mm and finishing coat 5mm thick on fair side of brick masonry /stone masonry/concretewalls for interior plastering upto floor two level including arrises,internal rounded angles ,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth cement mortar 1:4 (1 Cement:4 Sand).

20mm Cement plaster in two coats,backing coat 15mm and finishing coat 5mm thick on rough side of brick/stone masonry walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and /or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar1:4 (1cement:4 sand).

Boulder filling dry hand packed under floors:-

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. 50mm thick.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with repainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charge

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/ facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars,ladders,railling,brackets and similar works.

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. 100mm dia pipes

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete PVC Plain bend 150mm dia

Providing and fixing m.s.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10x10x10 cm of 1:2:4:mix (1 cement 2 sand 4 stone graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the wall etc. 100 mm diametre for C.I. pipe

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with :-Readymixed primer

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.250x16mm

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete.

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth

Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 Sand : 12 Graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1 cement:6 sand) in breast walls and retaining walls.

Stone filling behind retaining walls

Providing and fixing 100 mm diameter pipe for weap holes for stone masonry wall.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.

Part-II (WS & Sanitary)

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (medium grade) tube fitting and clamps including making good the wall, ceiling and floor:- 15mm nominal bore.

Providing and laying in trenches, galvanized mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) :-15mm nominal bore

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres. Pick Work & Jumper Work 50 %Each

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete

I) 110 mm dia.

II) 75mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete.

I) 110 mm dia.

II) 75mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete.

I) 110 mm dia.

II) 75mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.

I) 110 mm dia.

II) 75mm dia

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete.

I) 110 mm dia.

II) 75mm dia

P/F PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 75 mm

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately):- Angle Indian Universal closet

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately. : Flat back type of size 430mm x 260 mm x 350mm.

P/F Vitreous China automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) :-

5 litres capacity

10 litres capacity

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers : SOLID TYPE: a) white plastic seat and cover

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings:- Flat back 630mmx450mm

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting. i) 610 x 460 mm with bowl depth 200 mm.

Providing and fixing C.P. Brass waste for wash basin or sink :- (ii) 32mm dia.

Providing and fixing M.I. Union for wash basin or sink :- 32 mm dia.

Providing and fixing 600mm x 450 mm beveled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws :- (ii) 600mm x 20mmm

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws :- (i) Glass container

Providing and fixing CP brass tap with capstan head Bib tap 15 mm nominal bore.

Pillar tap 15 mm nominal bore.

Providing and fixing brass full way valve with wheel:- (a) 15mm nominal bore

Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe.

Providing and fixing P.V.C connection with brass unions :- (a) 300/450mm length :- (i) 15mm nominal bore

Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass racket nd guard rail complete, fixed to wooden plugs with C.P. Brass screws

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws :-

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete.

I) 110 mm dia.

II) 75mm dia

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :- ii) 1000 litres net capacity tank.

Constructing chamber 600mm x 600mmx750mm inside size for fire hydrants with C.I. surface box 350mmx550mm top and 165 mm deep (inside) with changed lid and RCC top slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 100mm thick foundation concrete 1:5:10 ( 1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete :-With 150 mm thick walls of reinforced cast in situ plain cement concrete walls in 1:2:4 mix (1 cement:2 sand : 4 grades stone aggregate 20 mm nominal size complete with form work and reinforcement with 6mm bars not exceeding 150 mm centres both ways

Boulder filling dry hand packed under floors:-

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. 1310101 40mm thick.

UNIVERSAL TRAINING & RESEARCH INSTITUTE SHIMLA

Balbir Singh Rathore