Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹47,200Accepted-Finance 110 MINI SHOPPING COMPLEX NEHRU MARKET JAMMU | ₹47,200 | L1 | Accepted-Finance lowest |
| 2 | L2₹48,250+₹1,050 (2.22%)Rejected-Finance BHAGWATI NAGAR JAMMU | ₹48,250+₹1,050 (2.22%) | L2 | Rejected-Finance not lowest |
| 3 | L3₹53,500+₹6,300 (13.3%)Rejected-Finance HOUSING COLONY UDHAMPUR | UDHAMPUR | JAMMU AND KASHMIR | 182101 | ₹53,500+₹6,300 (13.3%) | L3 | Rejected-Finance not lowest |
| Sl No | Description | Qty | Unit | Rishabh Electricals and Mechanical Works L1 | BEE AAR ENTERPRISES L2 | M.S J K HYDRAULIC ENGGG AND FABRICATOR WORKS L3 |
|---|---|---|---|---|---|---|
| 1.00Repairs to 5 cusec x 11.5 mtr head Horizontal split casing pump of unit-III along with allied works at LIS Jandi. | ||||||
| 1.01 | Disconnecting electric power supply and decoupling of 5 cusec x 11.5 meter head discharge pump unit no III from 40 hp motor and then dismantling the pump and motor from the base frame. Carriage & shifting of dismantled pump on head load to roadside using manual labour and then to workshop by carriage vehicle.
Repair to 5 cusec x 11.5 meter discharge split casing pump of pumping unit no III of Lift irrigation station, Jandi at workshop by dismantling and extraction of all worn out/damaged parts i.e. pump shaft, impeller, bearings, sleeves, bush, check nuts, nuts & bolts, gland plate, gland studs. Properly cleaning the internal surface of pump casing. Remetalling /brazing of pump shaft and turning to bearing size and threading at positions of check nuts. Repairs to impeller by filling cavities, cracks and finishing to original size. Providing and fitting 2 no’s of new bearings on driving and non driving end of the pump, 1 no’s neck rings, 2 no’s shaft protection sleeves, 1 no’s check nuts, nuts & bolts, fabrication of 1 no’s new gland plate with providing and fitting of 2 no’s new gland studs on ends of pump. Repair to bearing housing on driving end of pumping unit by providing and fitting of bush, turning and fitting of bush to make inner diameter of bearing housing suitable for fitment of bearing. Reassembling all parts of pump with proper greasing of bearings and providing and fitting of gasket sheet between upper and lower part of the pump. Providing and fitting of graphite packing of suitable size on both ends of the pump and 2 kg spare at Station for routine use.
Repair to 250 mm foot valve of pumping unit no III by way of dismantling parts. Cleaning of all internal parts to remove silt and rust. Fabrication of new foot valve plate as per size, new leather washer, hinge pin, new nuts & bolts. The job includes fabrication of strainer to stop entry of unwanted material and fitting it with foot valve.
Job includes replacement of old damaged 1 no. ball valve of priming pipe for Unit no. III by way of providing and fitting CI ball valve of 50 mm dia.
The job also includes minor repairs to 3 no. doors of the pump room by way of providing and welding door latches, hinges, handles, tower bolt of required sizes at LIS jandi
The job includes loading, un-loading, manual labour, carriage charges of vehicle (to & fro), tools & tackles, welding set charges , cost of materials, installation & testing charges at site.
Note: The tenderers are requested to visit the site and quote the rate as per site conditions. The firm should offer rebate on old material. | 1 | Job | 47,200 ₹47,200 Lowest | 48,250 ₹48,250 | 53,500 ₹53,500 |
| 1.02 | Rebate on Old Parts | 1 | Job | -950 ₹-950 | -483 ₹-483 | -535 ₹-535 |
Tender Value
₹67,000
EMD Value
₹1,340
Closing Date
1 Jun 2026, 12:00 pmClosed
XEN MID JAMMU
MID JAMMU
enot 20 dated 25 may 2026
2026_IFC_310954_1
MID/J/e-NIT/2026-27/20
Open Tender
Repair and Maintenance Works
Item Wise
10 days
jandi
as per tender notice and sbd
8 documents required · 8 mandatory
₹200
Executive Engineer MID JAMMU
₹1,340
12 Jun 2026
25 May 2026
2 Jun 2026
25 May 2026
1 Jun 2026
25 May 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Repairs to 5 cusec x 11.5 mtr head Horizontal split casing pump of unit-III along with allied works at LIS Jandi. | |||||
| 1.01 | Disconnecting electric power supply and decoupling of 5 cusec x 11.5 meter head discharge pump unit no III from 40 hp motor and then dismantling the pump and motor from the base frame. Carriage & shifting of dismantled pump on head load to roadside using manual labour and then to workshop by carriage vehicle.
Repair to 5 cusec x 11.5 meter discharge split casing pump of pumping unit no III of Lift irrigation station, Jandi at workshop by dismantling and extraction of all worn out/damaged parts i.e. pump shaft, impeller, bearings, sleeves, bush, check nuts, nuts & bolts, gland plate, gland studs. Properly cleaning the internal surface of pump casing. Remetalling /brazing of pump shaft and turning to bearing size and threading at positions of check nuts. Repairs to impeller by filling cavities, cracks and finishing to original size. Providing and fitting 2 no’s of new bearings on driving and non driving end of the pump, 1 no’s neck rings, 2 no’s shaft protection sleeves, 1 no’s check nuts, nuts & bolts, fabrication of 1 no’s new gland plate with providing and fitting of 2 no’s new gland studs on ends of pump. Repair to bearing housing on driving end of pumping unit by providing and fitting of bush, turning and fitting of bush to make inner diameter of bearing housing suitable for fitment of bearing. Reassembling all parts of pump with proper greasing of bearings and providing and fitting of gasket sheet between upper and lower part of the pump. Providing and fitting of graphite packing of suitable size on both ends of the pump and 2 kg spare at Station for routine use.
Repair to 250 mm foot valve of pumping unit no III by way of dismantling parts. Cleaning of all internal parts to remove silt and rust. Fabrication of new foot valve plate as per size, new leather washer, hinge pin, new nuts & bolts. The job includes fabrication of strainer to stop entry of unwanted material and fitting it with foot valve.
Job includes replacement of old damaged 1 no. ball valve of priming pipe for Unit no. III by way of providing and fitting CI ball valve of 50 mm dia.
The job also includes minor repairs to 3 no. doors of the pump room by way of providing and welding door latches, hinges, handles, tower bolt of required sizes at LIS jandi
The job includes loading, un-loading, manual labour, carriage charges of vehicle (to & fro), tools & tackles, welding set charges , cost of materials, installation & testing charges at site.
Note: The tenderers are requested to visit the site and quote the rate as per site conditions. The firm should offer rebate on old material. | - | Job | - | - |
| 1.02 | Rebate on Old Parts | - | Job | - | - |
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.40 MB
BOQ_1006223.xls
BOQ • 0.29 MB
SBD20.pdf
Additional Documents • 0.66 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .