SPECIAL REPAIRS TO CUPBOARD AND JOINERY IN JCOS BLOCK AND ORS BLOCK OF MD ACCN OF VASASNTH ENCLAVE UNDER GE NORTH BANGALORE

Amount

S & F in repairs 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, fixed in kitchen Cabinet or cupboards all as specified.

M & L for external teak wood lipping, 6mm thick fixed with nails to 18/19mm thick prelaminated particle board complete all as specified and directed

M&L for Plain fillets square, rectangular or triangular in section clean sawn , secured with nails or brads of second class hard wood fixed to cupboard shutter including taking down old fillets exc 6 & n exc 13 sqcm cross section area in framed work all as specified and directed.

S&F Continuous (piano) hinges 30mm width of flaps (when open) , mild steel, bright finish or electro galvanised complete all as specified and directed

S&F 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws /fixed in repairs.

S&F Magnet door catcher with main magnet body of stainless steel including iron striking plate of size 60x30x10 mm in size complete all as specified and directed

S & F 40 mm dia cupboard knobs fixed with nut, screw and washer of Brass,polished complete all as specified and as directed.

S&F in repairs stainless steel curtain rod of 15 mm dia (weight not less 200 gms per running meter) incl etc complete all as specified and as directed

S&F in repair Bracket for curtain rod of dia 15 mm made out of stainless steel Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed

M & L for ATT At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same etc complete all as specified and as directed

Taking down chowkhat (without taking of shutter from the frame) not exc 1.5 sqm each including all iron mongeries complete all as specified and directed

As per Item No 11 above, but exc 1.50 sqm and not exc 4.00 sqm each

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each all as specified and as directed

M & L for Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, including treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

S&F Flush door shutters 35mm thick, factory made as per IS:2202 (Part-I 1999) solid core construction, with block board core and plywood face panels, commercial type on both sides as per drawing fixed to chowkhats all as speified and directed

S&F 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed Note: Supply and fixing of wire mesh will be measured and paid separately under relavent item.

M & L for plain cement concrete for filling of steel door frame/box type steel window/vent type C0,1:3:6 using 12.50mm graded stone aggregate.

M & L for plain cement concrete for filling of hold fast of door frame window/vent type B1,1:2:4 using 20mm graded stone aggregate.

M&L preparing new wooden surface of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

M & L applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of new steel surfaces

S & F Butt hinges medium weight, cold rolled mild steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

S&F 150 mm long Mild steel pressed handles, oval type, stove enamelled black etc complete all as specified and as directed

S&F 200 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed etc complete all as specified and as directed

S&F Mild steel sliding door bolts 250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed to steel door complete all as specified and directed

S&F mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete

Supply and fix stainless steel wire cloth 0.36mm nominal dia and average width of aperture 1.40mm and fixed with tinned tack or galvanized wire staple all as directed fixed.

Taking down cement plaster of any description including racking out joints, hacking for key and disposal of debris to out side MD land all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished plastered surface even and smooth without using extra cement

M&L Preparation of newly plastered surfaces and applying two coat of oil bound distemper over a coat of alkali resistent primer over one coat of 3 mm thick wall care putty on plastered surfaces of walls including in narrow widths/ bands etc complete all specified and as directed.

Eeguchi Constructions

S S BUILDERS