REPAIR TO PATH DRAIN CULVERT COMPOUND WALL GATE JAFRI WALL SEWAGE LINE, REPAIR REPLACEMENT OF SEPTIC TANK ETC OF UNRESTRICTED AND RESTRICTED AREA OF CQA W CQA OFV SQAE A SQAE L AND NAI DGQA UNITS UNDER GE P NO 1 JABALPUR

Amount

UN-RESTRICTED AREA:- Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground embeded in concrete or brick work complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft /loose soil , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, n exc 10 sqm on plan and n exc 1.5m in depth and getting out any type of soil complete all as specified and directed.

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25cm complete all as specified and directed.

Removing excavated material n. exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls and including wall tiles etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings with ridge complete all as specified and directed.

M & L for Cement concrete type D-2 1:4:8 (using 20 mm graded aggregate) as in foundation filling and mass concrete , sub base complete all as specified and directed.

S&F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;MS angle iron in "Y" shape posts and struts in fencing including cutting tops to shape as directed including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing and incl steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hnging door fittings and fixing complete conferming to gde Fe 410-w complete all as specified and directed.

S & F in repair chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed

S&F in repair Concertina Coil of 600 mm dia of Approved Type/Make for laying on Y shape angle fixed on boundry wall etc complete complete all as specified and directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

All as per above item No. 19 here-in-before but except brick complete all as specified and directed. Note:- Old brick shall be re-used retrived from Item No. 7 above.

M&L for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for preparation of newly/old plastered wall surfaces including brooming down or steel wire brushes, scraping down smoke soot moulds, moss and effeorescent salts and trading oil and greasy spots and applying one coat of cement based paint complete all as specified and directed.

M & L applying three coat of white wash on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, plinth courses etc and similar work including necessary form work complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 6 to 8mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for RCC type B 1, 1:2:4 (20mm graded agg) as in columns, pillars, piers, posts, beam, slab, chajja, footing etc complete all as specified and directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams,column,slab, and similar works; vertical or to batter complete all as specified and directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & attern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed.

M&L for 16 to 18 mm thick granite stone slab of any type with table rubbed and polished in cooking platforms and like set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces over 10cm in width or girth and applying two coats of syanthetic anamel paint over one coat of red oxide complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces , complete all as specified and directed.

M & L for Providing 35mm thick (measured solid), precast cement concrete louvres and jallies, with 1:2:4 mix, type B0 including all mouldings but excluding frame set in CM (1:6) complete all as specified and directed.

M & L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L Pre-painted galvatume aluminium zinc coating GI based corrugatged steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters, fixed with angle cleats or other connecting plates of Gde fe 410-0 or fe 250-0 complete all as specified and directed.

M&L for vitrified paver color tiles 400 x 400 ,10 to 12 mm thick, moulded set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

RESTRICTED AREA:- Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft /loose soil , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, n exc 10 sqm on plan and n exc 1.5m in depth and getting out any type of soil complete all as specified and directed.

Demolition of cement concrete reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

Demolition of reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25cm complete all as specified and directed.

Removing excavated material n. exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls and including wall tiles etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Dismantling of asbestos cement (corrugated, sem-icorrugated, etc.) sheets in roof coverings complete all as specified and directed.

M & L for Cement concrete type D-2 1:4:8 (using 20 mm graded aggregate) as in foundation filling and mass concrete,sub base complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing and incl steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hnging door fittings and fixing complete conferming to gde Fe 410-w complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

All as per above item No. 52 here-in-before but except brick complete all as specified and directed. Note:- Old brick shall be re-used retrived from Item No. 44 above.

M&L for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed

M & L applying three coat of white wash on newly/old plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, plinth courses etc and similar work including necessary form work complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 6 to 8mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & attern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed.

M&L 16 to 18 mm thick granite stone slab of any type with table rubbed and polished in cooking platforms and like set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces over 10cm in width or girth and applying two coats of syanthetic anamel paint over one coat of red oxide complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces , complete all as specified and directed.

M&L Pre-painted galvatume aluminium zinc coating GI based corrugatged steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters, fixed with angle cleats or other connecting plates of Gde fe 410-0 or fe 250-0 complete all as specified and directed.

M&L for vitrified paver color tiles 400 x 400 ,10 to 12 mm thick, moulded set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

Deduct schedule of credit amount Rs. 76940.00 to be deducted during AOC

M/S A.P.M. CONSTRUCTION CO. (BID ID -3341546)

R R VISHWAKARMA CONSTRUCTION CO (BID ID -3337288)

SR ASSOCIATES (BID ID -3338807)