Utility shifting of distribution and rising pipe line of Sosai rural pipe water supply scheme across and along due to road widening of NH-75 Ranchi- Kuru road in Mander block under D.W. and S. Division, Ranchi West on turnkey basis.

Amount

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 100mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-9 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance, and one no. gasket with each pipe, including inspection charges of DGS&D/SGS and sales tax all complete. [JH-DWSD-SOR - Sl. No. 110]

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Volume of Excavated earth in pipline trenches

A ) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge (Classification soil item B) - 70% of excavated earth. [JH-DWSD-SOR-3.1.1.1

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country sode) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I. - 30% of excavated earth. [JH-WRD-SOR-6.1.11.2

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge. [JH-DWSD-SOR- 3.1.1.2] 80% of Earth work excavation Qty.

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying without rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I. [JH-DWSD-SOR- 3.1.32(B)

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Providing and supplying air valve as per IS-10845-2000 and MJP's standard specification of approved make & quality of following diameters including all taxes ( central and local), railway freight, insopection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores / sites unloading and stacking etc. complete.depatmental [MJP Sec. - I - (XIII) - 5 b] PN-1.6

40mm dia

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. ( for all class of valves.) [MJP Sec.- I - (XIII) -10]

40mm dia

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. all complete. [JH-DWSD-SOR- Page no. 60 Without byepass arrangement (With ED)] PN - 1.6

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.). [JH-DWSD-SOR- 3.1.35]

Supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge. [JH-DWSD-SOR- 3.1.46]

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Labour cost for one cutting of D.I Pipes & specials including supplying, necessary tools and plants, chipping or filling the surface finish as per spercification and direction of E/I. [JH-DWSD-SOR- 3.1.43]

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight. [JH-DWSD-SOR-Chapter-1, Sl. No. 108-A(a)] Including C.P., take 5% of item no. 1

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines.

i) Pucca Road cutting- 40% of 462.7 [JH-DWSD-SOR- 3.1.19.1A]

ii) W.B.M. Road cutting- 30% of 462.7 [JH-DWSD-SOR- 3.1.19.1B]

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I. [JH-BCD-SOR- 5.10.2]

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/I. [JH-BCD-SOR- 5.3.2]

Supplying all materials, labours tools for construction of brick massonary S.V. chamber of size 1.20 x 0.90 (I.D) & 1.50m deep as per standard specification.

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 100mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-7 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance, and one no. gasket with each pipe, including inspection charges of DGS&D/SGS and sales tax all complete SOR page No.43 Sl. 110

100 mm dia pipe

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Volume of Excavated earth in pipline trenches

A) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge (Classification soil item B) - 70% of excavated earth. [JH-DWSD-SOR-3.1.1.1

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country side) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I. - 30% of excavated earth. [JH-WRD-SOR-7.1.12.2]

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge. [JH-DWSD-SOR- 3.1.1.2]

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying without rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I. [JH-DWSD-SOR- Page No. 167]

100 mm dia pipe

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight. [JH-DWSD-SOR-Chapter-1, Sl. No. 108-A(a)] Including C.P., take 10% of item no. 1

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. all complete. [JH-DWSD-SOR- Chapter-1, Sl. No.- 119-B Without byepass arrangement (With ED)] PN - 1.0

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.). [JH-DWSD-SOR- 3.1.35]

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines.

i) Pucca Road cutting- 40% of 960 [JH-DWSD-SOR- 3.1.19.1A]

ii) W.B.M. Road cutting- 30% of 960 [JH-DWSD-SOR- 3.1.19.1B]

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I. [JH-SOR-5.10.2]

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/I. [JH-BCD-SOR- 5.3.2]

Supplying all materials, labours tools for construction of brick massonary S.V. chamber of size 1.20 x 0.90 (I.D) & 1.50m deep as per standard specification.

Labour charges for one cutting Pipes including supplying necessary tools & plants as per specification. [JH-DWSD-SOR- 3.1.43]

100 mm dia pipe

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge. [JH-DWSD-SOR- 3.1.46]

100 mm dia pipe

150 mm dia pipe

200 mm dia pipe

250 mm dia pipe

Providing, installing and giving satisfactory field testing of flanged ends Bulk water meter of following type and as mentioned below with FGI-250 cast iron body class"B" confirming to IS : 2373 or as per ISO-4064/4046, marked to read in metric system, alongwith manufacturer's test and guarantee certificate including cost of all materials and labour with ISI mark or EEC mark.

Carriage of materials

Take 10% of item no. 10

Manufacturing providing and supplying spirallly welded / ERW / SAW / Fabricated M.S Pipe ( Commercial quality) including procuremnet of plates, Gas cutting to required size rolling, track welding assembling in suitable lenghs to form pipes, welding on automatic welding machine and forming 'V', edge on both ends of pipe including all taxes (Central and local), railway freight, insurance unloading from railway wagon, loading into truck, transport to stores / site, unloading, staking, etc. complete as per I.S 3589/I.S 5504 as applicable as per specifications (no negative tolerence in thickness is permissible). MJP Section I-(XIV) MS Pipes 2.b.iii Page No. 166

300mm dia M.S pipe 7.1mm thick

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. P-150

PN 1.6 - 50mm MJP page 150

Providing Double flanged sluice valve (size 50mm to 1200mm) confirming for IS-2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, cap including all taxes transportation etc. complete.

150mm dia sluice valve P.N 1.6 [JH-DWSD-SOR-Chapter-1, Sl. No. 120 C Without byepass arrangement

Providing and appyling one coat of zinc rich appoxy primer to coat internal surface of pipe line at size . all compete job as per directuon of engineer in charge (Outer Surface) 25.0 Mtr. [MJP Sec. - I - (XVII) -19] Pro

LABOUR COST

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 M including all lifts levelling ramming the findation trenches removing roots of treesm shrubs all complete for driving pit as per direction of E/I. [JH-WRD-SOR-5.1.10.2]

Installation of product pipe by guided Auger Boring method including making of entry and exit pits, all related civil works like excavation, shoring/strutting, etc., shielded excavation through auger boring process, lowering of pipe segments in the jacking pit, laying and jointing of product pipeline thriugh process from the jacking pit and restiration of site after project completion as per the instructions of Engineer-in-Charge all complete except the cost of pipe. SOR -JKD- DWSD- page no. 57

Average cover of 1.5m depth below G.L. (upto 100 meter installation length) SOR page No. 59 Length = 25 M

Providing coarse clean sand filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materilas labour, royalty and taxes all complete as per building specification & direction of E/I. ( rate taken by SOR Jharkhand 5.1.10

Providing designation 75A one brick flat soiling joints filled with local sand includng cost of watering taxes royalty all complete as per building specification & direction of E/I. SOR Jharkhand 5.6.1

Providing P.C.C M-100 with normal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50mm to 25mm size) and clean coarse sand FM 2.5 to 3 including csreening shuttering mixing cement concrete inposition, vibratingm curing all taxes and royalty etc. all complete as per direction of E/I. For reception and thirst bed. Jharkhand SOR 5.3.3 Below Pipe 25.0 M x 1.0 M x 0.10 M = 2.50 M2 'Reception & Driving pit

Earth fillig in foundation and plinth in layer not exceeding 15mm thick well watered, rammed fully compact and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M reception and thirst bed. Jhrkhand SOR 5.1.7

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.). [JH-DWSD-SOR- 3.1.35]

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. ( for all class of valves.) [MJP Sec.- I - (XIII) -10]

Manufacturing providing and supplying spirallly welded / ERW / SAW / Fabricated M.S Pipe ( Commercial quality) including procuremnet of plates, Gas cutting to required size rolling, track welding assembling in suitable lenghs to form pipes, welding on automatic welding machine and forming 'V', edge on both ends of pipe including all taxes (Central and local), railway freight, insurance unloading from railway wagon, loading into truck, transport to stores / site, unloading, staking, etc. complete as per I.S 3589/I.S 5504 as applicable as per specifications (no negative tolerence in thickness is permissible). MJP Section I-(XIV) MS Pipes PAGE NO 166 350mm dia M.S pipe 7mm thick

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. PN 1.6 - 50mm MJP page 150

Providing Double flanged sluice valve (size 50mm to 1200mm) confirming for IS-2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, cap including all taxes transportation etc. complete.

200mm dia sluice valve P.N 1 [JH-DWSD-SOR-Page 60 Without byepass arrangement

Providing and appyling one coat of zinc rich appoxy primer to coat internal surface of pipe line at size . all compete job as per directuon of engineer in charge (Outer Surface) 25.0 Mtr. [MJP Sec. - I - (XVII) -19] Pro

LABOUR COST

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 M including all lifts levelling ramming the findation trenches removing roots of treesm shrubs all complete for driving pit as per direction of E/I. [JH-WRD-SOR-5.1.10.2]

Installation of product pipe by guided Auger Boring method including making of entry and exit pits, all related civil works like excavation, shoring/strutting, etc., shielded excavation through auger boring process, lowering of pipe segments in the jacking pit, laying and jointing of product pipeline thriugh process from the jacking pit and restiration of site after project completion as per the instructions of Engineer-in-Charge all complete except the cost of pipe. SOR -JKD- DWSD- Page 57 Average cover of 1.5m depth below G.L. (upto 100 meter installation length) Length = 25 M

Providing coarse clean sand filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materilas labour, royalty and taxes all complete as per building specification & direction of E/I. ( rate taken by SOR Jharkhand 5.1.10

Providing designation 75A one brick flat soiling joints filled with local sand includng cost of watering taxes royalty all complete as per building specification & direction of E/I. SOR Jharkhand 5.6.1

Providing P.C.C M-100 with normal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50mm to 25mm size) and clean coarse sand FM 2.5 to 3 including csreening shuttering mixing cement concrete inposition, vibratingm curing all taxes and royalty etc. all complete as per direction of E/I. For reception and thirst bed. Jharkhand SOR 5.3.3 Below Pipe 25.0 M x 1.0 M x 0.10 M = 2.50 M2

Earth fillig in foundation and plinth in layer not exceeding 15mm thick well watered, rammed fully compact and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M reception and thirst bed. Jhrkhand SOR 5.1.7

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.). [JH-DWSD-SOR- 3.1.35]

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. ( for all class of valves.) [MJP Sec.- I - (XIII) -10]

Manufacturing providing and supplying spirallly welded / ERW / SAW / Fabricated M.S Pipe ( Commercial quality) including procuremnet of plates, Gas cutting to required size rolling, track welding assembling in suitable lenghs to form pipes, welding on automatic welding machine and forming 'V', edge on both ends of pipe including all taxes (Central and local), railway freight, insurance unloading from railway wagon, loading into truck, transport to stores / site, unloading, staking, etc. complete as per I.S 3589/I.S 5504 as applicable as per specifications (no negative tolerence in thickness is permissible). MJP Section I-(XIV) MS Pipes .PAGE NO 166

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete.

Providing Double flanged sluice valve (size 50mm to 1200mm) confirming for IS-2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, cap including all taxes transportation etc. complete.

250mm dia sluice valve P.N 1.6 [JH-DWSD-SOR- Page No. 61 Without byepass arrangement

Providing and appyling one coat of zinc rich appoxy primer to coat internal surface of pipe line at size . all compete job as per directuon of engineer in charge (Outer Surface) 25.0 Mtr. [MJP Sec. - I - (XVII) -19] Pro

LABOUR COST

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 M including all lifts levelling ramming the findation trenches removing roots of treesm shrubs all complete for driving pit as per direction of E/I. [JH-WRD-SOR-5.1.10.2]

Installation of product pipe by guided Auger Boring method including making of entry and exit pits, all related civil works like excavation, shoring/strutting, etc., shielded excavation through auger boring process, lowering of pipe segments in the jacking pit, laying and jointing of product pipeline thriugh process from the jacking pit and restiration of site after project completion as per the instructions of Engineer-in-Charge all complete except the cost of pipe. SOR -JKD- DWSD- Page no 58

Providing coarse clean sand filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materilas labour, royalty and taxes all complete as per building specification & direction of E/I. ( rate taken by SOR Jharkhand 5.1.10

Providing designation 75A one brick flat soiling joints filled with local sand includng cost of watering taxes royalty all complete as per building specification & direction of E/I. SOR Jharkhand 5.6.1

Providing P.C.C M-100 with normal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50mm to 25mm size) and clean coarse sand FM 2.5 to 3 including csreening shuttering mixing cement concrete inposition, vibratingm curing all taxes and royalty etc. all complete as per direction of E/I. For reception and thirst bed. Jharkhand SOR 5.3.3 Below Pipe 25.0 M x 1.0 M x 0.10 M = 2.50 M2

Earth fillig in foundation and plinth in layer not exceeding 15mm thick well watered, rammed fully compact and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M reception and thirst bed. Jhrkhand SOR 5.1.7

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.). [JH-DWSD-SOR- 3.1.35]

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. ( for all class of valves.) [MJP Sec.- I - (XIII) -10]

Earth work in excavation in foundation trenches in hard soil (Vide Classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr. including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I. (DWSD-3.1.1.1)

Providing and supplying High Density Polyethylene pipe (HDPE pipe) of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074 materials rates are Ex-factory excluding transportation, taxes and duties. PE-80 , PN- 10 (DWSD 112m 1028)

Lowering, Laying and Jointing H. D. P. E./M. D.P. E. pipes in proper position including all specials by compression fitting/electro fusion and butt fusion jointing procedure as per relevant IS Code complete with all materials for jointing procedure like Electro fusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II. MJP 19-20 sec-I-IX sl no -2(i)

Providing 15 mm dia. G.I. pipe Tata or equivalent make as per IS 1239 (Part 1/2004) ISI Mark /medium quality in Stand Post. DWSD Sl. 9K (including CP+OHC)

Supplying all materials , labour and tools for fixing 15 mm dia G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketed joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of Engineer-in-Charge. DWSD 3.1.2(i)

Supplying and fixing G.I. fittings of approved make all complete as per specification and direction of E/I. DWSD 3.1.13

(1) Elbow

(a) 15 mm dia.

(3) Reducer Socket -

(a) 20 x 15 mm dia.

(4) Nipple -

(a) 15 mm dia.

(6) Plain Socket -

(a) 15 mm dia.

Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main Including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dm ferrule weight not less than 425 gram. (JOSR DWSD 3.1.4.1)

Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socket all complete as per specification and direction of E/I. DWSD 3.1.5.2

15 dia and weight not less than 400 Gm

Supplying materials , labours and equipments for construction of 0.90M x 0.90 M size P.C.C. (1:2:4) Rectangular Platform with stand post in house including 12 mm thick cement plaster in C.M. (1:4) with neat cement punning over exposed surface all complete job, as per approved design, specification and direction of E/I. (As per Annexure II Attached)

1.20 M x 0.90 M size P.C.C. (1:2:4) Rectangular Platform -

Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge.

Providing fitting & fixing 32 mm to 50 mm service HDPE saddle all complete job, as per approved design, specification and direction of E/I. (From olde Model estimate)

Add 18 % GST

Add Labour Cess @1% of Estimated Cost

OMPRAKASH J. CHAUDHARY (BID ID -663703)

GANPATI BORWELL AND CONSTRUCTION CO. (BID ID -663687)