REPAIR/REPLACEMENT OF PVC FLOORING TILING WORKS ALUMINIUM/WOODEN JOINERY RAILING CEILING WORK TILING PLASTERIG PLUMBING AND SANITARY WORK IN SOK OFFICE INS ABHIMANYU NAD DSC COMPLEX JETTY BLDG MES BLDG NAI FODC AND NBCD HARD AT NAVAL STATION KARANJA

Amount

Dismantling plain or corrugated steel sheeting ,any gauge ,thickness incl Nainital or similar pattern roof covering as specified and as directed

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tenstile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified and as directed

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of an colour having tenstile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified and as directed

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface and removal outside the MOD land, complete all as specified and as directed by Engr-in-charge. Note :- 1. Taking down earthing strips incl insulators from roof for treatment and re-fixing of same with existing specification in the same position after laid APP membrance including replacement of broken insulators, PVC rawl plus & screws etc are deemed to be inclusive of rate quoted by the contractor. 2. Unit rate quoted shall also include for removal of PVC water storage tank wherever existing carefully and refixing at the same or other position after completion of roof repair work 3. APP work shall be carried out on PENT RCC roof at 12 -15 mtr height (non accessible roof).

Demolition in cement concrete ground floor and paving nexc. 15 cm thickness (below above ground floor ) all as directed by Engr-in-Charge.

M&L PCC (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in padding to roof/chajja to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L water proofing treatment of roof consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified. (c) A layer of 4mm thick APP polymeric membrane of weight not less than 4.80 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Supply only water proofing liquid compoundcomplete all as specified and directed by Engr-in-Charge. :Make : DR. FIXIT PIDE PROOF LW, CICO, FOSROC.

M&L Appling one coat Bitumen water proofing aluminium heat resistance paint @ 0.10 kG/ Sqm over one coat of primer on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge. Make : PLASCON/PLASCON or equalant

M&L using ready Mix plaster for rendering 15 mm thick cement plaster in CM (1:3) on roof top surface including WPC as per manufacture's instruction or @ 3% by weight of cement on concrete surfaces, complete all as specified and as directed. Note : WPC will be measured separately

M&L for cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames exc 1.5sqm but n.exc 4 sqm each but with shutter (without taking off shutter from the frame) complete all as specified and as directed

-ditto- as per Item No.12 above but n.exc 1.5 sqm complete all as specified and as directed

Taking down shutters of any description exc 1 Sqm but nexc 2 sqm complete all as specified and directed.

S&F IInd class hard wood plain solid, straight, chowkats and frames wrought framed rebated on the solid , rounded or chamfered put together with glue pinned at joints.

S&F 35mm thick second class hard wood, plain framed, paneled shutter (Two panel) of 9mm BWP comercial ply or 12mm veneered particle board with comercial veneering on both faces the size of rail land stile as per IS 1003 (Part-I) killn seasoned and chemically pressure treated .

S&F solid PVC door frame of size 50mmx 47mm made out of 5mm wood grains printed PVC sheet reinforced with ms square tube and edges painted to match with printed sheet complete all as specified.

S&F factory made solid panel PVC door shutter 30 mm thick (styled) consisting of frame made out of MS tube for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ,C" channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheet for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet bedding and jointed together with solvent cement supplying and fixing in the frame at site all as specified and directed.

S & F extruded aluminium alloy handles fabricated type anodized 150 mm size.

S&F mild steel work, Grade Fe-410-0 or Fe- 310-0, as in flat iron (for holdfast) complete all as specified and as directed.

M&L mild steel Butt hinges medium weight, cold rolled and fixed 100 mm long .

S&F 200mm long aluminium anodized barrel tower bolts of extruded sections complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet cost of extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

M & L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M & L PCC 1:3:6, type C1 (using 20 mm graded agg) coping or filling for hold fast without using extra cement complete all as specified and directed.

M&L Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

S&F aluminium door/window/ventilator/partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc; complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, hooks & eyes, peg stays and handles including connected items, with and including rubber beading for 4 or 5mm thick glass, making good to the disturbed portion with its original specifications, complete all as specified and directed.

S&F concealed star lock powder coated for aluminium window fixed as per manufacturers instructions all as specified and directed.

M&L Hacking out old broken glass ( any thickness, size, quality or description ) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

M&L for 12mm thick vertical toughened glass as in door shutters/partition with and including stainless steel SS-304 patch fittings fixed with Anchor fastener, cutting to shape, drilling holes as required and all edges of glass shall be diamond polished. complete all as specified and directed.

M&L 4 mm thick plain glass sheets ordinary quality in any size, each pane fixed with rubber beading or oil putty for windows/doors/partition etc all as specified and directed.

S & F rough cast wired glass 6.40 mm thickness and glazing with rubber beading or oil putty for windows/doors/partition etc all as specified and directed.

S&F aluminium anodized grill of design DG 104 pattern made out of 10mm dia rod Fixed with and including standard aluminium frame of F section of size 23.40mmx15.30mm &1.4mm thick all as per manufactures instructions complete all specified & directed. Make of grill Deco grill or equivalent

M & L in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick alum,inium alloy sheet foundation box, main ody with stainless steel cover, governing pivot made of brass, other plart made of mild steel heavy duty and fixed.

S & F in repair for aluminium (extruded section) body hydraulically door closer regaulted, designation No.3 universal type, suitable for door shuttes of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and as directed.

S&F aluminium alloy wire cloth, 0.45mm dia of wire and average width of aperture 1.40mm and fixed with aluminium staples as fixed in repairs complete all as specified and as directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

S&F 4 mm thick plain asbestos cement board as in false ceiling with and applying two coats of oil bound distemper over a coat of chalk whitening and making to good existing frame without disturbing the other false ceiling complete all as directed by Engr-in-Charge. (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

S&F for PVC False ceiling consisting of 600 mm x 600 mm, 12 mm thick prelaminated self design PVC sheet of density 600 kg/Cum solid PVC panel including frame work made using aluminium T section of size (25mm x 25 mm, 19 gauge or 1mm thick) in square pattern of grid size of 600 x 600 mm. The aluminium frame work is supported from the ceiling with the help of GI wire/6 mm dia GI (upto 1200 mm length) adjusting and maintain for proper level to roof salbs by means of ceiling cleats made out of GE flat 40x3 mm sie 60mm long and expansion hold fasterners 12.5mm dia 40mm long complete etc. The aluminium frame work is supported on side wall with the use of aluminium 25 mm X 25 mm angles complete as per direction of Engr-in-charge, Manufacturer's specification & drawing.

S&F in repair 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification etc complete all as specified and as directed by Engineer-in-Charge.

S&F for Solid PVC Wall Lining consisting of 5mm thick plain / design colour PVC sheet inclusive of solvent and fixing at site on PVC frame as per specifications and drawing as per direction of Engr-in-Charge.

S&F false ceiling with Armstrong XL 24mm grid system of grid size 600x600mm with 12 mm thick ceiling board of RH-90. Grid shall be suspended from ceiling using 4mm dia pre straighten GI wire with 6mm nylon rawl plug & screws at 1200mm intervals complete all as manufacturers instructions and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 Grade St-240 complete all as specified and directed.

M&L prepration of steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of zinc chromate primer all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) etc complete all as specified and directed.

M & L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) etc complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 350x250x7 or 450x300x7mm thick as in skirting and dados, set and jointed in neat cement slurry and pointed in coloured cement to match and including 10mm thick backing coat in CM 1:6 etc complete all as specified and directed

Dismantling of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar complete all as specified and directed.

M&L glossy chequered cement concrete tiles 300x300x25mm thick, set jointed and pointed in near cement slurry in floors with white cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement mortor 1:6 all as specified and as directed by Engr-in-charge.

M&L PCC 1:4:8 type D2, using (40 mm graded agg) 75 mm thick as in sub base of flooring all as specified & directed

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm hickompacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; ® 13122C Providing and, complete all as specified and directed.

M&L PCC 1:2:4 type B1 using (20 mm graded aggregate) as in kerbing all around tile complete all as specified and directed.

S&F in repairs PVC tiles /sheets, of 2mm thick laminated plain coloured homogenous, laid with approved rubber based adhesive in floors all as specified and directed.

M&L PCC 1:2:4 type B2, using (40 mm graded agg) ,100 mm thick as in flooring/Hardstanding all as specified & directed

M & L PCC 1:3:6, type C2 (using 40 mm graded agg) 75 mm thick as in plinth protection without using extra cement complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc including removing debries directed for a distance max upto 500m complete all as specified.

M&L using ready Mix plaster for rendering 15 mm thick on fair faces of brick/concrete surfaces cement plaster in CM (1:4) , finished even and smooth without using extra cement, complete all as specfified and directed.

M & L using ready Mix plaster rendering 15mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 finished even and smooth (with out using extra cement) complete all as specified.

M&L rendering 5mm thick in CM 1:3 on ceiling finished even and smooth finish complete all as specified and directed.

M & L for exterior wall decorating and water proofing treatment to wall surface by wire brushing in order to remove dust, dirt, loose particles, laitance. Thereafter wash the surface with clean water & allow to dry.Cut the crack portion "V" shape and Fill visible cracks/jointis by Chemistic crackseal caulking compund & allow to dry for 24 Hours. Apply a primer coat of Chemistic Prime N Seal (water base primer) and allow to dry for 6 hours. Thereafter apply 02 coats of Chemistik PDS-50(WB high Build Anti Caronation Coating cum waterproffing) & shade by brush at the interval of 08 hours between the coat and allow to dry to match the existing shade. Rate quoted shall include for scaffolding to any height , covering etc, complete all as specified and directed by Engineer-in-charge

M & L for preparation of new or previously untreated plastered surfaces of walls and applying two coats of acrylic antifungal paint exterior grade paint plain or camouflage pattern on one coat of primer complete all as specified and as directed

M & L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening on plastered surfaces complete all as specified and directed.

M&L preparation of new plastered surface of ceiling and applying three coat of white wash on ceiling complete all as specified and directed.

S& F in repairs vitreous china urinal, half stall type complete including providing and fixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugs with and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, 32mm dia PVC waste pipe, inlet ,outlet etc complete all as specified and directed.

S&F fixed in repairs Wash hand basin vitreous china (flat back) size 550 x 400 mm including brackets waste brass chromium plated with long screwed shanks and fly nuts 32 mm size including 32mm dia PVC waste pipe complete all as specified and directed.

S&F in repairs 15 mm bore fancy type pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repairs vitreous china water closet (Squatting pan) “Orissa” pattern of size 580 x 440 mm white with integral foot rest and ‘P’ trap (excluding flushing cistern) but including PVC flush pipe and provision of lime concrete bedding complete all as specified and directed.

S&F vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) fixed as in repairs complete all as specified and directed.

S&F in repair for seat cover for pedestal pan with plastic water closet seat , black or white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repair for 10 litre capacity PVC valveless syphonic action type flushing cistern high or low level (exclusive of brackets) white with inlet ball valve, float and handle inlcuidng brackets complete all as specified and directed.

S&F in repairs fancy type bib taps chromium plated 15 mm dia cast copper alloy with crutch or butter fly handle screwed down for iron pipe or for brass ferrule , complete all as specified.

S&F in repairs fancy type chromium plated stop valves 15 mm bore cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repair 15 mm dia PVC connection of length 450mm long complete all as specified and directed.

Taking down eaves gutters and rainwater pipes( any size or pattern) , including all fittings, heads, shoes, bends , swan necks, etc, removal to store (measured overall as fixed along the centre line over fittings and accessories).

S & F plain galvanized mild steel sheeting 1 mm thick in ridge hips valley gutters drips and straight flashing welded or soldered joint complete all as specified

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified

S &F 150 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including bends complete all as specified and directed.

S &F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall. Complete all as specified and directed.

S &F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F for PVC (SWR) bends any radius 110mm bore complete all as specified and as directed

S&F for PVC (SWR) bends any radius 75mm bore complete all as specified and as directed

Demolition of pre-cast concrete block masonary built in cement mortar including all quoins, arches, pillars etc. and pre cast concrete articles complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks exc 10 cm in width in type B1 (1:2:4) and setting in mortar (1:6) complete all as specified and as directed

S&F stainless steel 304 grade framed work fancy/ornamental type in Gates/ stair hosing work and other similar works including all or any type of welding, holdfast, locking arrangement, followed by buffering and polishing for smooth finish complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old floor or concrete surfaces of any description & applying two coats of terra cotta exterior grade paint complete all as specified and directed.

M&L for attending complaints reletated to plumbing work, which includes water supply and obtaining completion from user this including minor repairs to taps, stop cock, mixer, health faucet, bottle trap, pillar tap, flushing cistern, replacement of washer, fitting to check nut, PVC Connetcion and aking w/s functional incase of blockage due to any reason re-fixing of GI Pipes joint if any leakage is found. Repair of unfunctional PVC cistern repair/ replacement, float valve, repair and replacemnt of PVC water tank etc by deploying required menpower for day to day aintenance to attend the complaint within time frame, tradmen shall have with minor spares such as check nut, jumper washer,, Nail, Screws, clips, Ladders, Ghori, Rehri etc.and necessary T&P complete all as specified and as directed by Engr-in-Charge. ( Note Main spares/ parts shall be measured and paid under seperate item here in after as supply only

Supply only 15 mm GI union ISI marked complete all as specified.

Supply only 20 mm GI union ISI marked complete all as specified.

Supply only 15 mm GI elbow ISI marked complete all as specified.

Supply only 20 mm GI elbow ISI marked complete all as specified.

Supply only 15 mm GI Tee elbow ISI marked complete all as specified.

Supply only 20 mm GI Tee elbow ISI marked complete all as specified.

Supply only 15 mm GI axe nipple 50 mm long ISI marked complete all as specified.

Supply only 20 mm GI axe nipple 50 mm long ISI marked complete all as specified.

Supply only 15 mm bore and 75mm long GI nipple ISI marked complete all as specified.

Supply only 20 mm bore and 75mm long GI nipple ISI marked complete all as specified.

Note (i) Item No 90 : If Contractor fail to attend the complaint on same day a recovery of Rs. 200/- per day per complaint shall be made from his dues. (date of issue of complaint slip and date of rectification of complaint will be the base of recovery) (ii) The contractor shall arrange the man power as and when required any numbers any time between 9.00 AM to 5.00 PM (iii) Items issued under complaint slips out of supply only items shall be recored in MB with reference to complaint slip docket No and old materials retrieved shall be issued to contractor under credit schedule.

M.K Enterprises

Mahadev Enterprises

M/s S.D Construction Co