GE/KHU-10/2020-21 SPECIAL REPAIR TO TOILET AND BLDG NO T-30 AT KHUMBATHANG UNDER GE KHUMBATHANG

Amount

M&L Roughening surfaces of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

Demolition of brick work or stone/boulder/block masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm and n. exc 4.0 Sqm each complete all as specified.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified.

Dismantling, wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets.

Dismantling timber in fillets, rails, posts, rafters, purlins etc under 40 Sq cm in section in any position unframed work complete.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc and n exc 10 sqm on plan and n exc 1.5m in depth and getting uot in hard/dense soil.

M&L Plain cement concrete type D-2 (1:4:8), 40 mm graded aggregate in foundations, filling and mass concrete all as specified and directed.

M&L for RCC 1:1:3 (20mm graded stone aggregates) as in beams cantilevers bressumer lintels over 1.5m span including necesssary form work complete as specified and directed.

M&L precast cement concrete type C-1, 1:3:6 using 20mm graded stone aggregates, block masonry with solid blocks, exc 10 cm width and setting in cement mortar 1:4 complete all as specified.

M&L for 15 mm thick rendering in two layer (10+5mm) in cement mortar 1:4 on fair surfaces of brick or concrete work and finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

Supply only integral water proofing compound complete all as specified.

M&L for Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces on walls and applying two coats of cement based paint complete all as specified.

M&L two coats of distemper Oil emulsion over a coat of primer on walls including preparation on new surfaces .

Returning, filling incl spreading leveling watering and well ramming in layers not exceeding 25mm in any type of soil.

Removing excavated material (soils) exceeding 250 m but n.exc. 500m and depositing where directed at a level not exceeding 1.5m above the starting point.

M&L Hard core of broken stones or boulders of gauge exc 63mm & n'exc 100mm, deposited, spread and levelled in layers n.exc 15cm thick incl watering and rolled to true surface.

Spreading and leveling excavated approved soil in layers not exceeding 25cm thick including watering and well ramming complete.

M&L 100mm thick cement concrete (1:4:8), type D2 using 40mm graded stone aggregate as sub base in floor complete all as specified.

M&L 25mm thick cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in sub floor, complete, all as specified.

M&L for screed or bedding layer 15 mm thick in cement mortar 1:6, finished even and fair on floors for laying floor finishes complete all as specified.

M&L for 10mm thick rendering/screeding on fair faces of brick / concrete surfaces in cement mortar 1:4 and finished even and fair for receiving tiles as in skirting/dado complete all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing and 20mm thick screed bed or bedding layer of cement mortar 1:6 complete. Note :- screed bed cost taken separately.

M&L Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors and skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L Glazed ceramic tiles in vertical surface 350x250mmx7mm/450X300X7to 8 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.complete, all as specified.

S&F natural colour anodized aluminium sliding window frame of size 65x40x1.60mm of approved manufacture fixed to floor, wall with rawl plug and screws and fixing shutter with frame or natural a colour anodized aluminium, handle tower bolt, hinges and glass pane not less than 5mm thick coloured fixed with rubber gasket and aluminium beading/glazing clip size 19.00x 17.30x0.70mm (weight 0.097 Kg/RM of both side) shutters with top, lock rail and vertical member of size 83.40x44.45x1.30 and bottom member of size 114.30x44.45x1.30mm of approved make as approved by Engr-in-Charge including aluminium grill, locks and handles etc.

M&L second class soft wood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints, etc. complete all as specified

S&F for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for preparing previously untreated wood and wood based materials of any description over 10cm width/ grith and applying two coats of Synthetic Enamel paint over one coat of pink primer including preparation of surface.

M&L for preparing previously untreated steel surfaces based materials of any description over 10cm width/ grith and applying two coats of Synthetic Enamel paint over one coat of red oxide primer including preparation of surface.

S&F 100 mm butt hinges medium weight cold rolled mild steel fixed with screws or welded all as directed.

S&F 75 mm butt hinges medium weight cold rolled mild steel fixed with screws or welded all as directed.

S&F 125 mm, long, Aluminium anodised, barrel tower bolt of extruded section and fixed.

S&F 125mm long , extruded aluminium alloy handles fabricated type anodised and fixed.

S&F Aluminium anodised sliding door bolt 250 mm long plate type stove enamelled black with bright bolt not less than 12 mm dia with and incl a minimum of 6 bolt and nut four on bolt plate and two on staple plate and fixed.

S&F hold fasts flats iron Fe-290 Gde-E-165 as specified

S&F Galvanised mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples or with wooden beads, screws and nuts botls etc. all as directed.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping ends and binding with and incl mild steel wire ( annealed ) not less than 0.90 mm dia or securing with clips .

Ditto but 5 mm dia and over upto and including 10 mm dia in stirrups .

Dismantling water tank any type of capacity exceeding 250 litres but not exceeding 500 ltrs .

S&F in Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 ltr

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for ironpipe and fixed. (Minimum weight 210 gms) complete screwed for iron pipe or brass ferrule of size 20 mm bore.

S&F Steel water tubing 15 mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) incliuding necessary taking down complete all as specified and directed.

S&F Steel water tubing 20 mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) including necessary taking down complete all as specified and directed.

S&F in repair Stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore and fixed in repairs, all as specified.

S&F in repair Stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20mm bore, all as specified.

S&F in repair 15mm stop valve, fancy chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions of bore dia 15mm all as specified.

S&F in repair PVC connection 15mm size with PTMT Nut of length 450mm complete.

S&F in repair vitreous china white wash basins, angle back type of size 580mmx440mm including brackets, cutting for and pinning the ends of brackets or erecting stands including 32mm bore dia waste coupling of PTMT ( Half or full threaded) ,(minimum weight 32 mm-45mm-60gms) with 32 mm High density polyethylene pipes (HDPE) of pressure rating 6kgf/cm² fixed complete to walls in floors complete all as specified.

S&F in repair Vitreous China urinals, Half stall type, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing with flush pipe, grating and Union for discharge pipe.

S&F 15mm Pillar taps, fany type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks fly-nuts, screwed for iron pipe and fixed

S&F in repair Bib taps, cast copper alloy, chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, all as specified.

S&F in repair 10 Litres PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolt, flushing cistern and flush pipe) complete all as specified.

S&F in repair cast iron trap 'P' or 'S' 100 mm all as specified and directed.

S&F in repair 100 mm dia Bends (any radius) diminishing pieces or tapers (larger bore measured).

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified.

S&F 75mm PVC (SWR) vent cowl

S&F in repair Stack clamps out of 50 x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm dia pipe.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of Fe 410-W (Gde-E- 250) quality-A and painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication, complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L 9mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work as in ceiling.

M&L 12mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative choice laminated and other side balancing white lamination fixed with screws to timber frame work on walls complete all as specified and directed..

M&L second class soft wood, plain fillets, square or rectangular in section of area exc 13 and n exc 25 Sqcm, clean sawn, secured with nails or brads.

M&L second class soft wood, plain fillets, square or rectangular in section of area exc 6 and n exc 13 Sqcm, clean sawn, secured with nails or brads.

M&L second class soft wood, bull nosed, splayed, chamfered or rounded on one edge or face n exc 3 Sqcm sectional area.

S&F in repair 19 mm dia teak wood finish curtain rod of good qaulity etc all as specified and directed.

S&F wooden brackets for wooden curtain rod of matching colour etc all as specified.

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface etc.

Fixing only one light point or one fan point controlled by one switch with cables 1.5 sq. mm size

Fixing only one 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size.

M&L for point wiring with 1.5 sqmm cable FRLS PVC insulated, unsheathed copper multistranded conductor, 1100 V grade of size 1.5 sqmm including necessary termination board 1.5 Sqmm PVC insulated unsheathed FRLS copper conductor as earthing and connected to common earthing with PVC heavy duty casing caping/PVC conduit ISI marked as rquired at site along with all accessories and making good the disturbed surfaces of wall/ ceiling etc for the following : - (a) One light point/ one fan point/ Bell Point controlled by one switch.

M&L in repair Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including 9W LED lamp.

Supply in repair switch piano flush type single pole one way 5 Amps all as specified

S & F in repair Ceiling rose 3 plates flush type 6 Amps,250 volts AC ISI marked

Supply and fixing in repair wall mounted E -lite LED pride plus fittings with LED tube 18 watts decorative ultra slim round profile LED light fixture with extruded polycarbonate envirmental freindly , energy efficient type 4 feet long including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose/PVC connector to light fittings Make: Havells/ Syska/Phillips/CG.

S&F in repair pressed sheet metal enclosure (MCB DB), single phase and neutral with 200 Amps rated bus bar, double door type, 240 volts complete for the following no. of way:- (a) 4 way

M&L in repair for Circuit breaker single pole, 5 to 40 Amp 240 volt B curve 10 KA, IP 20 complete all as specified and directed incl taking down old one Make : Legrand/L&T (Hager) /Schnider (Multi 9)

M&L in repair for Circuit breaker single pole & neutral 240 volt B curve 10 KA 40 Amps capacity IP 20 complete all as specified and directed incl taking down old one Make : Legrand/L&T (Hager) /Schnider (Multi 9)

M&L earthing complete with galvanized steel earth plate 60 cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less less than 1.5 mtr filled around with 15 cm thick alternate layers of charcoal dust and salt and connected to earth lead wire 4mm dia (8 SWG) by means of bolt, nut and check nuts and washers of galvanized iron or steel and thimble and other ends of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm bore and watering pipe 20mm dia light grade with funnel and wire mesh, pcc 1:3:6 type C-1 in chambers RCC 1:2:4 type B-1 in pit cover reinforced with 8 mm dia deformed bars 15cm center to center both ways all as directed by Engr-In-Charge, complete all as shown in electric plate No 3 of MES SSR Part I of 2010.

Dedcuct Credit for Demolished/Dismantled material Rs (-)24,210.00 (Minus) as listed in Schedule 'A' Part-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.

M/S kashmir fair deal services