Interior fit out works in the office space of Commission for Air Quality Management in NCR and Adjoining Areas (CAQM) at 17th floor,STC Building, Tols

S.NO. DESCRIPTION AMOUNT (RS)

1 ELECTRICAL 7,083,320.00

5 DATA CENTER 272,881.00

7 FIRE FIGHTING 747,642.00

8 FURNITURE 11,665,602.00

9 CIVIL & INTERIOR WORK 17,028,183.83

10 PLUMBING 1,760,983.73

Total Amount 48,639,129

Total Amount 48,639,129

Digitally signed by ASHWANI

ASHWANI KUMAR BANSWAL

S.H. 1 ELECTRICAL WORK: AQM , NEW DELHI

ABSTRACT OF COST-ELECTRICAL WORKS

ELECTRICAL WORK

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

A. INTERNAL WIRING

1 1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

pvc conduit medium with modular switch, modular plate, suitable G.I box and

earthing the point with 1.5 sqmm. FRLS PVC insulated copper conductor single

core cable etc as required.

2 1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan point/

call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/ recessed steel

conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc. as required.

3 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

FRLS PVC insulated copper conductor, single core cable in surface/ recessed

pvc conduit medium as required

c 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 325.00 263.00 85,475.00

d 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 100.00 356.00 35,600.00

f 1.7.9 4 x 6 sq.mm + 2 x 6 sq.mm. earth wire Metre 100.00 529.00 52,900.00

g 1.7.10 4 x 10 sq.mm + 2 x 10 sq.mm. earth wire Metre 50.00 670.00 33,500.00

h 1.7.11 4 x 16 sq.mm + 2 x 16 sq.mm. earth wire Metre 50.00 946.00 47,300.00

4 1.24 Supplying and fixing following modular switch/ socket on the existing modular

plate & switch box including connections but excluding modular plate etc. as

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

5 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base &

cover plate for modular switches in recess etc. as required.

6 1.31 Supplying and fixing suitable size G.I box with modular plate and cover in front Each 120.00 401.00 48,120.00

on surface or in recess, including providing and fixing one 3 pin 5/6 amps

modular socket outlet and one 5/6 amps modular switch, connection etc. as

required. (For light plugs to be used in General purpose).

7 1.32 Supplying and fixing suitable size G.I box with modular plate and cover in front Each 10.00 495.00 4,950.00

on surface or in recess, including providing and fixing one 6 pin 5/6 & 15/16

amps modular socket outlet and one 15/16 amps modular switch, connection

etc. as required. (For power plugs to be used in General purpose).

8 2.18 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole Each 5.00 1,146.00 5,730.00

and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet

steel enclosure, on surface or in recess, with chained metal cover for the socket

out let and complete with connections, testing and commissioning etc. as

9 MR Supply and fixing of 32 Amps industrial socket points as directed including Nos. 3.00 6,387.00 19,161.00

providing 32 A socket angled outlet and 32 amps interlocking socket with 32

amps "D" curve DP MCB 5 sided PSP thermoplastic for housing and L6-30 type

connector socket and MCB and earthing complete with connections, testing

and commissioning etc. as required.

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

10 MR Fabricating supplying installation on surface/cable tray 2.0 mm thick factory

fabricated GI Sheet raceways height 40 mm and of totally enclosed with 3mm

thick covered with screw. Two lengths of channel / channel and junction box

shall be joined together to make it dust and water proof. Chipping and

removing screed to install the raceways in floor, including removal and

disposing of debris as per PMC instructions, finishing with PCC, providing

chicken mesh and making good as per Engineer in charge

11 4.5 Supplying and installing following size of perforated painted with powder

coating M.S. cable trays Reducer with perforation not more than 17.5%, joined

with connectors, suspended from the ceiling with M.S. suspenders including

bolts & nuts, painting suspenders etc as required.

a 4.5.10 450 mm width X 62.5 mm depth X 2.0 mm thickness RM 5.00 2,291.00 11,455.00

b 4.5.4 300 mm width X 50 mm depth X 1.6 mm thickness RM 10.00 1,505.00 15,050.00

c 4.5.2 150 mm width X 50 mm depth X 1.6 mm thickness RM 30.00 1,023.00 30,690.00

12 MR Fabrication. Supplying, installation, fixing in position GI Junction Boxes 2 mm

thick complete with 3 mm thick GI Covers with screw duly providing rubber

gaskets between the cover and the Junction Box, screws etc. as required

a 500 x 500 x 50 mm MS junction box. Nos. 2.00 1,250.00 2,500.00

b 350 x 350 x 50 mm MS junction box. Nos. 5.00 970.00 4,850.00

c 300 x 300 x 50 mm MS junction box. Nos. 15.00 835.00 12,525.00

d 200 x 200 x 50 mm MS junction box. Nos. 15.00 778.00 11,670.00

e 150 x 150 x 50 mm MS junction box. Nos. 15.00 658.00 9,870.00

f 100 x 100 x 50 mm MS junction box. Nos. 10.00 538.00 5,380.00

13 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor,

single core cable in the existing surface/ recessed steel/ PVC conduit as

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

14 MR Providing and fixing on work station/ partition of 3 Nos.6/13 amp flush type 3 Nos. 110.00 658.00 72,380.00

pin international socket and 1 No. 16 amps switch, cover plate in existing flap

box/ raceways/GI box for for housing switches and sockets and earthing

complete as required ( for ups power point)

15 MR Providing and fixing on work station/ partition of 2 Nos.6/13 amp flush type 3 pin Nos. 30.00 598.00 17,940.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( For ups power points.)

16 MR Providing and fixing on work station/ partition of 1 No.6/13 amp flush type 3 pin Nos. 5.00 518.00 2,590.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( for ups power points.)

17 MR Providing and fixing on work station/ partition of 2 Nos.6/13 amp flush type 3 pin Nos. 10.00 598.00 5,980.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( For raw power points.)

18 MR Providing and fixing on work station/ partition of 1 No.6/13 amp flush type 3 pin Nos. 110.00 518.00 56,980.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( for raw power points.)

19 1.21 Supplying and fixing of following sizes of pvc conduit medium along with

accessories in surface/recess including cutting the wall and making good the

same in case of recessed conduit as required.

a 1.21.1 20mm dia conduit Metre 190.00 84.00 15,960.00

b 1.21.2 25mm dia conduit Metre 220.00 90.00 19,800.00

c 1.21.3 32mm dia conduit Metre 65.00 92.00 5,980.00

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

20 ` Providing and fixing in position the following pvc flexible conduits including all

fixing accessories as required.

a 20 mm dia flexible conduit with end couplers RM 25.00 35.00 875.00

b 25 mm dia flexible conduit with end couplers RM 45.00 45.00 2,025.00

c 32 mm dia flexible conduit with end couplers RM 10.00 65.00 650.00

21 MR Supply, installation, testing and commissioning of the following sizes of PVC

trunking system with end caps, bends, elbows complete as required.

1 MR Providing and fixing of Gel-Chemical Earthing Electrode of G.I. made as pipe in Each 4.00 60,879.00 243,516.00

pipe technology(IS:3043 : 1987)duly CPRI Approved as per following

Length - (3000 mm)

DIA (outer) - (80 mm)

DIA (Inner) - (40 mm)

DIA-Terminal Strip Hole - (25 mm)

Space Inside Electrodes - (Filled with Conductive Mixture)

Hot Dip Galvanizing - (70 - 100 Microns)

And earth enhancing compound should be used to treat the soil for lowering

the effective ground impedance 50Kg for each earth pit to make it

maintenance free and to minimize the ground voltage potential rise and pit

covered with PVC Cover.

2 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including Each 4.00 6,216.00 24,864.00

accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke

and salt as required.

3 5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from Metre 100.00 1,224.00 122,400.00

earth electrode including connection with brass nut bolt, spring, washer

excavation and re-filling etc. as required.

4 5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth Metre 100.00 483.00 48,300.00

electrode including connection with G.I. nut, bolt, spring, washer excavation

and re-filling etc. as required.

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

5 5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess with all Metre 150.00 1,009.00 151,350.00

accessories for connections etc. as required.

6 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess with all Metre 200.00 206.00 41,200.00

accessories for connections etc. as required.

7 MR Supplying ,laying, and making proper connections, end terminations, testing & 0.00

commissioning of the following sizes of 1.1 KV unarmoured PVC insulated

copper conducter cables heavy duty flexible cable (wires) in existing RCC

ducts/ laid in ground /laid on Cable Trays including clamping the cables to

supports in an approved manner as required complete with all accessories.

a 1 x 50 sq. mm PVC insulated copper conductor flexible cable (Green colour RM 125.00 774.00 96,750.00

for UPS Earthing)

b 1 x 25 sq. mm PVC insulated copper conductor flexible cable (wire) (Green RM 25.00 409.00 10,225.00

colour for UPS SDB Earthing)

c 1 x 16 Sq. mm PVC insulated copper conductor wire (Green Colour for UPS DB RM 25.00 336.00 8,400.00

Sub-main Earthing)

d 1 x 10 Sq. mm PVC insulated copper conductor wire (Green Colour for UPS HUB RM 100.00 203.00 20,300.00

DB Sub-main Earthing)

e 1 Nos x 6 Sq. mm PVC insulated copper conductor wire.(Green Colour for false RM 100.00 93.00 9,300.00

flooring earthing)

f 1 x 4 Sq. mm PVC insulated copper conductor wire (Green Colour) for server RM 100.00 64.00 6,400.00

8 MR Supply, installation, testing and commissioning of copper Earth Set 4.00 5,286.00 21,144.00

busbar(50X5X400)mm in MS sheet enclosure complete as required.

C SUPPLY & FIXING OF LIGHTING FIXTURES

1 Supply, installation, testing and commissioning of the the following Lighting

fixtures including all internal connection wires, electronic ballast, lamps,

mounting arrangement, suspensions and all necessary items required to install

the light fixtures at site. Rate shall include all taxes and duties, transportation

a MR 1x12 Watt Circular Down LED Light Fixture suitable for grid tile ceiling 600x600 Nos 4.00 1,600.00 6,400.00

grid with electronic ballast, mounts to support the ballast or with integral ballast,

suitable lengths of prewired connection between ballast and light fixture,

diffuser, suitable mounts, suspension cables complete as required.

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

b MR LED cove light fixture with average lumen output of 630 lm per metre for white RM 185.00 850.00 157,250.00

color including all drivers, connecting cables, controllers, led mounted in

extruded poly corbonate, suitable to end to end coupling, non dimmable,

average 4 watt / metre for mono color and 11 watt/ metre for white color.

Color as per PMC instruction complete as required.

c MR Recessed mounted 36W LED light fixture suitable for mounting in 300x1200 grid Nos. 65.00 8,240.00 535,600.00

ceiling with acrylic duffuser with 100% uniform illumination, intergral driver,

internal wiring, supports, accessories for mounting, lamps complete.

d MR COV LED disk round 9 w light ceiling fitting complete with all required No. 205.00 850.00 174,250.00

accessories including connection and lamp .

e MR Recess mounting Linear LED luminarie with energy efficient high efficency No's 30.00 6,920.00 207,600.00

translucence PMMA diffuser, LED electronic driver and other accessories pre

wired up to terminal block, 1200 mm (NS) long with CRCA sheet housing, 31 -36

watt, Luminous efficiency of luminair >80 lm /w. CCT 6000 (+/_500) K , Color

Rendering Index (CRI) > 80 , service life 50,000 hrs at 25 deg,C.

f MR Supply, Installation, testing and Commisioning of decorative chandlier light No's 1.00 47,764.00 47,764.00

fixture, consisting of LED lights, drivers, etc. inclusing all accessories, supports

from true RCC Slab complete with all respects. (Base Rate Rs.35000/-)

g MR Supply, Installation, Testing & Commissioning of LED ring pendant shape indoor Nos 6.00 17,912.00 107,472.00

surface office panel suitable for general lighting. Luminaire should have CRCA

body in white color . The luminaire should have CRI > 80 and CCT of 4000K. The

luminaire shall be compliant with IP20 classification.The fixture should have a

minimum system efficacy of 80 lumen/Watt and a minimum system lumen

output of 3300 lumens and maximum system wattage 43Watts. The luminaire

shall be designed so as to ensure lumen depreciation of up to 30% over 50k

burning hours @ design ambient temp 45 deg C. The electronic driver used shall

have a power factor >0.90 . Similar to image shown below with all necessary ms

conduit , wiring switch socket to control light fixture complete.Size 1200mm Dia.

D OCCUPANCY SENSORS

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

1 MR Supply, fixing testing and commissioning of occupancy sensors with day light Nos. 18.00 4,250.00 76,500.00

sensor with all necessary wiring to be integrated for lighting control complete

with following specification.

PIR Motion Sensors will itself recover its cost by reducing your electricity bills and

will further save your electricity cost for the future. Very easy installation and can

be installed by technician itself. No separate wiring is required hence no

additional installation cost. No modification is required and complies with

current aesthetics. Pay back within ten months according toresidential meter

and six months according to construction meter. Ingress Protection: IP20 as

required as per clients requirement.

E Automation Dali Light

1 MR Recess mounting Linear With Dali dimmable driver LED luminarie with energy No's 18.00 10,843.00 195,174.00

efficient high efficency translucence PMMA diffuser, LED electronic driver and

other accessories pre wired up to terminal block, 1200 mm (NS) long with

CRCA sheet housing, 31 -36 watt, Luminous efficiency of luminair >80 lm /w.

CCT 6000 (+/_500) K , Color Rendering Index (CRI) > 80 , service life 50,000 hrs at

2 MR Supply, Installtion, Testing & Commissioning of Recess Mounted circular 15W LED Nos. 25.00 7,328.00 183,200.00

downlighter with pressure diecast aluminimum housing, high efficiency PMMA

diffuser complete with electronic LED driver, PF>0.9, THD<10%, rated life of L-70

@ 30,000 hours having minimum lumens output of 2100 lumens and efficacy

better than 80 lumens / watt with CRI> 80 including fixing in false ceiling &

connection with 3x1.5 Sq.mm. PVC insulated FRLS copper conductor cable in

flexible metalic conduit etc. as required. With Dali dimmable driver.

3 MR Supply, Installation Testing & Commissioning of DIN - rail mounted Dali dimming No's 4.00 83,315.00 333,260.00

controller with two (2) independent Dali buses with upto 64 ballasts per bus, 4

groups of sensor input, i/c power supply at 220-240V, 50 Hz. i/c connections etc

4 MR Supply, Installation Testing & Commissioning of DIN - rail mounted ON/OFF No's 2.00 54,727.00 109,454.00

switching controller with 4 switched outputs having max load limit of 10 Amp

per output, includes communication link to any device and 2 group of sensor

inputs, i/c power supply at 230V, 50Hz.i/c connections etc as reqd.

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

5 MR Supply, Installation Testing & Commissioning of 8 button wired keypad with No's 2.00 41,542.00 83,084.00

infrared receiver complete with mounting back box 75mm (W) X 75mm (H) X

35mm (D), engraving codes with front plate in arctic white finish, 8 scene

wireless remote control including batteries complete as required.

1 MR Supply, laying and testing of under noted sizes of Aluminium conductor XLPE

insulated PVC sheathed & sleeved FRLS armoured and overall PVC sleeved 1.1

KV grade power distribution cables conforming to relevant IS code 7098 and as

per specification in ground or in existing trenches/ through pipe/ on wall / on

cable trays including dressing and clamping the cable with MS clamps etc. as

2 9.1 Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

3 MR Supply fixing and making proper end termination with sutable accessories of

under noted sizes of copper conductor PVC insulated PVC sleeved 1.1 KV

grade power distribution flexible cable/wires heavy duty conforming to

relevant IS code and as per specification in ground or in existing trenches/

through pipe/ on wall / on cable trays including dressing and clamping the

cable as required.

a 1 x 50 sq.mm PVC insulated flexible copper conductor cables RM 65.00 780.00 50,700.00

b 1 x 25 sq.mm PVC insulated flexible copper conductor cables RM 85.00 460.00 39,100.00

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

c 1 x 16 sq.mm PVC insulated flexible copper conductor cables RM 125.00 380.00 47,500.00

d 1 x 10 sq.mm PVC insulated flexible copper conductor cables RM 125.00 298.00 37,250.00

e 1 x 6 sq.mm PVC insulated flexible copper conductor cables RM 305.00 260.00 79,300.00

f 1 x 4 sq.mm PVC insulated flexible copper conductor cables RM 310.00 140.00 43,400.00

4 MR Supply and fixing of ms angle/chanel support or frame work in position Kg. 250.00 140.00 35,000.00

including clamps,with fabrication work including cutting, bending, welding,

drilling bolting etc. as per design as required. One coat of primer and 2 coats

of enamel paint of approved shade shall be provided.

5 MR Supplying and fixing of following size of perforated G I cable trays with

perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with G I. suspenders including bolts &

nuts, etc as required.

a 450 mm width X 50 mm depth X 2.0 mm thickness RM 85.00 1,470.00 124,950.00

b 300 mm width X 50 mm depth X 1.6 mm thickness RM 180.00 1,150.00 207,000.00

c 150 mm width X 50 mm depth X 1.6 mm thickness RM 120.00 790.00 94,800.00

G L.T PANELS/ DISTRIBUTION BOARDS

MR Supply, installation, testing and commissioning of indoor floor mounted/ wall

mounted, IP42, factory built, modular, sectionalised, compartmentalized,

extendable type LT cubicle panel of suitable size suitable for operation on

433/415 volts, 50 Hz AC 3 phase 4 wire supply system fabricated from CRCA

sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates

with stiffeners wherever required, having vibration free structure chemically

treated with seven tank process or better before painting for surface treatment

and powder coated in approved shade, with suitable electrolytic grade high

conductivity bus bars extensible, DMC/ SMC (whichever is superior) bus bar

supports, with short circuit withstand capacity as mentioned ,bottom base

channel of section not less than 100mmX 50mmX 5 mm thick, fabrication shall

be done in transportable sections, entire panel shall have a common earth bar

of required size at the rear with 2 Nos. earth stud, connections and

interconnection with solid conductor wires / copper strips, neutral links, control

wiring with 1.5 sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C

cable for voltage & current respectively, including providing and fixing

following switch gears and as per schedules ,technical specifications

etc.complete as required.

1 Electrical Panel-1 Nos 1.00 259,292.00 259,292.00

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

Surge arrester (1 No.)

2kVp,50kA rated surge arrestor suitable fo both lightning and switching

surges,complete with suitable protection fuse (inbuilt).

415V, 50Hz, 160A, 4P, 25kA for 1 sec rated thermal magnetic based MCCB with

inbuilt LSIG protection - 1 Nos.

Metering (1 No.)

Multifunction meter with inbuilt selector switch for measurement of current,

voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line and

phase) complete as per specifications

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 1

LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on, off,

415V ,160/5A, 10VA, CL-1 current transformer for metering

Busbar (1 Set - 4P + E)

Busbar made up of electrolytic grade high conductivity aluminium in

rectangular cross section and suitable for 415V, FP, 50 Hz, 200 A, 25 kA for 1 sec

of required length and cross sectional area.

2 Nos. 415V, 50Hz, 100A, 4P, 25kA for 1 sec rated Thermal magnetic based

7 Nos. 415V, 50Hz, 40A, 4P, 10 kA MCB.

4 Nos. 415V, 50Hz, 63A, 4P, 10 kA MCB.

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 2

2 UPS Output Panel

415V, 50Hz, 160A, 4P, 25kA for 1 sec rated thermal magnetic based MCCB with

inbuilt LSIG protection - 2 Nos.

Metering (2 No.)

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

Multifunction meter with inbuilt selector switch for measurement of current,

voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line and

phase) complete as per specifications

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 2

LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on, off,

2 Nos.-415V ,160/5A, 10VA, CL-1 current transformer for metering

Busbar (1 Set - 4P + E)

Busbar made up of electrolytic grade high conductivity aluminium in

rectangular cross section and suitable for 415V, FP, 50 Hz,300 A, 25 kA for 1 sec

of required length and cross sectional area.

2 Nos. 415V, 50Hz, 40A, 4P, 10 kA MCB.

3 Nos. 415V, 50Hz, 63A, 4P, 10 kA MCB.

3 Light & Power Distribution Board

a MR Supply and installation of sheet metal enclosed double door 48modules TPN DB, Nos. 2.00 21,378.00 42,756.00

each phase consisting of 8 Nos. 10/20 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A TPN MCB as incomer. all mcb's shall be

b MR Supply and installation of sheet metal enclosed double door 56modules TPN DB, Nos. 2.00 23,133.00 46,266.00

each phase consisting of 10 Nos. 10/20 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A TPN MCB as incomer. all mcb's shall be

4 UPS Distribution Boards

S.NO DSR 2018 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

a MR Supply and installation of sheet metal enclosed double door 56modules TPN DB, Nos. 2.00 23,133.00 46,266.00

each phase consisting of 12 Nos. 10/20 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A TPN MCB as incomer. all mcb's shall be

b MR Supply and installation of sheet metal enclosed double door 48modules TPN Nos. 2.00 21,378.00 42,756.00

DB,, each phase consisting of 10 Nos. 32/16 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A 4P MCB as incomer. (For UPS Power)

all mcb's shall be D-curve.

H MR Supply, installation of 1.1KV grade rubber mat 900mm wide in electrical rooms. RM 6.00 2,394.00 14,364.00

I MR Supply & Fixing of danger notice board Nos. 2.00 1,796.00 3,592.00

J MR Supply of First aid box Nos. 1.00 599.00 599.00

K MR Supply & Fixing shock treatment chart Nos. 2.00 1,796.00 3,592.00

TOTAL ELECTRICAL WORK AMOUNT 7,083,320.00

S.H. 2 UPS WORK : AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

SITC of 30 kva ups (1 working + 1standby) expandable to 60 kva modular

having hot swapable modue 20 kva each ups true online double conversion

VFI technology, Modular construction, High Frequency PWM using IGBT

technology, Parallel redundant, 3 phase AC Input & 3phase AC Output UPS.

Input range should be 360 VAC-450 VAC, Dual input (separate input for

rectifier and separate input for bypass). Provisions for maintenance by pass

switch module. Microprocessor based LCD display & indication for various

electrical parameters. LED indication with alarm for major fault. Provisions for

remote monitring indication with potential free contact. The system shall be

complete with Parallel Redundant Kit and it will work as parallel redundent

(2nos modules. 1 nos.working + 1no.module standby)

Supply, Installation, Testing and Commissioning of 12V Monoblock suitable size

and nos of sealed maintenance free batteries supporting for 30KVA UPS

System for providing 15 minutes back up time with each UPS at full load with

interconnecting leads, mounting racks/stands for stacking the batteries, along

with Battery Circuit Breaker, Connection, Interconnections, and standard

accessories etc. Complete as reqd.

a UPS Capacity - 1x 30 KVA with 15 mint. Battery backup each ups No. 1 600327.00 600,327.00

2 STATIC SWITCH MODULE FOR FLOOR DB

SITC of static switch module with microprocessor based control and suitable

for liner and non linear load at particulars distribution board of critical load in

event of short circuit overload or any other fatal condition with built-in

Technical Protections like short circuit, Overload, High/Low Voltage cutoff

protection of load from source inclusive of Bypass facility Static Bypass Module

is activated during malfunctioning conditions of load like :-

• Short Circuit

• Bypassing of particular load if required

• Resulting in non tripping of main UPS unit

• Input Voltage (320-460VAC) 3 phase

• Input frequency 50Hz

Indication & Monitoring

• UPS Supply on/source I

• Load on UPS supply/source I

• Main supply on/source II

• Load on mains supply/Bypass

• Bypass Switch on

• Bypass Switch off

a Capacity: 63A 3 Phase Nos 1 103741.00 103,741.00

TOTAL UPS WORK AMOUNT 704,068.00

S.H. 3 FIRE DETECTION & ALARM SYSTEM WORK : AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

1 FIRE DETECTION & ALARM SYSTEM

1.1 Dismantling of existing fire alarm detectors complete as required 10 Nos 473.00 4730.00

1.2 Dismantling of existing fire alarm cable complete as required 25 Mtrs 25 625.00

1.3 Resinstallation and reconfiguration of existing fire alarm detectors as per site 10 Nos 700 7000.00

requirement complete as required

1.4 Laying of existing fire alarm cable as per site requirement complete as required 100 Mtrs 43 4300.00

1.5 Supply, Installation, Testing, and commissioning of smoke detectors compatible 75 Nos 3500 262500.00

with fire alarm system and as per site requirement complete as required

1.6 Supply, Installation, Testing, and commissioning of fault isolators compatible with 5 Nos 3900 19500.00

fire alarm system and as per site requirement complete as required complete

1.7 Supply, Installation, Testing, and commissioning of control/monitor module 1 Nos 3900 3900.00

compatible with existing fire alarm system and as per site requirement

complete as required complete as required

1.8 Supplying, installation, testing and commissioning of micro processor based

intelligent addressable main fire alarm panel, central processing unit with the

following loop modules and capable of supporting not less than 240 devices

(including detectors) and minimum 120 detectors per loop and loop length up

to 2 km, network communication card, minimum 320 character graphics/ LCD

display with touch screen or other keypad and minimum 4000 events history log

in the non volatile memory (EPROM), power supply unit (230± 5% V, 50 hz), 48 hrs

back-up with 24 volt sealed maintenance free batteries with automatic

charger. The panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice evacuation

system (which is part of the schedule of work under SH: PA System) and shall be

complete with all accessories . The panel shall be compatible for IBMS system

with open protocol BACnet/ Modbus over IP complete as per specifications.

Note : Cost to inclusive of integration of fire alarm system with existing building

fire larm system.

2.1 Dismantling of existing speakers complete as required 5 Nos 100 500.00

2.2 Dismantling of existing complete speaker cable as required 25 Mtrs 25 625.00

2.3 Resinstallation and reconfiguration of existing speakers as per site requirement 5 Nos 200 1000.00

complete as required

2.4 Laying of speaker cable as per site requirement complete as required 325 Mtrs 34 11050.00

2.5 Supply, Installation, Testing, and commissioning of 6watt ceiling speaker as per 50 Nos 1500 75000.00

site requirement complete as required

2.6 Supply, Installation, Testing, and commissioning of 10 watt wall mount speaker 2 Nos 3900 7800.00

as per site requirement complete as required

2.7 Supply, Installation, Testing, and commissioning of 500watt amplifier as per site 1 Nos 125000.00 125000.00

requirement complete as required complete as required

TOTAL FIRE DETECTION & ALARM WORK AMOUNT 762,352.00

S.H. 4 : LAN WORK AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

1 PASSIVE LAN SYSTEM

1.1 Supply, Installation, Testing & Commissioning of 24 Port loaded Jack Panel CAT 8 Nos 12500 100000.00

6A, Staggered 24 Port panel in 1U Rack Unit, Copper Alloyed Contact

Material, EIA 568A/B wired, PC + glass fiber, UL 94V-0, black color, Front Port

Labelling, 22-24 AWG Wire Accumulation complete as required

1.2 Supply, Installation, Testing & Commissioning of quad face plate having 125 Nos 300 37500.00

provision for four I/O along with spring type shutter for dust proof, made of ABS

PVC plastic complete as required

1.3 Supply, Installation, Testing & Commissioning of dual face plate having 10 Nos 280 2800.00

provision for one I/O along with spring type shutter for dust proof, made of ABS

PVC plastic complete as required

1.4 Supply, Installation, Testing & Commissioning of CAT 6A Information 160 Nos 450 72000.00

Outlet,Universal label permits T568A or B wiring, UL® Listed, meets all TIA and

ISO requirements.Complete in all respect as required by the site.

1.5 Supplying and drawing of LSZH UTP 4 pair CAT 6A LAN low smoke Cable in the 1800 Mtrs 85 153000.00

existing surface/ recessed Steel/ PVC conduit as required.

1.6 Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord LSZH 2 Mtr, 120 Nos 445 53400.00

4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim

clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed,

meets all TIA and ISO requirements. Complete in all respect as required by site

1.7 Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord LSZH 1 Mtr, 250 Nos 425 106250.00

4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim

clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed,

meets all TIA and ISO requirements. Complete in all respect as required by site

1.8 Supply, Installation, Testing and Commissioning of 42 U Networking Rack 1 Nos 75000 75000.00

(600*800), Front Glass Door Unit and Grilled back door unit, lockable Door unit,

Load Rating of Min 450 Kg. Pillar of frame must be aluminum and Rest plated

are steel, Powder Coated Rack with Castors (4nos.), Fan (4 Nos.), Cable

Manager (2Nos), Full Tray Unit (1 Nos.), PDU (1Nos.) complete in all respect as

1.9 Supply, Installation, Testing & Commissioning of 6 Core Armoured Multi Mode 85 Mtrs 190 16150.00

Fiber optic cable, Central Lose Tube With Jelly Compound, Corrugated steel

tape armoured, Heaving 1300 nm Wavelength in the existing surface/ recessed

Steel/ PVC conduit as required.

1.10 Supply, Installation, Testing and Commissioning of Multi Mode fiber SC-LC 1 Nos 2200 2200.00

Duplex patch cord of 2 Mtrs. for Gigabit Connection between Patch Panel

and Switch complete as required.

1.11 Supplying, Installation, Testing and Commissioning of fiber optic SFP + fiber 1 Nos 9500 9500.00

patch cord of 3 meter length having SFP+ modules at both ends complete as

1.12 Supply, Installation, Testing & Commissioning of Fiber optic Mini GBIC SFP Trans 1 Nos 14500 14500.00

receiver 10G for network switch with Built-in spring latch for easy module

removal, Hot Swappable, Comply IFC and FDA Safety Standards complete as

1.13 Supply, Installation, termination & testing of 2 mtr length SC pigtails 9/125 5 Nos 950 4750.00

micron for Multi Mode Pigtails complete as required.

1.14 Supply, Installation, Testing & Commissioning of 12 Port Unloaded Line 1 Nos 18500.00 18500.00

Interface Unit LIU, 19",1u Rack Mountable unit with splice Tray Holder, Cable

Guide, Fiber Management and Splicing of Pigtails and Fiber Cables Including

Joints and Connectors complete as required.

TOTAL LAN WORK AMOUNT 665,550.00

S.H. 5 DATA CENTER WORK : AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ RATE AMOUNT

1 Rodent Repellent System

SITC of Rodent Repellent System by using electronic transmitters of high

frequency sound waves, which will emit sound at very high decibel levels painful

to pests, as described in the specification given hereunder. The system shall

consist of a master console, satellites and its cable circuits These will be electronic

transmitters of high frequency sound waves (well above the 20KHZ frequency

which is the upper limit of the hearing range of the human ear.) emitting sound at

high decibel levels (sound pressure) that is audible and painful to pests, but

inaudible and harmless to humans. The system will consist of one Master Console

and twelve Sateliites / Transducers. The console will be installed in the control

room, or as directed and the satellites in the problem areas as required. The

powerful sound waves generated by the satellites shall be within the hearing

range of many pests ansd cause them pain and discomfort. Satellites should be

quiet and inaudible to humans

These will be electronic transmitters of high frequency sound waves (well above

the 20KHZ frequency which is the upper limit of the hearing range of the human

ear.) emitting sound at high decibel levels (sound pressure) that is audible and

painful to pests, but inaudible and harmless to humans. The system will consist of

one Master Console and twelve Sateliites / Transducers. The console will be

installed in the control room, or as directed and the satellites in the problem areas

as required. The powerful sound waves generated by the satellites shall be within

the hearing range of many pests ansd cause them pain and discomfort. Satellites

should be quiet and inaudible to humans

Each Satellite will cover an open floor area of approximately 400 sq.ft. for an

average height of the ciling is 10 ft. As regards area of suspended ceilings or

raised floorings, it should cover an approximate area of 400 sq.ft. The satellites

1. Be able to mount in any angle to match the decor.

2. Possible to install in sensitive areas

3. Should withstand high temperature in suspended ceilings and low temperature

in cold storages and air locks

4. Should not require a power connection.

5. Should be able to test on an audible range with the help of a self-testing

facility or any other suitable means

Crystal: DM 44t 24V MAS Germany

Frequency: Peak frequency responses of the satellites are

i) 21.6 KHz + /- 3KHZ

ii) 31.6 KHz + /- 3KHz

iii) 50.4 KHz + /- 3 KHz

iv) 60 KHz + /- 3KHz

Nature of sound waves: The sound waves propagated should be linear sine

waves with constantly varying frequencies.

Operating environment: Range of -4 deg C to 60 deg C, 100 % humid

environment and under water.

Circuit: Signal generator should have full wave rectification, regulated 12V DC

power supply to withstand power fluctuations ranging from 170V AC to 270V AC .

Amplifier should have a preamplifier stage coupled with signal generator for dual

transistor amplification having a push-pull configuartion

Uniform pressure output of 80 db to 110 db with 360 deg transmission angle. Linear

propagation of mixed / variable frequencies detectable at, or about 40 ft.

distance from the source (Transducer/Satellite). Spatial average intensity-83mW

Encluding following accessories as required.

5A Power Socket (230 V AC) will be provided for each VHFo as may be required.

Operating frequency: Above 20 KHz (Variable), Sound output: 80 db to 110db at

1.00 mts., Powre output: 800MW per satellite., Power Consumption: 15 Watt

Approx., Power Supply: 230 V AC, 50 Hz, Mounting: Wall / Table, Dimension: 16" x

8" x 4", Weight: 5.5 Kgs approximately

Master Console of Rodent Repellent satellites/transducers

controller for all areas (Main DC + UPS) with communication port with BMS

Satellites/Transducers for all areas and voids

2 core 1.5 sq.mm Cu. Armored FRLS Cable

Make - C-System / Maser / Star Electronics

1.a. Complete Rodent Repellent System Job 1 133786.00 133,786

2 Water Leakage Detection System

SITC of Addresble Water leak detection sensing tape shall be installed in the

Server room. Events are clearly reported on LCD/LED display with full English

language description of the nature of the fault in the panel. Provision shall be

inbuilt for integrating with the Ibms system. Components of water leak detection

system The Water leak detection system shall comprise of Tape Sensors, Water

Leak detection modules, Condensation detectors, I/O modules and sounders all

connected to a Control Panel. Control Panel The control panel shall be

Computerized 2 zone multiplex controller with a facility to add on dialer and

speech processor. The system shall be programmed, armed or disarmed through

a control keypad. The control key pad shall have a 16 character LCD display for

viewing various events.

The code to arm or disarm the system shall be changed only by entering a

master code. The system shall have 2 zones and all the detectors shall be

connected through a 2 core cable. The entire system shall be backed up by a

maintenance free rechargeable battery to take care of system's power

requirements whenever power fails. The system shall be totally tamper proof and

shall activate an alarm if the control panel is opened, the sensors tampered with

or if the system cables are cut even in the disarmed state. The system shall log 500

events. The Detectors, I/O Modules, Remote Keypads and other Devices shall be

connected to a system on a single 2 Core Cable Bus to avoid individual cabling

of zones. The system shall have a Buffer memory of minimum 250 events and log

each event with exact date and time. The controller shall have a Serial Port for

connecting to a computer.

The system shall be totally tamperproof and shall activate an alarm if the control

panel is opened, the sensors tampered with or if the system cables are cut even

in the disarmed state. Tape Sensors UL listed Tape sensors are to be used to

detect water leaks under floors and the Tape sensors shall be covered with

plastic netting to prevent short circuits when used in metal trays or conduits and

enables the tape to be folded at right angles to allow easy routing.

Condensation detectors shall be able to provide early warning of the condensing

conditions in chilled beam/ceiling systems to avoid the possibility of the indoor

rain. The detector shall have relay output for direct connection to the controller.

The sounder shall give audible alarm when any sensor operates. It shall be

complete with electronic oscillations, magnetic coil (sound coil) and accessories

ready for mounting (fixing). The sound output from the Hooter should not be less

than 85 decibels at the source point. Controller Technical Specifications

i) No. of Zones 2

ii) Events 500 event log

iii) Control keypad 20 button illuminated keypad

iv) Display 16 Character LCD on control keypad

v) Water leak Detector

vi) Response Time <1 Sec.

Encluding following accessories as required.

4 Zone WLD Control Panel along with Power Supply, In-built charger, Dry Contact

Relay with communication port for BMS

Detection/Sensing Cable 10 mtrs/length

Hooter with strobe

2C X 1.5 sq.mm copper Armored FRLS Cable for connecting Panel with

Make - C-System / Maser / Star Electronics

2.a. Complete Water Leakage Detection System Job 1 139,095 139,095

TOTAL DATA CENTER WORK AMOUNT 272,881.00

S.H. 6 HVAC WORK : AQM , NEW DELHI

Sr.No DSR No. Description Unit Quantity Unit Rate Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

1.a VRF/VRV OUTDOOR UNIT

Supply Installation, Testing & Commissioning of modular type Variable

Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling and heating, having all hermetically sealed inverter type

Scroll Compressor(s), minimum two compressors for above 14 HP modules,

microprocessor based Controller, top discharge type condensing unit(s), with

R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as

required.The unit shall deliver the rated capacity at AHRI Conditions and work

even at 50°C ambient temperature without tripping.The unit shall be suitable to

work on 400V+/-10%, 3 Phase, 50Hz AC power supply.The unit shall be filled

with first charge of the refrigerant and ready for use as required.The COP at

AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity

4-wayflow VRV/ VRF Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter, fan section with low noise fan/

dynamically balanced blower, multi speed motor, coil section with DX Copper

coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary

1.b 2 supports, vibration isolation, cordless remote control etc., suitable for operation

on single phase 230V±10%, 50 HzAC supply, complete, as required. The unit

shall have automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at air inl et

conditions of 27 Degree CD Band 19 Degree CWB temperature.

4-Way Cassette type

Hi-Wall Unit (With Condensate Pump)

1.b.3 MR Corded Remote controls Nos 1 4591 4591

1.b.4 MR Communication cable (1.5 sqmm X 2 Core) Rmt 20 157 3140

Supply, installation, testing and commissioning of MS fabricated outdoor unit

stand for placing outdoor unit of VRV system. The stand shall be

manufactured from MS C channel of minimum 3-4 mm thick. It shall be

finished with enamel paint as per client/architect approval.

2.0 REFRIGERANT PIPING

Supply,Installation,testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/hard drawn copper

DSR refrigerant piping for VRV/VRFsystem,complete with fittings,with suitable

2019 adjustable ring type hange rsupports,jointing/brazing including

VRF/VR accessories,insulated with XPLE Class-O tubular insulation/with Class-O closed

V cell elastometric nitrile rubber tubular sleeve ssections of specified thickness as

given below for Suction and Liquidlines,all accessories as per specifications

etc. as required :

2.1 5.5 19.1 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 30 707.0 21210

2.2 5.4 15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) Rmt 30 588.0 17640

CABLE TRAY FOR REFRIGERANT PIPING

Supplying and installing of following size of perforated hot dip galvanized G.I

cable tray with perforations not more than 17.5%, in convenient sections, joined

MR with connectors, suspended from ceiling with G.I suspenders including bolts

and nuts, etc. for carrying refrigerant pipe in outdoor application as required.

3.1. 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 0 1,106 0

3.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 10 740 7400

4.0 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete with

fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and

accessories as per specifications, drawings.

B CHAPTER-2: FRESH AIR DEMAND CONTROLLED ENHANCED VENTILATION

5.0 ZONE REGULATION DEVICE/VAV BOXES

Supplying, Installing, testing and commissioning of Pressure independent VAV

for climate control with multi-hop wireless mesh module, made out of heavy

gauge extruded alluminium of 1.5 mm nominal thickness consists of low

leakage extruded alluminium volume control damper with additional acoustic

cladding; Rapid Average Pitot tube; Air Flow Straightner (Honey-Comb

patterned); slab/duct temperature sensor or optional thumbwheel setpoint

adjustment. Dynamic factory calibrated and adjustable flow range of different

Note : Shall be ordered in site specific duct size without transition pieces and no

reduction in area for airflow measurement. VAV's shall be certified in

accordance with AMCA 611/511 for airflow measurement and leakage (Class

1.VAVs shall be pressure independent type & low velocity type

2.VAV Boxes shall be slow reacting type capable of delivering variable air

volume type by the action of opposed blade volume control damper

3.VAV boxes shall be supplied with end flanges for attachment to flanged

duct ends and shall be complete with all internal Acoustic treatment.

4.The casing shall be double skin type of Galvanized sheet steel construction

with a completely sealed, easily removable. The access shall be provided per

OEM and suitable to site.

5.VAV shall be electronically controlled networkable controller type complete

with low leakage damper, actuator , Microprocessor unit , wall/ ceiling

mounted temperature sensor with ON/OFF Switch , control transformer , unit

hander brackets etc.

6.VAV Boxes shall also be able to reset any air flow between zero and the

maximum air quantity that the boxes can handle without changing orifices or

other parts, but the boxes shall be factory set at 10% of the maximum flow as

7.The noise level from the VAV boxes shall not exceed 35 dbA

8.The temperature sensor and the entire control mechanism shall be fully

compatible with BMS System. Datas like temperatures, set points , damper

position shall be monitored through BMS system

9.Integrators for the below VAVs to connect with the BMS system to read and

modify the parameters. Integrator should release open protocol BACnet /

MODBUS to integrate with third party BMS System. The integrator shall be

approved through engineer in charge / consultant before procuring the VAVs.

11.Power wiring from the Socket to VAVs

The VAV shall be installed on the exisiting ductwork and the cost shall include

cutting of existing ductwork, fixing new pieces as required and rebalancing of

AHU to meet the requirement. No Extra cost shall be given

MR Pressure Independent zone regulation device on Existing Grilles/Diffusers

Supplying, Installing, testing and commissioning of Pressure independent zone

regulation device to maintain desired minimum or maximum flow rate at

rectangular supply air outlet without plenum box. Having Low leak extruded

airfoil multi-blade opposed blade damper for grilles/diffuser, area under given

size.. Made out of heavy gauge extruded aluminium airfoil blades and hat

type 65 mm deep frame, complete with exposed gear drive, EPDM blade

seal, and wire-free mesh networked zone control and actuator. The zone

regulators shall be installed in the collars of the diffusers, grilles per drawings.

6.0 Room Thermostats

Supplying, Installing, testing and commissioning of Room thermostats having

MR temperature, & humidity sensor; capacitive touch button with e-ink display; No. 18 4,853 87354

3.3V power supply and wire-free mesh control link.

C CHAPTER-3: AIR DISTRIBUTION SYSTEM

7.0. GSS DUCT (Factory Fabricated Duct)

Supply, installation, balancing and commissioning of factory fabricated GSS

sheet metal rectangular/round ducting complete with neoprene rubber

16.12.1 gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per

approved drawings and specifications of following sheet thickness complete

GSS DUCT (Site Fabricated Duct)

Supply, installation, balancing and commissioning of fabricated at site GSS

sheet metal rectangular/round ducting complete with neoprene rubber

8.0 16.12.2 gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per

approved drawings and specifications of following sheet thickness complete

9.0 Supply Air Grilles

Supplying & fixing of powder coated extruded aluminium Supply Air Grilles with

16.15 Aluminium volume control dampers of various sizes and as per specifications Sqmt 15 8,480 127200

and approved drawings and schedules.

10.0 Return Air Grilles

Supplying & fixing of powder coated extruded aluminium Return Air Grilles with

16.16 louvers but without volume control dampers of various sizes and as per Sqmt 20 5,507 110140

specifications and approved drawings and schedules.

11.0 EXHAUST/FRESH AIR LOUVERS

Supplying, Installing, testing and commissioning of powder coated extruded

aluminium exhaust air louvers with min.60 % free area, with metallic frame work

& fixing accessories, to be fixed on external wall to exhaust air from basement

MR area to ambient , it shall be suitable for exhausting required air in CFM . Louvers Sqmt 2 6164 12328

need to be suitable in order avoid rain water entry in to basement @ 15 degree

deflection with bird screen complete as per specification approved drawings

12.0 Supply Air Diffusers

Supply , installation , testing and commissioning of supply air diffusers of

Powder coated Aluminium with Aluminium volume control dampers with anti

smudge ring and removable core. Diffusers shall be as per specification &

16.17 the sizes will be as per drawings and schedules :

13.0 Return Air Diffusers

Supply , installation , testing and commissioning of return air diffusers of

Powder coated Aluminium without volume control dampers with anti smudge

ring and removable core. Diffusers shall be as per specification & the sizes

16.18 will be as per drawings and schedules :

14.0 COLLAR DAMPER

Supplying, installing, testing & commissioning of GI collar damper with

minimum 1.6 mm flange and 1.8 mm blade thickness within ducts to be

provided with suitable links, levers and quadrants for manual control of volume

of air flow and for proper balancing of the air distribution system as per

schedules & drawings.

15.0 Motorised Volume Control Damper

Supply, installation, testing and commissioning of motorised(ON/OFF Type)

duct mounted opposed blade G.I volume control damper with enthalpy

16.14 sensor and necessary control wiring (minimum 1.5 sqmm ) for integeration

within IDU room.The unit shall provided as shown in the drawings. The unit shall

be capable to communicate with BMS system.

16.0 Fire Damper

Supplying, Fixing,testing and commissioning of fire damper in supply air

duct/main branch and return air path as and where required of required sizes

i/c control wiring, the damper shall be motorized and spring return so as to

close the damper in the event of power failure automatically and open the

same in case of power being restored. The spring return action shall be inbuilt

mechanism and not externally mounted. the damper shall also be closed in

the event of fire signal complete as required and as per specifications.

16.2 16.20.2 Actuator (Rated torque-10 N.m/m2) Each 2 9212 18424

17.0 Back Draft Damper/Gravity Damper

Supplying, Fixing,testing and commissioning of Extruded aluminum of Minimum

0.050 inch (1.2 mm) thick backdraft damper with extruded aluminum blades

suitable for application in HVAC systems with velocities to 1,500 feet per minute

MR (305 m/min). The damper shall withstand -10 to 60 degree celsius temperature. Sqmt 0.5 5574 2787

Maximum back pressure of 6" w.g., Minimum air velocity of 1500 fpm.The

damper shall be complete as required and as per specifications.

D CHAPTER 4: INSULATION & ACOUSTIC

18.0 DUCT INSULATION

Supply and installation of cross linked closed cell Oxide Acetate Foam Thermal

insulation on ducts having density 0f 30 to 33 Kg/ M³ ,having K value 0.029

W/m ° K at 40°C Deg temp and temp range of -70°C to +100°C and fire rating

Class O as per BS 476 Part 6 from CBRI,Roorkee as per the approved

specifications. Smoke & Toxicity index of material shall be passed as per IMO

MSC 307 ( 88 ) 2010 Anexx 1 Pt 2.• Material shall be CFC/ HCFC free as per US

13mm thick insulation oxide acetate foam laminated with aluminium foil for

supply air duct

9 mm thick insulation oxide acetate foam laminated with aluminium foil for

Return air duct

19.0 MR DUCT ACOUSTIC LINING

Supply and installation of cross linked open cell acco isolate acoustic

insulation for duct having density of 30 to 55 Kg/ M³ ,having K value 0.029 W/m

° K at 40°C Deg temp and temp range of -70°C to +100°C and fire rating Class

O as per BS 476 Part 6 from CBRI,Roorkee as per the approved specifications.

Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 )

2010 Anexx 1 Pt 2.• Material shall be CFC/ HCFC free as per US EPA 5021

19.1 25mm thickacco isolate acoustic open cell insulation Sqmt 25 682 17050

20.0 MR AHU ROOM ACOUSTIC LINING

Supply and installation of cross linked open cell acco isolate acoustic

insulation for AHU room having density of 30 to 55 Kg/ M³ ,having K value 0.029

W/m ° K at 40°C Deg temp and temp range of -70°C to +100°C and fire rating

Class O as per BS 476 Part 6 from CBRI,Roorkee as per the approved

specifications. Smoke & Toxicity index of material shall be passed as per IMO

MSC 307 ( 88 ) 2010 Anexx 1 Pt 2.• Material shall be CFC/ HCFC free as per US

25mm thickacco isolate acoustic open cell insulation for Ahu acoustic

21.0 MR DOUBLE LAYER CANVAS CONNECTION

Supply,Installation,testing and commissioning of double Layer canvas

connection fire retardant cloth for the end connection of Ductable Units/AHUs

and Ventilation fan to reduce the vibration.It shall be fire rated for atleat 2 hrs.

Refer tender specification for detail description

E CHAPTER 5: VENTILATION SYSTEM

22.0 INLINE FANS

Supply , installation , testing and commissoning , of duct mounted inline fans

complete with direct driven centrifugal fan , TEFC squirrel cage induction

motor , with efficiency class IE-3 whichever is higher , direct drive arrangement ,

22.1 MR heavy gauge sheet metal casing , rubber isolator mounts and other

accessories.The fan shall be complete in all respect and should match the

specification ,Drawings and Schedule. Inline fans shall be of following

22.2 1100 CFM (15 mm Static Pressure) Nos. 4 19674 78696

23.0 MR CEILING MOUNTED EXHAUST FANS

Supply , installation , testing and commissoning , of ceiling mounted inline fans

complete with direct driven centrifugal fan , direct drive arrangement , heavy

gauge sheet metal casing , rubber isolator mounts and other accessories.The

fan shall be complete in all respect and should match the specification

,Drawings and Schedule. Inline fans shall be of following capacities.

F CHAPTER-6: DEMOLISHING AND TAB WORK

SHEET METAL WORK

Demolishing of existing ductwork of all sizes, Insulation, Diffusers, Grilles,

dampers in complete respect and clean the ceiling for new ductwork as per

the new RCPs, Zones, Spaces marked in the drawings. The contractor to

examine and ensure no damage to other services like electrcial, lighting

fixtures, smoke detectors, structure etc running in the ceiling shall be made. The

contractor shall be responsible to clean and shift the uninstalled ductwork and

place it on the ground at the location suggest by PMC/Engineer In Charge.

NO extra cost shall be paid in any manner.

G CHAPTER-7: ELECTRICAL WORK

Supply, installation, testing and commissioning of indoor/outdoor floor

mounted/ wall mounted, IP43/IP65, IS 61439 factory built, modular,

sectionalised, compartmentalized, extendable type LT cubicle panel of

suitable size suitable for operation on 433/415 volts, 50 Hz AC 3 phase 4 wire

supply system fabricated from CRCA sheet steel of 2mm thick for frame work

and covers, 3mm thick for gland plates with stiffeners wherever required,

having vibration free structure chemically treated with seven tank process or

better before painting for surface treatment and powder coated in approved

shade, with suitable electrolytic grade high conductivity bus bars extensible,

25.0 DMC/ SMC (whichever is superior) bus bar supports, with short circuit withstand

capacity as mentioned ,bottom base channel of section not less than 100mmX

50mmX 5 mm thick, fabrication shall be done in transportable sections, entire

panel shall have a common earth bar of required size at the rear with 2 Nos.

earth stud, connections and interconnection with solid conductor wires /

copper strips, neutral links, control wiring with 1.5 sqmm. & 2.5sqmm. PVC

insulated FRLS copper conductor S/C cable for voltage & current respectively,

including providing and fixing following switch gears and as per schedules

,technical specifications etc.complete as required.

415V, 50Hz, 160A, 4P, 25kA for 1 sec rated microprocessor based MCCB with

inbuilt LSIG protection - 1 Nos.

Metering (1 No.)

Multifunction meter with inbuilt selector switch for measurement of current,

voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line

and phase) complete as per specifications

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) -

LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on,

off, trip) - 1 set

415V ,160/5A, 15VA, CL-1 current transformer for metering

Busbar (1 Set - 4P + E)

Busbar made up of electrolytic grade high conductivity aluminium in

rectangular cross section and suitable for 415V, FP, 50 Hz, 300 A, 25 kA for 1 sec

of required length and cross sectional area.

5Nos. 415V, 50Hz,63A, 4P, 10 kA MCB.

Supply,installation,testing and commissioning of 63A 4P,Isolator , heavy duty

solid neutral link in a sheet steel enclosure with required arrangement for

incoming and outgoing cable complete as required.(Weather Proof)

Supply,installation,testing and commissioning of 40A 4P,Isolator , heavy duty

solid neutral link in a sheet steel enclosure with required arrangement for

incoming and outgoing cable complete as required.(Weather Proof)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

pipe from earth electrode including connection with G.I. nut,

26.1. 5.11 bolt, spring, washer excavation and re-filling etc. as required.Providing and Metre 100 483 48300

fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

Providing and laying earth connection from earth electrode with 6 SWG dia

26.2 5.12 G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with Metre 25 188 4700

G.I. thimble excavation and re-filling as required.

LT CABLE AND TERMINATION

Supplying, unloading, storing , laying, testing and commissioning of following

sizes of 1.1 kV grade XLPE insulated, FRLS (Heavy duty) Aluminium/copper

conductor armoured/unarmored cables suitable for working voltage upto

and including 1100 Volts, laid and tied on existing overhead cable trays; or

buried underground or laid and tied over MS supports in masonry trenches

including providing MS supports and clamps for fixing to supports in an

approved manner, providing fire retardant sealant where required complete

as required and as per specifications. Circuit identification tag should be

attached with the concerned cable alongwith the test report of following sizes

of cable to be submitted by the contractor at the time of delivery of material

at site. (Cable length may increse as per existing panel location).

Supplying and making end termination with brass compression gland and

28.0 9.1 aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

28.3 MR 4C X 6 Sqmm Each 2 200 400

Supplying following 1.1kV grade, XLPE insulated, FRLS type control

cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath,

29.0 outer sheath provided with FRLS insulation and with all components as

mentioned in BOQ, specifications and schedule, complete as required.

29.1 MR 2C X 1.5 sqmm copper conductor Metre 15 72 1,080

29.2 MR 2C X 2.5 sqmm copper conductor Metre 30 119 3,570

Supplying and making end termination with single compression brass gland

and lugs for following size of 1.1kV grade, XLPE insulated, FRLS type control

cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath,

outer sheath provided with FRLS insulation and with all components as

mentioned in BOQ, specifications and schedule, complete as required. The

cost shall include the cost of crimping and all tools and accessories required to

complete the job in full respect.

Note : Al lugs shall be used for Al cable and cu lugs shall be used for copper

30.1 MR 2C X 1.5 sqmm copper conductor Each 1 106 106

30.2 MR 2C X 2.5 sqmm copper conductor Each 1 123 123

CABLE MANAGEMENT

31.0 SOCKET OUTLET POINT WIRING

Wiring including termination for 6 amp socket outlet point with 3 x 2.5 sq. mm

PVC insulated FRLS copper conductor wires in concealed/exposed 1.6 mm

31.1 MR thick in MS conduits including providing 6 amp switch,3 pin 6A shuttered Nos 5 1,180 5,900

socket,anodised MS box for housing switches sockets, approved White

Polycarbonate modular cover plate and earthing.

Wiring including termination for 16 amp power socket outlet points with 3 x 4

sq. mm PVC insulated FRLS copper conductor wires for the 16 amp socket

outlet with 3 x 4 sq. mm PVC insulated FRLS copper conductor wires for the

second outlet of 650/1100 Volts grade in concealed/exposed 1.6 mm thick in

31.2 MR MS conduits as called for including providing 16 amp flush type combined 6 Set 2 5,994 11,988

pin shuttered sockets and switches, anodised MS outlet boxes for 16 A 6 pin

sockets and switches,approved White Polycarbonate modular cover plate

TOTAL HVAC WORK AMOUNT 2616370

S.H. 7 FIRE FIGHTING WORK : AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

A SPRINKLER SYSTEM

The main fire fighting sprinkler riser pipe including floor isolation valve, flow

indicating switch, inspectors-test-cum-drain assembly and drain pipe in

vertical shafts have already been installed by the main builder. The contractor

needs to make connections, alteration to existing main network only. All works

to be done after seeking permission from building manitenance agency.

1 Providing and fixing of following sizes of mild steel pipe, flanges and fittings

such as bends, tees, reducers, rubber insertions and galvanized nuts and bolts,

blank flanges, confirming to IS:1239-1974 Part-I and Part-II (Heavy Class)

with upto- date amaendments including fixing the pipe on wall/celing with

suitable galvanized strip/clamps/bracket and painting with one coat of anti-

corrosive paint/primer and two or more caots of synthetic enamel paint etc.

complete as required. (Jointing : Pipe Diameter up to 50mm - Screwed /

Groove Fittings, Above 50 mm - welded).

a. 25 mm nominal bore Metre 85 372.00 31620

b. 32 mm nominal bore Metre 50 458.00 22900

c 40 mm nominal bore Metre 40 529.00 21160

d 50 mm nominal bore Metre 35 690.00 24150

e 65 mm nominal bore Metre 20 863.00 17260

f 80 mm nominal bore Metre 10 1350.00 13500

g 100 mm nominal bore Metre 85 1678.00 142630

h 150 mm nominal bore Metre 5 1978.00 9890

A.2 Providing and fixing 15 mm dia gunmetal sprinkler head with quartz bulb and

set to operate at 68 deg. C.temperature. Sprinkler head shall carry UL-FM

A.2.a Chrome plated pendent type with powder coated twin rosette plate. Each 165 355.00 58575

A.2.b Chrome Plated/powder coated concealed type sprinkler head with all plates Each 10 972.00 9720

and accessories.

3 Providing and fixing 25 mm dia, 700mm to 1800mm long flexible stainless steel

(SS 304) pipe for making final connection of sprinkler head with sprinkler

system piping network including 2 nos. 25mm diameter G.I. connector, G.I.

Nipple, Reducer, elbow and threaded jointing complete as per detail.

4 Making connection with existing main header including butterfly valve,

flanges and accessories required.

A.4.a 150 mm nominal bore Each 1 8305.00 8305

5 Providing, fixing, testing and commissioning Ball valve with hard chrome

plated ball inside PTFE (Teflon) seat and ring with chrome plated centre

handle with female BSP2 threads complete in all respect. Minimum working

pressure 15 Kg/cm.

B PORTABLE FIRE EXTINGUISHERS:

1 Providing & fixing of clean agent gas based residue free stored pressure FE-36

Dupont- HFC-236fa (HEXAFLUOROPROPANE – CF3-CH2-CF3) multipurpose type

having 0% ODP with magnetic pressure gauge having the facility to check

with the magnetic pressure kit on site pressurised by dry nitrogen, can height

diamater is 108 MM Gross weight 3.6Kg, empty weight 1.6 Kg, discharge time

is minimum 6 sec, controllable discharge machanisim, embossed fire rating as

per the BS EN 3 - 21B, BIS 15683 marked with EPDM Hose with helium leak

detection tested and certificate enclosed, range 4 mtr with plastic yellow

safety seal with pull marked on it.

B.1.b Capacity 4.0 kg Each 2 24250.00 48500

2 Providing & Fixing of stored pressure Fire Extinguisher ABC powder type (Mono

Ammonium Phosphate Powder) Magnetic Pressure Gauge having the facility

to check at site, Discharge Time less than 9 Secs, Controllable discharge

mechanism, Range minimum 4 Meters, applicable on Class A,B,C and

Rating- 21A, Fire, 55B as per BS EN-3 BIS 15683 marked, Can Construction

: Deep drawn & CO2 Mig welded, Valve Construction : Forging & Machining,

Internal Coating of Can : Epoxy Powder coating, External Coating ofCan :

Epoxy Polyster Powder coating, Sheet metal thickness : 1.60MM, Helium Leak

B.2.a. Capacity 2 Kg. Each 4 8036.00 32144

B.2.b. Capacity 6 Kg. Each 4 12242.00 48968

TOTAL FIRE FIGHTING WORK AMOUNT 747642

S.H.8 FURNITURE WORK : AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT IMAGE

1 Chairman's Cabin Main Table

Providingin place of main table with overall size of table 2350 x 2350 x 750mm. The main table shall be of size 2350 x 1150

x 750mm. The side unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power

box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate

board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade Nos 1 115,959.00 115,959.00

and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one

side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type

which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft

closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

2 Chairman's Cabin Back Unit

The Back Unit shall be of dimensions 2350 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate

board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm

thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is

provided with lock for security. Nos 1 53,757.00 53,757.00

3 Chairman's Main chair

The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather

and moulded polyurethane foam. Size of back shall be (W)-46.0cm, (H)-57.0cm & size of seat shall be (W)-49.0cm x (D)-

49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2

kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the

mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable back

support to suitable individual need. Armrests should be pressure die casted in polished aluminium with PP arm tops. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt,

Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated while taking back support for

better adjustment of comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor.

The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia

(75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall

dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height

from ground - min 113.5 to max 138.0 cms. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations

shall be within +/- 1 cm.

Chairman's Visitor Chair

The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather

and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of

back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should

be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per

IS: 7888 for 25% compression. The back rest should be connected to the mechanism with a drop-lift mechanism which

can be adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual need. Armrests

should be pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall have following

features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt

tension adjustment knob should be operated while taking back support for better adjustment of comfort. The chair shall

be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of

die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm

pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene.

Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below.

Height from ground - min 93.5 to max 110.5 cm. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance /

variations shall be within +/- 1 cm.

5 Chairman's Sofa

Overall Size- Width: 231cm; Depth: 97.5cm; Height: 93cm. Seating Height: 46cm. Upholstery material shall be Fabric PVC

of thickness 1 mm. Material: Combination of plywood and pine Wood. Plywood thickness: 12 mm (moisture resistance

and termite free); Pinewood cross section ( without knots). Moisture content: 10 -12 %. Seat foam shall be Slab stock foam

of base density 28 kg/m3 and super soft 32 kg/m3 at top. Back foam material shall be Slab stock foam of 32 kg/m3.

Mechanism at Headrest can be adjusted at three levels. Webbing: Elastic belt with pocket spring of diameter 2mm. Legs

shall be MS pipe with metallic powder coated.

6 Chairman's Sofa

Overall Size- Width: 101cm; Depth: 97.5cm; Height: 93cm. Seating Height: 46cm. Upholstery material shall be Fabric PVC

of thickness 1 mm. Material: Combination of plywood and pine Wood. Plywood thickness: 12 mm (moisture resistance

and termite free); Pinewood cross section ( without knots). Moisture content: 10 -12 %. Seat foam shall be Slab stock foam

of base density 28 kg/m3 and super soft 32 kg/m3 at top. Back foam material shall be Slab stock foam of 32 kg/m3. Nos 2 31,081.00 62,162.00

Mechanism at Headrest can be adjusted at three levels. Webbing: Elastic belt with pocket spring of diameter 2mm. Legs

shall be MS pipe with metallic powder coated.

7 Centre Table

Providing in place of center tabe of following specifications. Overall Size shall be Width: 107cm, Depth: 81.5cm, Height:

46cm. TABLE Material shall be: TOP: SOLID TABLE TOP, LEGS: SOLID RUBBERWOOD. Color shall be WENGE.

Providing in place of Side table of following specifications. Overall Size shall be Width: 60.5cm, Depth: 60cm, Height:

46cm. TABLE Material shall be: TOP: SOLID TABLE TOP, LEGS: SOLID RUBBER WOOD. Color shall be WENGE.

9 Meeting Table

The overall size of the wortop shall be 3000mm x 1150mm x 740mm. Worktop shall be made from 25mm thick MDF one

side prelaminate board with 0.4mm PVC membrane pressed on to top and having chamfered edge. Soft closing dual

access flap provided for access to power supply and data cables. The Under-structure consists of mixture of 25mm and

18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving

the aesthetics.The product has a knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy Nos 1 67,584.00 67,584.00

polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for

standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for

mounting Audio Visual Cables(eg. HDMI,VGA-A,etc).

10 Meeting Chair

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm

Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with

leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu

molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm

x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest

support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height

adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360°

revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the

chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back

frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of

10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in

plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

11 Meeting Backside Chair

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with

leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu

molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm

x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest

support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height

adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360°

revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the Nos 4 17,856.00 71,424.00

chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back

frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of

10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in

plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Cabin Table A Main Table Providingin place of main table with overall size of table 2100 x 2250 x 750mm. The main table

shall be of size 2100 x 1050 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick MDF –

one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing

access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC

membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

12 approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre- NOS 5 105,803.00 529,015.00

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer

fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal

construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is

325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are

provided with lock for security.

13 Cabin Type A back Table

The Back Unit shall be of dimensions 1800 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate

board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm

thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is

provided with lock for security. nos 5 51,595.00 257,975.00

14 Cabin Type A main Chair

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic outer

and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density

= 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D.

The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03

cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type

tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The

armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be designed with the

following features : 360° revolving type, front-pivot for tilt with feet resting on ground and contionuous lumbar support

ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving options of

variable tilt angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black nos 5 41,562.00 207,810.00

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth

adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T

spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the

pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos.

of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to

15 Cabin Type A Visitor Chair

Providing and Placing in position Visitors. The cushioned seats shall be made of injection moulded plastic outer and inner.

Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2

kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The

back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x

0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The tubular frame shall be

cantilever type and made of Ø2.54±0.03 cm x 0.2±0.016 cm thick SS 202 tube. The back shall be connected to the frame

through chrome plated high pressure die cast connector piece.

16 Cabin Type B Main Table

Providingin place of main table with overall size of table 1800 x 2100 x 750mm. The main table shall be of size 1800 x 900 x

750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power

box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate

board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade nos 3 98,799.00 296,397.00

and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one

side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type

which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft

closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

17 Cabin Type C Main Table

Providingin place of main table with overall size of table 1650 x 1650 x 750mm. The main table shall be of size 1650 x 750 x

750mm. The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power

box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate

board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade nos 6 68,818.00 412,908.00

and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one

side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type

which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft

closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

18 Cabin Main Chair (type B & C)

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon

& upholstered using Quilted knitted fabric. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down

adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an

armrest top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The

lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The

height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad

has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment stroke of 10cm. The

pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black

polypropylene hub cap. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge.

This shall come along a headrest assembly consisting of polypropylene pad with lumbr support and covered with

polyester fabric. Neckrest assembly has an adjustment stroke of 4.2cm and otation adjustment stroke of 76 degrees.

19 Cabin Visitor Chair (type B & C)

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon

& upholstered using Quilted knitted fabric. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down

adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an

armrest top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The

lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The nos 21 14,337.00 301,077.00

height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad

has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment stroke of 10cm. The

pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black

polypropylene hub cap. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge.

20 Sofa 3 seater

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with

Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of

PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood

(which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and nos 6 38,400.00 230,400.00

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning

effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

21 Sofa 2 seater

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with

Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of

PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood

(which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and nos 11 34,752.00 382,272.00

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning

effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

22 Sofa 1 seater

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with

Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of

PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood

(which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and nos 7 26,430.00 185,010.00

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning

effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

23 Centre Table

Providing in place of center tabe of following specifications. Overall Size shall be Width: 107cm, Depth: 81.5cm, Height:

46cm. TABLE Material shall be: TOP: SOLID TABLE TOP, LEGS: SOLID RUBBERWOOD. Color shall be WENGE.

24 Cubicle Tables

The system shall be a desk-based system with a platform understructure made up of a combination of MS. Tubes and

plates. The size of the table worktop shall be 1350mm x 600mm and side unit shall be 900 x 450mm. The terminating leg

structure shall be in M.S. CRCA sheet/ tubes/rods as per IS. 513/7138/432 finished with epoxy power coating of the

approved colour as per the project designer. The modesty panel shall be of Acrylic (8 mm thick Acrylic both side frosted)

or of Metal 1.2 mm thick CRCA. The legs shall be provided with translucent glide screws to take care of the levelling as

per the site requirements Worktop shall be made of 25MM thick Pre-Laminated Board. All the edges of work surface shall

be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete

with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches

shall be on the wire tray/channel. Wire management shall be a part of the understructure and can be in the form of

enclosed metal tray or 2 level enclosed channel to provide concealed wire management throughout the cluster

formation. Provision for separation of Data and power cable shall be provided in the selected option. Wire riser leg or nos 13 55,530.00 721,890.00

independent wire risers shall be provided as per the layout structure. All the wire management components shall be of

MS sheet with varying thickness. Screen shall be provided as per the requirement of the design and layout. The screen

finishes can be selected from Fabric, laminated coloured glass, and DL marker board. Fabric screens shall be of 19 mm

overall thick, Glass screens are of 8 MM thick. The screens provided shall be complete with its set of PDC clamps for fixing

on the worktop. The screens shall be placed along the width of the worktop. For aisle side workstations it shall be along

the edge of the worktop while it shall be centrally placed for the Back to Back workstations. This must be UL Greenguard

25 Main chair (for cubical)

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon

& upholstered using Quilted knitted fabric. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down

adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an

armrest top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The

lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The

height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad

has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment stroke of 10cm. The

pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black

polypropylene hub cap. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge.

This shall come along a headrest assembly consisting of polypropylene pad with lumbr support and covered with

polyester fabric. Neckrest assembly has an adjustment stroke of 4.2cm and otation adjustment stroke of 76 degrees.

26 Visitor Chair

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon

& upholstered using Quilted knitted fabric. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down

adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an

armrest top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The

lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The nos 26 14,337.00 372,762.00

height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad

has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment stroke of 10cm. The

pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black

polypropylene hub cap. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge.

27 Workstations

Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht -

1200 including powder coated aluminium trims. The fins along the depth shall be 22.8mm thick. Tiles: Combination of

top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain metal/

prelam tile. Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel thickness comprises of

38mm (35 mm Minimum) thick paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or fabric on

both sides. The uprights and horizontals shall be made of aluminium extrusion having average wall thickness of 1.2 mm

& powder coated with epoxy- polyester powder. Particle board framing is used on outer boundary of these blocks as

well as intermediately at certain locations forming conduit for passing cables. These blocks are located in the

mid segment of the panels and can be provided with cutouts for mounting switch boxes (above or below the

worktops)Fabricated bottom frame for 52.4mm (50mm Minimum) panel comprises of L-channels made of 2mm thick nos 49 56,534.00 2,770,166.00

CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) & ERW steel tube of size 35 mm (30 mm Minimum)

x15 mm (10mm Minimum)x1.6mm thick in oval cross section (IS: 7138) welded together. This frame is bolted to the

uprights with M6 screws. Top tiles can be offered in variety of combinations. Worksurface- out of 25 mm thk prelam

particle board with flat pvc lipping edge banding of size 1350mm x 600mm x 750H. Brackets shall be made from 2mm

thick CRCA steel. Pedestals with legs - Nova pedestal flat metal front, free standing central locking of size 390 mm w

x 435 mm d x 646 mm height 3dr = 2box+1file. The work shall be carried out as per the instructions and guidance

received from engineer incharge.

28 L shape Workstations

Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht -

1200 including powder coated aluminium trims. The fins along the depth shall be 22.8mm thick. Tiles: Combination of

top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain metal/

prelam tile. Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel thickness comprises of

38mm (35 mm Minimum) thick paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or fabric on

both sides. The uprights and horizontals shall be made of aluminium extrusion having average wall thickness of 1.2 mm

& powder coated with epoxy- polyester powder. Particle board framing is used on outer boundary of these blocks as

well as intermediately at certain locations forming conduit for passing cables. These blocks are located in the

mid segment of the panels and can be provided with cutouts for mounting switch boxes (above or below the

worktops)Fabricated bottom frame for 52.4mm (50mm Minimum) panel comprises of L-channels made of 2mm thick

CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) & ERW steel tube of size 35 mm (30 mm Minimum) nos 7 67,591.00 473,137.00

x15 mm (10mm Minimum)x1.6mm thick in oval cross section (IS: 7138) welded together. This frame is bolted to the

uprights with M6 screws. Top tiles can be offered in variety of combinations. Worksurface- out of 25 mm thk prelam

particle board with flat pvc lipping edge banding of size 1350mmW1 x 1350mm W2 x 600mm x 750H. Brackets shall be

made from 2mm thick CRCA steel. Pedestals with legs - Nova pedestal flat metal front, free standing central

locking of size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file. The work shall be carried out as per the

instructions and guidance received from engineer incharge.

29 Workstation / Reception Chair

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane

foam and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility

just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers

impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped

spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form

the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be

adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The nos 60 13,725.00 823,500.00

adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled

Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled

Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors.

The overall dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

30 Board Room Table

Worktop shall be Made of 36mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top

and having chamfered edge. Plastic ABS access flap is provided for easy access to wires and cables. Work top is

available as per layout. The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2

grade and approved shade Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is

used for connecting panels together. Modesty panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2

grade Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work

surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated. An array of 17 30,190.00 513,230.00

panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and

cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece

injection moulded plastic part polymer component is fitted to pullout audio,video cables onto worktop and connect

devices charger to power socket below worktop.

31 Board Room Main Chair

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon

& upholstered using Quilted leatherette. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down

adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an

armrest top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The

lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The

height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad nos 1 17,601.00 17,601.00

has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment stroke of 10cm. The

pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black

polypropylene hub cap. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge.

This shall come along a headrest assembly consisting of polypropylene pad with lumbr support and covered with

leatherette. Neckrest assembly has an adjustment stroke of 4.2cm and otation adjustment stroke of 76 degrees.

32 Board Room Chair

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon

& upholstered using Quilted leatherette. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down

adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an

armrest top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The

lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The nos 16 16,435.00 262,960.00

height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad

has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment stroke of 10cm. The

pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black

polypropylene hub cap. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge.

33 Board Room Backside Chair

Providing and Placing Visitors Chair with overall size of 60.9 W m x 64.2 D cm x 98.2 H cm x 44.8 Seat Height cm. The seat is

cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded

high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression.

Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of

size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The tubular frame Nos 17 14,983.00 254,711.00

is cantilever type and made of Ø2.54±0.03cm x 0.2±0.016 cm thick SS 202 tube. The back connected to frame through

chrome plated high pressure die casted connector pipe.

It consists of storage units 457 mm deep– fixed or movable – bolted to Undercarriage which rolls onto the channels,

which, are firmly fixed to the ground. Each of above configurations can have following type of blocks – 1. Single Static

(SS) 2. Single Last (SL) 3. Twin Mobile(TM) – 2 body back to back. Construction shall be made out of 0.8 thk. CRCA Steel

conforming to IS: 513 Gr.D. Each body block (SS/SL/TM) building consists of 1 Main unit & then Add-on units (0, 1, 2, 3, 4 -

depending on no. of bays 1, 2, 3, 4 & 5). Each unit has 5 loading levels formed by 4 nos. adjustable shelves. Body units are

bolted to undercarriage. Optimizer Height from ground is 2080 mm (1980 body + 65 under-structure + 35 channel system).

Width shall be 915mm. The bodies including shelves are given anti-rust surface treatment & are powder coated with

epoxy polyester powder. Final finishing is done by a Dry Film Thickness of minimum 45 (+\- 5) microns. Shelves are having

10 bends & its max load bearing capacity is 80 Kg uniformly distributed per shelf. The Undercarriage is a welded frame

made of HR sheet 2 & 3.15 mm thk conforming to IS:1079 suitably fabricated to take the loads based on configuration.

The movement of units is achieved mechanically through a PU Drive wheel and 'Sprocket-Chain-Tensioner' arrangement

mounted rigidly onto body side. The torque from hand wheel is transfer to drive shaft via sprocket chain arrangement. ,

each movable undercarriage is provided with 3 rollers on the shaft for driving, 3 anti-friction ball bearings for rolling and 4

anti-friction ball bearings for guiding between rails. A Centralized locking arrangement is provided through Locking

Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together.

The nuts & bolts are galvanized / blackodized / Zn Plated. It consists of 'J' section 2 mm thk HR sheet & 25 mm Square

bright bar - both connected by screws. The movement of units is achieved mechanically through a PU Drive wheel and

'Sprocket-Chain-Tensioner' arrangement mounted rigidly onto body side. The torque from hand wheel is transfer to drive

shaft via sprocket chain arrangement.

Providing and placing ALL WOOD HINGED DOOR UNIT (HDU). Construction & Material Knockdown construction. Door

Opening Twin door with self closing hinges of Wood made from18mm Thick Pre Laminated Board. Handle · Aesthetically

appealing recessed plastic handle for& wooden Doors. Locking Mechanism Cam lock · 3 point locking mechanism in

Wood Door Shelving · Height wise Adjustable Shelf Mounting. Wooden Top shall be be made from Pre-Laminated Board

of 25 mm thk. Skirting of 125 mm High shall be provided. Leveler Screw type adjustable Leveler with plastic base. height.

Back Panel and Sides of the storageunits will be made out from 18mm thick Pre-Laminated Particle Board. Note: All

partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 10mm of

uneven flooring. The work shall be carried out as per guidance and instructions received from engineer incharge.

TOTAL FURNITURE WORK 11,665,602.00

S.H. 9 CIVIL & INTERIOR WORK: AQM , NEW DELHI

S.NO DSR Ref. No. DESCRIPTION OF ITEM UNIT BOQ Qty RATE AMOUNT

A FLOOR LEVELING

A.1 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering cum 20.00 6,259.10 125,182.00

and shuttering - All work up to plinth level :

4.1.5 a) 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).

2 IPS FLOORING

A.2 11.4 52mm thick cement concrete flooring with concrete hardener topping, under layer 40mm thick sqm 350.00 787.50 275,625.00

cement concrete1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm moninal size) and

top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone

aggregate 6mm nominal size) by volume, hardning compund mixed @2litre per 50Kg of cement or as

per manufacturer's specificatins. This includes cost of cement slurry but excluding the cost of nosing of

steps etc cmplete.

1 ITALIAN MARBLE

11.51 Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern

in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab

laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed

with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as

specified and as directed by the Engineer-in-Charge.

B.1.a 11.51.1 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc. sqm 140.00 5,986.20 838,068.00

2 8.11 Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer

work) including dado, skirting, risers of steps etc., in required design and pattern wherever required,

stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3

coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white

cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all

complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

B.3 8.11.1 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc. sqm 10.00 8,823.75 88,237.50

B.4 VITRIFIED TILE

11.41 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours

and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments

etc., complete.

5 FALSE RAISED FLOORING FOR SERVER ROOM

11.54 Providing and fixing removable raised/false access flooring with system and its components of

approved make for different plenum height with possible height adjustment upto 50 mm,

comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame

work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as

directed by Engineer-in-charge consisting of :

a) Providing at required spacing to form modular framework, pedestals made out of GI tube of

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size

100mmx100mmx3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check

nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in

position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate

using epoxy based adhesive of approved make or the machine screw with rawl plug.

b) S tringers system in all steel construction hot dipped galvanized of rectangular size

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head

using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the

pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate

solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted

clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per

the architectural drawings, as specified and as directed by the Engineer-in-charge.

c) Providing and fixing Access Floor panel of 600x600x30 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction

with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom

plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum64

welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated

for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip

noncombustible Portland cementitious core mixed with lightweight foaming compound. The access

floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology

upto1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to

withstand a Concentrated Load of 363 kgs applied on area 25mm x25mm without collapse in the

centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly

Distributed Load (UDL) minimum1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All

specification must be printed on the side of the panel to ensure the quality of the product.

B.5.a 11.54.1 300MM FINISHED FLOOR HEIGHT (FFH). sqm 10.00 5,075.30 50,753.00

6 ENGINEERED WOOD FLOORING

B.6.a MR Providing and fixing 15 mm thick Engineered wooden flooring with top layer of 3mm oak wood sq.m 355.00 6,533.04 2,319,230.10

sanded mat laqueed and bottom layer 10+2 mm of spruce wood of plank sizes of 190/205 mm x

2200mm h maufatured as per EN 14342:2005+A1 and certificates of JAS2 and CE and PEFC of

approved quality and manufacture, to be laid as per manufacture specification complete as per

direction of Engineer in Charge.

C FALSE CEILING WORK

GYPSUM BOARD CEILING

C.1 MR Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre

to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of

26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm

long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum

board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at

230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I sqm 380.00 1,739.87 661,149.91

MINERAL FIBRE ACOUSTICAL SUSPENDED GRIDE CEILING

C.2 MR 300MM X 1200MM MINERAL FIBRE GRID - Providing & Fixing of Mineral Fibre Acoustical Suspended sqm 220.00 2,728.12 600,185.48

Ceiling System with Bevelled Tegular Edge Planks With 15mm Exposed silhoutte Grid.

The planks should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance ≥85%, Thermal

Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6

&7) in module size of 1200 x 300 x 16mm , suitable for Green Building application, with Recycled

content of 35%.

The tile shall be laid on 15 mm wide T - section flanges having rotary stitching on all T sections i.e. the

Main Runner & 1200 mm Cross Tees with a web height of 38mm and a load carrying capacity of 12.67

Kgs/M2 & minimum pull out strength of 100 kgs.. The T Sections have a Galvanizing of 90 grams per M2

and need to be installed with Suspension system. The Tile & Grid system used together should carry a 30

C.3 MR Providing & Fixing of Micro-Perforated metal ceiling System consisting of 600x600mm Lay in tiles of pre sqm 30.00 3,609.57 108,287.09

coated galvanised steel in 0.4/0.5 mm thickness in white colour with perforation of 1.5mm dia & open

area of 22% with Freudenberg Soundtex acoustical fleece on the back of the tile to be laid on

Armstrong grid systems with 15mm wide T - section flanges colour white having rotary stitching on the

Main Runner, 1200 mm & 600 mm Cross Tees.

The tiles should have Humidity Resistance (RH) of 100%, NRC of 0.80, Fire Performance A2-s1.d0 in

module size of 600 X 600 mm, suitable for Green Building application, with Recycled content of 25%.

The grid should be 15mm wide T - section flanges colour white having rotary stitching on all T sections

i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm and a load carrying

capacity of 23.71 Kgs/M2. The T Sections have a Galvanizing of 120 grams per M2 & passed through

500 hrs of Salt test.

ACOUSTIC LINEAR CEILING

C.4 MR Providing and fixing of acoustical baffle ceiling of size 100mm x 25mm with C/c distance between sqm 50.00 7,321.19 366,059.61

baffles of 100/150mm including all necessary accessories & hangigng arrangement as per drawings &

directions of Engineer In Charge

C.5 MR 18MM thk Ply on periphery of the ceiling details as per architectural drawing to be suspended from sqm 50.00 2,039.28 101,963.99

ceiling with a provision for a cut out for light fixtures on it, taking self as well light loads, Complete in all

respect, as specicified Engineer in charge

C.6 MR Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy sqm 60.00 8,551.00 513,060.00

grade 6063. The baffle blade shall be in size of 100x 25 x 3600mm in Wood grain finish – Pradoo &

Cabrueava. The baffle blade shall be suspended using Slotted U-profile at center-to-center spacing of

upto 150mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with

50MM THK GI FRAM (FOR 100 MM THK PARTITION)

D.1 MR Providing and fixing metal system up to ceiling height, which includes frame work made of special sqm 425.00 877.27 372,840.56

section power pressed/ roll form G.I. sheet with zinc coating of 120 GSM, consisting of Boral U track

52mm wide having equal flanges of 30mm and 0.55mm thick (Base metal thickness) fastened to the

floor slab and ceiling soffit using rawl plugs with screw at 600mm centers, with first & last fixing point at

not greater than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, other

flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly within the flanges of floor and

ceiling channels located directly opposite to each other at not more than 610mm centers. Maintain 5

to 10mm gap between C Stud and web of U Track.

GLASS WOOL BETWEEN PARTITION (FOR 100 MM THK PARTITION)

D.2 MR Providing and fixing Glass wool insulation with Resin Bonded conforming to IS: 8183 having density 36 sqm 425.00 584.82 248,547.59

kg/m3, for 75mm thick partition wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel

plug & washers and held in position by criss crossing GI wire etc. complete as per directions of

Engineer-in-Charge.

GYPSUM BOARD FOR 100 MM PARTITION

D.3 MR 12.5 mm Standard board (conforming to IS 2095 Part1 1996; BS 1230: Part1: 1985 for Gypsum Board sqm 120.00 911.62 109,394.05

Type 1 & BS EN 520: 2004 Type A) is screw fixed to metal system on both sides using “type S” Boral Self

tapping 3.5 x 25mm corrosion resistant drywall screws spaced at 200mm centers on all joints and

300mm centers in the field of boards. Screw fixing is done mechanically. Finally, boards and screw

heads are to be jointed and finished so as to have a flush look which includes filling tapered edge and

square edges of board with Rapid Joint Compound, Paper Tape (As per recommended practice). All

perimeters and penetrations to be sealed with Acrylic sealant as per manufacturer’s specifications.

D.4 MR Providing and fixing 12mm thick commercial ply conforming to IS : 1328 type with necessary sqm 1,010.00 2,415.49 2,439,646.84

screws/nuts & bolts/ nails, including a coat of approved primer and anti-termite on one face, and

fixed on wooden / steel frame work, complete as per direction of Engineer-incharge (Frame work

shall be paid for separately).

D.5 MR Providing and fixing of 4mm MDF sheet on existing plywood partition / panelling with 4mm wide sqm 260.00 693.38 180,279.84

grooves in approved pattern complete in all respects with adhesive and all accessories as

required.The grooves to be finished using paint of approves shade.

GLASS PARTITION

D.6 MR Providing and fixing 12 mm thick frameless toughened glass Partition of approved brand and sqm 20.00 3,375.45 67,509.07

manufacture, including providing and fixing over aluminium channels embedded in the floor and

supported at the top as detailed. The Partition to be fitted firmly to the true ceiling with necessary

anchors / fastners. All the edges of the glass shall have pencil nosing and machine polished. the joints

in glass shall be filled with colourless silicon sealent all complete as per Direction of Engineer-in-charge.

E WALL FINISHING

E.1 MR Providing and fixing 1mm thick Laminate(as approved) and with painted horizontal and vertical sqm 160.00 1,175.40 188,063.70

grooves to match colour of laminate (as approved), for plain lining / cladding with surface as per

drawings & directions of Engineer In Charge.

E.2 MR Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary sqm 200.00 2,126.60 425,320.05

screws, priming coat on unexposed surface etc., complete

ACOUSTIC WALL PANEL

E.3 MR Providing and supplying Acoustical Wall Panelling with square edges made of fiber glass substrate sqm 80.00 9,272.62 741,809.55

25mm thick and wrapped on the front side with an acoustically transparent and fire-resistant fabric

with an option of colours as per the choice of the Architect/ Person in-charge of size 2100x600 or

600x600 mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using Wall

panel impalers suppied by the manufacturers

CERAMIC GLAZED WALL TILE

E.4 MR Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be Sq.m 120.00 1,372.33 164,679.14

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of size 600x300mm as approved by Engineer-in-Charge, in skirting, risers of steps and

dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey

cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching

shade complete.

E.5 PLASTER WORKS

E.5.a 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) sqm 75.00 254.25 19,068.75

E.6 PUTTY PUNNING

E.6.a 13.80 Providing and applying white cement based putty of average thickness 1mm of approved brand and sqm 120.00 115.15 13,818.00

manufacturer over the plastered wall surface to prepare the surface even and smooth complete.

DIGITALLY PRINTED FILM ON GLASS AND DOOR PARTITION

E.7 MR Providing & Fixing 3M Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to sqm 35.00 2,304.00 80,640.00

reproduce Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without

adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6

kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic,

Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be

endorsed by 3M India Limited Architectural Market Department. Contractors payment wouldn't be

released until & unless he/she produces orginal warranty certificate from the manufacturer.

E.8 MR Providing and fixing of blinds in band width 7.5 cm - 12 cm,made up of 100% polyster, in width of 250 - sqm 180.00 4,489.00 808,020.00

280 cm, weight -160g/sqm - 190g/sqm, thickness - 0.50 mm - 0.70mm ( opaue part ), Colorfastness to

light - above 4 grade. Blind tube is made of Aluminum with a diameter of min. 36mm, botom rail made

of Aluminum with powder coated having weight 390 gm/meter fitted with end caps in colour

matching to the fabric and mechanism to be of plastic with chain and metal bracket. The Blinds shall

be provided with Aluminum cover, matching the fabric designed on it. Aluminium profile should have

temper WP consisting of alloy 63400 along with anodizing of 10 micron and powder coating of 60

micron. The tensile strenghth of profile should be 9.10 Kg/mm square and elongation 18.The control

clutch drive unit engineered heavy duty chain drive pulley operating system consisting of gear clutch

housing and locking plug containing minimum 6 ribs and inserted at minimum of 38mm into roller tube.

It is self-lubricating Exclusive clutch with safety pins for secure bracket installation and unlocking pin for

quick manual removal. It shall be driven by a ball chain pulley with ball chain. Clutch gear ratio of

1.75:1 for reduced operating force on larger blinds.. Mounting hardware brackets universal brackets

including end plug bracket with lock down retainer device. Brackets finish of powder coated metal

installation brackets made of stamped and hardened steel. Roller tube circular-shaped aluminium

tube extruded from alloy 63400 and temper WP. Bottom rail flat-shaped extruded aluminium from alloy

63400 and temper WP. Ball chain shall be 2mm diameter cord with plastic balls moulded to form an

endless ball chain. It is used for raising or lowering action of the shades. Plastic parts all plastic

components shall be UV-stable compounds.

MOTOR FOR ROLLER BLINDS

E.9 MR Motorization (for MD cabin) Tubular Motor(RTS) for Roller Blinds / Motor Specs : PREMIUM Motor DM- No. 2.00 26,586.00 53,172.00

35R-6/28 . Radio Transmission System Torque(Nm) 6Nm SPEED (RPM) 28mm Rated Voltage (230 Volt)

Power Consumption(W)121 (W) Rated Current ( A) 0.53 amp Running time before thermal cut of (4

min.) Rated Frequency ( 50 Hz) Degree of Protection – IP44

E.10 MR Providing and fixing decorative wall paper on to partitions and wall etc. with approved adhesive over sqm 50.00 2,232.00 111,600.00

panelling in any shape, length etc. including preparing surfaces for wall paper (rate to include

wastage due to various sizes)

1) - Front vinyl and back is non voven

2) - washable 100%

4)- fire retardant

5)- moisture resistant

6)- ac controlling capacity

Marshall Factory series or equivalent

E.11 ACRYLIC EMULSION PAINT

13.82 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic

Compound ) content less than 50 grams/ litre, of approved brand and

manufacture, including applying additional coats wherever required,

to achieve even shade and colour.

E.12 13.68 French spirit polishing :

E.12.a 13.68.1 Two or more coats on new works including a coat of wood filler sqm 200.00 351.15 70,230.00

E.13 MR Providing and fixing 6 mm thick frameless toughened lacqure glass on existing partition/ coloums all sqm 60.00 2,240.00 134,400.00

complete as per Direction of Engineer-in-charge.

E.14 ACRYLIC SOLID SURFACE - Providing and fixing counters (vanity or in any other location) with 12 mm

thick acrylic solid surface manufactured as per ISO 19712-2. Solid surface used should be Microbial

resistant and resistant to mould growth, boiling water resistant, heat resistant, impact resistant, stain

resistant, scratch resistant as per ASTM G171 ( min 800 MPa), Green Guard certified and with a fire

rating conforming Class 1 as per BS 476 (Part 6 and 7). Acrylic solid surface having minimum density of

1.65 g/cm3, fixed over Aluminum Sections/19MM Marine Grade ply/ BWP board designed to support a

weight of 25 Kg. per Sqmtr. with suitable flexible adhesives (moisture cured Silicon Sealants) as per

manufacturer's specification and guideline, including fascia and back splash area as per approved

drawings and design. The Joints of Solid surface should be joined with adhesives having Low VOC of

238 g/ litre as per UL 2818 and SCAQMD.

E.14.a MR The Counter top should be finished with moulding of edges, buffing of surface, making of holes for sqm 15.00 13,250.00 198,750.00

plumbing fixtures, flushing of joints, installing of necessary hardware, sealing with silicon sealants, etc.

All complete as per direction of Engineer In charge. The Solid surface used should confirm to impact

resistance of more than 180cm in ball drop test as per ISO EN 438-2 Clause 21, The plan and elevation

area (horizontal and vertical) excluding wash basin area will be measured for payment. Fabrication to

be done as per the manufacturers fabrication manual, Solid surface manufacturer to provide 10 years

installed warranty on the works.

F DOOR AND ACCESSIORES

F.1 21.18 Providing and fixing 12 mm thick frameless toughened glass door sqm 15.00 4,447.00 66,705.00

shutter of approved brand and manufacture, including providing and

fixing top & bottom pivot & double action hydraulic floor spring

type fixing arrangement and making necessary holes etc. for fixing

required door fittings, all complete as per direction of Engineer-incharge

(Door handle, lock and stopper etc.to be paid separately).

F.2 MR Providing and fixing ISI marked 40 mm thick flush door shutters conforming to IS : 2202 (Part I)

decorative type, core of block board construction with frame of 1st class hard wood and providing

lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters

with Both Side Veneer as per specifications and Directions of Engineer In Charge.

F.2.a Double shutter upto, width 1.8m, ht. 2.4m sqm 4.00 16,656.00 66,624.00

F.2.b Single shutter upto , width 1m, ht. 2.4m sqm 60.00 16,656.00 999,360.00

2HOURS FIRE RATED METAL DOOR

F.3 MR SITC of fire door of rating for 120 Minutes, Conforms to IS3614 (PART-2)1992, BS476 (PART 20 & 22) and

Material: Door Frames and Leaves are made from Galvanized Steel

Door Leaves: Constructed from 1.0mm thick galvanized steel sheet formed to provide a 48mm thick

fully flush, double skin door shell with seamless welding joint all around. The internal construction of the

door shall be specially designed with infill to give 2 hours fire rating.

Infill: All the doors will have Honey Comb Crafted Paper or equivalent infill.

Door frame: Produced from 1.6mm galvanized steel sheet formed to single rebate profile of size125mm

x 57mm (+/- 0.3mm) with a maximum bending radius of 1.4mm. The necessary fixing arrangements

should be provided to mount the doorframes to the gypsum partition.

Vision Glass: 2 hours Fire Rated Vision Glass with 6mm thick clear glass in rectangular shape dimensions

of 200mm x 300mm to be fixed as per the given design.

Finish: The door frames and shutters are Zinc Phosphate with epoxy primer and finish with PU paint.

All doors should have suitable locking mechanism with 3 keys each.

• Automatic door closures, Seals for Air Tightness and Automatic Door Bottoms should be provided

* Contractor shall obtain and submit certificate

F.3.a Double Shutter, width 1.2m, ht. 2.4m sqm 8.00 76,000.00 608,000.00

F.4 SITC OF FOLLOWING DOOR FITTINGS

F.4.a MR Dorma BB 4330 or equivalent, 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x 3mm, in SS 304 and in nos. 48.00 455.00 21,840.00

SSS finish. Suitable for door weights upto 120kgs. Template Drilled (BB 4330)

F.4.b MR Dorma 278a or equivalent with 55mm backset, 20mm square forend prepared for euro profile cylinder nos. 6.00 4,504.00 27,024.00

including strike plate. and EPC 60mm Length both side key operation & Escutcheons in SSS Finish (278a

Dead Lock Type 1 Package)

F.4.c MR Pure 8100 Type 2 or equivalent Package with Pair of Pure 8100 Design Lever Handle on Roses & nos. 3.00 4,458.00 13,374.00

escutcheons. Including 271a Sash lock with 72mm CTC, 55mm Backset 20mm Square forend. EPC

60mm length one side key other side thumb turn operation (Pure 8100 Type 2 Package)

F.4.d MR Dorma pull Handle or equivalent TGDI-D 300 back to back with adjustable fixing for glass, wood and nos. 11.00 2,457.00 27,027.00

metal doors in satin stainless steel. The pull handles should have supporting washer with raised

bevelling on the outer surface. Length =300mm, 22mm dia, -SS304 (TGDI-D300)

F.4.e MR Dorma pull Handle TGDI-H 600 back to back with 500mm CTC, adjustable fixing for glass, wood and nos. 24.00 4,857.00 116,568.00

metal doors in satin stainless steel. The pull handles should have supporting washer with raised

bevelling on the outer surface. Length =600mm, 32mm dia, -SS304 (TGDI-H600)

F.4.f MR Dorma rack and pinion door closer or equivalent TS 72 EN size 2-4, with std. arm and with two nos. 7.00 5,951.00 41,657.00

independent closing valves and latching speed adjustable by arm. All adjustment screws face fixed .

Silver finish. As per EN 1154. (TS 72, 2-4, Std arm)

F.4.g MR Dorma floor spring BTS 75V EN or equivalent 1-4 with std. spindle and cover plate. The floor spring with nos. 15.00 12,082.00 181,230.00

backcheck and adjustable closing speed from 175°. With 90° hold open. As per EN 1154. (not suitable

for fire doors) Finish: Satin stainless steel. (BTS 75V EN 1-4 HO)

F.4.h MR PT 10 bottom patch or equivalent with insert for DORMA floor spring spindle, or round pivot 14 mm Ø. nos. 15.00 3,764.00 56,460.00

Finish:Satin Stainless Steel (PT 10)

F.4.i MR PT 20 top patch or equivalent with plastic socket for top pivot 15 mm Ø . Finish:Satin Stainless Steel (PT nos. 15.00 3,764.00 56,460.00

F.4.j MR PT 24 pivot or 15 mm Ø,with fixing plate, material thickness 6 mm, to let into ceiling. Finish: mill (PT 24) nos. 15.00 931.00 13,965.00

F.4.k MR center lock Round shape prepared for Europrofile cylinder, single throw, bolt projection 20 mm nos. 15.00 4,635.00 69,525.00

including epc one side key operation and one side knob operation and lock keeper plate. Finish:Satin

Stainless Steel

F.4.l MR Dorma dust excluding socket 3124 or equivalent with 16mm dia hole, fully morticed on the floor. satin nos. 10.00 545.00 5,450.00

F.4.m MR Dorma lever action flush bolt or equivalent with 19mm projecting bolt L=172 mm for wood door in satin nos. 10.00 886.00 8,860.00

chrome (3100-0)

F.4.n MR Dorma floor stop half dome or equivalent with 45mm dia with fixing accessories, in satin Chrome nos. 20.00 268.00 5,360.00

G DISMANTALING AND DISPOSAL OF EXISTING INTERIOR INFRASTRUCTURE

15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50

G.1 15.23.2 For thickness of tiles above 25 mm and up to 40 mm SQM 450.00 85.70 38,565.00

G.2 MR Dismantaling of existing wooden flooring including stacking of serviceable material and disposal of SQM 5.00 211.62 1,058.10

unserviceable material within 50 metres lead.

G.3 MR Based on Dismantling tile work in Wall dado laid in cement mortar including stacking material within 50 metres SQM 10.00 85.70 857.00

G.4 15.25 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and SQM 10.00 190.30 1,903.00

disposal of unserviceable material within 50 metres lead.

G.5 15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including SQM 15.00 39.00 585.00

disposal of rubbish to the dumping ground within 50 metres lead.

G.6 15.7 Demolishing brick work manually / by mechanical means including stacking of serviceable material

and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats,

architrave, holdfasts etc. complete and stacking within 50 metres lead:

G.8 15.12.1 Of area 3 sq. metres and below EACH 5.00 274.50 1,372.50

G.9 15.12.2 Of area beyond 3 sq. metres EACH 5.00 375.65 1,878.25

G.10 15.57 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including SQM 850.00 42.00 35,700.00

disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as

directed by Engineer-in-charge.

15.2 Demolishing cement concrete manually / by mechanical means including disposal of material within

50 metres lead as per direction of Engineer-in - charge.

G.11 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) CUM 5.00 1737.45 8,687.25

15.45 Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually /

by mechanical means breaking lead caulked joints, melting of lead and making into blocks including

stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-Charge:

G.13 15.44 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the

pipes, manually / by mechanical means including stacking of pipes within 50 metres lead as per

direction of Engineer-in-Charge:

G.13.b 15.44.2 Above 40 mm nominal bore RM 15.00 117.75 1,766.25

G.14 15.52 Dismantling of flushing cistern of all types (C.I. /PVC/Vitrous China) including stacking of useful Nos 6.00 668.15 4,008.90

materials near the site and disposal of unserviceable materials within 50 metres lead.

G.15 MR Based on Dismantling o Wash basins, Urinals, WC including stacking of useful material near the site and disposal Nos 12.00 391.20 4,694.40

item No 15.52 of unservicable materials within 50 metres lead

G.16 15.3 Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and cum 10.00 2534.70 25,347.00

disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

G.17 15.5 Extra for cutting reinforcement bars manually / by mechanical means in R.C.C. or R.B. work (Payment sqm 5.00 863.35 4,316.75

shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer - in -

G.18 15.6 Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work. kg 12.00 6.70 80.40

1.1 Carriage of material by mechanical transport including loading unloading and stacking

1.1.1 Lime, murrum, building rubbish

H 6.47 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick cum 12.00 6,636.95 79,643.40

AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel

level with approved block laying polymer modified adhesive mortar all complete as per direction of

Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

I SKIRTING & TRIM

I.1 MR Providing and fixing 1.5 to 2mm thick 50mm high extruded SS anodized aluminium skirting as per IS Rmt 390.00 550 214,401.20

standard pasted/fixed over 12 mm thick BWP ply with aluminium strip as per Architects approval.

I.2 MR Providing and fixing Window Cill of upto 450 mm wide, in 19mm thick pre-polished granite slabs of Rmt 120.00 1,550 185,986.58

approved shade, fixed on a bed of cement mortar 1:4, not more than 25mm thick, flushed with the

finished surface of wall, inclusive of pointing joints with neat cement slurry with pigmented additives to

match the shade of the tile, 6mm groove in the wall at the junction of granite and finished surface of

wall etc complete. Cost of pre-Polished Granite Rs.1,300/- per Sqmt.

J COUNTER WORK

J.1 MR Meeting Room Credenza: Meeting Room Credenza of size 450 deep x 3000 avg. length 800 high Nos 3.00 14,969 44,907.02

made up of 20 mm thk laminate finished top and sides,shutters etc. complete with necessary

hardaware and fittings as design & Drawing.

MR Providing and constructing full height storage of width and size as per drawings, with top, sides and

bottom in 19 mm thick commercial ply, back in 8mm thick commercial ply, intermediates in 19 mm

thick commercial ply, shutter hollow core with framework as per drawings in 19 mm thick commercial

ply, with 4mm thick commercial ply panel. All external surfaces to be finished in approved laminate,

with balancing laminate on the interior surface. All exposed edges to be finished in approved PVC

edge binding. Rate to include hardware such as approved locks, auto closing hinges for shutters,

approved handles, door stop, tower bolt, etc. complete.

MR 700 MM DEEP VENDING COUNTER :- Providing and fixing vending counter at pantry, counter made of

20 mm thk. (finished) granite top over BWP with 20x20 groove,base cabinet made of laminated

shutter of 19mm thick BWP(100% Gurjan with CCP technology) with shelves and partitions in balancing

laminate with edge lipping, 50mm high aluminium skirting, The rate inclusive of necessory hardwood

& ply backing, laminate finished, Sink with necessaary cut-outs,Hardware- SS Anodised Hettitch shutter

pulls 045206, self-closing hinges, spring loaded shutter latch inside, all cabinet hardware to be HETITCH

make & as/Architects approval Complete as per design and drawing. (Cost of Polished Granite Rs.

1,200/- per Sqm.)

K CEILING COVE

K.1 MR Ceiling Coves: Providing and making ceiling coves in 12mm thick gypboard/ply including necessory Rmt 150.00 195 29,209.43

support etc. complete with plastic emulsion paint and as per drawing.(Size-150 x 150mm)

L.1 MR Providing and fixing pelmets to Blinds made of 19 mm thick commercial ply, having clear internal Rmt 90.00 848 76,302.19

dimensions as 250 x 300mm, finished in approved laminate on all exposed surfaces from all external

surfaces and balancing laminate on all internal surfaces, supported from RCC ceiling slab by

necessary framework, giving additional supports in MS angles etc. complete. All exposed edges to be

finished in 6mm thick TW beading and finished in approved colour.

M MR COMPANY LOGO:- Providing and fixing three dimensional signage in Acrylic Sheet finish to match nos 1.00 45,702 45,701.83

brand colour shade of size approx. 450 mm x 1800 mm as per clients artwork. Average thickness of

Signage letter 25 mm acrylic & laser cut as per design and shop drawing, Base Rate Rs.40,500/-

N Reception Table 2200x1800x1050mm

N.1 MR Providing and fixing of reception desk lower level at 750mm height formed out of 19mm ply nos 1.00 99,749 99,749.21

framework, exposed internal surface shall be finished in approved shade of 8 mm thk acrylic surface,

as per details and Designs. The table shall be cladded with 8mm thick acrylic surface along the

edges/Fascia made of 50mm thick ply boxing frame work bent to shape as per design and drawing.

This shall also consist of Ply Box of Size 650mmx800mm @ 825mm level height from FFL. Made using

19mm thick ply box frame work, finished with 8mm thick Acrylic surface surface.The internal surfaces

and table top shall be finished with laminate surface as per approval.

300mm wide upper counter top at 1050mm level - Table top shall be formed out of 50mm thick ply

boxing frame work bent to shape as per design and detail and finished with 8mm thick acrylic surface

of approved shade as per design and details.

The facia to be finished in acrylic as per approved sample in curved profile.

The table to have in built 1 no drawer pedestal finished with laminate of approved colour and shade

as per details.Drawer to be complete with hardware installed as directed to consist of the following: 1

no multi purpose lock as specified, Telescopic channel, etc., complete as per details and Consultant's

O.1 MR Supplying and fixing of Toilet signages: Size: 150mmx 150mm imp.aluminum profile with 3 mm acrylic nos 7.00 656 4,590.05

Gents/Ladies pictograph printed on canvas: GENTS, PHYSICALLY CHAL., LADIES, PANTRY, MEETING

O.2 MR Providing and Fixing the Fire Exit Signages made up of Rigid integral PVC Cladded with Photo nos 10.00 947 9,471.54

luminiscent (Glow in Dark) material with computer cut vinyl lettering on it. Double sided and Single

sidded.As per architects Instruction. Fire makes and codes- readily available Make: Prolite

O.3 MR FIRE EVACUATION SIGNAGE - Fire Evacuation Signage: Material Clip-on (Aluminum Frame) with digital nos 6.00 3,312 19,870.36

print with lamination Fire Plan as per your Specification and Pasted the double sided 3M Tape. Size A3

O.4 MR Providing and fixing PUSH/PULL signage for all doors nos 32.00 285 9,113.87

O.5 MR IN CASE OF FIRE USE STAIRS' photo luminescent sign size: 200 x 200mm nos 2.00 431 861.05

P Providing & Fixing Passive Fire Stop Treatment as per:

P.1 MR Providing Fire expanding foam with minimum 2 hours fire rating when tested in accordance with BS sqm 20 14837 296730.728

476 part 20 and UL 1479 for horizontal openings in fire rated floors or slabs and vertical openings in walls

made of concrete/ masonry or Gypsum for passing service shafts. The expanding foam expands

seven times its volume to fill the cavity at the time of dispensing the material and shall fully cure within

two minutes after dispensing. The service lines could be of various types like electrical cables, cable

trays or metal pipes etc. The product shall be age tested for 30 years as per Dafstb and DIBT

standards. The product shall provide water tightness when tested for W rating as per UL standards and

shall be tested for providing a sound insualtion of 50 when tested in accordance with ASTM E 90.

The Application area should be cleaned. A suitable backing material should be used around metal

pipes or electrical cables and then the FireStop sealant should be dispended, the first few drops such

that only properly mixed materials will be used inside the opening (This can be known when the color

of the foam is red and not pale yellow).

UL Classified, FM,LPCB,BS 476-20,pr EN 1366-3

TOTAL CIVIL & INTERIOR WORK AMOUNTS 17,028,183.83

S.H.10 PLUMBING WORK: AQM , NEW DELHI

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.

waste fittings complete.

a MR 32mm flexible pipe Each 3.00 107.00 321.00

2 Providing and Fixing soil, waste and vent pipes

a 17.35.1.2 100mm dia Centrifugally cast (spun) iron socketed pipe as per IS: 3989 M 10.00 1,092.20 10,922.00

b 17.35.2.2 75mm dia Centrifugally cast (spun) iron socketed pipe as per IS: 3989 M 10.00 992.05 9,920.50

3 17.70.1 Providing and fixing PTMT Bottle Trap for Wash basin and sink. Each 7.00 335.25 2,346.75

Bottle trap 38 mm single piece moulded with height of 270 mm, effective

length of tail pipe 260 mm from the centre of the waste coupling, 77 mm

breadth with 25 mm minimum water seal, weighing not less than 263 gms

4 Providing and Fixing trap of self cleansing design with screwed down or hinged

grating with or without vent arm complete, including cost of cutting and making

good the floor and walls

a 17.60.2.1 100mm inlet and 75mm outlet Sand cast iron S&S as per IS - 3989 Each 12.00 1,579.45 18,953.40

5 Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and

fittings with paint of any colour such as chocolate grey or buff etc. over a coat

of primer (of approved quality) for new work.

6 Providing and fixing MS holder-bat clamps of approved design to Sand Cast

iron/cast iron (spun) pipe embedded in and including cement concrete blocks

10x10x10 cm of 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate

20mm nominal size) including cost of cutting holes and making good the walls

7 Providing and fixing bend of required degree with access door insertion

rubber washer 3mm thick bolts and nuts complete

a 17.38.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 3.00 461.65 1,384.95

b 17.38.2.2 75mm Sand Cast iron S&S as per IS-3989 Each 3.00 384.75 1,154.25

8 Providing and fixing plain bend of required degree

a 17.39.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 5.00 390.75 1,953.75

b 17.39.2.2 75mm Sand Cast iron S&S as per IS-3989 Each 3.00 289.95 869.85

9 Providing and fixing heal rest sanitary bend

a 17.40.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 3.00 432.20 1,296.60

b 17.40.2.2. 75mm Sand Cast iron S&S as per IS-3989 Each 3.00 363.35 1,090.05

10 Providing and fixing single equal plain junction of required degree with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a 17.44.1.2 100x100x100 mm Sand cast iron S&S as per IS - 3989 Each 6.00 667.70 4,006.20

11 Providing and fixing collars

a 17.57.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 7.00 409.45 2,866.15

12 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron

pipes & fittings of dia

13 17.59 Providing and fixing MS stays and clamps for sand cast iron/ centrifugally cast

(spun) iron pipes of diameter.

14 18.51 Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

a 18.51.1 15 mm nominal bore Each 6.00 552.35 3,314.10

15 Providing and fixing C.P. brass stop cock (concealed) of standard design and of

approved make conforming to IS : 8931.

a 18.52.1 15 mm nominal bore Each 6.00 606.25 3,637.50

16 Providing and fixing C.P. brass angle valve for basin mixer and gyser points of

approved quality conforming to IS : 8931

a 18.53.1 15 mm nominal bore Each 6.00 532.00 3,192.00

17 17.61 Cutting chases in brick masonry walls for following diameter sand cast

iron/centrifugally cast (spun) iron pipes and making good the same with cement

concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 12.5 m

nominal size) including necessary plaster and pointing in cement mortar 1:4 (1

cement : 4 coarse sand) :

18 18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 4.00 327.52 1,310.08

19 18.78 Making chases upto 7.5 X 7.5 cm in walls including making good after housing M 5.00 154.15 770.75

20 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC solvent cement and

the cost of cutting chases and making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

a 18.8.1 15mm nominal outer dia pipes M 50.00 409.65 20,482.50

b 18.8.2 20mm nominal outer dia pipes M 45.00 478.15 21,516.75

c 18.8.3 25mm nominal outer dia pipes M 20.00 561.95 11,239.00

21 Providing and fixing gun metal gate valve with C.I. Wheel of approved quality

a 18.17.1 25 mm dia. nominal bore Each 6.00 497.15 2,982.90

22 Providing and fixing unplasticised PVC connection pipe with brass unions.

a 18.21.1.1 30cm lengh &15 mm nominal bore Each 5.00 72.85 364.25

23 MR Providing and fixing white vitreous china clay wall mounted European type Water Each 7.00 59,904.00 419,328.00

Closet (EWC) with dual flush concealed cistern of approved make, of

approved shade similar to Jaquar Kubix KUS-WHT-35953BI or equivalent including

matching shade of plastic seat and lid cover, fittings, connectors, necessary

hanging arrangement, rubber buffers etc. including cutting and making good

the wall and floors wherever required, making connections to soil / vent pipe

etc., complete in all respects inclusive of cost of all required fittings, fixtures,

materials, labour, tools, tackles etc. as per specifications and direction of

Engineer-in-Charge.

24 MR Providing and fixing glazed vitreous China rectangular wash basin of 560x410

mm size of approved make similar to Jaquar Kubix KUS-WHT-35935 or similar with

MS or CI brackets painted white, C.P. brass chain with rubber plug, 32 mm CP

brass waste coupling of standard pattern, 32 mm CP brass bottle trap and

union, 32 mm dia C.P. pipes to wall flange etc. including cutting and making

good the walls & floors where required complete in all respects inclusive of cost

of all required fittings, fixtures, materials, labour, tools, tackles etc. as per

specifications and direction of Engineer in Charge

24.a a) White colour Each 7.00 7,108.00 49,756.00

25 17.10 Providing and fixing stainless steel sink of approved make with 40mm dia CP

brass waste coupling of standard pattern, CP brass chain & plug, 40 mm dia

PVC waste, CP grating including fixing under counter top, cutting and making

good the walls & floors where required complete in all respects inclusive of cost

of all required fittings, fixtures, materials, labour, tools, tackles etc. as per

specifications and direction of Site Engineer.

25.a 17.10.1 a) Stainless steel sink single bowl with drain board of overall size Each 1.00 5,155.95 5,155.95

510mmx1040mm, 250mm deep

26 MR Providing and fixing ivory coloured vitreous china flat back urinal basin set of Each 6.00 19,999.00 119,994.00

Urinals similar to Jaquar URS-WHT-132530 or equivalent approved make with auto

sensor flushing system with built in sensor including spreader, all fittings, brackets

for wall fixing, connection pipe, waste pipe etc. for individual urinal including

cutting and making good the walls and floors wherever required etc., complete

in all respects inclusive of cost of all required fittings, fixtures, materials, labour,

tools, tackles etc. as per specifications and direction of Site Engineer.

27 MR Providing & fixing 6mm thick, copper back finish, looking mirror of required size, Sqm 10.00 2,952.00 29,520.00

made of float sheet glass of best quality & approved make, over 12 mm thick

marine board fixed to rawl plug with round head screws and washers including

teak wood beading with melamine polish all around, complete in all respects

inclusive of cost of all materials, labour, tools, tackles etc. as per specifications

and direction of EIC.

28 MR Providing and fixing CP Central hole single lever wash basin tap with tuchfree Each 8.00 17,289.00 138,312.00

senser & popup waste system with 2 nos. 10 mm dia. 450mm long copper pipes

and brass nuts, size 15mm including cutting and making good the walls where

required complete in all respects as per direction of Engineer-in-Charge.

29 MR Providing and fixing sensor based CP brass tap with CP brass flange including Each 8.00 19,888.00 159,104.00

cutting and making good the walls where required complete in all respects

inclusive of cost of all materials, labour, tools, tackles etc. as per specifications

and direction of Site Engineer. Two way Bib Cock with wall flange.

30 MR Providing & fixing health faucet/ hand shower ABS body with 1 meter long PVC Each 7.00 1,610.00 11,270.00

tube and wall hook with flexible tube 8mm dia 1.5 m long.

31 22.5 Providing and laying water proofing treatment in sunken portion of WCs, Sqm 120.00 465.60 55,872.00

bathroom etc., by applying cement slurry mixed with water proofing cement

compound consisting of applying : a) First layer of slurry of cement @ 0.488

kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This

layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement

@ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm.

This layer will be allowed to air cure for 4 hours followed with water curing for 48

hours. The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed slurry.

32 22.14.1 Grading roof for water proofing treatment with cement concrete 1:2:4 (1 Cum 10.00 6,924.65 69,246.50

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

33 MR Providing & fixing Twin Toilet Paper Holder - Steel Twin Toilet Paper Holder - Nos. 7.00 3,638.00 25,466.00

Steel,Application : WC Cubicle Area

34 Provoding & fixing Automatic Hand Sanitiser Dispenser floor standing- High Traffic Nos. 2.00 35,758.00 71,516.00

Providing & Fixing of Automatic Hand Sanitizer , EHST3S or equivalent

35 Providing & fixing AUTO SOAP DISPENSER pluto PSD101 or equivalent Nos. 5.00 6,601.00 33,005.00

36 Providing & fixing SS finish sensor based hand dryer Pluto or equivalent model Nos. 5.00 31,694.00 158,470.00

37 Providing & fixing SS waste receptable bin of Kinox KWR or equivalent. Nos. 5.00 12,994.00 64,970.00

38 Supply and Installation of modular WC cubicles of width and depth as per Nos. 4.00 46,817.00 187,268.00

specifications/ drawings. Cubicle height to be upto 2100 mm.

ITEM DESCRIPTION

Made from solid grade compact high pressure laminate as per IS:2046

manufactured under high specific pressure > 5 MPa and temperature >120oC

with bunch of kraft papers impregnated with thermosetting phenolic resin and

decorative papers made of Alpha cellulose fiber impregnated with

thermosetting melamine resin which provide superior scratch, abrasion, heat,

chemical, impact, graffiti & moisture resistance along with anti-bacterial

properties. Panels have a black core that when machined, presents a distinctive

black edge. Panel thickness 12 mm. Design no. as specified by Arch. / Engr. in

suede finish. Size of panels to be as per drawing and verified as per site.

HARDWARE & ACCESSORIES

• Rectangular head frame structure made from Stainless steel grade 304.

Surface finish to be brush type. A thin plastic film pasted for surface protection.

Size to be 55mmx42mmx1.6 mmT.

Corner joinery section made from Stainless steel grade 304. Surface finish to be

brush type. A thin plastic film pasted for surface protection. Size to be

35mmx15mmx0.8 mmT.

Wall joinery section with hamming profile made from Stainless steel grade 304.

Surface finish to be brush type. A thin plastic film pasted for surface protection.

Size to be 21mmx16mmx0.8 mmT.

• Adjustable Palm Design Pedestal Footing of base diameter 64 mm made from

Stainless steel grade 316 giving a clearance height of 150 mm. Surface finish to

• Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish

to be matt type. Covers to be lacquer coated.

• Conical shape Coat hook with rubber stopper made from Stainless steel grade

304. Surface finish to be matt type.

• Round Door knob diameter 30 mm with grooves for better hand grip made

from Stainless steel grade 304. Surface finish to be matt type.

• Rotating Thumb-turn locking system with privacy indicator made from Stainless

steel grade 304. Surface finish to be matt type.

• Anti-noise rubber padding of thickness 2 mm and width 10 mm

• Stainless steel grade 304 screws.

• Anti-rotation Nylon polyamide grade-6 expandable wall plugs.

Partition system made out of Aluminium Extrusions around 2mm thick and

anodised around 15 micron.Size 25x45mm at top and bottom .The Partition to

have vertical portals to house the service cable.The portals to be on the door

side as well as on the corner and junction with solid wall.

The wall starter shall be 105/more x105mm/more.The partition sections to be

suitale to be clubbed with any type of door frame and door shutter(Sliding or

hinged door). The sections to be stable enough to accept glass thickness 10mm

toughened glass also.The partition sections to be available in anodized finish in

any RAL color as approved by the architects.The Partition should be

demountable and easy to install and maintain.The glass joints to be finished with

matching aluminium alloy I,T and corner sections suitable for 10mm thick

toughened glass.Color of frames: Matt black /Andonised finish.

Cubicles: Std Sizes (W x D x H)- 900 mm x 1550 mm x 1980 mm ( Height is

including 150 mm gap from bottom) Door Size- 600 mm

39 Providing and fixing urinal divider panel made up of 12mm thk. Compact Nos. 4.00 6,477.00 25,908.00

laminate using baracket.

TOTAL PLUMBING WORK AMOUNT 1,760,983.73

S.H. 11: EPABX: AQM , NEW DELHI

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

A EPABX SYSTEM

Supply, Installation,Testing and commisioning of Executive Level IP Phone with

1 display 3.5 inch , mulit giga ports, with basic codec supports complete as 14 Nos 22512.00 315168.00

Supply, Installation,Testing and commisioning of desktop Level IP Phone with

display 2.8 inch, Giga ports, with basic codec supports complete as required

Cetrlized communication system with : SITC of IP office SMB model, IP office

R10+IP 500 E1 additional 22 channels LIC:CU two cards, IP office R10+ IP end

point 1 LIC:CU , IP office R 11 essential edition LIC:DS, power cord india, IP

office ISDN cable RJ 45/ 3m Red, IP office 500 trunk card primary rate universal

dual , IP office IP500 rack mounting kit, IP office 500 version 2 control unit, IP

office IP500 V2 sysytem SD card A -Law, IP office media card voice (VCM)

coding module 64 v2 with liscense and Support of 3 years including within the

TOTAL EPABX WORK AMOUNT 2131167

S.H.12 AV WORK: AQM , NEW DELHI

S.No. DSR 18 Description Unit Rate

1 Display System

1.01 MR SITC of 75" 4K LED smart TV Display,20W Speaker output, 100Hz refresh rate, 3HDMI, Nos 1 294,248.00 294,248.00

2USB & Speacial features like File support Direct vieweing of PPT, Word ,PDF, Images

and video from pen drive, EXTERNAL CONTROL RS232C(in) thru stereo jack, RJ45,

1.02 MR SITC of 65" 4K LED smart TV Display,20W Speaker output, 500Hz refresh rate, 3HDMI, Nos 1 98,695.00 98,695.00

2USB & Speacial features like File support Direct vieweing of PPT, Word ,PDF, Images

and video from pen drive, EXTERNAL CONTROL RS232C(in) thru stereo jack, RJ45,

1.03 MR SITC of Table Top Cable Manager { With 1xHDMI,1xData,1X Voice, 1x6A Power Nos 8 12,557.00 100,456.00

Socket, 1X 6A Power Switch

SUB TOTAL- DISPLAY WORK 493,399.00

2 Audio System

2.01 MR SITC of 128 x 128 channels of AVB • 12 mic/line level inputs with AEC, 8 mic/line Nos 2 355995.00 711,990.00

level outputs • Gigabit Ethernet port • Up to 8 channels of configurable USB audio

• RS-232 serial port • 4-pin GPIO • Rack mountable (1 RU) • Fully compatible

with Tesira AVB DSPs, amplifiers, expanders, and controllers • Supports port

authentication via IEEE 802.1X • Internal universal power supply • SIP VoIP

interface via a RJ-45 connector • Standard FXO telephone interface via RJ-11

connector • Signal processing via intuitive software allows configuration and

control for signal routing, mixing, equalization, filtering, delay and much more • CE

marked, UL listed, and RoHS compliant

2.02 MR SITC of 24 Port Ethernet AVB Switch. Gigabit Smart Switch. 100-240VAC, 50/60Hz, 1 A. Nos 1 44111.00 44,111.00

Gigabit Smart Switch. BSS AUDIO | 8760 S. Sandy Parkway |

2.03 MR SITC of Ceiling Speakers 2 way loudspeaker system with 8 inch woofer size of Nos 5 4915.00 24,575.00

material polypropylene and tweeter size of 1 inch. mounting system: 3 screws 100V

transformer power taps 20 - 10 - 5 watts 70V transformer power taps 6 20 - 10 - 5 - 2.5

watts impedance66 ohms low impedance dynamic power:60 wattsbw impedance

RMS powerBD watts SPL 1W/1m66 dBmax SPL 1m604 dB frequency response® - 20K

Hzmain construction materialOBS plastic grille main materialoluminiumo ratingi

applicable low impedanceyesopplicable in 100Vyes Vertical dispersion angle 1000

Hz680°Olosest RAL colour (subject to deviations)6AL9010 (W) / RAL9011 (BL) Net

weight product040 kg

2.04 MR SITC of Ceiling Mic Diameter, Ceiling microphone array with Dimensions(L x B x H) 4 187564.00 750,256.00

590 x 590 x 43 mm20.5CM patented automatic speaker position detection and

dynamic beamforming for best speech intelligibility

• Analog and digital (Dante™) audio outputs for easy connectivity to video and

audio conference systems

• Configuration and monitoring via Sennheiser´s unique Control Cockpit software

• Open API for media and camera control applications

• 802.1X network configuration via SSH

• Several installation options via suspension kit, flushmount or surface bracket

Audio Output 1 x 3-pin terminal, 2 x Digital Dante Network Audio, 1 x RJ-45 Ethernet

Port for PoE power supply and data/control communication, voltage 44 – 57 V DC

(PoE IEEE 802.3af Class 3), Power consumption max. 8.8 W

SUB TOTAL- AUDIO SYSTEM 1,530,932.00

3 Swicthing and Automation Control System

3.01 MR SITC of high-quality 8X8 matrix switcher for 4K@60Hz (4:2:0) HDMI signals and Nos 1 430460.00 430,460.00

embedded audio. It reclocks and equalizes the signals and can route any one of

eight HDMI, HDCP-compliant sources (selectable) to any or all outputs

simultaneously. VS-88UHD offers a flexible audio scheme where any HDMI digital

audio input can be routed to any HDMI digital audio output in addition to ARC

support to produce an equivalent 16x12 audio matrix. Max. Data Rate — 8.91Gbps

data rate (2.97Gbps per graphics channel). Max. Resolution — 4K@60Hz (4:2:0).

Independent 16x12 Audio Matrix — With 8 embedded digital inputs + 8 ARC inputs

and 8 digital outputs + 4 ARC outputs. Kramer Step-In Over HDMI Technology. HDMI,

HDCP and DVI Compliance. Selectable HDCP Off per Input. Memory Locations — 16

presets for quick access to common configurations. Advanced EDID Management

per Input. Active Source & Acceptor Detection. Automatic Input Selection — Based

on priority selection or last connected input. HDMI Support — Deep Color, 3D, ARC,

up to 7.1 uncompressed audio channels. Kramer reKlocking™ and Equalization

Technology — Rebuilds the digital signal to travel longer distances. Embedded

Pattern Generator — With selectable patterns. Lock Button — To prevent tampering.

Kramer Protocol 3000 Support. Firmware Upgrade — Via mini USB, Ethernet or the RS-

232 port. Control Options — RS-232 serial commands transmitted by a PC, touch

screen system or other serial controller. Ethernet port via LAN, embedded Web pages

via LAN for configuration

3.02 MR SITC of distribution amplifier for HDMI signals. It reclocks and equalizes the signal NOS 1 145,525 145,525.00

and distributes it to 8 identical outputs. Max. Data Rate — 6.75Gbps (2.25Gbps per

graphic channel). HDTV Compatible. HDCP Compliant. HDMI Support — Deep Color,

x.v.Color™, Lip Sync, CEC. 3D Pass-Through. EDID Pass-through — Pass-through

algorithm ensures Plug and Play operation for HDMI source and display systems.

Kramer Equalization & re-Klocking™ Technology — Rebuilds the digital signal to travel

longer distances. Active Output LED Indicators. Worldwide Power Supply — 100-240V

3.03 MR SITC of master/space controller that can operate over Ethernet with control Nos 1 232206.00 232,206.00

interfaces that include: eight bidirectional RS-232, eight IR, eight GPI/O, and eight

relays. It controls devices such as scalers, video displays, audio amplifiers, Blu-ray

players, sensors, screens, shades, door locks, and lights. Multiple Kramer Ethernet

control gateways can be used to add remote I/O ports. Space Controller — Controls

any AV device/display with its corresponding logic. High Performance Architecture

— Enables a scalable and flexible programming platform. 8 RS-232 Bidirectional

Control Ports — For controlling devices via bi-directional serial control protocols. 8 IR

Emitter & 1 IR Receiver Control Ports — Control devices via IR control protocols and

learn commands from IR remotes. 8 GPI/O Control Ports — Control devices via

general purpose I/O ports, program configured as digital input, digital output or

analog input interface for controlling sensors, door locks, audio volume and lighting

control devices. 8 Relay Control Ports — Control devices via relay contact closure,

such as opening and closing drapes, shades, blinds, and projection screen scrolling.

Network Support — 10/100/1000Mbps Ethernet

3.04 SITC of Supported devices for wireless mirroring iOS, iPadOS, Android, Windows, Nos 1 241559.00 241,559.00

macOS,Chrome OS, mirroring protocols AirPlay, Miracast (Peer-to-Peer and

MICE),Chromecast, vSolution Cast, file formats - GIF, JPEG, BMP, PNG, PDF, Word,

PowerPoint, Excel, Text, HTML, AVI, WMV, MOV, MP4, DivX, MKV, M4V, WLAN standards

802.11 ac/a/b/g/n (2.4 & 5GHz) 802.11 ac/a/b/g/n (2.4 & 5GHz)/ Network protocols

TCP/IP, HTTP, HTTPS, SNTP/NTP, SSL, SSH, UDP TCP/IP, HTTP, HTTPS, SNTP/NTP, SSL, SSH,

UDP, Security encryption for wireless WLAN WEP, WPA2, WPA2 Enterprise or IEEE 802.1X

WEP, WPA2, WPA2 Enterprise or IEEE 802.1X

RMS encryption, controlling Multi-touch display, web interface, room control

system, keyboard/mouse, optional remote control, etc.

SUB TOTAL- Swicthing and Automation Control System 1,049,750.00

4 Converters, Cable and Connectors

4.01 MR Supply, installation, testing and commissioning of of 2.5 Sqmm x 2 core(12AWG) ATC Rmt 50 171.00 8,550.00

copper Conductor, Insulated Cores,PVC Sheathed Speaker Cables .(as per actual)

4.02 MR Supply, installation, testing and commissioning of of Shielded twisted pair CAT6 Rmt 50 135.00 6,750.00

Cable (STP) complete etc as required. (as per actual)

4.03 MR Supply, installation, testing and commissioning of of 35' 15–pin HD & 3.6mm Stereo Set 2 11571.00 23,142.00

4.04 MR Supply, installation, testing and commissioning of of 12' 15–pin HD & 3.5mm Stereo Set 2 11385.00 22,770.00

4.05 MR Supply, installation, testing and commissioning of of Various Connectors For Above Set 2 15533.00 31,066.00

Mentioned Configuration etc. all complete.

4.06 MR Supplying and laying HDMI Cable with connector on both ends. One end to be Rmt 50 693.00 34,650.00

placed in False ceiling and other on conference table.

SUB TOTAL- Converters, Cable and Connectors 126,928.00