SPL REPAIR OF BUILDING NO. T-1, T-2, T-40 AND T-44 AT OLD CBS CAMPUS BHALRA , T-198 (OR LIVING /DH AT BTC-I, NCPIT SCHOOL, CBS BHALRA, FENCING AT JAI GHATI PUMP HOUSE AND OTHER SANCTIONED WORK UNDER AGE (I) BHALRA

Amount

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and disposal of unserviceable material, debris and rubbish to outside cantt area complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in in CM 1:6, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and disposal of unserviceable material, debris and rubbish to outside cantt area complete all as specified and directed.

75 mm thick plain cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, and laid in panels complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of bitumen 85/25 grade and three part of sand by weight all as specified and directed.

Taking down cement plaster or cement lime plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified and directed.

Rendering 10mm thick in cement mortar 1:6 on other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement, complete all as specified and directed.

15mm thick plastering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement but using integral water proofing compound as per manufacturer,s instructions, complete all as specified. Note : Integral water proofing compound shall be measured & paid seprately.

Supply only liquid water proofing compound, complete all as specifed.

Preparation of newly plastered surface of wall including cornices pilaster etc, and applying three coats of white wash complete as specified and directed.

Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of cement base paint over a coat of alkali resistant primer, complete as specified and directed.

Preparation of old plastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coats cement base paint of approved brand all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off outside cantt area complete all as specified and directed.

100 mm thick plain cement concrete (1:4:8), type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed

Factory made (rectified) precast concrete rubber moulded designer chequered tiles any colour, shape and size not less then 300mm x 300mm x 20mm thickness (compressive strength not less than 250 Kg/Sqm) set, jointed and pointed with grey cement and pigment over and including 20mm thick CM 1:6 screed bed or bedding layer complete all as specified and directed.

75mm thick PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in sub base of flooring finished even and rough, to receive floor finishes, complete all as specified and as directed.

25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) as in floor, finished rough to receive tiles above, complete all as specified & directed.

Non skid JOINT FREE coloured ceramic tiles 7 - 8 mm thick area of each tile exceeding 0.06 Square metre but not exceeding 0.11 Square metre in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

Glazed JOINT FREE ceramic coloured tiles in skirting/dado 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:3 as backing coat rough finished surface complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified and disposal of unserviceable materials, debris and rubbish to outside cantt area complete all as specified & directed.

Machine cut kota stone slab flooring, 20-25mm thick as per sample kept in GE(I)’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 20mm screed layer in cement mortar 1:6, rubbing, grinding and polishing to achieve mirror finish, complete all as specified.

Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified & directed.

Dismantling of RCC platform of any description and any position and disposal of unserviceable material, debris and rubbish to outside cantt area complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, slabs etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, complete all as specified and as directed.

Black Granite (of any type) tiles 18-20mm thick, machine cut, (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete. complete all as specified and directed.

RCC 1:2:4 type B-0 (Nominal mix) using 12.5mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Ditto all as per item No. 29.00 above, but fixing only

Dismantling posts or struts embedded in concrete (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground Concrete, brick work masonry etc complete all as specified

Excavation in post holes (or similar holes) each not exc. 0.50 cum, in any type of soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc. 25cm, watering and removal of excavated materials to a distance n. exc. 50m and making good surfaces, complete all as specified & directed.

Material and labour for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete all as specified and directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS. 1161- 1979 grade St.Fe-240 all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern from roof covering or in ridges, hips, valley gutter and similar works complete, all as specified and directed.

0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and directed.

Refixing galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and directed.

0.80mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Two coat of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete, all as specified.

Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5sqm but not exceeding 4.0 Square metre each including taking out hold fast complete all as specified and directed.

Taking down shutters of any description exceeding 1Square metre and not exceeding 2Square metre each, complete all as specified and directed.

30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

Factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24 (a) kiln seasoned and pressure treated all as specified.

30mm thick factory made solid panel PVC door shutter conforming as per IS-4020 made from MS tube of 19 Gauge thickness of size 19 x 19mm style and 15 x 15mm for rail covered with heat moulded PVC channel of 5mm thick and 75mm, 125mm, 125mm wide for top rail, lock rail and bottom rail on either side at 5mm thick 20mm wide cross PVC sheet of gap inserted for top rail and bottom rail, paneling of 5mm PVC sheet fitted in MS frame welded/sealed to the style at rail with 30mm wide, 5mm thick PVC sheet beading sides and jointed together with solvent cement adhesive etc including aluminimum mongry complete all as specified and directed. Make :- Rajshree/Kumar Arch

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Square metre each including taking out hold fast complete all as specified and directed.

Powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Aluminium anodised powder coated of approved colour, sliding type three track (02 glazed shutters and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick tinted glass and mosquito proofing net as detailed below complete all as specified and directed :- (i) Frame section 91.85 X 31.75 X 1.30 mm, section No. 8758 for top and sides rails and 91.85 X 31.75 X 1.20 mm for bottom rail, section No. 8687. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.50 mm, section No. 8820. (iii) Glass 5.00 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips bearing section No. 4407 and necessary handles, tower bolt etc. as directed. (v) Stainless steel wire cloth (vi) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vii) Locking arrangement and providing Namda rope to make the frames air tight.

Powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

4.8mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square exceeding 0.5 Sqm in each pane complete all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled (ISI marked), 100mm long, complete all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified.

Mild steel barrel tower bolts stove enamelled black of size 150mm ISI marked and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section of size 100mm ISI marked and fixed, complete all as specified and directed.

Extruded aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

18-19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame/aluminium work complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified.

50mm dia, polished, hard wood knobs fixed with screws complete all as specified.

150mm size hasp & staple, aluminium, safety type, including bolt to hinge plate and fixed with screws, complete all as specified.

150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified.

Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

Prepration of old painted wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified

25mmdia PVC coated curtain rails, with fixing brackets, stops, rollers etc fixed in repairs complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, complete all as specified and directed.

3mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire, staples all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire, staples, fixed in repair all as specified and directed.

Dismantling wall & ceiling board (fibre, pulp, insulation etc.) or insulation boards / slabs/ blankets, any thickness, including cover fillets, complete all as specified.

4mm thick non asbestos fibre cement building boards laid / inserted to anodised aluminiumsnap grid frame work for false ceiling of grid 605mm x 605mm with using 36.5mm x 23.5 mm x 1.5 mm thick main tee, 23.5 x 23.5mm x 1.28 mm cross tee and 25x25x1.5mm angles and hangers 6mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40mm x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.

PVC wall panelling made up of PVC hollow panels 25/30cm in width and 10mm thickness interlocking pattern of approved shade and design fixed to wall or ceiling all as specifed and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position exc 250 ltrs & n exc. 500 ltrs capacity complete all as specified and directed.

Dismantling existing water tank capacity 1000 ltrs complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position, including over flow and drain out pipe complete of 1000 litre capacity complete all as specified and directed.

Dismantling existing water tank capacity exc 250 ltrs & n exc 500 ltrs complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position, including over flow and drain out pipe complete of 500 litre capacity complete all as specified and directed.

20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight - 210 gms), fixed in repair, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

15mm dia GI steel water tubing ,medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

Fixing only 15mm dia GI steel water tubing, medium grade, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

20mm dia GI steel water tubing ,medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

Fixing only 20mm dia GI steel water tubing, medium grade, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

15mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe fixed in repair, complete all as specified.

20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe fixed in repair, complete all as specified.

Bib taps long body 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, fixed in repairs complete all as specified and directed.

Stop valve of cast copper alloy chromium plated (ISI marked), fancy type, screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, fixed in repairs complete all as specified and directed.

Pillar tap cast copper alloy with capstan head, fancy type, chromium plated (ISI marked), screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed shank and fly nuts screwed for iron pipe complete for 15mm bore pipe, fixed in repairs all as specified & directed

Stop valve of cast copper alloy screwed down high pressure, screwed both ends for iron pipe or for unions 20 mm bore, fixed in repairs complete all as specified and directed.

Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore and fixed in repair, complete all as specified.

Brass CP wash basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore and fixed in repair, complete all as specified.

Health Faucet, ABS body with 1 metre SS braided connection pipe for 15 mm bore pipe, fixed in repairs complete all as specified and directed. Make Jaguar, Cat Part No ALD CHR-593N or equivalent in other approved make.

PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints fixed in repairs complete all as specified and directed.

Vitreous china urinals, bowl type of size 430 x 370 x 340mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe), complete, fixed in repair, complete all as specified and directed.

Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) incl provision of cement concrte bedding, PVC 'P' or 'S' trap 100mm dia, connection to trap and fushing pipe, anti syphonage fixed in repairs complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white, complete incl flushing pipe, connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete fixed in repairs complete all as specified and directed.

Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling including cutting for and pinning in ends of brackets or erecting stand etc., fixed in repair complete all as specified and directed.

Toilet paper holder of brass, CP with flat recessed type fixed to wall with brass screw, fixed in repairs complete all as specified and directed.

Soap dish vitreous china white, any size fixed to plugs with brass chromium plated screws and wooden/plastic cleats, complete all as specified.

Towel rail brass chromium plated, 20mm dia, D-type, 60cm long between flanges, fixed in repairs, complete all as specified and directed.

PVC connection 15mm size with length 600mm with PTMT nuts fixed in repair, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed in repairs complete all as specified and directed.

Grating square 150 mm size of PTMT (Minimum weight 100gms), fixed in repair complete all as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed.

Mild steel sheet eaves gutters, thickness of sheet 1mm, galvanised class 3, half round with rounded edges complete all as specified and directed.

Cast iron 100mm dia rainwater socketed pipes with cement joints, without ears complete all as specified and directed.

Cast iron 100mm dia Bends or elbows, square, or obtuse complete all as specified and directed.

PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in trenches/ floors/ fixed to wall complete all as specified and directed.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches/ floors/ fixed to wall, complete all as specified and directed.

Demolition of cement concrete of any description and any position and disposal of unserviceable material, debris and rubbish to outside cantt area complete all as specified and directed.

PCC 1:3:6 type C-2 (using 40mm graded aggregate) as in surface channels and drains including necessary formwork, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Excavation over areas not exc. 1.5m deep in any type of soil and getting out, complete all as specified and directed.

Dismantling of old polythlene septic tanks 25 to 30 users and removing from site and filling the pit with excavated earth and making good the surface, complete all as directed by the Engineer-in-Charge.

Cylindrical polyetylene septic tank, type-4 color (UV stabilised) Terroacotta capacity 25 to 30 User, 1300 mm dia, length 2600 mm, 3 chambers and 2 manholes size of manholes 550 mm(dia). Dia of inlet & outlet pipe 160 mm Air vent 50 mm including backfill by 6 to 12 mm washed aggregate (Blue stone) and connect to existing soakage wakk as per manufacturer's instruction. complete all as specified and directed by Engineer-in-Charge. Make: Sintex/United/Supreme

Excavating in trenches, not exceeding 1.5metre wide and not exceeding 1.5metre depth for foundation, etc., and getting out in any type of soil, complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed wares, AC or reinforced concrete) 150mm dia set in cement mortar, complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes and tested; in cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate for 150mm dia bore pipes all as per SSR Part-I specifications, complete all as specified and directed.

Salt-glazed stone ware (SGSW) grade-A drain pipes 150mm bore laid and jointed in concrete bed complete including testing etc. all as specified and directed as per SSR Part-I specifications, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick any type of soil, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC 1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore complete all as specified and directed.

PCC 1:2:4 type B-1 (Nominal mix), using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed.

TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified & directed.

Removing excavated soils to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

1.00mm thick PVC 3D wallpaper water proof, self adhesive, anti oil with approved shade or design, sticks to walls or ceilings as per the manufacture's instructions, fixed in repairs complete all as specified and directed.

Soakage well 1.80m internal dia and 3.00 m depth including excavation in any type of soil, PCC 1:3:6, type C-1 (Using 20mm graded stone aggregate) as in footing stone honey comb/ solid masonry cement in cement 1:4, RCC cover slab filled with brick bats including intercepting chamber screen chamber and disposal of soil complete (Including filling and packing of old soakage well complete all as specified and directed) all as specified and as shown on drawing No CEUZ/TD/1202/03 Sheet 1/2 dt 14.10.14 and 2/2 dt 11.05.07. NOTE:- (a) During excavation if unexpected water is encounterted, the same shall be bailed out/de-watered by the contractor mechanically or manually without any extra cost. (b) The excavated surplus soil shall be removed to a distance exceeding 500mtr and not exceeding 1500mtr and deposited where directed.

Supply and fixed pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges, lock stike plate etc, size 125 x 60mm complete all as specified and directed.

Fixing only pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges, lock stike plate etc, size 125 x 60mm complete all as specified and directed.

Material & Labour for PCC 1:2:4 type B2 (40mm graded aggregate) cement concrete in surface channels and drains complete all as specified and directed by Engineer-in Charge

All as per item No 115 here-in-before but exceeding 1.5 m but not exc 3.0 m deep and getting out in any type of soil, complete all as specified and directed.

Material & Labour for plain cement concrete type D-2 1:4:8 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 (Using 20 mm graded stone aggregate) as in cills, lintels upto 1.5 metre clear span, steps, seismic and other similar band, plinth course, string courses, lacing courses, parapets and railing upto 60cm in height, copings, kneelers, apex stone, bed plates, kerbs etc and in similar works including weathering, slightly rounded or chamfered angles and throating and necesssary form work complete, all as specified and directed.

Supply only water proofing compound

Supply only broken brick coarse aggregate/ brick bats of 40mm nominal size

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including concealed PVC conduit of wall thickness not less than 1.8mm and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch/one bell/buzzer point using cable of different insulation colour for colour coding including modular white cover plate with frame for mounting modular switches, sockets, fan regulator etc including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 139 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and directed.

All as per the description of Serial Item No 139 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and directed.

All as per the description of Serial Item No 139 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 4 Sqm with 2.50 Sqmm copper conductor in green colour for as earth continuity conductor all as specified and directed.

LED light fitting 1x20 watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up cable of copper conductor size 3-core, 23/0.0076 from ceiling rose to light fitting connector complete all as specified and directed. Make :- HAVELL's Cat No LHEXARP7SN1W020 or equivalent in Crompton /Philips

Supply and fixing in replacement Modular switch 1 way 6A, 1 module, complete all as specified and as directed.

Supply and fixing in replacement Modular Socket, 6A, 2/3 pin combined 2 module, complete all as specified and as directed.

Supply and fixing in replacement Modular Switch Socket 6A/16A, 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fixing in replacement Ceiling rose surface bakelite three terminals 240 volts complete all as specified and directed.

Exhaust fan with louvers of size 300mm sweep, 900 RPM, 230 volts (single phase) complete with bolts, nuts & washers, embedded in the wall including provisioning of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to Exhaust fan for connection, complete all as specified & directed

Exhaust fan with louvers of size 250mm sweep, 900 RPM, 230 volts (single phase) complete with bolts, nuts & washers, embedded in the wall including provisioning of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to Exhaust fan for connection, complete all as specified & directed

Storage water heater (Geyser), vertical type, of 25 ltr capacity of inner tank, outer tank, syphon assembly, thermostat heating element upto 2KW, safety valve etc complete all as per manufacturer design and specifications including making of all fixing arrangements complete having BEE Five Star Rating including grouting of fastner /nuts and bolts and necessary PCC work all as specified and directed. (Make:- BAJAJ / Venus / Recold / Havells)

Storage water heater (Geyser), vertical type, of 5 ltr capacity of inner tank, outer tank, syphon assembly, thermostat heating element upto 2KW, safety valve etc complete all as per manufacturer design and specifications including making of all fixing arrangements complete having BEE Five Star Rating including grouting of fastner /nuts and bolts and necessary PCC work all as specified and directed. (Make:- BAJAJ / Venus / Recold / Havells)

LED light fitting mirror type with high output diffuser 2 feet, 10 watt, 220 V AC decorative colour in polycarbonate housing and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and directed. Make :- HAVELL's Cat No LHEXACP5IN1W010 or equivalent in Crompton /Philips

Angular Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fixing in replacment LED bulb 230 volt 09 watts, in warm white colour with maximum Lumen output (650 lm) complete all as specified and directed.

Bulk head luminaries complete with all accessories suitable for and including 1 x 10 Watts LED lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 Volts 50 Hz complete all as specified and as directed. Make : Havells Cat Part No LHEOAOP7UZ6W010 / Crompton Cat Part No LBHE-10-CDL

Supply and fixing in replacment MCB SP 5 to 32Amp 10 KA 240 Volts, 'C' Series, complete all as specified and directed.

Supply and fixing in replacment MCB SPN 40 to 63Amp 10 KA 240 Volts, 'C' Series, complete all as specified and directed.

Supply and fixing in replacment MCB FP 40-100Amp 10 KA 415 Volts, 'B' Series, complete all as specified and directed.

Supply and fixing in replacment Sheet metal enclosure factory made single door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way complete all as specified and directed.

Supply and fixing in replacment Sheet metal enclosure factory made single door for DB 240 volts with 200 Amps rated bus bar SPN 4 Way complete all as specified and directed.

Supply and fixing in replacment Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar TPN 8 Way complete all as specified and directed.

Supply and fixing in replacment Frosted candle -3W frosed 6500K consisting 270 lumen fixed in repairs, all as specified and directed.

Supply and fixing in replacment Ruby LED post top lamp, 15W, environmental friendly, lonng asthetically designed with symmetrical light, distribution, spun aluminium landscape luminaire with high power LEDs RUBYMINIPT 15 W LED 830PSYMTOPC of make Havells or equivalent.

Sub main wiring with two single core PVC insulated multistranded un-sheathed FRLS cable of size 2x4 Sqmm with stranded copper conductor, drawing into PVC conduit of suitable size with continuous PVC insulated multistranded unsheathed FRLS cable earth wire of 2.5 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Two run of 4 Sqmm wire, one run of 2.5 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

1100 Volt grade heavy duty cable PVC Insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hanger not more than 1 mtr apart including 4 mm suspension wire, one twin core cable flat or circular 16 sqmm stranded conductor, complete complete all as specified and directed.

Metal cutted hanging light ceilling pendant lamp with LED color changing bulb white, warm (pack of 3 sets)

LED outdoor UP Down wall light warm white, IP 65 water proof & shock proof body complete all as specified and directed.

Ceiling mounted decorative 3 Watt LED spot/COB light warm white (pack of four) complete all as specified and directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for

Material and labour for 100 mm thick PCC 1:2:4 type B-1 (using 20 mm graded aggregate) in flooring including finishing the surface even and smooth without using extra cement

Supply and fixing Pre-painted galvatume alumium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screwes as specified

Supply and fixing Pre-painted galvatume alumium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screwes as specified

Supply and fixing mild steel sliding door bolts (250mm long), Plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed

Supply and fixing mild steel pressed handles 150mm long, oval type, stove enamelled black

M&L for point wiring complete with cable PVC insulted, unsheathed, 1100V grade conforming t IS for one way SP, 5A with 1.5 Sqmm of cable of nominal area multistranded copper conductor FRLS drawn through and including 20mm PVC casing capping including accessories on wall/ floor/ ceiling (on surface) etc with 16G MS pressed steel terminal box with 3mm thick laminatedsheet cover for mounting switch, socket outlet etc complete with all accessories/ fittings inlcuding PVC insulted continous muli standard copper earth wire (1.5 Sqmm) and connected to common earth dolly complete for the following: (a) One light/ holder point or one fan point/ bell point controlled by one switch.

All as per item No 176 here-in-before but one 3/5 pin socket outlet, 5 Amps, on same board with cables 1.5 sqmm size with 1.5 Sqmm copper conductor cable green in colour as earth continuity conductor connected to main earthing specified and directed.

All as per item No 176 here-in-before but one 5 pin socket outlet, 15 Amps, on independent board with cables 4 sqmm size with 2.5 Sqmm copper conductor cable green in colour as earth continuity conductor connected to main earthing specified and directed.

All as per itemm No 176 here-in-before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size

Supply and fix of lamp holder PVC/Polycarbonate with cord grip cap suitable for pendent fitting complete all as specified and directed.

Supply and fixing in replacement bell buzzer ding dong AC 230 volt, single pole, Make - Legrand/ Havelles/ Anchor

Supply and fixing in replacement bell switch flush type 5 A flush button single pole one way. Make - Legrand/ Havelles/ Anchor

Supply and fixing LED tube light fittings 1x16 watt, 220V AC decorative box type with driver holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing in replacement switch piano type 5A flush button single pole one way complete all as specified & directed. Make - Legrand/ Havelles/ Anchor

Supply and fixing in replacement socket 2 in 1, 5 Amp complete all as specified and directed. Make - Legrand/ Havelles/ Anchor

Supply and fixing in replacemnent switch socket combination 5 in 1, 3 pin, 5 and 15 Amp flush type universal complete as specified and directed. Make - Legrand/ Havelles/ Anchor

Supply and fixing 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tabe and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire one twin core 10 Sqmm solid conductor all as specified and directed by Engr-in-Charge.

Demolition of galvanised barbed wire of any description and in any position complete all as specified and directed.

Supply and fixing Mild steel work in posts and struts in fencing including cutting tops to shape as directed including drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc). Necessary drilling, bolting or riveting. Conforming to Fe-290 grade E-165, complete all as specified and directed.

Supply and fixing Mild Steel straps (40x 6mm) including bolts (for fittings straps to angles incl drilling necessary holes). If required hooks (stay), heavy for large gates hook and pintle hinges large hasps and staples chains hand made sliding bolts, clamps, hold fasts, well ties, hooks for hanging fans, plain angle cleats for securing purlins to woord trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde, E-165, complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed ent to be fitted with washers and one hexagonal or square nut, n exec 5cm longa all as specified and directed.

Material & Labour for mild steel TMT bars 10mm dia and over, as in stiffner to hold the chain link fencing fixed with angle iron post, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply and fixing 600mm dia concertina coil securing or tying on angle iron Y shape including provision of mild steel wire stapples or steel pins etc

Supply only chain link MS galvanised fencing of mesh size (nominal pitch of wire) of 50mm and 3.15mm dia

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire, complete all as specified and directed.

Supply and fixing galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spcaing and straining and fixing to any type of standard rails straining bolt including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured) complete all as specified and directed.

Surface excavation n exec 30 cm deep and averaging 15 cm deep in soft loose/ had dense soil and getting out, etc complete all as specified and directed by Engineer-in-Charge

Add to Srl item No 197 here-in-before last item for every 3cm or part thereof above or below 15 cm average depth

Material & Labour for hardcore of borken stone or boulders of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface, etc complete all as specified and directed by Engineer-in-charge

Material & Labour for plain cement concrete type B-2, 1:2:4 (nominal mix) using 40mm graded crushed stone agg as in flooring subbases 75 mm thick including necessary form work etc, complete all as specified and directed by Engineer-in-Charge

Material & Labour for reinforced cement concrete, type A-1, 1:1, 5:3 (Nominal mix) using 20mm graded crushed stone agg as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc basement slabs under-reamed, piles and mass concrete, etc, complete all as specified and directed by Engineer-in-Charge

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundaiton and plinth beams, and similar work, vertical or to batter, etc complete all as specified and directed by Engineer-in-Charge

Material & Labour brick work built in CM 1:4 with old size B bricks straight or curved on plan exc 6m mean radius, etc complete all as specified and directed by Engineer-in-Charge

Material & Labour Brick work with subclass B bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 etc complete all as specified and directed by Engineer-in-Charge

Supply only PVC (SWR) pipes, 110 mm dia single socketed, in any length with rubber rings

Preparation of new unplastered surfaces of wall and applying two coats of white wash etc complete all as specified and directed by Engineer-in-Charge

VEER TRADERS (BID ID -3105549)

K S BUILDERS (BID ID -3111362)