Repair/Maint of Pump/Motor Set, STP Equipments and allied services at AF Stn Jaisalmer and Chandan at AF Stn Jaisalmer

Amount

Disconnecting suction/delivery lines and coupling, taking down from foundation base frame, opening including dismantling of centrifugal pump/mono block pump set of following capacity, electric driven 3 phase 415 volt and replacement of worn out spare parts including replacement of new gland packing and re-assembling, installation in the same location, commissioning & testing complete all as directed and directed. Notes:- (i) The spare parts required to be replaced shall be measured and paid for separately under the relevant items here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Centrifugal pump/mono block pump set of capacity 100/75 HP

Centrifugal pump/mono block pump set of capacity 60 HP

Centrifugal pump/mono block pump set of capacity 40 HP

Centrifugal pump/mono block pump set of capacity 30 HP

Centrifugal pump/mono block pump set of capacity 20 HP

Centrifugal pump/mono block pump set of capacity 15/12.5 HP

Centrifugal pump/mono block pump set of capacity 7.5 HP

Centrifugal pump/mono block pump set of capacity 5 HP

Centrifugal pump/mono block pump set of capacity 2 HP and 3 HP

Taking out existing unservicable submersible pump and motor of capacity 5 HP to 15 HP, 3 phase, 415 volts, electric driven bore well and disconnecting electrical connections and delivery out let pipe and dismantling the motor and pump set complete and lowering in bore well after repairing/replacement of spares parts including mechanical seal and nuts/bolts/washers of the same and testing including refixing of column pipes, submersible cables complete all as specified and directed. Notes : Repair work and spare parts of pumps and motor shall be measured and paid for separately under relevant items here-in-after.

Taking out existing unservicable submersible pump and motor of capacity 15 HP to 30 HP, 3 phase, 415 volts, electric driven bore well and disconnecting electrical connections and delivery out let pipe and dismantling the motor and pump set complete and lowering in bore well after repairing/replacement of spares parts including mechanical seal and nuts/bolts/washers of the same and testing including refixing of column pipes, submersible cables complete all as specified and directed. Notes : Repair work and spare parts of pumps and motor shall be measured and paid for separately under relevant items here-in-after.

Opening and reassembling of monoblock/centrifugal pump (motor) after rewinding & replacement of worn out spare parts including taking out the burnt winding and rewinding of monoblock/centrifugal pump (motor) following capacity, Three Phase, 415 volts with solid copper conductor (wire) superior quality of approved make, size & number of wire as per existing including insulation material, minor spares and replacement of unserviceable spare parts and reassembling the components & testing for function ability, complete, all as specified & directed. Notes:- (i) The spare parts required to be replaced shall be measured and paid for separately under the relevant items here-in-after. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Monoblock/Centrifugal pump (Motor) 100 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 75 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 60 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 40 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 30 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 20 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 15/12.5 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 7.5 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 5 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 2 HP to 3 HP capacity, 3 phase, 415 Volt, 50 Hz

Monoblock/Centrifugal pump (Motor) 1 HP capacity, 3 phase, 415 Volt, 50 Hz

Opening and reassembling of submersible motor after rewinding and replacement of worn out spare parts including taking out the burnt winding and rewinding of submersible motor 5 HP to 15 HP, Three Phase, 415 volts with solid copper conductor (wire) superior quality of approved make, size & number of wire as per existing including insulation material, minor spares and replacement of unserviceable spare parts and reassembling the components & testing for function ability, complete all as specified and directed. Notes: (i) The include opening of motor at site for damaging of existing stator winding if found burnt/damaged in front of concerned JE/AGE (E/M) after testing on site before taking to work shop outside MD land. Motors will be given for repairing as per the site condition and need for repair being maintenance work. (ii) The spare parts required to be replaced shall be measured and paid for separately under the relevant items here-in-after. (iii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Opening and reassembling of submersible motor after rewinding and replacement of worn out spare parts including taking out the burnt winding and rewinding of submersible motor 15 HP to 30 HP, Three Phase, 415 volts with solid copper conductor (wire) superior quality of approved make, size & number of wire as per existing including insulation material, minor spares and replacement of unserviceable spare parts and reassembling the components & testing for function ability, complete all as specified and directed. Notes: (i) The include opening of motor at site for damaging of existing stator winding if found burnt/damaged in front of concerned JE/AGE (E/M) after testing on site before taking to work shop outside MD land. Motors will be given for repairing as per the site condition and need for repair being maintenance work. (ii) The spare parts required to be replaced shall be measured and paid for separately under the relevant items here-in-after. (iii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply and fixing in repair/replacement of following parts for existing centrifugal /Monoblock pump set electric driven 3 phase 415 volt complete all as specified and directed.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 100 HP Pump (Primary and secondary). Make : SKF/ NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 75 HP Pump (Primary and secondary). Make : SKF/ NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 60 HP Pump (Primary and secondary). Make : SKF/ NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 40 HP Pump (Primary and secondary). Make : SKF/ NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 30/20 HP Pump (Primary and secondary). Make : SKF /NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 15/12.5 HP Pump (Primary and secondary). Make : SKF/ NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Deep Groove Ball/Roller bearing (Double sealed Ball bearing) for 7.5/5.0 HP Pump (Primary and secondary). Make : SKF/ NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per pump design. Both the bearings (as per pump Make) to be replaced at the same time.

Centrifugal/Monoblock Motor Cooling Fan for 100 HP

Centrifugal/Monoblock Motor Cooling Fan for 75/60 HP

Centrifugal/Monoblock Motor Cooling Fan for 30 HP to 40 HP

Centrifugal/Monoblock Motor Cooling Fan for 12.5 HP to 20 HP

Centrifugal/Monoblock Motor Cooling Fan for 5 HP to 10 HP

Centrifugal/Monoblock Pump motor MS coupling suitable for 100 HP motor (Beam, Jaw, Gear any type)

Centrifugal/Monoblock Pump motor MS coupling suitable for 75/60 HP motor (Beam, Jaw, Gear any type)

Centrifugal/Monoblock Pump motor MS coupling suitable for 30 HP to 40 HP motor (Beam, Jaw, Gear any type)

Centrifugal/Monoblock Pump motor MS coupling suitable for 20 HP motor (Beam, Jaw, Gear any type)

Induction Motor prelubricated ZZ bearing (DE and NDE) for 100 HP (Primary and secondary). Make : SKF/NBC/ TATA/FAG/ UBC. Note: The quoted rates include cost of two Nos bearing as per motor design. Both the bearings (as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for 75/60 HP (Primary and secondary). Make : SKF/NBC/ TATA/FAG/ UBC. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings (as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for 40/30 HP (Primary and secondary). Make : SKF/NBC/ TATA/FAG/ UBC. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings (as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated bearing (DE and NDE) for monoblock 20 HP. Make : SKF/NBC/ TATA/FAG/ UBC.

Induction Motor prelubricated bearing (DE and NDE) for monoblock 15/12.5 HP. Make : SKF/NBC/ TATA/FAG/ UBC.

Induction Motor prelubricated bearing (DE and NDE) for monoblock 7.5/5.0 HP. Make : SKF/NBC/ TATA/FAG/ UBC.

Dismantling, opening and reassembling of CI impellar and transportation to workshop and back after repair and refixing the same position at site and testing of CI impellar for centrifugal /Monoblock 60 to 100 HP pump set complete all as specified and directed.

Dismantling, opening and reassembling of CI impellar and transportation to workshop and back after repair and refixing the same position at site and testing of CI impellar for centrifugal /Monoblock 40 HP pump set complete all as specified and directed.

CI impellar for centrifugal /Monoblock 20 HP pump set including taking out existing old unserviceable complete all as specified and directed.

CI impellar for centrifugal /Monoblock 15/12.5 HP pump set including taking out existing old unserviceable complete all as specified and directed.

CI impellar for centrifugal /Monoblock 7.5 HP pump set including taking out existing old unserviceable complete all as specified and directed.

CI impellar for centrifugal /Monoblock 5 HP pump set including taking out existing old unserviceable complete all as specified and directed.

Power Contactor for following capacity, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable Power contactor and cleaning of carbon fixed as in repair complete all as specified and directed.

Power Contactor for 20 HP Motor Starter. Make: Havells/L&T/C&S

Power Contactor for 40 HP Motor Starter. Make: Havells/L&T/C&S

Power Contactor for 60 HP Motor Starter. Make: Havells/L&T/C&S

Power Contactor for 75 HP Motor Starter. Make: Havells/L&T/C&S

Power Contactor for 100 HP Motor Starter. Make: Havells/L&T/C&S

Motor starter overload relay for following capacity, Motor Starter (Amp rating as per site) including removing of exiting burnt/US relay fixed as in repair complete all as specified and directed.

Motor starter overload relay for capacity 100 HP Motor Starter. Make: Havells/L&T/C&S

Motor starter overload relay for capacity 75/60 HP Motor Starter. Make: Havells/L&T/BCH

Motor starter overload relay for capacity 40 HP Motor Starter. Make: Havells/L&T/BCH

Motor starter overload relay for capacity 20 HP Motor Starter. Make: Havells/L&T/BCH

Supply and fixing in repair/replacement of following parts for existing submerisble pump set 15 HP to 30 HP, electric driven, Three phase, 415 volt complete all as specified and directed.

Thrust Bearing of suitable size motor as per site requirement.

Thrust plate with key of suitable size motor as per site requirement.

Thrust Bearing housing/bearing bush of suitable size motor as per site requirement.

Rotor Sleeve SS (Upper and Lower)/Sand Gaurd of SS of suitable size motor set as per site requirement

Motor Pump coupling SS including Key for suitable size motor as per site requirement

Brass impeller for 8 stage pump upto 5 HP to 15 HP

Brass impeller for 8 stage pump above 15 upto 30 HP

Body bush for capacity 15 HP to 30 HP pump set

For 12.5 HP motor. Make : BCH/C&S/Havells/Legrand/L&T.

For 20 HP motor. Make : BCH/C&S/Havells/Legrand/L&T.

For 25 HP motor. Make : BCH/C&S/Havells/Legrand/L&T.

For 30 HP motor. Make : BCH/C&S/Havells/Legrand/L&T.

For 40 HP motor. Make : BCH/C&S/Havells/Legrand/L&T.

DOL starter with wide band coil, Phase reversal preventation, Phase imbalance preventation, single phase protection, Auto/Manual mode of following capacity including dismantling & taking out old unserviceable DOL starter including dismantling & taking out old unserviceable starter complete all as specified and directed. Make : BCH/C&S/Havells /Legrand/L&T.

For upto 5 HP motor

For above 5 HP to 15 HP motor

Oiling and greasing of pump motor parts (any make any size any type) by means of greasing gun or manually by unbolting and separating the pump motor set at pump house inside defence area complete for smooth operation of machinery including replacement of nut, bolts, washers of appropriate size as per site requirement and motor pump size complete making it leakage free and applying gland packing of necessary quantity and thickness and making working complete noise and leakage free and refixing in same original position complete all as specified and directed. Note: Rates for greese, lubricating oil and gland packing deemed to be included in quoted rates by the tenderer. Also, measurment of these items will be saperate and not to be included in any other item above

Electronic type Single Phase Preventor suitable for 3 Phase, 415 Volt, motor VSP-3 of any make and any size complete as per sample including disconnecting & taking down old unserviceable Single Phase Preventor, complete all as specified and directed. Make : C&S/Havells/ABB/L&T

Pre Stressed concrete Pole 9.00 mtr long, 102mm x 172mm at top and 102mm x 279mm at bottom, class 10 complying with requirements of IS-1678-1978 including painting of poles with two coats of synthetic enamel paint over a coat of primer with black and white strips 30cm wide each upto 1.5mtr height from top of PCC foundation block and numbering of poles, including Excavation and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removal and including PCC 1:3:6, type C1 using 20mm graded crushed stone aggregate as in coping, foundation of poles/struts etc including necessary form work and including disconnecting & taking down old unserviceable broken RCC Pole complete all as specified and directed.

Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one coat primer, one under coat and one finishing coat of synthetic enamel paint including disconnecting & taking down old unserviceable complete all as specified and directed.

Preparation of existing old painted surface of any description such as Panels at any height and painted inside and outside (strictly existing shade) complete after scratching existing rusted surface then applying one coat of primer (superior quality) and synthetic enamel paint in blue colour all around the panels and plinth complete all as specified and directed.

Demolishing old existing broken Earth pit chamber and prepare new Earth pit chamber as per siter requirement and including putting CI cover complete all as specified and directed. Note: Contractor shall be responsible for removing debris of old PCC chamber from site.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 95 sqmm 3.5 core laid in trenches /ducts, through pipe, under floors or roads/along poles etc including dismantling & taking out old unserviceable cable complete all as specified.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 3.5 core laid in trenches /ducts, through pipe, under floors or roads/along poles etc including dismantling & taking out old unserviceable cable complete all as specified.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 35 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking down old unserviceable cable complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking down old unserviceable cable complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 4 core laid in trenches /ducts, through pipe, under floors or roads/along poles including taking down old unserviceable cable complete all as specified and directed. Note for serial item No. 25 to 29 :- Sand cushioning, cable protection cover & excavation / earth work shall be measured & paid for seperately.

Dry sand (Local Tibba sand) to underground cable provided with a layer of 8cm deep before laying cable and 15cm after laying of cable and punned to 18cm after laying of cable and cover for protection of underground cable complete all as specified and directed. Notes:- (i) Approved local tibba dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment only punned thickness shall be measured.

Stone patti 40 to 50 mm thick rough dressed Jodhpur stone slab cover in trenches for protection of cable 25 to 35cm wide and not less than 80 cm in length laid dry abutting each other with gap between adjacent slab not exceeding 10mm over sand cushioning complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing complete all as specified and directed. Note:- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

Galvanized steel water tubing medium grade of 25mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing complete all as specified and directed. Note:- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

Galvanized steel water tubing medium grade of 40mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing complete all as specified and directed. Note:- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

Galvanized steel water tubing medium grade of 50mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing complete all as specified and directed. Note:- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

Galvanized steel water tubing medium grade of 80mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing complete all as specified and directed. Note:- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc or for laying of cables, pipes etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified.

Cable of size 10 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper screen protected 1100 Volts grade submersible flat cable fixed to column pipes/panel to motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed.

Cable of size 16 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper screen protected 1100 Volts grade submersible flat cable fixed to column pipes/panel to motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed.

Cable of size 35 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper screen protected 1100 Volts grade submersible flat cable fixed to column pipes/panel to motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed.

Cable of size 2.50 sqmm (nominal area), copper conductor, PVC insulated, sheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade (ISI marked) cables, drawn through existing conduit fixed on surfaces of wall/ceiling complete including disconnecting & taking out carefully old unserviceable sub main wiring from existing serviceable conduit complete all as specified and directed. Note: Two run for Phase and Neutral of 2.50 sqmm cable shall be measured as one run length for payment purpose.

LED flood lights of capacity 100 Watt, complete with all fittings and fixtures including disconnecting & taking out carefully old unserviceable complete all as specified and directed. Make : Havells Cat Part No. JETAIRISFLS100W LED757ASYMLTG or equivalent of Bajaj/ Philips.

Aluminium conductor, steel reinforced (ACSR) of any size, any type, as per existing one and stringing properly on the insulators and binding with aluminium wire, connectors, Jumpers etc including disconnecting & taking down old unserviceable complete all as specified and directed.

Disc type insulator, porcelain, vitreous 145mm high 255mm dia ball and socket type, white/brown/green, 11000 volt grade, single disc assembly for tension with tension clamp for conductor working pressure 11000 volt grade as in repair/replacement complete all as specified and directed. Make : Jaipuria Brothers/BHEL or equivalent.

Pin type insulator porcelain vitreous, white, brown or green for working pressure 1100 volts, 100mm height and 65mm dia including galvanized mild steel spindle, two Nos GI washers, one No GI nut, fixed as in repair/ replacement complete all as specified and directed.

Pin type insulator porcelain vitreous, white, brown or green for working pressure 11000 volts, 150mm height and 150mm dia including galvanized mild steel spindle, two Nos GI washers, one No GI nut, fixed as in repairs, complete, all as specified and directed.

Air break switch gang operated triple pole mechnically operated, mounted on insulator and steel frame, with (Verticle/Horizontal) operating mechanisum worked from ground level for current rating upto 200 Amps, 11000 volts, complete and testing on load, including taking down old unserviceable complete all as specified and directed. Make : Jaipuria Brothers/BHEL or equivalent.

Air break (switch) insulator (DO assembly) for current rating upto 200 Amps, 11000 Volts complete and testing on load including taking down old unserviceable complete all as specified and directed.. Make : Jaipuria Brothers/BHEL or equivalent.

Topping up/replacement of transformer oil of transformer chamber and conservator with new transformer oil upto a required level of 50 KVA di-electric strength to withstand for one minute in any type and capacity of transformer complete all as specified and directed. Make: Power by Apar or equivalent

Trimming of branches of tree any size and any length coming in contact with conductor and GOD/two pole structure area complete all as directed. Note:- Trimming of branches of tree any numbers of conductor shall be measured one run for payment purpose.

Danger notice plate of 25x20cm size, 1.6mm thick mild steel sheet, vitreous enameled white, with letters, figures and conventional skull and bones in signal red colour for HT 11000 Volts and fixed with MS clamps, bolts and nuts of approved size including taking down old unserviceable complete all as specified and directed.

MCCB, 4 Pole, 400 Amps rating, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

MCCB, 4 Pole, 250 Amps rating, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

MCCB, 4 Pole, 160 Amps rating, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

MCCB, 4 Pole, 125 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

MCCB, 4 Pole, 100 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

MCB Triple Pole with Neutral with overlaod and short circuit protection 'C' Series, 63 Amps rating, rupturing capacity 10 kA, 415 Volts, AC supply, 50 Hz, including disconnecting & taking down old unserviceable MCB, complete all as specified and directed.

MCB Single Pole with Neutral with overlaod and short circuit protection 'C' Series, 40 Amps rating, rupturing capacity 10 kA, 415 Volts, AC supply, 50 Hz, including disconnecting & taking down old unserviceable MCB, complete all as specified and directed.

MCB Single Pole with overlaod and short circuit protection 'C' Series, 40 Amps rating, rupturing capacity 10 kA, 415 Volts, AC supply, 50 Hz, including disconnecting & taking down old unserviceable MCB, complete all as specified and directed.

Cable jointing kit for 11000 Volts grade HT cable for straight through heat shrink type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 50 sqmm 3 core to 95 sqmm 3 core and including dismantling & taking out old unserviceable jointing kit complete all as specified & directed

Cable jointing kit for 11000 Volts grade HT cable for out door termination end heat shrink type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 95 sqmm 3 core to 120 sqmm 3 core and including dismantling & taking out old unserviceable jointing kit complete all as specified & directed

Cable jointing kit for 11000 Volts grade HT cable for indoor termination end heat shrink type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 95 sqmm 3 core to 120 sqmm 3 core and including dismantling & taking out old unserviceable jointing kit complete all as specified & directed

Earthing complete with galvanized steel earth plate electrode 60cmx60cm x6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/ panel/ equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 23 mm thick sand stone slab pit cover complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

Earthing complete with galvanished earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 deep below normal ground level and connected to galvanished iron earth lead strip 25mmx4mm upto 7.50 metre, by means of GI nuts, bolt, check nuts, washers, thimbles, etc as shown in electrical plate No 03 SSR Part-I and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exceeding 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe light grade 20mm bore for watering and 40mm bore GI pipe medium grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers 75mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc including dismantling & taking out old existing unserviceable earthing complete all as specified. Note:- PCC chamber shall be constructed at least 1.5m away from the earth electrode. The pipe for watering shall be provided in slanting manner.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron wire including disconnecting & taking out old existing unserviceable complete all as specified. Note : Nut, bolt and other items included in quoted rate by the tenderer.)

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 x 4mm strip galvanised iron including disconnecting & taking out old existing unserviceable complete all as specified. Note : Nut, bolt and other items included in quoted rate by the tenderer.)

Test point terminal block Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos, 8mm dia, 25mm long hexaguanal head screw including disconnecting & taking out old existing unserviceable complete all as specified.

65mm bore GI heavy grade column pipe in 6 metre length with GI flange on each end, screwed and welded (Not less than 12mm thick) with four Nos MS flat of size 12x6mm supports (10mm long each) on each flange with suitable slot/groove for submersible cable, including bolts, nuts, washer & rubber packing for flanged joints of pipes, including disconnecting & taking out old existing unserviceable complete all as specified and directed.

50mm bore GI heavy grade column pipe in 6 metre length with GI flange on each end, screwed and welded (Not less than 12mm thick) with four Nos MS flat of size 12x6mm supports (10mm long each) on each flange with suitable slot/groove for submersible cable, including bolts, nuts, washer & rubber packing for flanged joints of pipes, including disconnecting & taking out old existing unserviceable complete all as specified and directed.

10mm thick gland packing in small packets for valves and motor pumps fixed as in repair complete all as specified & directed.

12mm thick gland packing in small packets for valves and motor pumps fixed as in repair complete all as specified & directed.

15mm thick gland packing in small packets for valves and motor pumps fixed as in repair complete all as specified & directed.

20mm thick gland packing in small packets for valves and motor pumps fixed as in repair complete all as specified & directed.

Cuttings grass/herbs near installation, plant and sumps complete cleaning of installation, valve chamber and cleaning of installation including necessary tools and safety measures where ever required complete all as specified and directed.

CI reflex valve/Non return valve (NRV) of size 200mm bore, cast iron body, (ISI marked) with confirming to IS 5312 (Part-1) : 2004, heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint including dismantling & taking out old unserviceable non return valve complete all as specified and as directed.

CI reflex valve/Non return valve (NRV) of size 150mm bore, cast iron body, (ISI marked) with confirming to IS 5312 (Part-1) : 2004, heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint including dismantling & taking out old unserviceable non return valve complete all as specified and as directed.

CI reflex valve/Non return valve (NRV) of size 100mm bore, cast iron body, (ISI marked) with confirming to IS 5312 (Part-1) : 2004, heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint including dismantling & taking out old unserviceable non return valve complete all as specified and as directed.

CI reflex valve/Non return valve (NRV) of size 80mm bore, cast iron body, (ISI marked) with confirming to IS 5312 (Part-1) : 2004, heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint and including dismantling & taking out old unserviceable non return valve complete all as specified and as directed.

Cast Iron/Gun Metal foot valve of size 50mm bore (ISI marked) flanged end/threaded type (heavey grade) with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Cast Iron/Gun Metal foot valve of size 80mm bore (ISI marked) flanged end/threaded type (heavey grade) with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Cast Iron/Gun Metal foot valve of size 100mm bore (ISI marked) flanged end/threaded type (heavey grade) with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Cast Iron/Gun Metal foot valve of size 150mm bore (ISI marked) flanged end/threaded type (heavey grade) with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Testing of Sewage Water {(Stilling chamber (Inlet)} and Treated Water (Outlet) sample at authorised government laboratory for biological fitness of water (pH Value, total Suspended Solids, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), total Residual Chlorine, total Coliform) on quaterly basis including glass bottle for collection of sample complete all as specified.

Supply and provide (Calcium hypo chloride) 65%-70% chlorine including anti corrosive agent content Liquid desinfectant for Sewage treatment plants much more stable than chlorine gas & stronger than bleaching powder and sodium hypo chloride packed in 50 Kg drum complete as directed by Engineer-in-Charge. Make : Vasu, Corrocil-D-2000 or equivalent of Auafit/ Altoch(declibec) or Equivalent. Note: Test Certificate from government certified lab for each batch of chlorine to be submited at the time of delivery.

Maintenance and servicing of DG Set capacity 63 KVA complete including draining out of Diesel from tank, cleaning the tank thouroughly and refilling the drained out diesel, draining out engine oil from the chamber, cleaning the chamber thoroughly and refilling the same with new engine oil to required level, replacing the fuel filter, lubricating oil filter, check & clean Air cleaner. change air cleaner elements, check collant level & make up the same, drain the Fuel Filter & water separator, filling the starting batteries with electrolyte/ distilled dwater to maintain the required specific gravity, replace the unserviceable brass connectors for batteries, cleaning of battery terminals & applying petroleum jelly to battery terminal posts & brass connectors, changing of V-Belts, changes rubber hoses and clips of air cleaner, checking of exhaust leakage & repairing the same, Governor, breathers etc, adjust/ set the same for proper functioning of DG Set, checking of fuel, oil and water/ Coolant level etc,adjusting and keeping the fan belts to the desired tension, tightening all the bolts and nuts to the required torque etc, cleaning the DG set with accessories as prescribed by the manufacturer and test for satisfactory running of DG Set for two hour at connected load & record shall be made in respect of RPM, oil pressure, oil temperature, coolant temperature, voltage, frequency, load current, battery charging, fuel consumption etc complete all as specified and directed.

Maintenance & servicing of DG Set capacity 100 KVA to 160 KVA complete including draining out of Diesel from Tank, cleaning the tank thouroughly and refilling the drained out diesel, draining out engine oil from the chamber, cleaning the chamber thoroughly and refilling the same with new engine oil to required level, replacing the fuel filter, lubricating oil filter, check & clean Air cleaner. change air cleaner elements, check collant level & make up the same, drain the Fuel Filter & water separator, filling the starting batteries with electrolyte/ distilled water to maintain the required specific gravity, replace the unserviceable brass connectors for batteries, cleaning of battery terminals & applying petroleum jelly to battery terminal posts & brass connectors, changing of V-Belts, changes rubber hoses and clips of air cleaner, checking of exhaust leakage & repairing the same, Governor, breathers etc, adjust/ set the same for proper functioning of DG Set, checking of fuel, oil and water/ Coolant level etc, adjusting and keeping the fan belts to the desired tension, tightening all the bolts and nuts to the required torque etc, cleaning the DG set with accessories as prescribed by the manufacturer and test for satisfactory running of DG Set for two hour at connected load & record shall be made in respect of RPM, oil pressure, oil temperature, coolant temperature, voltage, frequency, load current, battery charging, fuel consumption etc complete all as specified and directed.

Distilled water best quality suitable for lead acid battery complete all as specified and directed.

1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including dismentling & taking down old unserviceable water tank capacity 1000 litre complete as specified in SSR Part-I.

500 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including dismentling & taking down old unserviceable water tank capacity 500 litre complete as specified in SSR Part-I.

Cleaning of following Sewage Treatment Plant Chambers by professional agency after De-watering of sewage and cleaning with Jet Pressure Water Pump for dirt, silt and agae, scrapping with steel brushes/ hessin cloths of the chamber walls from inside including floor of the chamber and apply solution of Potassium Permanganate (KMnO4) complete and providing two coats of anti corrosive paint including watering etc and repair to vent pipes including providing wire mesh and clamps complete all as specified and directed by Engineer-in-Charge. Note: If work is not done upto satisfaction level of concerned JE/AGE (E/M), the work will be redone upto the required level without any extra cost. Necessary tools and safety measures for man power to be arranged by contractor.

Stilling Chamber of size 1.40 x 1.40 x 1.40 m.

Pumping Station Plant at Central Sewage Treatment Plant.

Grit Chamber of size 3.6MX1.2MX1.1 M

Equalization Tank of size 8.30 M (Dia) x 3.50 M

Moving Bed Bio Reactor of size 4.00 M (Dia) x 5.00 M

Tube Settler of size 7.00 M x 6.50 M x 2.70 M

Chlorine Contact Tank of size 7.00 M x 4.50 M x 2.00 M

Sludge Holding Tank of size 8.10 M (Dia) x 2.50 M

Treated Water Tank of size 13.50 (Dia) x 6.00 M

Sewage Pump Stations

Pebbles, gravels, Silex (Silica) and sand of following sizes for Dual Media Filter of Sewage Treatment Plant, premixed for filling into vessel and cleaning the around area and repacking the vessel after filling in new items complete by means of packing and fixing material including labour and testing for appropriate pressure complete all as specified and directed

Pebbles of size 40-20mm

Pebbles of size 20-12mm

Pebbles of size 12-6mm

Pebbles of size 10-3mm

Crushed Gravel of size 6-3mm

Fine Sand of size 16/32

Coarse Silex (Silica)

Fine Silex (Silica)

Activated Granular Carbon for filling into Activated Carbon Filter of Sewage Treatment Plant including draining out the existing used Charcoal from Filter vessel and cleaning the around area and repacking the vessel after filling in new items complete by means of packing and fixing material including labour and testing for appropriate pressure including taking down old carbon filter complete all as specified and directed.

Bourdon type glyserin filled pressure gauge (150mm dia) complete with siphon tubewith isolating cock having range of 0 to 7Kg/Cm2 as per IS 8793 complete all as specified and directed. Make : H Guru Model No. 6PSSSW2 or equivalent as approved by GE.

Tube Deck Media of size 100mm/150mm X 750mm/1000mm (as per sample) for Tube Settler Chamber as per sample complete all as specifie and directed.

MBBR Media Virgin PP UV stablilized based media with size of 16x22mm/ 17x24mm with removal performace of 30 BOD complete all as specified and directed.

Chlorine Dozing pump 0-6 LPH with flow of 4 KG/CM2 with all fittings and fixtures complete all as specified and directed. Make : Aventura Model No- Micro V.1.4 or equivalent.

Servicing of blower of capacity 760 Cum/Hour with pressure 0.65 Kg/SqCM of RPM 1000, including replacement of Paper filter of blower of Make : Everest Model M-710 complete all as specified and directed. Note : All necessary Tools & Plants required for servicing to be included in quoted rates.

Servicing of Decanter Centrifuge including greasing of Bearing at Feed/ Slurry end and Main Bearing at Liquid discharge, Cleaning of Scroll/ Conveyor, Bowl, Pump blades complete by authorised OEM manufacturer of Make : Alfa Laval. Note : All necessary Tools & Plants required for servicing to be included in quoted rates.

V Belt, Heat and Oil resistant of Model SP13, 2150 complete all as specified and directed. MAKE : FENNER or equivalent.

Cable of size 6 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper 1100 Volts grade submersible flat cable fixed to column pipes/panel to motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed.

Cable of size 25 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper 1100 Volts grade submersible flat cable fixed to column pipes/panel to motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed.

Opening and reassembling of Non clog submersible motor (STP motor) after rewinding and replacement of worn out spare parts including taking out the burnt winding wire and rewinding of submersible motor following capacity with new PVC insulated solid copper conductor (wire) superior quality of approved make, gauge/size & number of wire as per existing including insulation material and for suitable RPM including rotor balancing, minor spares, fixing new mechanical seal for avoiding of shorting of motor and replacement of unserviceable spare parts and reassembling the components & testing for function ability including taking old unserviceable motor from treated water tank complete all as specified and directed. Note: The Job include the opening of motor at site for damaging of existing stator winding if found burnt/damaged in front of concerned JE/AGE (E/M) after testing on site before taking to work shop outside MD land. Motors will be given for repairing as per the site condition and need for repair being maintenance work.

Submersible motor of capacity 25 HP, 3 phase, 415 volts

Submersible motor of capacity 10 HP, 3 phase, 415 volts

Submersible motor of capacity 7.5 HP, 3 phase, 415 volts

Submersible motor of capacity 3.0 HP, 3 phase, 415 volts

Opening and reassembling of STP monoblock /centrifugal pump (motor) after rewinding and replacement of worn out spare parts including taking out the burnt winding wire and rewinding of monoblock/ centrifugal pump (motor) following capacity, Three Phase, 415 volts with new PVC insulated solid copper conductor (wire) superior quality of approved make, size & number of wire as per existing including insulation material, minor spares and replacement of unserviceable spare parts and reassembling the components & testing for function ability, complete, all as specified & directed. Note: (i) The include opening of motor at site for damaging of existing stator winding if found burnt/damaged in front of concerned JE/AGE (E/M) after testing on site before taking to work shop outside MD land and testing of RPM to be done after installation on Ground after rewinding. Motor will be given for repairing as per the site condition and need for repair being maintenance work. (ii) Unit rate (quoted by the tenderer) shall be deemed to included for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Monoblock/Centrifugal motor of capacity 40 HP, 3 phase, 415 volts

Monoblock/Centrifugal motor of capacity 12.50 HP, 3 phase, 415 volts

Monoblock/Centrifugal motor of capacity 7.50 HP, 3 phase, 415 volts

Monoblock/Centrifugal motor of capacity 5 HP, 3 phase, 415 Volt,

Monoblock/Centrifugal motor of capacity 1.50/2.0 HP, 3 phase, 415 volts

Deep Groove ball/roller bearing (Double sealed ball bearing) for the following capacity of STP Pump (Primary and secondary) complete all as specified and directed. Make : SKF/NBC/TATA/FAG/UBC. Note: The rates include cost of two nos bearing as per pump design. Both the bearings(as per pump make) to be replaced at the same time.

Centrifugal pump/mono block pump set of capacity 40 HP

Centrifugal pump/mono block pump set of capacity 12.5 HP

Centrifugal pump/mono block pump set of capacity 7.5 HP

Centrifugal pump/mono block pump set of capacity 5.0 HP

Centrifugal pump/mono block pump set of capacity 1.5/2.0 HP

Centrifugal/Monoblock STP Pump motor MS coupling capacity 40 HP motor (Beam, Jaw, Gear any type) including taking down old unserviceable complete all as specified and directed.

Centrifugal/Monoblock STP Pump motor MS coupling capacity 12.5 HP motor (Beam, Jaw, Gear any type) including taking down old unserviceable complete all as specified and directed.

Centrifugal/Monoblock STP Pump motor MS coupling capacity 7.5/5.0 HP motor (Beam, Jaw, Gear any type) including taking down old unserviceable complete all as specified and directed.

Centrifugal/Monoblock STP Pump motor MS coupling capacity 1.5/2.0 HP motor (Beam, Jaw, Gear any type) including taking down old unserviceable complete all as specified and directed.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 40 HP motor for STP (Primary and secondary) complete all as specified and directed. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 12.5 HP motor for STP (Primary and secondary) complete all as specified and directed. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 7.5/5.0 HP motor for STP (Primary and secondary) complete all as specified and directed. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

Contactor for STP motor capacity 40 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed.

Contactor for STP motor capacity 12.5 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed.

Contactor for STP motor capacity 7.5 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed.

Motor starter relay for STP motor capacity 40 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/ unserviceable relay complete all as specified and directed

Motor starter relay for STP motor capacity 12.5 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/ unserviceable relay complete all as specified and directed

Motor starter relay for STP motor capacity 7.5 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/ unserviceable relay complete all as specified and directed

MCCB 4 Pole, 200 Amps rating, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, thermal and adjustable making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

Cast iron body sluice valve heavy duty class ‘PN-1.6’, 80mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve, complete all as specified & directed.

Cast iron body sluice valve heavy duty class ‘PN-1.6’, 100mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve, complete all as specified & directed.

Cast iron body sluice valve heavy duty class ‘PN-1.6’, 150mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve, complete all as specified & directed.

Cast iron body sluice valve heavy duty class ‘PN-1.6’, 200mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve, complete all as specified & directed.

Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 40mm bore or brass ferrule and fixed including dismantling & taking out old unserviceable valve complete all as specified & directed.

Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 65mm bore or brass ferrule and fixed including dismantling & taking out old unserviceable valve complete all as specified & directed.

Cast iron body butter fly valve heavy duty, 100mm bore, ISI marked with confirming to IS, both flanged ends and drilled, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 100mm bore, complete all as specified & directed.

Cast iron body butter fly valve heavy duty, 150mm bore, ISI marked with confirming to IS, both flanged ends and drilled, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 150mm bore, complete all as specified & directed.

PVC cable, 2.5 sqmm, 2 core, nominal area of copper conductor, insulated and (Flame Retardant) FR PVC round sheathed, Copper Conductor (flexible) industrial cable, 1100 Volt grade, conforming to IS 694 including taking down old unserviceable cable complete all as specified and directed. (Note :- Two run for Phase and Neutral shall be treated at One run).

LED street light 90 Watt made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP 66 protection and impact resistance of IK07 including taking down old unserviceable LED street light complete all as specified and directed.

Supply, laying, jointing, commissioning & testing DI pipes with rubber gasket Tyton Joints of spigot and socket ends centrifugally cast (spun) class "K-7" conforming to IS-8329 -2000 in any length of size 150mm bore laid in trenches ncluding taking up or down old unserviceable CI/DI water tubing and connections of 150mm bore complete all as specified and directed.

Supply and Fixing CI/DI fitting upto 150mm bore pipe line for reducing/bends (any type radius and angle) tapers any type, staright, bend, increasing, decreasing or double socket extra Tee pieces single branch Ý'Junction, double branch, cross collars caps etc complete all as specified and as directed.

Supply, laying and joing (By butt fusion welding method) in standard length BIS marked (high density polyethylene Pipe) HDPE pipe suitable for potable water as per IS specification No 4984/1995 (Pressure rating 6 Kg/Cm2 PE-100) and fittings (specials suitable to HDPE pipes) including taking down old unserviceable pipe complete all as specified and directed.

25mm nominal dia HDPE Pipe (Outer Dia)

40mm nominal dia HDPE Pipe (Outer Dia)

63mm nominal dia HDPE Pipe (Outer Dia)

90mm nominal dia HDPE Pipe (Outer Dia)

125mm nominal dia HDPE Pipe (Outer Dia)

160mm nominal dia HDPE Pipe (Outer Dia)

180mm nominal dia HDPE Pipe (Outer Dia)

Rectification of Leakages by necessary excavation (upto one length of 6.00 RM) in any type of soil, in any situation/depth including bailing out leakage water by suitable measures, repair to DI/CI/ HDPE of following sizes pipe with MS clamp including rubber cushioning, 3mm thick and 300mm wide with hole drilled for nutbolts including suitable nuts and bolts for rectification of leakages complete all as specified and directed. Note: Cost of JCB for lifting of pipe for repair will be part of quoted rates.

40mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

63mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

90mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

125mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

160mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

180mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

Unloring the Non clog submersible pump of any capacity and removing dirt, waste from it and clean it and making it serviceable complete all as specified and directed.