ADDN/ALTN OF DINING HALL AND ENTRY OF P-4 NCC OFFICER MESS, SPECIAL REPAIRS TO BOUNDARY WALL OF CONNAUGHT BARRACK (P-7) AND BLDG NO P-20 UNDER GE (W) COLABA, MUMBAI

Amount

Excavation over areas not exc 1.50m deep and getting out in hard dense soil all as specified and directed.

Excavation in trenches nexc 1.5 m wide and nexc 1.5 m in depth and getting out in any type of soil all as specified and directed.

M&L Moorum/red bajri filling under floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as spcified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed.

M&L PCC 1:4:8 type, D-2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete all as specified & directed.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete all as specified and directed.

M&L RCC M-25 grade Design mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns all as specified and directed.

Use & waste formwork to sides and soffits of floor or roof beams, beam haunch- ings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams for rough finished surfaces of concrete all as specified and directed.

M&L RCC M-25 grade Design mix as in lintel band / RCC coping over 1.50m span all as specifed and directed.

Use & waste formwork to square/ractangular sides of pillars, posts, struts, piers, columns, and stanchions rough finished surfaces of concrete all as specified and directed

M&L RCC M-25 grade Design mix as in Columns, pillars, piers, posts and struts all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No 14 above but 5 to 10 mm dia in stirrups, spacers and binders

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar CM (1:4) type B1, 1:2:4 (using 20mm graded crushed aggregate) all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work in CM 1:4, finished surfaces even and fair without using extra cement all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work in CM 1:4, finished surfaces even and fair without using extra cement all as specified and directed.

M&L rendering 10 mm thick on fair faces of concrete surfaces in CM 1:4, finished surfaces even and fair without using extra cement all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point in soils all as specified and directed.

PVC (SWR) pipes 110mm dia, Single socketed, in any length laid in trenches or in floors, weep holes all as specified and directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer for new seel surfaces including preparation exc 10cm width or girth all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) all as specified and directed.

S&F Concertina coil with punched tape of 600mm dia centre core wire shall be minimum 2.5mm dia of mild steel wire confirming to IS 280-2006. Galvanised coating of steel concertina coil shall confirm to the requirements as laid down for medium coated wire in IS 4826 "Hot dipped galvanised coating of round steel wires" concertina coil shall be fixed in dimond shape with the help of dovetail to handle and spikes shall be fixed at both end of coil, minimum staight length of the wire 150 RM of 10 RM of work, minimum weight 13.5 Kg for 10 RM of work i.e 90 gm/RM of wire all as specified and directed.

M&L PCC 1:2:4 type B0, (using 12.5 mm graded crushed stone aggregate) as in coping/cills including necessary form work, weathering, slightly rounded or chamfered angles and throating all as specified and directed.

M&L PCC 1:2:4 type B0, (using 12.5 mm graded crushed stone aggregate) as in coping/cills including necessary form work weathering, slightly rounded or chamfered angles and throating all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M&L mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming to Fe 410- W (Gde -E -250 quality A) all as specified and directed.

S&F coloured Glazed earthen ware tiles 200mmx 100mm x 6mm thick, in vertical surface, including 10mm thick plaster in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing shade of tiles all as specified and directed.

S&F in repairs cast iron arrow, tee, bends and designs of varoius pattern as per requirement of site for gates, rails, braces, etc., complete, drilled for fixing of hooks and hinges or steel hanging door fittings also fastening, welding and fixing complete including dismantling/ taking down old existing all as specified & directed.

M&L in repairs for SS 304 grade stainless steel tubing (Square/Round/Rectangular) of suitable gauge as in SS guard bars, railings, SS frame works including all fixing arrangments, including taking down of old SS guard railing all as specified and directed.

Demolition of cement concrete in ground floor & paving n. exc 15 cm thick (below or above GL) unreinforced all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons, etc. laid, bedded and pointed in any mortar and removal of rubbish off the site all as specified and directed.

M&L PCC 1:4:8, type D-2, (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete all as specified and directed.

M&L PCC in roof kerbs or mud stops, rounded or chamfered on edges 1:2:4, type B1 (using 20mm graded crushed stone aggregate) all as specified and directed.

M&L PCC 1:3:6, type C-2, (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete all as specified and directed.

M&L crushed stone sand filling under precast interlocking paver blocks and all other similar works all as specified and directed.

M&L rubber moulded glossy finished precast concrete interlocking paver block of any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-35 Grade laid over sand cushioning including compaction of paver blocks using surface vibrator all as specified and directed. Note :- Sand cushioning shall be measured and paid separately under relevant item.

M&L Granite (of any type and colour) 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid in floors/Jambs/WHB conters and all other similar works in approved design laid over 20 mm thick screed bed in CM 1:4 all as specified and directed.

M&L heavy duty external floor tiles 15-16 mm thick of size 600x600 mm of matt finish, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles laid over 15 mm thick screed bed in CM 1:6 all as specified and directed.

Dismantling of wall and ceiling boards( fibre pulp insulation etc) any thickness including cover fillets all as specifed and directed.

Taking down door Chowkhats and shutters of windows/ventilators with wire mesh / glass and MS grills of any size including all fittings and fixtures all as specified and directed.

Demolition of cement concrete (unreinforced) below or above ground level n.exc 15cm thick and removing rubbish to a distance n.exc 50m at low lying area all as specified and directed

S&F SS 304 Grade metal letters of height 200mm with PU paint to match the logo colours, mirror polish finish, anti rust and including necesssary arrangements to fixing in walls, using scaffolding at any height all as specified and directed.

M&L brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and directed.

M&L broken stone or boulders of hard core of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface using power roller all as specified and directed by Engr-in-charge.

M&L 100 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in flooring all as specified and directed.

M&L earth filling in floors, spreading and leveling in layers, well ramming including watering as required all as specified and directed.

M&L in repairs coloured double charged polished glazed vitrified tiles 10 mm thick (Square/rectangular) polished, area of each tile exc 0.36 sqm but not exec 0.64 sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed.

M&L in repairs coloured double charged digital glazed vitrified tiles 10 mm thick (Square/rectangular) polished, area of each tile exc 0.36 sqm but not exc 0.64 sqm in vertical surfaces, such as skirting & dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed.

S&F in repairs 25 mm dia stainless steel decorative type curtain rods and all other connected works all as specified and directed.

S&F in repairs 25 mm dia stainless steel decorative type curtain Brackets, including fixing in position and all other connected works all as specified and directed.

S&F 18-19 mm thick HDH board, prelaminated one side with decorative choice lamination & other side high glossy acrylic sheet of 3mm thick, exterior grade, fixed with screws to frame work as in cup borad & kitchen cabinet shutters and all other similar works all as specified and directed.

M&L machine cut, polished cudappah stone work 20 to 25 mm thick (table rubbed and polished) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in kitchen platform, flooring and all other similar works, including laying over 15mm thick cement mortar (1:6) all as specified and directed.

M&L Granite (of any type and colour) 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid in floors/Jambs/WHB conters and all other similar works in approved design laid over 20 mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L in repairs 12 mm thick ready mix plaster in single layer on brick wall or concrete surfaces including making groove of appropriate size, on other than fair faces of concrete/brick surfaces (internal surface) and finished surfaces even & smooth without using extra cement all as specified and directed

M&L preparation of newly plastered wall surfaces and applying a coat of wall care putty (Birla White Wall care or equivalent) 2mm thick ( in two coat 1 mm each ) average on plastered surfaces, rubbing with sand paper, preparatory to distempering and applying two coats of acryilic emulsion over a coat of alkali resistant priming paint all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making, provision for fixing of fittings where ever required including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. Note : (i) Glass panes will be measured & paid separately . (ii) The quoted rate shall be inclusive of cost of rubber beading and glazing clips, hionges, handle. However it will not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

S&F sheet glass, ordinary quality, 5.5 mm thick, plain or frosted on one side and glazed with oil putty or fixed with rubber beading in square exc 0.5 Sqm in each pane all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm of approved design and fixed with aluminium windows all as specified and directed.

S&F in repairs 12mm thick, toughened glass for door shutters, partitions in bathroom or other places, shelves, table top etc. in similar work with and including fitting and fixtures such as glass handles ss studs, fittings for door pivots, spring machine all as specified and directed .

Supply and fixing Sun control film, 50 micron non reflective type, sticked to glass as per manufacturers instructions all as specified and directed.

S&F in repairs SS 202 Stain finish Handle D type, 25mm dia 600mm long for glass shutter all as specified and directed

M&L for GI frame work for seamless ceiling 600x600mm grid size comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre all as specified and directed.

M&L 8 mm thick exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (frame work for ceiling shall be measured and paid separately) fixed to aluminum frame work in ceiling and all other similar works all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat comprising of 100 mm x 65 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum specification as per IS 15931: 2012 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast unserviceable fast/lugs/SS dash fasteners of required dia and length all as specified and directed by Engr-in-Charge.

S&F 35 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, both faces is covered with decorative face Laminate both side with including 5mm thick teakwood lipping all around / frame to match on both side with supply & fixing stainless steel 7.5 inch Mortice 7 lever door lock, double action with handle all as specified & directed.

S&F 100 mm butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 all as specified and directed.

S&F 200mm size brass handle cast type polished bright all as specified and directed.

S&F extruded aluminium alloy barrel tower bolts, st, with bright bolt and fixed of size 200 mm for doors all as specified and directed.

S&F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed all as specified and directed.

M&L Point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volts grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling and including provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green coloured as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators, etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III Note (All chases will be cut by chase cutter only)

S&F switch piano (ISI marked) Single pole 240 volts, 5 Amps all as specified and directed.

S&F LED security Building light fitting 45 Watt, pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light all as specified and directed.

S&F LED Post top 45 watt for gate and landscape lighting with IP 65 Protection to impact and corrosion, anti glare and uniform distribution complete all as specified and directed by Engr-in-Charge

S&F in repairs MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection all as specified and directed.

S&F in repairs MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series all as specified and directed

S&F in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's all as specified and directed.

Excavation in trenches not exc 1.5mtr. in depth and not exc 1.5mtr in width and getting out in soft/ loose soil for laying of cable all as specified and directed.

Returning ,fillling in trenches, spreading, levelling, watering and well ramming in layers not exceeding 25cm thick all as specified and directed.

Removing excavated material/ surplus soil and depositing where directed at a distence not exceeding 50mtr.at a level not exceeding 1.5 mtr from starting point all as specified and directed.

Supply & lay in trenches, crushed stone sand, clean, including spreading, levelling, punning for laying /cushioning of cables all as specified and as directed.

Supply lay in trenches fly ash bricks, old size sub class “B” disignation for cable protection all as specified and directed.

Supply, lay in trenches, floors, fix on wall/pole, passing through pipes LT UG cable , 1100 volts grade, PVC/ XLPE insulated, with multistranded aluminium conductors, armoured with galvanised steel wire or tape, gland, lugs, etc. of size 10 Sq.mm 3 core, confirming to IS specifications all as specified and directed.

S&F on pole / wall or lay in trenches under road / drain crossings for drawing cables, GI pipe 40 mm light grade ISI marked of following sizes including necessery pipe , fittings ,clamps, bolts , nuts etc. all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm c/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing on completion all as shown in Electrical Plate No 3 of SSR part -I.

SAHU AND SAHU CO. (BID ID -3227933)

I.J Enterprises (BID ID -3233046)

N.S.ENTERPRISES (BID ID -3228262)

Shivam Enterprises (BID ID -3231760)

Panther Facilities (BID ID -3233555)

sunenterprises (BID ID -3232911)

GANGAJAL (BID ID -3229862)

Bidder Name

Unitech Enterprises

SAHU AND SAHU CO.

I.J Enterprises

Panther Facilities

GANGAJAL

Shivam Enterprises

N.S.ENTERPRISES

sunenterprises