REPAIR MAINT OF COMPOUND WALL RAZOR WIRE CONCERTINA COIL CHAIN LINK FENCING HARDSTANDING GI SHED AND CHEQUERED TILES AT ZONE B AREA AT GMS UNDER GE I GOS

Amount

Dismantling of AC corrugated / semi corrugated sheet as in roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Excavation in any type of soil for post holes (or similar holes) each not exceeding 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good disturbed surface complete all as specified and directed.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floor and paving exc 15cm thick (below or above ground level) complete all as specified and directed.

M&L Hardcore of broken stone or boulder of guage n.exc 63 mm, deposited, spreed and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 using 40 mm graded stone aggregates as in hard standing 100 mm thick laid in panels and finished even and smooth without using extra cement and spike rolling to surfaces or making impression of expanded metal whilst the concrete surface is green complete all as specified and directed.

M & L for 20 mm thick Screed bed or bedding layer of mortar in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L chequered cement concrete tiles 20 cm X 20 cm X 25 mm thick, set , jointed and pointed in neat cement surry in floors with pigments complete all as specified and directed.

M&l for 50 mm thick Sand cushning below interlocking paver tile complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size fixing with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring surface finished even and rough to receive the topping layer complete all as specified and directed.

M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 Sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with 20 mm thick screed bed or bedding layer in cement mortar 1:4, including rubbing and polishing complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate, in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies 35 mm thick (measured solid) including all mouldings but excluding frame in cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregates and set in cement mortar 1:4 complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) embedded in natural ground etc any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Excavation in soft / loose soil for post holes (or similar holes) each not exceeding 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good disturbed surface complete all as specified and directed.

M&L for RCC type B-1, 1:2:4 using 20 mm graded stone aggregate in precast posts, fencing posts, straining or terminal posts, struts etc for fencing average sectional area exc 100 Sq cm but not exc 250 Sq cm with or without chamfered angles and flat, splayed, rounded or mitred tops and fixed complete all as specified and directed.

Mild Steel Fe-410-W Gde E-250 or Fe-290 Gde E-165 round bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F PVC coated chain link fencing 100 x 100 mm mesh size made out of GI wire from 2.5 to 2.85 mm dia having minimum 1mm thick PVC coating over it including inner woven wire.Weight of wire mess not exc 4kg/sqm complete all as specified and directed.

S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but not exc15 cm long and 11 to 15 mm dia of shank complete all as specified and directed.

S&F Galvanized, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of posts, straining bolts,standard bolt, including securing or tying at crossing with and including provision of galvanized mild steel wire staples or steel pins, etc complete all as specified and directed. (Each line of wire to be measured for the purpose of payment).

M&L for preparation of new or previously untreated surfaces of steel of any description, not exc 10cm in width or girth when unconnected with other painting and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coat of white wash complete all as specified and directed.

Demolition of brick work / stone boulder masonry built in cement mortar complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided coping etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/ loose soil complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregates. as in foundation filling maas concrete complete all as specified and directed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Formwork to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Formwork to Square,rectangular or polygonal rough surface of concrete of sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Mild steel TMT bars 8mm dia and over, cut to length, spacers and binders and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Item No.42 above but 5mm dia and over upto and including 10mm dia in stirrups,spacer and binders complete all as specified and directed.

M & L for PCC type B1 1:2:4 (using 20mm graded stone aggregate) as in cills steps, bands plinth courses, copings, apex stone, bed plates kerbs, levelling course etc complete all as specified and directed.

M & L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for MS work as in misc work such as angle iron , flat for frame of fencing post etc incl existing drilling holes bending to shape as required , MS clamps for fixing in and fixed in position incl bolts etc complete all as specified and directed.

S&F Galvanized, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of posts, straining bolts,standard bolt, including securing or tying at crossing with and including provision of galvanized mild steel wire staples or steel pins, etc complete all as specified and directed. (Note : Each line of wire to be measured for the purpose of payment).

Fixing in repairs Restraining and resecuring including making good staples etc Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm barbs at 100mm spacing complete all as specified and directed.

M&l for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old treated surfaces of wall by complete removing of existing treatment and applying two coat of Cement base paint complete all as specified and directed.

Taking down cement plaster on brick or stone etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L 15mm thick rendering on fair faces of brick work (or) concrete surfaces in CM 1:6 and to be finished even & smoth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

Returning filling in including, spreading, levelling watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and smooth without using extra cement to receive the topping layer complete all as specified and directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectagular) dark colour shade polished,area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors over 20mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No 58 above but on vertical surface of wall of size not exceeding 0.36 sqm,as in dado/skitting including 10 mm thick rendering in CM 1:4 complete all as specified and directed

M&L for glazed ceramic coloured tiles in vertical surface 300 x 200 mm x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles including 10mm thick rendering in CM 1 :4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20mm thick screed bed in CM 1 :6 complete all as specified and directed.

All as per itme No 61 above but vertical surfaces area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm as skirting non skid ceramic tiles including 10 mm thick rendering in CM 1:4 complete all as specified and directed

M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 20mm thick screed bed in CM 1 :6 complete all as specified and directed.

All as per itme No 63 above but vertical surfaces area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm as skirting non skid ceramic tiles ncluding 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like 15mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 20-25 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with 15 mm thick screed bed or bedding layer in cement mortar 1:4, including rubbing and polishing complete all as specified and directed.

M&L for preparation of old distempered surfaces of wall including cornices etc and applying one coat of acrylic distemper complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of and applying one coat of cement base paint complete all as specified and directed.

Likitha Enterprises

M/S K MURALIDHARA PATRA

M/s Bapujee Builders and Traders

G.KRISHNA MURTHY AND PARTNERS

M/s Ats Electricals

M/s MAA BHAIRABI ENTERPRISES

c p engineering works