GE/S(U)-08/2021-22 SPL REPAIR OF TWO TOILET BLOCKS AT DRONE BOYS HOSTEL (BLDG NO NP-01 AND NP-04) PROVN OF BATHROOMS AND TOILETS WITH ALLIED INFRA AT PARA SF 02 X WATER POINTS AT INF BN LOCATION AMMUNITION TRG SHED FOR UNIT STAFF AT FD AMN REPAIR SEC

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation & not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Returning, filling including spreading leveling watering and well ramming in layers not exceeding 25 mm in any type of soil complete all as specified and directed.

Removing excavated material (soils) exceeding 250 m but not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Reinforce cement concrete M-25 (20 mm graded aggregates) design mix as in foundations, including rafts, footings, foundation, beams; plinth beams; bases for columns etc. basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Reinforce cement concrete M-25 (20 mm graded aggregates) design mix columns, pillars, piers, posts and struts complete all as specified and directed.

Reinforce cement concrete M-25 (20 mm graded aggregates) design mix as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

Reinforce cement concrete M-25 (20 mm graded aggregates) design mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter for rough flat finished surfaces of concrete complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough flat finished surface of concrete complete all as specified and directed.

Formwork to flat sides and soffits of or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splays between floors and beams complete all as specified and directed.

Formwork to soffits of suspended flat slabs such as roof slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and directed.

Formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in wall, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide complete all as specified and directed.

TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per ser item No 17 above but 5 mm dia and over including 10 mm dia in stirrups, spaces and binders etc. complete all as specified and directed.

10 mm thick on fair faces of brick/concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

15 mm thick rendering in two layers (10 mm + 5 mm) on fair faces of brick/concrete or stone surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete all as specified and directed. (WPC shall be measured separtely).

Supply only liquid water proofing compound complete all as specified and directed.

05 mm thick CM 1:4 rendering on fair surfaces of ceiling work and finished even and smooth without using extra cement complete all as specified and directed.

10 mm thick rendering as backing coat to receive the tiles on fair faces of brick/ concrete surfaces in cement mortar 1:3 and finished even and rough complete all as specified and directed.

Preparation of new plastered surfaces on walls and applying three coats of white wash complete all as specified and directed.

Preparation of new plastered surfaces on ceiling and applying three coats of white wash complete all as specified and directed.

Preparation of new plastered surfaces on walls and applying two coats of cement based paint complete all as specified and directed.

Preparation of new plastered surface and applying two coats of apex ultima paint over a coat of primer including preparation of surfaces complete all as specified and directed. (colour of apex ultima approved by GE/Engr-in-Charge).

Shingle filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed.

75 mm thick cement concrete (1:4:8) type D-2 as sub base to floor complete all as specified and directed.

25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor and finished even and fair complete all as specified and directed.

Non-skid coloured ceramic tiles (square/ rectangular) 7 to 8 mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Glazed ceramic tiles in vertical surface 300 x 450 x 7 mm and 300 x 600 x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface complete all as specified and directed.

Mild steel ventilators (Box type) factory made with top hung shutters and bottom fixed type shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3 (ii) Glazing, wire gauge shall be measured and paid separately.

Framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work confirming to Fe.290.Gde-E-165 quality A including one shop coat of zinc chromate primer paint including preparation of surfaces at contractor's workshop before fabrication complete all as specified and directed.

4 mm thick glass sheet of ordinary quality not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steelwire staples complete all as specified and directed.

Preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing complete all as specified and directed.

Factory made solid panel PVC Moulded door shutter 28 to 30 mm thick stiles with 2, 4 or 6 raised panel design with 2 mm thick Moulded PVC sheet on the front face and 2 mm thick plain coloure PVC sheet on back face complete all as specification and drawing.

Pressed steel frames for doors made out of 1.25 mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12 mm bar thresh hold etc. complete, of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

40 mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Providing cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregates) for filling in the pressed steel door frame/hold fast complete all as specified and directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed.

Mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including cast iron P trap, bore of pipe 100 mm and provision of concrete bedding complete all as specified and directed.

Vitreous china urinals half stall white including CP urinal Spray Nozzal complete including providing and fixing of plug bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and including 60 mm long brass screws pointing including 60 mm long brass complete all as specified and directed.

10 litres Vitreous China valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply only flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.

PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Angle valve, cast copper alloy fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and directed.

Stop valve (concealed type), cast copper alloy fancy type, chromium plated with long shank and cup screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and directed.

15 mm dia bib tap fancy type chomium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Vitreous China wash basin (Pedestal), white, flat back, size 550 mm x 400 mm excluding tap, chain, plug and porcelain stopper but including brackets and cutting for and pinning in ends of brackets complete all as specified and directed.

Pillar taps 15 mm bore fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' and cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

Brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

100 mm dia cast iron sanitary connection pipe upto 300 mm length complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 100 mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 75 mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 50 mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

Cast iron bend (any radius) diminishing pieces or tapers 100 mm bore fitted with oval access door complete all as specified and directed.

Cast iron bend (any radius) diminishing pieces or tapers 75 mm bore fitted with oval access door complete all as specified and directed.

75 mm bore cast iron cowls complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Cast iron floor trap 75 mm, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Stack clamps made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified and directed.

Shower roses 15 mm chromium plated with or without swivel joints, any size, including 125 mm long arm and fixing to steel pipe or union, complete all as specified and directed.

15 mm bore galvanised steel water tubing 15 mm dia medium grade (ISI Marked) with all fittings and fixed complete to wall and or laid under floors etc. complete all as specified and directed.

20 mm bore galvanised steel water tubing 20 mm dia medium grade (ISI Marked) with all fittings and fixed complete to wall and or laid under floors etc. complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20 mm in repair complete all as specified and directed.

1000 ltr capacity rotational moulded polythylene water storage tank (Cylindrical vertical with threaded cap) hoisted and fixed in position all as specified in SSR Part I, including 20 mm bore dia ball valves high pressure of PTMT with epoxy coated aluminiun rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20 mm - 210 grms) complete all as specified and directed. (ISI Marked)

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Extra over stone walling for hammer dressing with miximum depression on face from straight edge held against the dressed surface not exceeding 20 mm to face stones (Granite or Trap stone) and dressing of face beds and joints, as specified of ranom rubble walling, uncoursed or brought upto courses complete all as specified and directed.

PCC 1:2:4 type B-1 (using 20 mm graded aggregate) in surface channel and drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/ stopped ends etc complete all as specified and directed.

20 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

Providing cement concrete 1:2:4 type B-1 (using 20 mm graded aggregate) as in coping raised platform for OHT, water through and the line including weathering, slightly rounded or chamfered angles and throating etc. complete all as specified and directed by Engr-in-Charge.

15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

150 mm bore Reinforced concrete pipes, class NP-2, laid and jointed complete with collars complete all as specified and directed.

Cement concrete 1:4:8 type D-2 (using 40 mm graded aggregate) in bed to 150 mm dia pipes including packing under and haunching against the sides of pipes after they are laid and tested for complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel of 150 mm internal dia of pipe (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed.

Providing Precast cement concrete 1:2:4 type B-1 (using 20 mm graded aggregate) as in manholes cover slab etc. complete all as specified and directed by Engr-in-Charge.

Providing cement concrete 1:2:4 type B-0 in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones, bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles complete all as specified and directed.

Mild steel TMT bars 6 mm to 8 mm dia cut to length bent to shape required including cranking bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi-corrugated etc.) sheets in roof covering complete all as specifed and directed.

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.63 mm thick in ridges, hips, valley gutters at the external end slop of any colour having tansile strength 550 Mpa as in roof (ridges) covering fixed with self tapping screws and caps etc. complete all as specified and directed.

Demolition of brick work or stone/boulder masonary, built in cement mortar including all quoins, arches, pilars etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square meter each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square meter each, including cutting holes for taking out fasts or dismantling brick work (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish any extra cost to Govt) complete all as specified and directed by Eng-in-Charge.

Steel window (box type) with gaused shutter factory made with side hung shutters including pin or hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge, Glass shall be measured and paid separately.

Pressed steel frames for doors made out of 1.25 mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12 mm bar thresh hold etc. complete, of frame size 165 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

Factory made mild steel ventilators box type with upper top hung with glazing bars, shutters and bottom openable, locking arrangements type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 ii) Glazing, wire gauge and Glass shall be measured and paid for separately.

Factory made 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Glazed coloured ceramic tiles in dado/vertical surface (300 mm x 600 mm x 7 mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 laying floor finishes complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Two coat of oil bound distemper including a coat of primer including preparation of newly plastered surfaces of wall complete all as specified and directed.

Preparation of old surfaces and applying two coats of cement base paint on walls complete all as specified and directed.

Preparation old surfaces including complete removal of existing surface and applying two coats of oil bound distemper on walls complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Plinth protection 50 mm thick in PCC 1:3:6, type C-1 (using 20 mm graded stone aggregate) laid in alternate bays (not exceeding 2 Sqm each) finished even and fair at top and providing jonts throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed at site.

Taking up or down steel tubing 15 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified and directed.

Taking up or down steel tubing 20 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified and directed.

Refixing old steel water tubing 15 mm bore medium grade galvanised and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and directed.

Refixing old steel water tubing 20 mm bore medium grade galvanised and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and directed.

110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

CP waste cuppling 32 mm dia (Half thread) including waste pipe in repair complete all as specified and directed.

Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) in repair complete all as specified and directed.

Half stall Urinal Large size 420 x 395 x 635 mm snow white colour in repair complete all as specified and directed. Make : Cera

CP Pillar cock with aerator in repair complete all as specified and directed. Make : Cera

15 mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule in repair complete all as specified and directed.

Soap dish fancy type chromium plated fixed with brass screws and wooden/plastic cleats in repiar complete all as specified and directed. Make : Jaquar Cat Part No - ACN-1131N

Vitreous china was basin, angle cock including cutting for and pinning in ends of brackets or erecting stand of size 600 x 480 mm white but excluding taps, waste, chain and plug and porcelain stopper but including brackets in repair complete all as specified and directed

Towel rail 600 mm long chromium plated fixed with and including chromium plated screws in repair complete all as specified and directed

15 mm bore chromium plated bib cock with wall flange and aerator complete all as specifed and directed.

Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and directed.

Health faucet (ABS Body) with 8 mm Dia, 1.2 meter long flexible tube & wall hook with all accessories in repair all as approved and complete all as specified and directed.

Brass chromium plated shower rose 75 mm size with swivel joint fixed to pipe or union of 15 mm bore in repair complete all as specified and directed.

Sand cast iron 'P' or S trap 100 mm bore for ind type w/c complete all as specified and directed.

100 mm branch pieces single (equal or un equal) oridinary or inverted (spigot or socket type) or parallel branches complete all as specified and directed.

Dismantling water tanks exceeding 500 ltrs and not exceeding 1000 ltrs complete all as specified and directed.

Toilet cubical including pilasters supported by L-bracket with floor anchor bolt concealed with SS flat box grade 304 & 316 up to 110 mm. The intermediate high pressure laminate panels of thickness 12 mm are fixed on to the wall with SS U-channel section and SS 304 screw inserted. The ground clearance of panel not more than 100 mm.The door shutter panel included SS gravity hinges, SS door knob, alloy privacy thumb-turn with indicator, SS door stopper and SS coat hook etc. complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out, any to types of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Demolition cement concrete in ground floors and paving (unreinforced) not exceeding 15 cm thickness (below or above ground floor) complete all as specified and directed.

Rolled mild steel as in compound girders and stanchions, lattice girders, aerial masts, staging of water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates etc. confirming to grade Fe-410-W (Gde-E-250) quality B complete all as specifed and directed.

Rolled Mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed by Engr-in-Charge.

Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc. complete, drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication; also fastening and fixing complete with confirming to grade Fe-410-W (Gde-E-250) quality B complete all as specified and directed by Engr-in-Charge.

0.80 mm mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc. as required complete all as specified and directed by Engr-in-Charge.

4 mm dia galvanised steel wire, 150 x 100 mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.60 mm thick crimpted/tapard at the external end slo of any colour having tensile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc. complete all as specified and directed.

100 mm thick cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

25 mm thick PCC type B-1 (using 20 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

Coloured glazed ceramic tiles (square/ rectangular) 8 to 9 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floor joint free etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Coloured glazed ceramic tiles (square/ rectangular) 8 to 9 mm thick of dado/skirting are not exceeding 0.36 Sqm etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

A two layer wall care putty on walls including preparation etc. complete all as specified and directed. Make : JK Birla

Pressed steel frames for doors made out of 1.25 mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12mm bar thresh hold etc. complete, of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

Factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and directed.

250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. (ISI Marked)

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed including one coat of red oxide primer.

Description all as per ser item No 91 but without glazing bar complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Galvanised Mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15 mm in repair complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 250 litres and not exceeding 500 litres, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 500 litres and not exceeding 1000 litres, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Rotational moulded polythylene water storage tanks hoisted and fixed in position capacity 500 ltrs complete all as specified and directed.

Hard Drawn steel wire fabric cut to length bent to shape required and tying, welding to the angle iron frame etc. complete all as specified and directed.

Ball brass valve high pressure with polythene float and fly nut complete of size 20 mm complete all as specified and directed.

Reinforce cement concrete M-25 (20 mm graded aggregates) design mix as in chajjas complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges for rough flat finished surface of concrete complete all as specifed and directed.

10 mm thick rendering in CM 1:3 on roof sufaces, finished even and smooth without using extra cement complete all as specified and directed. Note :- Supply only water proofing compound shall be measured and paid seperately under the respective item.

Applying bituminous primer on roof surfaces @ 0.40 liters/Sqm and applying one coat of semi hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and thereafter supply and laying 3 mm thick polymeric water proofing membrane, five layered, of weight not less than 3 Kg per Sqm with centre layer core of 90 micron high molecular density polyethylene film and bonded completely to the surface with side overlap 75 mm and end ovarlaps is 150 mm (overlaps to be thermo fused by flame) followed by another coat of semi hot blown bitumen 85/25 grade bitumen @ 0.70 Kg/Sqm and provide aluminium paint as per manufacturing instruction complete all as specified and directed. Note:- Water proofing treatment will be done by IWL or through a specialized agancy.

Cast iron soil, waste and vent pipes (sand cast) 75 mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor complete all as specified and directed.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 2 core size complete all as specified and directed. Make - KEI, Finolex & Polycab. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc. for holdining of GI pipe alongwith poles complete all as specified and directed.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed.

Point wiring for one light point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes & metal back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed. Make: Havells/ Finolex/Polycab.

All as per ser item No 166 point wiring for Exh Fan point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes & metal back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed. Make: Havells/ Finolex/ Polycab.

All as per ser item No 166 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 166 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/Legrand/Philips

Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed. Make : Havells (Crabtree)/Legrand/Philips

Socket 3 Pin 6 Amps flush type (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/Legrand/Philips

Socket combined 2-in-1, 3 Pin 6 & 16 Amps flush type (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/Legrand/Philips

Ceiling rose, surface bakelite 65 x 50 mm two to three terminals fixed on PVC Round Block complete all as specified and directed. Make: Havells (Crabtree)/Legrand/Philips

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W complete all as specified and directed by Engr-in-Charge. Make - Havells Cat Pt No LHEXBXPNIN1W020 or equivalent to Syska/Wipro/Philips.

Replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 10 W complete all as specified and directed by Engr-in-Charge. Make - Havells Cat Part No LHEXBXPNIN1W010 or equivalent to Syska/Wipro/Philips.

LED Street light 30W including angle arms (Bracket) with 25mm dia GI pipe complete all as specified and directed by Engr-in-Charge. Make - Havells Cat Part No : ENDURACITYLITEPLATSL30WLED757SASYBOPC or equivalent to Syska/Wipro/Bajaj/ Philips.

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 4 way 240 volts with 200 amps rated bus bar and neutral link including chases wall for dixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make : Havells/Schneider/Legrand/HPL /Siemens

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 8 way 240 volts with 200 amps rated bus bar and neutral link in cluding chases wall for dixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make : Havells/Schneider/Legrand/HPL/ Siemens

Replacement MCB Single Pole, 230 Volt, Rating 6 to 32 Amps complete all as specified and directed. Make: Havells/ Schneider/ Legrand/HPL/Siemens

Replacement MCB Single Pole and Neutral , 230 Volt, Rating 35 to 63 Amps complete all as specified and directed. Make: Havells/ Schneider/Legrand/HPL/Siemens

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 4 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire. Make : Havells/Finolex/Polycab.

Earthing complete with galvanised steel earth plate electode 600 mm x 600 mm x 6.00 mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20 mm bore with funnel and wire mash and light grade GI protection pipe 15 mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board complete all as specified and directed and testing completion

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 6 Sqmm x 2 core size complete all as specified and directed including taking down old cable. Note : Earth work and other connected work shall be measured & paid sperately. Make: Havells/Finolex/Polycab.

All as per ser item No 166 but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

Electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as specified and directed. Make : Havells (Crabtree)/Legrand/Philips

Supply & Fixing/Hanging Ceiling fan 1200 mm sweep Havells pacer 3 blade complete set without regulator including connecting to ceiling rose with twin twisted flexible cooper cable and provisioning of suitable fan hook/ down rod including all accessories as per site requirement complete all as specified and directed. Make : Havells or equivalent to Philips/Crompton.

Replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) Cat Part No LHEOAOP7UZ6W010 230 or equivalent to Crompton/Syska complete all as specified and directed by Engineer-in-Charge.

All as per ser item No 166 but for one sheet metal enclosure single pole & neutral concealed on wall independent with PVC insulated, unsheathed FRLS cable 4.0 Sqmm copper multistrand condutor, alongwith PVC insulated and unsheathed FRLS cable 2.5 Sqmm multi stranded copper conductor earth wire connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and directed by Engr-in-Charge. Make: Havells/ Finolex/ Polycab

Sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 complete with one single pole MCB of any cap from 10 to 20 A in repair complete all as specified and directed. Make : Havells (Crabtree)/Legrand/Philips

Exhaust fan Ventil Air - DB 300 mm including louver complete all as specified and directed. Make - Havells/Polycab/Bajaj.

RAMAN CONSTRUCTION CO

AKBAR FURNITURE HOUSE AND TIMBER MERCHANT