REPAIRS MAINTENANCE TO EXTERNAL WATER SUPPLY PIPE LINES VALVES VALVE CHAMBERS AND ALLIED WORKS UNDER GE M ARKKONAM

Amount

Excavation in trenches not exceeding 1.5mtr wide & not exceeding 1.5 mtr deep getting out in soft /loose soil for taking up/laying CI/GI pipe all as directed and specified by Engr-in-charge

Returning , filling in trenches (Soft/Loose soil) in layers not exceeding 25 cm thick after laying of pipe including spreading, levelling & well ramming including watering as required all as specified and directed by Engr-in-charge

Removing surplus excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above from the starting point all as specified and directed byEngr-in-charge

Taking up or down steel tubing of following sizes from roof/ ceiling /wall /trenches complete all as specified and as directed. Note: Excavation and earth work shall be measured and paid separately under relevant items.

15 mm bore of pipe

20mm bore of pipe

25mm bore of pipe

50mm bore of pipe

80mm bore of pipe

100mm bore of pipe

150mm bore of pipe

Refixing steel tubings the serviceable portion of following size pipes retrived vide item No.04 here-in-before and fixed and connection in new or old position on wall /ceiling /floor etc. complete all as specified and as directed.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

50mm bore of pipe

80mm bore of pipe

100mm bore of pipe

150mm bore of pipe

Supply and lay tubing, medium grade galvanised with all fittings specials such as bends, elbows, tees, short pieces connection, back nuts, diminishing pieces, caps, plugs and unions etc., laid in trenches of following sizes complete all as specified and as directed. Note: Excavation and earth work will be measured and paid seperately under relevant items of schedule.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

50mm bore of pipe

80mm bore of pipe

100mm bore of pipe

Supply and lay tubing, medium grade galvanised with all fittings such as bends, elbows, tees, short pieces connection, back nuts, diminishing pieces, caps, plugs and unions etc., laid in walls, ceiling and laid in floor of following sizes complete all as specified and as directed. Note: Quoted Rate includes supply and fixing suitable MS clamps with painting and wooden plug along with screws in specified intervals.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

50mm bore of pipe

80mm bore of pipe

100mm bore of pipe

150mm bore of pipe

Material and labour for cutting bituminous road /PCC floor /plinth protection for laying pipe not exc wide 1.5m and 1.5m depth including refiling with excavated material and watering well ramming /compacting including earth work and making good with PCC complete all as specified and as directed. Note: PCC shall be measured and paid separately.

Material and labour for PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) as in filling and making good distrubed surface complete all as specified and as directed.

Material and labour for opening the top of the sluice valve of the following sizes carefully and taking out the gate including spindle and checknuts, scrapping /cleaning, replacing, regrinding of gate of sluice valve and spindle, refixing the spindle, gate check nut and top of sluice valve including repacking stuffing box of sluice valve spindle by replacement of gland packing rope of suitable size and reassembling including replacement of rubber gasket, bolts, nuts etc., and making the sluice valve serviceable complete all as specified and as directed. Note: Rate quoted deemed to include M&L cost for repair to sluice valve.

80mm dia

100mm dia

150mm dia

200mm dia

300mm dia

Taking down existing unserviceable Non return valve from the existing pipe line and supply and fix for new Non return valve CI body ISI marked class PN 1.6 heavy duty flanged ends conforming to IS-14786-2000, short body with bypass arrangement including nuts, bolts, wqashers and gasket including necessary machining work if required complete all as specified and as directed. Note: Quoted rate deemed to include making good the damaged valve chamber.

100mm dia

150mm dia

200mm dia

300mm dia

Taking down the existing unserviceable gate valve of following sizes and supply and fix new gun metal globe valve with iron wheel, screwed both ends for iron pipes complete all as specified and as directed.

15mm bore

20mm bore

25mm bore

50mm bore

80mm bore

Supply and laying 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylen random fittings fixed complete .with all fittings specials such as bend, elbows,tees, short pieces connection, back nuts, diminishig pieces, caps, plugs and unions etc laid in trenches of following size complete all as specified and as directed.

32 mm bore of pipe

63 mm bore of pipe

90 mm bore of pipe

Note: (i). Excavation and earth work will be measure and paid seperately

Supply and laying 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylen random fittings fixed complete to walls, ceilings or in floors etc with all fittings such as bend, elbows,tees, short pieces connection, back nuts, diminishig pieces, caps, plugs and unions etc laid in Walls, ceiling & laid in floor of following sizes complete all as specified and as directed.

25 mm bore of pipe

32 mm bore of pipe

63 mm bore of pipe

90 mm bore of pipe

Taking down the existing unserviceable Gate valve and supply and fix new PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

32 mm bore of pipe

63 mm bore of pipe

Material and labour for taking down and removing detoriated valve chamber cover, including fabricate and fix new valve chamber cover for chamber size 1.2x1.2m made out of 3mm thick MS sheet over MS frame work made of 40x40x5mm angle iron and duly hinged with frame including grouting/ fixing into wall of chamber and painting the entire steel work with two coats of synthetic enamel paint over a coat of red oxide and provision of locking arrangement, lifting hook etc., complete all as specified and as directed.

All as per item No.16 here-in-before but valve chamber cover for chamber size 0.90x0.90m.

All as per item No.16 here-in-before but valve chamber cover for chamber size 0.75x0.75m.

Material and labour for repair to plaster of valve chambers by preparation of bricks surface including rendering 1:4, 10mm thick of fair face of brick work including removing old damaged plaster complete all as specified and as directed.

Material and labour for brick masonry valve chamber of size 1.2x1.2x0.9m (internal size) by providing PCC 1:2:4 type B-2 foundation 100mm thick and brick work in CM 1:4 plastering 10mm thick in CM 1:4 internal surfaces and external surfaces completely and at external surfaces upto 150mm below GL, 75mm thick PCC 1:2:4 type B-2 as in coping for valve chamber cover made up of 40x40x5mm thick angle iron frame and 3mm thick MS sheet cover complete with locking arrangements and handle including painting all steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including dismantling and demolition of existing damaged valve chamber and removing debris away from the premises including necessary earth work complete all as specified and as directed.

All as per item No.20 here-in-before but valve chamber of size 0.75x0.75x0.75m (internal size).

M & L Taking up unserviceable cast iron water mains (including all fittings) with spigot and socket ends and lead joints for size 150 mm dia bore including burning out joints and recovering lead complete all as specified and as directed.

Supply and laying in trenches DI pipe K-7 with spigot ends, centrifugally cast suitable for and including rubber/ tyton joint for 150 mm bore size complete all as specified and as directed. Note: Earth work/ excavation, tyton joint, rubber joint etc shall be measured under releavent items.

Taking out the unserviceable lead joints including spun yarn and M&L for run lead joint for spigot and socket pipes and fittings of the following sizes

80 mm dia bore

100 mm dia bore

150 mm dia bore

200 mm dia bore

300 mm dia bore

Material and labour for rubber gasket tyton joint for the following sizes including taking out old unserviceable damaged joint complete all as specified and as directed.

100mm dia bore

150mm dia bore

200mm dia bore

300mm dia bore

Material and labour for bends (any radius and angle) tappers any type (straight, bend, increasing, decreasing or double socket) Tee, pieces, single branch, “ Y” junction, double branch, cross (all socket or socket spigot) collars, caps, caps and plugs suitable for DI pipe upto 150mm bore complete all as specified and as directed.

Material and labour for taking down and removing detoriated pressure gauge of any size including supplying and fixing new water pressure gauge of size 4"dial 0-21 kgs rating etc complete all as specified.

Supply only GI bolt & Nuts, washers of required different sizes all as specified and directed.

Material and labour for taking down existing damaged RCC cover from UG sump and replace with new Precast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coverslab as required for water sump set in CM 1:6 complete all as specified and directed.

Supply and fixing for TMT bar not less than 10mm dia and over, cut to length, bent to shape require, including cranking, bending spirally for hooping for slab and including binding with MS wire not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply and fixing wrap around the type single section stainless steel clamp suitable for cast for cast iron / D I pipe sections size dia 6" 300 mm x 600 mm

Supply and fixing wrap around the type single section stainless steel clamp suitable for cast for cast iron / D I pipe sections size dia 6" 300 mm x 1200 mm

Supply and fixing wrap around the type single section stainless steel clamp suitable for cast for cast iron / D I pipe sections size dia 4" 100 mm x 600 mm

Supply and fixing wrap around the type single section stainless steel clamp suitable for cast for cast iron / D I pipe sections size dia 4" 100 mm x 1200 mm

Supply and fixing wrap around the type single section stainless steel clamp suitable for cast for cast iron / D I pipe sections size dia 3" 80 mm x 600 mm

Supply and fixing wrap around the type single section stainless steel clamp suitable for cast for cast iron / D I pipe sections size dia 3" 80 mm x 1200 mm

Material and labour for brick work with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:4 complete all as specified and as directed by Engr-in-charge.

Taking down existing unserviceable sluice valve from the existing pipe line and supply and fix for sluice valve CI body ISI marked class PN 1.6 heavy duty flanged ends cast iron wheel with SS spindle (ISI marked) conforming to IS:14786-2000, short body including nuts, bolts, washers and gasket complete all as specified and as directed. Note: Quoted rate deemed to include making good the damaged valve chamber.

80mm dia

100mm dia

150mm dia

200mm dia

300mm dia

SIVA ENTERPRISES

C SRINIVASAN

VKR ENTERPRISES

Green Ray Technologies

R.P.TRADERS

M.G.Swamy.Co.,

SUSII CONSTRUCTIONS