Special Repair and Renovation of Room No.108 including attached toilet (Secretariat Complex)

Amount

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Thickness above 10 mm up to 25 mm

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

Of sectional area 40 square centimetres and above

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position :

Superior hard Wood Cat-II(A)

Providing and fixing in wall lining marine plywood (IS : 710) with necessary fixing arrangement and screws etc. complete

12 mm thick marine plywood (Century of equivalent)

Providing and applying anti termite coat of Dr. Fixit in the internal portion of wall panelling use 0.24 Ltr./Sqm.

Providing and fixing veneer plywood BURMA TEAK 4 mm thick of Superior quality including fixing with fevicol heatx heatproof adhesive etc. complete as per the direction of Engineer-in-charge.(minimum cost range of BURMA TEAK 4 mm thick veneer plywood shall be Rs. 1200/Sqm.)

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1) The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2) Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hours. 3) On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes.grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done and this surface is further allowed to dry for 12 hrs. 4) On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time)

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 3 mm dia G.I level adjusting hanging (upto 1200 mm length)for suspended ceiling,tied to M.S.roof truss complete as per direction of Engineer-In-Charge.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer Godrej or equavalent (having brand logo with ISI mark embossed on the body, door weight upto 60 kg and door width upto 900 mm), with necessary accessories and screws etc. complete.

Providing and fixing designer cement board (of size 610x610 mm ) and fixed in aluminium frames as per the direction of ENgineer-In-Charge (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Providing and fixing 1st qaulity Hi-lighter wall tiles (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Size 600x300 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:

One or more coats on old work

Providing and fixing 450x120x5 mm glass shelf make FFI-life Cat No.E 730 or equavalent ,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing Hand Shower (Health Faucet) with 8 mm dia, 1.20 meter long flexible tube & wall Hook (Code No.ALD- 573) Make Jaquar.

Providing and fixing towel rail 600 m long of make Jaquar( ACN-CHR-1111SM) or equivalent with neccessary screws anf wooden cleats etc. as per the direction of engineer in- charge.

Providing and fixing towel ring round of make Jaquar of model no. ACN-1121BN or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing Bib Cock 2 in 1 of make Jaquar of model no. FLR 5041 N or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing Angular Stop Cock with wall flange of make Jaquar (CON-059 KN) as per the direction of engineer in- charge.

15 mm nominal bore

Providing and fixing wall Hung Basin with fixing Accessories set, Size 565x440x210mm (Model No. FLS-WHT-5801) FLS-WHT-5301 full pedestal for FLS-WHT-5801 with basin tap 1/2" (FLR-CHR 5011N ) and Waste coupling 32mm Size Full Thread with 80mm height (ALD-705) of make jaquar or equivalent of approved quality as per the direction of Engineer-In-Charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length (24.1.1.) 15 mm nominal bore

Providing and fixing stainless steel grating of approved qualityfor gully trap.

Stainless steel grating 100x100 mm sqaure type

Providing and fixing single piece water closet with accessaries of make Jaquar of model no. LYS-WHT-38851 SSM 's' or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing Toilet Roll Holder of make Jaquar of model no. ACN-1153S or equivalent of good quality as per the direction of Engineer-In-Charge.

M/s Sagar Enterprises

S B SENGUPTA

K SRINIVAS RAO