Construction work of non-residential building of new Police station in senduria in Maharajganj distirct Lot No 1 of 1

Amount

[MAIN BUILDING,SERVICE BLOCK, Gurard Room & Pump Room] Excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.5 m. & Iead upto 30 m. Including filling, watering & ramming of excavated earth into the trenches or into the space between the building & the sides of foundation trenches or in to the plinth removal & disposal of surplus earth as directed by the engineer in charge upto a distance of 30m from the foundation trenches. (Excluding Royalty).as per SI No-251 (GST shall be paid extra)

Filling of carted earth (GST shall be paid extra)

Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 km. from the site of work & including watering,dressing etc. Rate includes cost of all materials, labour and T&P etc. required for proper completion of the work.(Excluding royalty)as per SI No-255 (GST shall be paid extra)

Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinthlevel :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) as per SI No-281. (GST shall be paid extra)

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at ground (4) Treatment junction of wall and the floor 7.5 liters/sqm (5) Treatment of soil along external perimeter of building 7.5 litres/sqm (6) Treatment of soil under spron along external perimter 5 liters/sqm. (As per manufacture's standard dilution) as per PWD Chapter-7 PWD CH 7 ITEM NO.1 (GST shall be paid extra)

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles DSR 20.3.1 (GST shall be paid extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work Upto Plinth Lvl.) DSR 5.33.1(GST shall be paid extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work ABOVE Plinth Lvl.) (a) Ground Floor DSR-5.33.2 (GST shall be paid extra)

(b) First Floor DSR-5.33.2 (GST shall be paid extra)

© Second Floor DSR-5.33.2 (GST shall be paid extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work ABOVE Plinth Lvl.) (a) Ground Floor DSR-5.33.2 (GST shall be paid extra)

(b) First Floor DSR-5.33.2 (GST shall be paid extra)

© Second Floor DSR-5.33.2 (GST shall be paid extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work Upto Plinth Lvl.) DSR 5.33.1 (GST shall be paid extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work ABOVE Plinth Lvl.) DSR 5.33.1 (a) Ground Floor DSR 5.33.1 (GST shall be paid extra)

(b) First Floor DSR 5.33.1 (GST shall be paid extra)

© Second Floor DSR 5.33.1 (GST shall be paid extra)

M-15 brick work in 1:6(one cement and six coarse sand mortar in foundation & plinth including supply of all materials, labour and T & P etc. required for proper completion of the work. as per SI No-305 (GST shall be paid extra)

Same as in item no. 13 above but in super structure above plinth level up to floor two level(up to two storeys) including neecssary cutting and moulding of brick work as rrequired and also including honeycombed brick work in thickness of wall more than 12cms(1:6 cement:coarse sand) as per SI No-303+309+310 (a) Ground Floor (GST shall be paid extra)

(b) First Floor (GST shall be paid extra)

© Second Floor (GST shall be paid extra)

Same as SI No.305 but in 1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work as per SI No-305+309+310+310a (a) Ground Floor (GST shall be paid extra)

(b) First Floor (GST shall be paid extra)

© Second Floor (GST shall be paid extra)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). (DSR-4.10) (GST shall be paid extra)

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. (DSR-4.13) (GST shall be paid extra)

Providing and laying brick coba 120 mm thick laid with M-150 class brick bat coba 7.50 mm thick with gap of 150 mm to each other, over 20 mm thick base of cement mortar 1:4 cement coarse sand mixed with wtare proofing compound spreading cement slurrymixed with aerelic cement concrete water proofing compound filled gap of coba and top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand finished smooth & top mashed false square 30cm x 30 cm and side wall paraper shall be mono tythic plaster wall upto 30cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary .coba with top finished plaster mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour, T & P etc. complete for proper complition of work. (PWD CH-11 ) (GST shall be paid extra)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (a) Single leaf [PWD 470ii] (GST shall be paid extra)

(b) Double leaf [PWD 470,ii+iv] (GST shall be paid extra)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (GST shall be paid extra)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: Fixing with adjustable lugs with split end tail to each jamb SOR. 10.14.3 (GST shall be paid extra)

Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. PWD-502 AR-V (GST shall be paid extra)

Providing & fixing fly proof galvanised M.S. wire gauze to windows, clerestory windows using galvanised M.S. wire guage with average width of aperture 1.4 mm in both direction with wire of dia 0.63 mm .With second class teak wood beading 62 x 19 mm. PWD 9.51.1 (GST shall be paid extra)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces (DSR-10.5.1) (GST shall be paid extra)

Fixing of Door, windows/ ventilators chaukhats in position. (a) Doors chaukhats as per Market Rate (GST shall be paid extra)

(b) Windows chaukhats as per Market Rate (GST shall be paid extra)

© Ventilators chaukhats as per Market Rate (GST shall be paid extra)

Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage and over lapping & hooks.As per SI No 504 (a) UP TO PLINTH LVL. Ground Floor PWD-504 A.R.-II (GST shall be paid extra)

(b) UP TO PLINTH LVL. G.F. & F.F PWD-504 A.R.-II (GST shall be paid extra)

© ABOVE PLINTH LVL SECOND FLOOR PWD-504 A.R.-II (GST shall be paid extra)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) (DSR-13.5.1) (GST shall be paid extra)

12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. (1)1 cement : 6 coarse sand PWD-586+(584a-584) (a) Ground Floor & First Floor (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 coarse sand.PWD-586+(584a-584)+596 (a) Ground Floor & First Floor (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Engraving lines in plaster of outer face wall vertically and horizontally to display the surface as stone facing as directed by the Engineer-incharge including supply of all materials, labour tools and plants etc required for proper completion of the work. PWD 598 (GST shall be paid extra)

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in- Charge.PWD 13.76 (GST shall be paid extra)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. as per chapter-13 SOR 13.76 (GST shall be paid extra)

2.5 cm (1 thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2 cm.(3/4")graded approved stone shingle laid in panels finished with 3 mm.(1/8")floating coat of neat cement or cement and marble dust in 5:1 as specified over & including 8cm.(3") 'thick. base concrete consisting of cement ,local sand and brick ballast 4cm.(1½") gauge in the proportion of 1 :4:8 and removing any over lapping mortar at the joints of Panels if any and giving them a uniform finish including supply of all materials, labour' and T&P etc. requierd for proper completion of the work but without base concrete as per SI No-601A (GST shall be paid extra)

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. [DSR-11.4] (GST shall be paid extra)

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick DSR 11.6.1 (GST shall be paid extra)

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. (a) 3.15mm wide and 35 mm thick PWD 631,b (GST shall be paid extra)

Cement concrete with 20mm gauge dalla stone aggregate approved chopan coarse sand and cement in the proportion of 4:2:1 in hold fast including supply of all materials, labour and tools and plants etc. required for proper completion of work. As per s.i.no. 279(I) PWD - 279,(I) (GST shall be paid extra)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (a) Ground Floor & First Floor (PWD-11.41.2) (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (a) Ground Floor & First Floor (PWD-11.41.2) (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Laying of 25mm thick Kota stone of size 45x45cm & above flooring over previously base with 2 cm thick 1:3 cement and sand mortar including filling of joints with cement mixed with pigment required for matching the shade of floor as per direction of E/I including cutting polishing with wax polish including supply of all materials T & P etc required for proper completion of the work . (PWD-CH-14 NEW ITEM-1) (a) Ground Floor & First Floor (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Same as above but in dado with 25 mm thick stone. (PWD-CH-14 NEW ITEM-2) (a) Ground Floor & First Floor (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Supply and fixing of 6mm thick China white glazed tile in flooring or dado laid with 1:3 (1 cement : 3 coarse sand) mortar finished with white cement jointed and polishing complete including supply of all materials, labour for proper completion of the work. PWD 628 (a) Ground Floor & First Floor (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade (Area of slab upto 0.50 sqm) (a) Ground Floor & First Floor CPWD-8.2.2.1 (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.PWD CH.-15 (1a+2+4(ii )(GST shall be paid extra)

Same as above but wooden painting PWD CH.-15 (1b+2+4(ii ) (GST shall be paid extra)

Finishing walls with Acrylic smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67ltr/10 sqm over the including base coat of water proofing cement paint applied @ 2.20 kg/10 Sqm. PWD 13.46.1 (GST shall be paid extra)

Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (PWD - 649+650)(GST shall be paid extra)

Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials.(PWD - 649+650) (a) Ground Floor & First Floor (GST shall be paid extra)

(b) Second Floor (GST shall be paid extra)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (DSR-13.80) (GST shall be paid extra)

Fixing panes of glass with and including putty and brads and including supply of all material labour and tools plants etc. required for proper completion of the work, but excluding cost of glass 3.8 to 4.7 mm thick Chapter 21as per S.I.No. 812 (B) (GST shall be paid extra)

Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . PWD CH.-1, 10 (f) (GST shall be paid extra)

Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete PWD CH.-1, 10 (d) (GST shall be paid extra)

Providing and fixing stainless steel handles with screws etc. complete (a) 125 mm PWD CH.-1, 10 (h) (GST shall be paid extra)

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. (DSR- 14.34) (GST shall be paid extra)

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Ordinary cement without any pigment. (DSR-11.20.4) (GST shall be paid extra)

Providing & laying of light cinder filling under floor of toilets & other sunken roofs. PWD MAT. Ch-1 items 6 (GST shall be paid extra)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.(DSR-22.5) (GST shall be paid extra)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (DSR-10.28)(GST shall be paid extra)

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding DSR-14.72 (GST shall be paid extra)

Providing & Installation of Microcell Polycarbonate panels of 16mm thick (min.) single panel. Panel Width shall not be less than 1040 mm to ensure best performance for wind uplift, vibration, oil canning and visual appearance. The panels shall be uniform in color with an integral Microcell/ Multicell. Panels shall be manufactured with Vertical Standing Seam with maximum height 15mm at both sides of the panel. Snap-on connector to interlock the panels shall have a double tooth grip-lock locking mechanism to ensure maximum uplift capability. Panel shall be with additional End- cap/Aluminum U-Profile (mill finish) for ends. Panels shall be co-extruded UV protected. Panel shall be fixed over structural steel / MS purlin (will be paid as extra) conforming to the detail technical specifications enclosed and as per approved shade / colour and directions of Engineer-In-Charge. Quotation (GST shall be paid extra)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter [DSR-12.41.2] (GST shall be paid extra)

Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories forunplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend [DSR-12.42.5.2] (GST shall be paid extra)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm [DSR-12.43.2] (GST shall be paid extra)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. as per DSR 12.22 (GST shall be paid extra)

Supplying and fixing rolling shutters of approved make.80x125 mm guage cold rolled M.S. laths, interlocked together through their entire length and jointed together at the end by end locks and mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, excluding the cost of top cover & springs. PWD 520 (GST shall be paid extra)

Providing and fixing 27.5cm long wire spring grade no. 2 for rolling shutters. PWD 521 (GST shall be paid extra)

Providing and fixing top cover for rolling shutters.18 guage PWD 522 (GST shall be paid extra)

Providing and fixing ball bearing for rolling shutters. PWD 523 (GST shall be paid extra)

Centering and shuttering including strutting, propping etc. and removal of form for all heights : (UPTO PLINTH LVL.) Foundations, footings, bases of columns, etc. for mass concrete.DSR-5.9.1 (GST shall be paid extra)

(a) (ABOVE PLINTH LVL.) Suspended floors, roofs, landings, balconies and access platform.DSR-5.9.20 (GST shall be paid extra)

(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers.DSR-5.9.21 (GST shall be paid extra)

© Columns,Pillars, Piers, Abutments, Posts and Struts.DSR-5.9.6 (GST shall be paid extra)

R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. including cost of binding wire. The rate excludes making of drip course which shall be paid extra. [M-20] PWD-283A (GST shall be paid extra)

As above item but for slabs (Using 1:1.5:3 Mix concrete).[M-20] PWD-284A (GST shall be paid extra)

As above item for the lighter beams i.e. having spans upto 6 m. (Using 1:1.5:3 Mix concrete) PWD- 285 (GST shall be paid extra)

As above item but in R.C.C. Raft foundation and footing with approved stone ballast.(Using 1:1.5:3 Mix concrete) M-20 PWD- 287 (GST shall be paid extra)

As above item but in R.C.C. columns in 1:1.5:3 having strength not less than M-20. (PWD - 289) (GST shall be paid extra)

Providing and laying damp-proof course 25 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). (DSR 4.10) (GST shall be paid extra)

12 mm cement plaster in single coat on rough side for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 coarse sand 1.25 FM PWD-584A (GST shall be paid extra)

12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. (1)1 cement : 6 coarse sand 1.25 FM PWD-584A+596 (GST shall be paid extra)

6mm thick plaster in 1:3 on ceiling and soffits of stairs upto floor two level. PWD-583+587 (GST shall be paid extra)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick .PWD-605 (GST shall be paid extra)

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick PWD-13.7.1 (GST shall be paid extra)

Supply and fixing mosquito proof jali with sheesham wood batten around the jali including the ocst ofjali, buton, nails, screws etc. required for proper S.I.No. 456 (GST shall be paid extra)

Finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, tools and plant etc. required for proper completion of the work. (Two Coat) (PWD-660 +661) (GST shall be paid extra)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. PWD-13.26 (GST shall be paid extra)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. DSR-9.82 (GST shall be paid extra)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm. PWD-9.62.2 (GST shall be paid extra)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250 mm Long PWD-9.63.1 (GST shall be paid extra).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 200 mm Long PWD-9.63.2 (GST shall be paid extra)

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm. PWD-9.66.1 (GST shall be paid extra)

Same as above but on new wood surface. (PWD 1b+2+4 (iii)) (GST shall be paid extra)

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. (a) 40 mm wide and 4 mm thick PWD-631 D (GST shall be paid extra)

Providing & fixing glazing in Z-section, windows, doors, ventilator shutters and partitions etc with glass putty / beading etc. 4.0 mm thick glass panes PWD-812 A (ii) (GST shall be paid extra)

WATER SUPPLY, SANITARY & SEWERAGE WORKS Providing and fixing water closet squatting pan ( Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS:7231,Parryware/ Hindware / Seabird /Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests as per DSR 2021 17.1.1 (GST shall be paid extra)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, Parryware/ Hindware/ Seabrid /Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required W.C. pan with ISI marked black solid plastic seat and lid as per DSR 2021 17.2.1 (GST shall be paid extra)

Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15 mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mm C.P. brass waste of standerd pattern including cutting & making good the walls wherever required.a)White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps as per DSR 2021 17.7.1 (GST shall be paid extra)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe 32 mm dia as per DSR 2021 17.28.1.1 (GST shall be paid extra)

40 mm dia as per DSR 2021 17.28.1.2 (GST shall be paid extra)

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. as per DSR 2021 17.31 (GST shall be paid extra)

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm as per DSR 2021 17.10.1.1 (GST shall be paid extra)

Providing and fixing white vitreous china flat back half stall urinal of size 580*380*350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in D.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required Range of Three half stall urinals with 10 litre PV.C. automatic flushing cistern. As per DSR 2021 17.5.3 (GST shall be paid extra)

Range of Two half stall urinals with 5 litre PV.C. automatic flushing cistern. As per DSR 2021 17.5.2 (GST shall be paid extra)

Range of Single half stall urinals with 5 litre PV.C. automatic flushing cistern. As per DSR 2021 17.5.1 (GST shall be paid extra)

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade as per DSR 2021 8.10.2 (GST shall be paid extra)

Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms as per DSR 2021 17.70.2 (GST shall be paid extra)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. as per DSR 2021 17.71 (GST shall be paid extra)

. Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms as per DSR 2021 17.73.2 (GST shall be paid extra)

Providing and fixing unplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore as per DSR 2021 18.21.2.1 (GST shall be paid extra)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore as per SOR 18.49.1 (GST shall be paid extra)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore as per SOR 18.51.1 (GST shall be paid extra)

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 15 mm nominal bore as per SOR 18.53.1 (GST shall be paid extra)

Providing and fixing C.P. brass shower rose with 15 or 20mm inlet 100 mm diameter as per SOR 18.22.1 (GST shall be paid extra)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15mm nominal bore as per SOR 18.52.1 (GST shall be paid extra)

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground) 100 /90 mm dia as per DSR 2021-9.2.1 (GST shall be paid extra)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. 110 mm as per DSR 2021- 12.41.2 (GST shall be paid extra)

Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. Bend 87.5 degree 110 mm Bend as per DSR 2021- 12.42.5.2 (GST shall be paid extra)

Shoe (Plain) 110 mm Shoe as per DSR 2021- 12.42.6.2 (GST shall be paid extra)

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. as per DSR 2021- 12.44 (GST shall be paid extra)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.(a) 20mm dia nominal outer dia pipes as per DSR 2021- 18.8.2 (GST shall be paid extra)

(b) 25mm dia nominal outer dia pipes as per DSR 2021- 18.8.3 (GST shall be paid extra)

(c) 32mm dia nominal outer dia pipes as per DSR 2021- 18.8.4 (GST shall be paid extra)

Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good walls etc. (internal work).Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. as per DSR 2021 18.78 Internal work-Exposed on wall (a) 25 mm dia nominal bore as per SOR 2021- 18.10.3 (GST shall be paid extra)

(b)32 mm dia nominal bore as per SOR 2021- 18.10.4 (GST shall be paid extra)

© 40 mm dia nominal bore as per SOR 2021- 18.10.5 (GST shall be paid extra)

(d) 50 mm dia nominal bore as per SOR 2021- 18.10.6 (GST shall be paid extra)

Painting GI pipes and fittings with SYNTHETIC enamel paint over a ready mixed priming coat, both of approved quality for new work. (a) 25 mm dia nominal bore as per SOR 2021- 18.38.3 (GST shall be paid extra)

(b) 32 mm dia nominal bore as per SOR 2021- 18.38.4 (GST shall be paid extra)

© 40 mm dia nominal bore as per SOR 2021- 18.38.5 (GST shall be paid extra)

(d) 50 mm dia nominal bore as per SOR 2021- 18.38.6 (GST shall be paid extra)

Providing and fixing GI Union in GI pipes including cutting and threading the pipe and making long screws etc. complete (new work). (a) 25 mm dia nominal bore as per SOR 2021- 18.46.3 (GST shall be paid extra)

(b) 32 mm dia nominal bore as per SOR 2021- 18.46.4 (GST shall be paid extra)

© 40 mm dia nominal bore as per SOR 2021- 18.46.5 (GST shall be paid extra)

(d) 50 mm dia nominal bore as per SOR 2021- 18.46.6 (GST shall be paid extra)

Providing and fixing gun metal gate valve with wheel of approved quality. (a) 25 mm dia nominal bore as per SOR 2021- 18.17.1 (GST shall be paid extra)

(b) 32 mm dia nominal bore as per SOR 2021- 18.17.2 (GST shall be paid extra)

© 40 mm dia nominal bore as per SOR 2021- 18.17.3 (GST shall be paid extra)

(d) 50 mm dia nominal bore as per SOR 2021- 18.17.4 (GST shall be paid extra)

Providing and placing on terrace (at all floor levels)polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank.[Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license].Capcity in Per Liters as per SOR 18.48 (GST shall be paid extra)

SEWERAGE WORK Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. as per SOR 2.10.1.2 (GST shall be paid extra)

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.100mm diameter as per SOR 19.1.1 (GST shall be paid extra)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design 100mm dia SW pipe as per SOR 19.2 (GST shall be paid extra)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm RCC pipe as per SOR 19.6.2 (GST shall be paid extra)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. RCC Pipes as per SOR 19.3.2 (GST shall be paid extra)

Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design150 x 100 mm size P type With Sewer bricks conforming to IS : 4885 as per SOR 19.4.2.2 (GST shall be paid extra)

Supplying and fixing C.I.cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 Kg. as per SOR 19.20 (GST shall be paid extra)

Providing and fixing 100 mm sand cast Iron grating for gully trap. as per SOR 17.29 (GST shall be paid extra)

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With FPS bricks of class designation 75 For Sewer Line as per SOR 19.7.1.1 (GST shall be paid extra)

Extra for depth for manholes: Size 90x80cm with FPS bricks class I).as per SOR 19.8.1.1 (GST shall be paid extra)

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar as per SOR 19.15.1 (GST shall be paid extra)

Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Double socketed pipes. As per NSR (a) 110mm dia P.V.C. pipe (GST shall be paid extra)

(b) 90mm dia P.V.C. pipe (GST shall be paid extra)

Providing & fixing UPVC Floor trap of self cleansing design with CP Jali complete in all respects. (Make : Supreme / Finolex / Prince) P-Trap type Floor Trap 110 x 90 mm as per NSR (GST shall be paid extra)

Providing and fixing terminal guard. 110mm as per NSR (GST shall be paid extra)

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. As per NSR (a)110mm bend (GST shall be paid extra)

(b) 90 mm bend (GST shall be paid extra)

© Coupler 110mm (GST shall be paid extra)

(d) 90mm (GST shall be paid extra)

(e) Single tee with door 110x110x110 mm (GST shall be paid extra).

Providing and fixing clean out plug 110 mm dia. AS PER NSR (GST shall be paid extra)

SEPTIC TANK & SOAK PIT Excavation in Foundation in ordinary soil (Loam clay, or sand) including lift upto 1.5 metre (5 fts.) and lead upto 30m (100 fts) & including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 m. (100 fts) from the foundation trenches. (Rate is including Royality). (a)From 0.00 mt to 1.50 mt PWD-251 (GST shall be paid extra)

(b) In all kind of soil upto 1.5m to 3.0m. Depth PWD-251+254 (GST shall be paid extra)

© In all kind of soil upto 3.0m to 4.5m. Depth PWD-251+254*2 (GST shall be paid extra)

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors. PWD-281 A.R.-II (GST shall be paid extra)

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200. As in item no. 3 above but for slabs (Using 1:1.5:3 Mix concrete) PWD-284A A.R.-II (GST shall be paid extra)

M-150 brick work in 1:4 (one cement and four coarse sand sand of 2.25 fineness modulus) mortar in foundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. PWD-305 A.R.-II (GST shall be paid extra)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. PWD-504 A.R.-II (GST shall be paid extra)

15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 4 Coarse sand (DSR-13.5.1) (GST shall be paid extra)

Providing & fixing 75mm dia vent pipes. (DSR.17.35.2.1) 75 mm diameter : Sand cast iron S&S as per IS - 1729 (GST shall be paid extra)

Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. (DSR.19.15.1) (GST shall be paid extra)

Providing & fixing of 75mm dia cast iron terminal guard. (DSR-17.56.2.1) (GST shall be paid extra)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter DSR.19.19.2.2 (GST shall be paid extra)

M.D. -2.5- Circular shape 450mm internal diameter DSR.19.19.1.3 (GST shall be paid extra)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design With F.P.S. bricksDSR.19.32.1 (GST shall be paid extra)

EXTERNAL WATER SUPPLY & SEWERAGE WORK Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth (a) Pipes 80 mm to 300 mm diameter 2.10.1.2 (GST shall be paid extra)

(b) 1.50 m to 3.00 m depth Pipes 80 mm to 300 mm diameter 2.11 (GST shall be paid extra)

Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) (a) Depth not exceeding 1.5 meter 2.20.1 (GST shall be paid extra)

(b) Depth 1.5 to 3.00 meter 2.20.2 (GST shall be paid extra)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC Pipes 19.6.2 (GST shall be paid extra)

Providing and laying cement concrete 1:5:10(1cement:5coarse sand :10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia.19.3.2 (GST shall be paid extra)

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With common burnt clay FPS (non modular) bricks of class designation 75 (i) For Sewer Line 19.7.1.1 (GST shall be paid extra)

Extra for depth for manholes: Size 90x80cm with With common burnt clay FPS (non modular) bricks of class designation 7.5 19.8.1.1 (GST shall be paid extra)

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :With common burnt clay FPS (non modular) bricks of class designation 75 (i) For Sewer Line 19.7.3.1 (GST shall be paid extra)

Extra for depth for manholes: Size 90x120cm with With common burnt clay FPS (non modular) bricks of class designation 7.5 19.8.2.1 (GST shall be paid extra)

Providing orange colour safety foot rests of minimum 6 mm thick plastic encapsulated as per IS:10910 on 12 mm dia steel bar conforming to IS:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 19.16 (GST shall be paid extra)

Providing & fixing G.I. pipes complete with G.I. fittings including tenching and refilling etc. (external work) (a) 65mm nominal bore. 18.12.7 (GST shall be paid extra)

(b) 50mm nominal bore. 18.12.6 (GST shall be paid extra)

© 25mm nominal bore. 18.12.3 (GST shall be paid extra)

Supplying and fixing of specials for pressure pipe. 10% (GST shall be paid extra)

Providing and fixing gate valve (with cap complete with bolts, nuts, rubber insertion etc. (a) 65mm nominal bore. 18.17.5 (GST shall be paid extra)

(b) 50mm nominal bore. 18.17.4 (GST shall be paid extra)

© 25mm nominal bore. 18.17.1 (GST shall be paid extra)

Constructing brick masonry chamber 600 x 600 x 750 mm inside with F.P.S. brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice Valve / Air Valve, with C. I. surface box 100 mm top diameter, 160 mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20 mm nominal size); necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design 18.33.1 (GST shall be paid extra)

Supply, Installation, testing & commissioning of WILO make Vertical in line pumping set complete. The rate shall include the cost of electrical panel and piping work complete Domestic Water Supply pumps : Capacity/Flow Rate - 300 LPM Head - 35 m Location - Pump Room at UGT (1 set = 3nos(2W+1S) as per Market Rate (GST shall be paid extra)

C.C. ROAD & INTERLOCKING Earth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 50 meter and including filling, watering and ramming of excavated earthdisposal of sur-plus earth as directed by the Engineer incharge up to a distance of 50 meters from the foundation trenches. (PWD-251) (GST shall be paid extra)

Providing and laying in cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded Stone aggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors. PWD-281 A.R.-II (GST shall be paid extra)

M-150 brick work in 1:4 (one cement and four coarse sand sand of 2.25 fineness modulus) mortar in foundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. PWD- 305 A.R.-II (GST shall be paid extra)

Laying C.C. Road slab 10cm (4") thick consisting of 1:1.5:3 cement,coarse sand & Approved 2 cm gauge stone girt, over prepared sub grade after its rectification & bringing it to proper camber & including supply of all matterial,labour T&P.etc required for proper completion of the work, finished to required templete as directed by E/I but excluding cost of metal required for reflection of the sub grade. Take a slab length of 33 ft and 4" in depth. As per S.I.No. 773A (Road Work) (GST shall be paid extra)

Providing and laying of factory made 80 mm thick rubber moulded Interlocking cement concrete tiles (30mpa) including 25mm thick compacted bed of fine sand compacting and proper embedding/ laying of Interlocking tiles leveling and dressing of surface to required level and slope, filling joints with fine sand including the cost of material, labour T&P etc.required for proper completion of work as directed by Engineer-in-Charge. ROAD WORK NEW ITEM S.NO-1 (GST shall be paid extra)

OPEN SURFACE DRAIN (DRAIN SIZE 450X600mm) & Drain Along Apron Excavation of foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches. PWD-251 (GST shall be paid extra)

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone ballast 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors. (PWD-281) A.R.-II (GST shall be paid extra)

First Class brick work in 1:4 cement and coarse sand of 2.25 F.M. mortar in foundation and plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work. (1:4 cement & coarse sand).PWD-305 A.R.-II (GST shall be paid extra)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) (DSR-13.5.1) (GST shall be paid extra)

25mm thick 1:2:4 plain cement concrete floor (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement.PWD 601,a (GST shall be paid extra)

TUBE WELL AND INSTALLATION OF SUBMERSIBLE PUMP Shifting of D.C. Type drilling rig machine (GST shall be paid extra)

Erection of Drilling rig machine (GST shall be paid extra)

Drilling of 400 dia bore hole (GST shall be paid extra)

Dismentalling of drill machine (GST shall be paid extra)

Assembly lowering 200mm and 160mm PVC pipe (GST shall be paid extra)

Transportation Development unit for tubewell (GST shall be paid extra)

Development of tubewell by air compressor (GST shall be paid extra)

Water arrangement charges (GST shall be paid extra)

Development of tubewell by O.P. unit (GST shall be paid extra)

Cost of 200 mm dia Housing PVC pipe 10Kg/Cm2 (GST shall be paid extra)

Cost of 160 mm dia Plain PVC pipe 10Kg/Cm2 (GST shall be paid extra)

Cost of 160 mm dia Slotted PVC pipe (GST shall be paid extra)

Cost of PVC Socket 200mm dia (GST shall be paid extra)

Cost of Reducer. Socket 200x160mm (GST shall be paid extra)

Cost of PVC Socket 160mm dia (GST shall be paid extra)

Cost of Bail Plug 160mm dia (End cap) (GST shall be paid extra)

Cost of Well cap 200mm dia (GST shall be paid extra)

Cost of Pee gravel (GST shall be paid extra)

S/F 5.0 H.P. Submersible Pump with control pannel, cable, columnpipe and all accessories complete. (GST shall be paid extra)

Cost of Chlorinator (GST shall be paid extra)

Testing of streata sample chart complete. (GST shall be paid extra)

RAIN WATER HARVESTING WORKS RECHARGE PITS Earth work in exacavation in trenches for foundations and for pipes cables etc. in ordinary soil(loam clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c with in a lead of 50m. (a) In all kind of soil upto 1.5m depth PWD-251 (GST shall be paid extra)

(b) In all kind of soil upto 1.5m to 3.0m. Depth PWD-251+254 (GST shall be paid extra)

© In all kind of soil upto 3.0m to 4.5m. Depth PWD-251+254*2 (GST shall be paid extra)

(d) In all kind of soil upto 4.5 m to 6.0m. Depth PWD-251+254*3 (GST shall be paid extra)

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors.PWD-281 A.R.-II (GST shall be paid extra)

M-150 brick work in 1:4 (one cement and four coarse sand sand of 2.25 fineness modulus) mortar in foundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. PWD-305 A.R.-II (GST shall be paid extra)

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200. As in item no. 3 above but for slabs (Using 1:1.5:3 Mix concrete)PWD-284A A.R.-II (GST shall be paid extra)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. PWD-504 A.R.-II (GST shall be paid extra)

15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 4 Coarse sand (DSR-13.5.1) (GST shall be paid extra)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:With 20x20mm square bar DSR-19.15.1 (GST shall be paid extra)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter DSR-19.19.2.2 (GST shall be paid extra)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. Drilling of 300mm dia bore hole manually. DSR 23.2.1.1 (GST shall be paid extra)

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia DSR-23.4.2 (GST shall be paid extra)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.5 (GST shall be paid extra)

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.6 (GST shall be paid extra)

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. DSR-23.7 (GST shall be paid extra)

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. DSR-23.8 (GST shall be paid extra)

DRAINAGE WORK Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth Pipes 80 mm to 300 mm diameter DSR-2.10.1.2 (GST shall be paid extra)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC Pipes DSR.19.6.2 (GST shall be paid extra)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. DSR-19.3.2 (GST shall be paid extra)

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of .class designation 7.5 DSR-18.33.1 (GST shall be paid extra)

BOUNDARY WALL AND GATE Excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches. (PWD-251) (GST shall be paid extra)

Providing and laying in cement concrete 1:4:8 (1 cement : 4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors. (PWD-281) A.R.-II (GST shall be paid extra)

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles DSR 20.3.1 (GST shall be paid extra)

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200. R.C.C. work in beam PWD-285 A.R.-II (GST shall be paid extra)

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone ballast in the proportion of 1:1.5:3 (M-20) in raft foundation and footing excluding supply of reinforcement and its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire cost being inluded in the item. PWD-287 A.R.-II (GST shall be paid extra)

Same as item no. 4 but R.C.C. work in Column PWD-289 A.R.-II (GST shall be paid extra)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. PWD-504 A.R.-II (GST shall be paid extra)

Brick work in super-structure in 1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work. (PWD-305+309+ 310+310a A.R.-II (GST shall be paid extra)

12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. (1)1 cement : 6 fine sand. PWD-586+(584a-584) (GST shall be paid extra)

Finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, tools and plant etc. required for proper completion of the work.(PWD-660+661) (GST shall be paid extra)

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.(DSR-4.13) (GST shall be paid extra)

As in item 3 above but in R.C.C. columns in 1:1.5:3 having strength not less than M-20. PWD-289 A.R.-II (GST shall be paid extra)

M.S. or Iron work in heavy sizes such as trusses, built up gates, record rack, roof work , gates etc wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. (PWD 503) (GST shall be paid extra)

Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.PWD CH.-15 (1a+2+4(ii ) (GST shall be paid extra)

Cattle Catcher Excavation in foundation in ordinary soil (Loam, clay or sand) including lift upto 1.50m and lead upto 30m. and including filling, watering and ramming of excavated earth in to the space between the building and side of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by engineer in charge. As per S.I. No. 251 (GST shall be paid extra)

Concrete with 40mm gauge Stone ballast, chopan sand of and cement in the proportion of 8:4:1 including supply of all materials labour and tools and plants etc. required for proper completion of work. S.I. No. 281 A.R.-II (GST shall be paid extra)

M-150 class brick work 1:3 cement and approvel coarse sand in super structure and plinth including supply of all material, labour and tools and plants etc. required for proper completion of work. But walls of half brick 115 mm thick add for extra lab our over item no. S.I.No.307+309+310+310A (GST shall be paid extra)

Cement concrete with 20mm gauge dalla stone aggregate approved chopan coarse sand and cement in the proportion of 4:2:1 in hold fast including supply of all materials, labour and tools and plants etc. required for proper completion of work. As per 279(I) (GST shall be paid extra)

25 mm thick 1:2:4 cement conc. Flooring with cemnet, approved coarse and 2 cm. Graded approved stone balast laid in planels finished with 3 mm (1/8") floating coat of neat cement or cement and marble dust in ratio of 5:1 as specific over and iremoving any overlapping mortar at the joints of the panels if any giving them of all materials, labours, T& P etc. required for proper completion of the work. As per 601A (GST shall be paid extra)

12 mm thick plaster in dado or skerting in 1:3 cement coarse sand with neat cement finish. As per s.i.no. 583 (GST shall be paid extra)

Mild steel or iron work in heavy sizes such as trusses, built up gates, record racks, roof work, gates etc. wrought to required form, including drilling holes riverting or welding where necessary & their fixing, required for proper completion of the work. As per s.i.no. 503 (GST shall be paid extra)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (i) 80 mm dia nominal bore (GST shall be paid extra)

Supply/Filling of Carted Earth Total Filling in Campus (GST shall be paid extra)

ELECTRICAL WORK W.P for light with 1.5 mm2 FRLSH PVC inusulated multistrand single core cu. Conductor cable in PVC conduitpartiallyconcealed in wall and partially laid in slab along with the reinforcement before concreting with 1.5 sq mm FRLSH PVC inusulated multistrand copper conductor cable as earth wire drawn inside the conduit with modular switches. as per PS No. 131( C ) &187(A) (GST shall be paid extra)

Same as Item No 1 but for fan / fresh Air fan point As per PS No. 133 ( C )& 187(A) (GST shall be paid extra)

Same as Item No 1 but for Plug point. As per PS No. 134 ( C )& 187 (C ) (GST shall be paid extra)

Same as Item No 1 but for call bell point. As per PS. No. 135 (C )& 187(E) (GST shall be paid extra)

Same as above but for two way light point. As per PS. No. 132 (C ) &187(B) (GST shall be paid extra)

Computer Point. As per PS. No.Analsis Rate (GST shall be paid extra)

S/F of Power Plug with 20 A/250 Volt flush type modular Switch & 5 pin 20 A/250 Volt flush type universal modular socket switch on conclead M.S. box including supply of all mterial labour etc.As per PS. No. 1139(A) (GST shall be paid extra)

Wiring Point for Ex-Fan with 1.5 sqmm FRLSH PVC insulated multistrand single core copper conductor cable in PVC Condumit complete in all Respect With Moduler Type Switch. As per PS. No.137 (C )187(D) (GST shall be paid extra)

Same as Above But I/C 200 Amp MCCB O/G 100 Amp. MCCB-2 Nos. Cat. B. Pannel Cubicle Type. As per PS. No. 812 (a ii) (GST shall be paid extra)

S & F surface/Flush mounting 4ways TPN distribution board with additional metal door without MCB complete in all respect,as directed at site by Engineer in charge. As per PS. No. 1026 (A) CAT A (GST shall be paid extra)

S/F Of 80-100 Amp 4Pole MCB(16 KA) C Curve. As per PS. No. 1021 CAT A (GST shall be paid extra)

S/F 63 Amp DP MCB (10 KA) C Curve. As per PS. No. 1011 Cat A (GST shall be paid extra)

S/F surface /fiush mounting 8 way SPN D.B with addditional board metal door without MCB complete in all respect.As per PS No. 1024 (A) (GST shall be paid extra)

S/f of 6 to 32A SP MCB(10kA)cbcurve. As per PS. No. 1002 CAT (A) (GST shall be paid extra)

Supply and fixing of recess/Surface mounting round 18 Watt to 20 Watt , Cut out Min 150mm, Height Min 40mm,, LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set, suitable for 24Hr Continuous Operation, Compelete in all respect.1980-2200 system lumens, 110lm/W, PF>0.95, THD <10% at full load, CRI>80, with 5 year warranty. As per PS. No. 1403 (GST shall be paid extra)

Supply and fixing of 2'x2' 36Watt to 46 Watt, Indoor Recess/Surface mounting LED Square Fitting for Armstrong Ceiling Powder quoted CRCA housing body diffuser of Special Polycarbonate meterial and driver set complete in all respect 3960-5060 system lumens, 70mm height with fully covered diffuser type, 110lm/W, PF>0.95, THD <10% at full load, CRI>80, with 5 year warrantee.As per PS. No. 1406 (GST shall be paid extra)

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. surface & suspended complete in all respect 2420 system lumens 110 lm/w PF>0.95, THD<10%, CRI>80, Sheet Thickness 0.8mm, Tube with aluminium heat with 5 year warranty. As per PS. No. 1413 (A) (GST shall be paid extra)

S/F of call bell of approved make on polished MDFED / Teak ply board including making connections etc.As per PS. No. 1101 (GST shall be paid extra)

Supply and wiring of 4 number 16 sq. mm. PVC insulated 1100 V grade single core Copper conductor cable in 40 mm dia PVC conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with two number 10 sq mm single core Copper conductor cable as earth continuity wiredrawn in coudit including matching colour wash etc, complete in all respect.As per PS. No. 291 (L ) (GST shall be paid extra)

Supply and wiring of submain with two number 10 sq.mm.FRLSH PVC insulated 1100V grade multistrand single core copper conductor cable in 25 mm dia heavy pvc conduit concealed with 6.0 sq mm one no FRPVC insulated multistrand single core cu. conductor cable as earth wire complete in all respect. As per PS. No. 218 ( C) (GST shall be paid extra)

S/w of submain with two no 6 Sq mm FRLSH PVC insulated 1100 V grade multi stand single core copper conductor cable in 20 mm dia pvc conduit concealed with 4 sq mm one no FRPVC insulated multistrand single core cu. conductor cable as earth wire complete in all respect. As per PS No. 220 (C ) (GST shall be paid extra)

S/w of submain with two no 4 Sq mm FRLSH PVC insulated 1100 V grade multi stand single core copper conductor cable in 20 mm dia pvc conduit concealed with 2.5 sq mm one no FRPVC insulated multistrand single core cu. conductor cable as earth wire complete in all respect. As per PS No. 216 (C ) (GST shall be paid extra)

S/w of submain with two no 2.5 Sq mm FRLSH PVC insulated 1100 V grade multi stand single core copper conductor cable in 20 mm dia pvc conduit concealed with 1.5 sq mm one no FRPVC insulated multistrand single core cu. conductor cable as earth wire complete in all respect. As per PS No. 1304 (C ) (GST shall be paid extra)

Supply and burring of Safe Earthing Electrode T-19 Zn-Zinc Coated, Length 3000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6, terminal Dia 12 mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 x 3 G.I. Strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified.As per PS No. 726 (B) (GST shall be paid extra)

S&L of 25 mm X 3 mm G.I. Strip from earth electrod in the ground as required complete in all respect. As per PS No. 716 (GST shall be paid extra)

S/f of electronic fan regulator with 120-280v modular type rating exiting on switch board including making connection etc complete in all respect. As per PS No. 1203 (A) (GST shall be paid extra)

S/F of fire bucket round botton of GI sheet 9-11 litre capacity duty painted as per fire brigade design initially filled with sand and water.As per PS No. 1133 (GST shall be paid extra)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 400Sqmm 31/2 Core As per PS No. 501 (t) (GST shall be paid extra)

150 Sq mm 31/2 Core As per PS No. 501 (p) (GST shall be paid extra)

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc (i) 400 sq. mm 3-1/2 core As per PS No. 503 (t) (GST shall be paid extra)

(i) 150 sq. mm 3-1/2 core As per PS No. 503 (p) (GST shall be paid extra)

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. (i) 400 sq. mm As per PS No. 504 (k) (GST shall be paid extra)

(ii) 240 sq. mm As per PS No. 504 (m) (GST shall be paid extra)

(iii) 150 Sq mm As per PS No. 504 (k) (GST shall be paid extra)

(ii) 95 sq. mm As per PS No. 504 (i) (GST shall be paid extra)

S/F Of Sheet Steel Enclosure Surface/Flush Mounting Fitted With 20Amp. 2Pin And Earth Metal Clad Scraping Earth Plug And Socket Complete In All RespectWith MCB. As per PS No. 1031+ 1002 CAT A (GST shall be paid extra)

S/F danger board fabricated from 10 gauge M.S.sheet as per I.E. Rules.As per PS No. 1109 (GST shall be paid extra)

S/F of single LED light wall bracket 6 to 8 watt on matching M.D.F.E.G. board board base etc. completein all respect.330-660 system lumens, 110lm/W, PF>0.95, with 5 years warranty. As per PS No. 1401 (GST shall be paid extra)

S&F of 630 Amp. four pole change over switch on 50mm x 50mm x 6mm angle iron frame, including the cost of labour, T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge. As per PS No. 383 (GST shall be paid extra)

S/F of 1400 VA UPS with 150 AH Tubler Battery As per MR (GST shall be paid extra)

Add for Invertor Wiring in wiring Point for light/ Fan/ Plug with 1.5 mm Cu Wire. As per PS No. 189 (A) (GST shall be paid extra)

Supply of Ceiling Fans with fan motor of A.C Permanent insulation, capacitor rating conforming BEE 5 Star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated voltage 220/240 volts, 50Hz,1-ph AC the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system. As per PS No. MR (GST shall be paid extra)

S/F of 300 mm Fresh Air Fan As per MR (GST shall be paid extra)

External Electrification Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130mm and base plate12mm thik) having 3mm thikness with on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. As per PS No. 641 (GST shall be paid extra)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (i) 16sq.mm 3-1/2 core. As per PS No. 501 (I) (GST shall be paid extra)

Supply and burring of Safe Earthing Electrode T-19 Zn-Zinc Coated, Length 3000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6, terminal Dia 12 mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover &masonary housing. (From electrode terminal to switch board, cost of 25 x 3 G.I. Strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. As per PS No. 726 (B) (GST shall be paid extra)

Supply & fixing of LED Street light Fitting having die cast aluminium body and diffuser/ Reflector with driver set suitable for 90- watt. Confirming to IP 66 protection complete in all respect.As per PS No. 1423 (GST shall be paid extra)

Supply and Wiring of submains with 2 nos. of 4 sq.mm.FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable for LED connection supply of all material labour and T&P required for proper completion of the work. As per PS No. 289 (B) (GST shall be paid extra)

Supply and fixing of brass nickel plated compression gland for PVC insulated &armoured served sheathed , underground cable including rubber ring etc. complete in all respect. (i) 16sq.mm 3-1/2 core. As per PS No. 503 (C ) (GST shall be paid extra)

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect.(d) 16 sq.mm 3-1/2 Core. As per PS No. 504 (d) (GST shall be paid extra)

Supply and laying of 25mm x 3mm G.I. strip from earthelectrode directly in the ground as required complete inall respect. As per PS No. 716 (GST shall be paid extra)

Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN,complete in all respect.40 A SPN. As per PS No. 807 (C ii) (GST shall be paid extra)

Direct Expansion air-conditioners with inverter technology Supply & installation of split Direct Expansion air-conditioners suitable for operation on A/C supply single phase 50 Hz 230Volts with hermetically sealed compressor with air cooled condenser with DC inverter technology, motor capacitor and start run capacitors, relay and over load protector internal unit , with one indoor and one outdoor unit. The condenser unit will be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube. (High wall chorded/cordless) suitable capacity 3 core sheathed/ PVC copper cable and a battery operated wireless remote unit. 1.5 TR, BEE Star Rated : 5 Star, EER 3.4 As per 1504B (i) (GST shall be paid extra)

4KVA Volatge stablizer For Air Conditioner Upto 1.5TR (130-300 Range) Copper Winding. As per MR (GST shall be paid extra)

Supply and Installation of MS Stand for Out Door Unit. As per MR (GST shall be paid extra)

SITC Of Suction/Dischage Copper Pipe Line In Split A.C Unit 1.5 Ton Capacity Including Brazing, Nitrile, Rubber Insulation 6mm Thick Class ;O' etc Complete 1/4'' (6.40mm) And1/2'' And 5/8'' (12.70mm). As per MR (GST shall be paid extra)

S/I Of Heavy Duty PVC Plastic Braided 20mm OD Flexible Pipe For Condensed Water Drain With Clipping Accessories Complet. As per MR (GST shall be paid extra)

S/F Of 2.5Sq mm4 Core Round Cable For A.C Connection Indoor/Outdoor. As per MR (GST shall be paid extra)

S/F Of2.5Sq mm3 Core Round Cable For A.C Connection Indoor/to stablizer/ Power Point. As per MR (GST shall be paid extra)

DG SET ITEMES KIRLOSKAR 58.5 KVA 3PH DG set 50HZ with Engine Model 4R810ETA 4G1& coupledwith KG-make Alternator Water Cooled withAMF Panel, Acoustic Enclosure & Base frameas per CPCB IV +norms with fuel tank &piping (For detailed product specificationkindly refer Annexure 2). As per MR (GST shall be paid extra)

Making RCC Platform (Size 3mX2m )as per the direction of Engineer Incharge.As per MR (GST shall be paid extra)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade 100 Sq mm 3-1/2 core complete with end termination with glands & lugs.As per MR (GST shall be paid extra)

S&F of 100 Amp. four pole change over switch on 40mm x 40mm x 6mm angle iron frame, including the cost of labour, T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge. As per MR (GST shall be paid extra)

Supply and burring of Safe Earthing Electrode T-19 Zn- Zinc Coated, Length 3000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6, terminal Dia 12 mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonary housing. Make: As approved in U.P. P.W.D., & C.P.R.I. Certified.As per MR (GST shall be paid extra)

Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. As per MR (GST shall be paid extra)

CC TV CAMERA - IP BASED HD CAMERA SITC of Indoor Hdbullet camera with IR with 1/2.8-inch CMOS, 2MP, Sensor pixels 1920 x 1080 with IR LED @ 20mts, Sensitivity-0.011x (color), 0. 1x (mono), H.26 (MP): M-JPEG video compression, Motion, tamper, Dynamic range, White balance, BLC, Privacy Masking, Fixed 4.0 mm lens, with al necessary fixing accessories. As per MR (GST shall be paid extra)

SITC of Indoor 11D dome camera with IR with 1/2.8-inch CMOS, 2MP, Sensor pixels 1920 x 1080 with IR LED @ 10mts, Sensitivity-0.01 1x (color), 0.01x (mono), 11.264 (MP): M-JPEG video compression, Motion, tamper and audio detection, Dynamic range. White balance, BLC, Privacy Masking, Fixed upto 3.0 mm lens, etc with all necessary fixing accessories. As per MR (GST shall be paid extra)

NETWORK VIDEO RECORDER Supply, installation, testing & commissioning of 24 channel Network Video Recorder with storage drive providing storage of 1 month.As per MR (GST shall be paid extra)

NETWORK COMPONENTS Single Port Face Plate on wall with neccesary fixing accessories.As per MR (GST shall be paid extra)

CAT 6 Patch Cords - 5M length at rack side. As per MR (GST shall be paid extra)

CAT 6 Patch Cords - 2M As per MR (GST shall be paid extra)

CAT 6 POE Patch Panel- Fully Loaded As per MR (GST shall be paid extra)

8 Port POE SWITCH As per MR (GST shall be paid extra)

Supplying, installing-testing and commissioning of Workstation PC: Intel(R) Core Processor Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1X4GB) Non-ECC DDR3 1600MHz SDRAM Memory: Keyboard: 12 function Keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20"TFT Monitor, Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit Ethernet LAN 10/100/1000; Hard disk: 250GB, 720 RPM 3.5" SATA 6Gb/s Hard Drive: Operating system: Windows 7 Professional 64 Bit. AOR As per MR (GST shall be paid extra)

Supplying- installing, testing and commissioning of Full hd 42" LED Display Panel. As per MR (GST shall be paid extra)

ACTIVE COMPONENTS Supply, installation and testing of 24 port L2 10/100 Base-T Fully managed switch, with 22Nos autosensing 10/100 Base-T port and 2 Nos Dual-personality SFP port, Switch Should be life time warranty till the customer own. (per block each and gate). As per MR (GST shall be paid extra)

NETWORK RACK 1U Wall Mountable powder coted Rack with 3x5A Power Manager., 1 position fan, min 1 nos of shelf, Front Glass door with Lock & Key as respective floor WxDxH (600 x 450 x 635mm). As per MR (GST shall be paid extra)

24U, 600 X 1000 mm floor Mountable powder coated Rack with 6x5A Power Manager, 2 Horizontal Cable Manager, 4 position fan, min 3 nos of shelf, Front Glass door with Lock & Key at IBMS room. As per MR (GST shall be paid extra)

COMMUNICATION CABLE Cat 6 copper flexible shielded cable for communication in 20mm dia steel conduit.(MR) As per MR (GST shall be paid extra)

SITC of M.S. black pipe"C"Class (Is 1239/3589 including Cutting,welding etc & providing suitable flanges along with necessary fitting viz,bends tees etc & anti corrosive Treatment Make-Jindal/Qst/Haryana/Tata 100 mm Dia As per PS No. A(iii) (GST shall be paid extra)

80 mm Dia As per PS No. A (iv) (GST shall be paid extra)

50 mm Dia As per PS No. A (v) (GST shall be paid extra)

SITC of C.I.Double flanged Butterfly Valve complete with Nuts,bolts & washers etc.conforming IS 780 Make:Kalpana/Aarko/Sir/Kartar/Kirloskar 100 mm dia As per Quot. (GST shall be paid extra)

80 mm dia As per PS No. A 18 (i) (GST shall be paid extra)

SITC of Cast iron double flanged non return Valve complete with Nuts,bolts & washers etc.conforming IS 780 Make:Kalpana/Aarko/Sir/Kartar/Kirloskar 100 mm dia As per Quot. (GST shall be paid extra)

SITC of C.I.Double flanged Sluice Valve complete with Nuts,bolts & washers etc.conforming IS 780 Make:Kalpana/Aarko/Sir/Kartar/Kirloskar 150 mm dia As per PS No. A 17 (i) (GST shall be paid extra)

SITC of first aid hose Reel drum with 20 mm dia, 30 meter long rubber pipe shut off nozzle, 25 mm dia gate valve complete confirming to is:884/444. Make:Safeguard/Lifeguard/new age/Agni. As per PS No. A2 (GST shall be paid extra)

Supplying Installation testing & Commissioning of 25 mm Air Release valve gunmental having rubber ball and with 25 mm BSP threaded male inlet including necessary accessories and connections complete in all respect.As pr Quot. (GST shall be paid extra)

Supplying Installation testing & Commissioning of SS/GM/Ball Valve 25 mm dia complete. As per Quot. (GST shall be paid extra)

SITC of Hose Box of 18 SWG MS Sheet with glass fronted door to accommodate 2 nos RRL hose & 1 nos SS Branch Pipe with nozzle (Internal) Make.Safeguard/Lifeguard/new age/Agni. As per PS No. A-6 (GST shall be paid extra)

SITC of RRL hose 63 mm dia 15 Mtr long complete with SS coupling conforming to IS 636. Make: Safeguard/Lifeguard/New Age/Agni/Primear As per PS No. A-4(GST shall be paid extra)

SITC of SS Branch pipe with nozzle 63 mm dia conferming to IS:903 .Make:Safeguard/Lifeguard/New Age/Minimax/Agni. As per PS No. A5 (GST shall be paid extra)

SITC of Electric Driven Terrace Pump of 450 LPM with minimum pressure of 2.0 kg/cm2 complete installation with concrete faondationand suitable base plate by iron channel complete work as per requirement Make : Kirloskar/Mather&Platt/other standard make. As per PS No. A11 (GST shall be paid extra)

SITC of Air cushin tank assembly 200 mm dia 1.5 mtr long with air release valve,pressure gauge & accessories complete in all respect. As per PS No. A 8 (GST shall be paid extra)

Supply Installation testing and commissioning of Pressure Gauge. As per PS No. A-21 (GST shall be paid extra)

SITC of GM fire brigde 4 way inlet connection 63 mm dia.Make Lifegaurd/Safex/Minimax/Newage/Agni. As per PS No. A-15 (GST shall be paid extra)

SITC of Automatic panel of tarrace pump suitable for 5 HP tarrace pump. As per A-14 (GST shall be paid extra)

Supplying Laying testing & Commissioning of 2 corex 1.5 sq.mm single standard copper conductor, PVC insulated armored cable.As per PS No. B-9 (GST shall be paid extra)

S/L of Aluminium conductor PVC insulated sheated cable 100V grade as per PWD specification. 16 sqmm 4 core As per PS No. 501 (i) (GST shall be paid extra)

S/F of Brass Nickel plated Lugs 16 sqmm 4 core As per PS No. 504 (d) (GST shall be paid extra)

SITC of Pressure Switch As per PS No. A-20(GST shall be paid extra)

SITC of single headed S.S hydrant valve comprising of 80 mm dia flanged bend 63 mm dia SS oblique pattern landing valve complete with blank cap etc. Make: Safeguard/New Age/Lifeguard/Agni/Minimax/Safax. As per PS No. A-3 (GST shall be paid extra)

Supply, Installation, Testing & Commissioning of Terrace PVC tank having capacity 5000 Ltrs. As per Quot. (GST shall be paid extra)

ALARM SYSTEM. SITC of 6 zones fire alarm panel in compatile to existing fire alar system completed with visual indications of short circuit fault, open circuit fault, fire conditions and all other standard facilities, zone covered complete with all connections etc complete as reqd.( Make-Agni, System Sensor, Ravel). As per PS No. B-5 (GST shall be paid extra)

Supply, installation, testing and commissioning of Ionization Smoke detector as per fire specification including making connection with wire complete in all respects.(Make- Apollo, Agni, System sensor). As per PS No. B-7 (GST shall be paid extra)

Supply, installation, testing and commissioning of Manual call points breck glass type housed in MS sheet, including connection complete in all respects.(Make-Agni, Ravel, System Sensor). As per PS No. B-1 (GST shall be paid extra)

Supply installation testing & commissioning of electronic hooter housed in MS housing suitable for wall mounting/ celling including making commection etc Complete as reqd.(Make-Agni, Ravel, System Sensor). As per PS No. B-2 (GST shall be paid extra)

Supplying Installation testing & Commissioning of Response Indicater complete with base as required. As per PS No. B-6 (GST shall be paid extra)

Supplying Laying testing & Commissioning of 3 corex 1.5 sq.mm single standard copper conductor, PVC insulated armored cable. As per PS No. B-14 (GST shall be paid extra)

Supply & fixing of CO2 type fire extinguisher, 4.5 kg. capacity (ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. As per Quot (GST shall be paid extra)

M/S SWATANTRAVEER