ADDN/ALTN AND IMPROVEMENT TO MAP PKT-I AT BLDG P-318 (03 DUS) AND PROVN OF QTY 02 SPLIT AC OF 2 TON CAPACITY AT POWER ROOM AT AFNET SITE-I AT HQTC (U) BANGALORE

Amount

Demolition Stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking out/ down old existing water proofing treatment of sunken slab including cleaning the old RCC surface of sunken/lowered portain of slab surface to full depth of sunken floor by wire brush or chisel out any mortar sticking the surface and made suitable to receive water proofing treatment. The surface shall be clearned and prepared in such a was to provide sound base, free from any oil, grease, dust or deleterious material which may impair adhesion of water proofing treatment. The surface preparation shall be carried out mechanically to remove contaminant, laitance and weak concrete to expose blow holes and to produce a sound concrete with adequate profile and porosity. Any creak shall be treated with cementitious repair mortar of Forsroc, Renderoc CS or epoxy creak filling mortar or equivalent product by proper grooving method as per manufacturer,s instruction and as directed by the Engineer-in-Charge.

Preparing the inside surface of core and PVC by roughening using suitable file to get better adhesion prior to bore packing (for reinstallation). Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Providing necessary formwork for packing the bore using suitable arrangement (depending upon site conditions). Applying a coat of styrenebutadiene based polymer coating using Nitobond SBR or equivalent product of Asian paints, M/S MC Bauchemic /CIPY/SIKA/Pidilite Dr Fixit/ Thermax/ STP admixed with integral WPC or cementitious crystalline waterproofing compound to enhance adhesion between the packing material and other surfaces. Packing the gap using nonshrink cement polymer-based grout using conbextra GP2 upto the surface of the bore whilst the Nitobond SBR is in tacky state. The above analysis is based on assumption for 150mm diameter core with 110mm diameter PVC for 5” thick slab only. Typical Properties Compressive strength at 28day as per BS 1881 45N/mm2, completely as per the manufacturer’s Instruction.Nos 450

M & L Making coving of 50mm X 50mm at all the flat & vertical junction using Fosroc Renderoc S Single component, shrinkage compensated, fiber reinforced, thixotropic cementitious mortar, to achieves a minimum compressive strength of 20 MPa in 1day and 55 MPa in 28days when tested as per EN 12190 and capable of applying 50mm thickness in single layer of approved product finished flush with existing surface.

M&L for water proofing treament by using water proofing membrane as sepecified herein after. Supply and application of single-component, Pitch free seamless roller/spray applied Nitoproof 600PF or equivalent product of Asian paints, M/S MC Bauchemic /CIPY/SIKA/Pidilite Dr Fixit/ Thermax/ STP applied at average minimum DFT of 1.3 mm above primed surface with Nitoproof WB Primer or equivalent product of Asian paints, M/S MC Bauchemic /CIPY/SIKA/Pidilite Dr Fixit/ Thermax/ STP It shall possess the following properties: Solids by Volume: 85%, Tensile Strength ASTM D412: >1.9 MPa, Tear resistance ASTM D624C: 15(N/mm), Elongation ASTM D-412: >400%, Adhesion in-peel test ASTM C836 (N): > 50N Note: Providing a non-woven geotextile fabric of 200GSM over the cured waterproofing membrane before going for a protective layer. ( Note 1 : Fill the sunken with water and check for dampness and seepage . All pipes passing through walls of sunken floor shall be laid before water proofing treatment is carried out . One No 50 mm dia, 35 mm long medium grade GI pipe with wire gauge on inside mouth shall be provided to each sunken portion.Cost of pipe with including of quoted rate , no extra cost will paid) (Note 2: The work shall be carried out complete as per manufacture's specifications and application methodology. Execution to be done with authorized trained/skilled applicator with prior experience of more than 5 years in applying similar system and as per manufacturer technical guidelines laid by manufacturer,

M&L for PCC type D2 ,1:4:8 (Using 40 mm graded stone aggregate) as in foundation /sunken portion filling and mass concrete

M&L for 25 mm thick PCC (1:2:4), type B0 (Using 12.5 mm graded stone aggregate) as in flooring, rough finish surfaces for receving top layer.

M&L for 75 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) for hard standing including finishing the surface even and fair complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4), type B0 (Using 12.5 mm graded stone aggregate) as in flooring, all as specified and directed.

M&L for Forming Contraction (Dummy) joints 75mm deep x 10mm wide, filled with sealing compound, grade 'A' all as specified and directed.

M&L for vitrified ceramic coloured tiles 8 to 10mm (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm double charged light shade as in floors etc set and jointed neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in (CM 1:6) coloured and shade as approved by GE complete all as specified and directed.

M&L for vitrified ceramic coloured tiles 8 to 10mm thick area of each tiles not exceeding 0.36 sqm double charged light shade as in skirting height 10 to 15 cm set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including a backing plaster 10mm thick in CM (1:4) coloured and shade as approved by GE all as specified.

M&L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tiles exceeding 0.11 sqm but not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/ coloured cement to match complete all as specified.

M&L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tiles exceeding 0.11 sqm but not exceeding 0.36 sqm as in wall skirting etc. set and jointed in neat cement slurry over and including 10mm thick rendering of CM 1:4.

M&L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/ coloured cement to match all as specified.

M&L for Coloured Glazed ceramic design tiles 600X 300X 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick rendering in cement morter (1:4)

M & L for Granite (of any type) tiles 18-20 mm thick [table rubbed and polished] machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone in as in flooring and landings of stair case, treads including cutting and polishing of tiles and 20 mm thick screed bed of cement morter (1:6) complete.

ditto as above but vertical surfaces with 10 mm thick rendering of cement morter (1:4) complete.

M&l for rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations

Taking down of chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frames) and set aside or removing from site.

Taking down of chowkats or frames exc 1.5 sqm but n. exc 4 sqm each (without taking off shutters from the frames) and set aside or removing from site.

Taking down shutters of any description exceeding 1 Sq. M but not exceeding 2 Sq. M each

Taking down shutters of any description exceeding 1 Sq. M but not exceeding 2 Sq. M each and refixing in same opening after easing and adjusting all as specified and directed.

Dismantling boarding, any description, fixed in any position with fixed with screws etc

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in unframed work, in any position.

Dismantling Aluminium work including doors, gates, partation frame or shutter and similar works etc.complete, all as specified and directed.

S&F Pressed steel frames size 125x60 mm for doors with one or more rebates including necessary fixing lugs,125mm mild steel butt hinges, medium weight, lock strike plate, etc complete, all as specified and directed.

S&F Pressed steel frames size 105x60 mm for doors with one or more rebates including necessary fixing lugs, 125mm mild steel butt hinges, medium weight, lock strike plate, etc., complete, as specified,

S & F 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.

S&F 35 mm thick factory made 2nd Class Hard wood Glazed and skeleton shutter open rebated and prepare to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc, size of members of shutters all as specified.

S&F in repairs Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory Made Solid PVC Moulded Door Shutter,with particle board core , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

M&L 2nd class hard wood Plain fillets. square, rectangular or triangular, exc 13 Sqcm & n. exc 25sqcm in section, clean sawn, secured with screws all as specified and directed..

S & F 18 mm thick veneered decorative plywood, grade 1( with BWR resin), with decorative faqce veneers on both faces fixed with screws to timber frame work for built in cupboards, shelves, almirahs etc all as specified and as directed by Engineer in Charge.

S&F Powder coating (minimum thickness of powder coating 50 micron) aluminium frame for partition, doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as direction by Engr in Charge.

S&F Powder coating (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 1.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F Powder coating (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, sliding /side hung type without sash bars, aluminium sections weighing not less then 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and as direction by Engr in Charge..( Note : sheet Glass and SS wiremesh shall be measured & paid separately). .

S&F in stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including beads all as specified and directed

S & F 4.8 mm thick sheet glass ordinary quantity and glazing with oil putty in squares not exceeding 0.50 sqm in each pane.

S&F sheet glass, of 4mm thick ordinary quality, ground or obscured or frosted, on one side in square n.exc 0.5 Sqm in each pane.

S & F Brass Godrej Mortice lock, vertical type, size 100 mm 4 levers include for escutcheon plates and two keys in repairs.

S & F Stainless steel clip on auto closing panel concealed hinges thickness 15-22 mm for full overlay door 0 degree crank for cupboard door all as specified and as directed.

S & F 30 mm width of flaps (when open) Continuous (piano) hinges, mild steel, bright finish or electrogalvasised all as specified and as directed.

S&F magnetic ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed all as specified and directed by engineer in charge.

S & F 125 mm mild steel butt hinges, medium weight, cold rolled incl welding to pressed steel chowkats etc.

S & F 200 mm alluminium anodised barrel tower bolts of stove enameled black, with bright bolt and fixed.

S & F 150 mm long extruded aluminium alloy handles, fabricated type, anodised.

S & F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S & F 300 mm size mild steel rat tail rod pattern springs including roller and roller plate complete.

S&F in 140mm long floor door stopper of brass body and tongue, anodised, with hard drawn steel spring,

S&F Butt hinges, stainless steel, 100mm size, ISI marked, complete all as specified & directed.

S&F for 150 mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 125mm Aluminium handles, fabricated type, anodised.

S&F 150mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S & F stainless steel self closing auto hinges for wooden cabinet shutter complete all as directed

S & F stainless steel telescopic channel ball bearing drawer channel 500 MM with loading capacity: 45Kgs complete all as directed

S & F 100 mm long Extruded brass handles, fabricated type CP polished with brass screws complete all as directed.

S & F CP Stainless Steel (SS 304) wire basket drawer of size 420 x 485 x100 mm (Cuttlery Box ) Make: Hettich / Godrej/ Kutchina (Cup and Soucer rack )

S & F CP Stainless Steel (SS 304) wire basket drawer of size 420 x 485 x150 mm (Cup and Soucer rack ) Make: Hettich / Godrej/ Kutchina

S & F CP Stainless Steel (SS 304) plain wire basket drawer of size 420 x 485 x 200 mm Make: Hettich / Godrej/ Kutchina

S & F in repairs Powder coated fancy type Stainless Steel curtain rod 25mm dia with suitable SS brackets with suitable woodenround base and fency type end top matching to curtain rod of make as approved by GE all as specified and as directed. [ Additional supporting bracket shall be provided if length is exceeding 1.2m and rate quoted shall include for the same ]

Dismantling structural steel work including doors, gates and similar works but excluding framed truss etc.

M & L for Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 height all as specified and direction by Engr in Charge.

S & F Mild steel flats (40x6mm thick) for hand rails, wind ties, posts and struts in fencing screwed or welded to shape as directed, including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 410 - O or Fe 310 - O

Cutting holes exc 100 sqcm but n.exc 250 sqcm into or through cement concrete slabs, chajjas, etc. reinforced or otherwise

M&L for Plain Cement Concrete Type B0 , 1:2:4 (using 12.5 mm graded stone aggregate) cast in situ in cills and other similar bands, plinth courses, parapets, copings, hold fast ,bed plates ,filling hollow section of pressed steel frame and the like including use and waste of form work,weathering, slightly rounded or chamfered angles and throating as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc., all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks type C1, 1:3:6 ( 20 mm graded aggregate) exc. 10 cm in width and setting in mortar 1: 6 , complete all as specified.

M&L for Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type C1, 1:3:6 ( 20 mm graded aggregate) and setting in mortar 1: 4 , complete in walls all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. all as specified and direction by Engr in Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement. including mixing of water proofing compound wherever required as per manufacturers instructions and as direction by Engr in Charge (WPC shall be measured & paid separately). .

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6, finished even and smooth with out using extra cement. all as specified and direction by Engr in Charge.

M&L fo Rendering 10 mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling of chajja,roof projection,shelve etc and finished even and smooth without using extra cement all as specified and direction by Engr in Charge.

Supply only liquid water proofing compound of approved quality. (Make : CICCO NO.1/SIKA/ACCO PROOF).

M&L for preparing new plastered surfaces and applying three coat of white wash on surfaces of ceilings all as specified and direction by Engr in Charge.

M&L for preparing old plastered surfaces and applying two coat of white wash on surfaces of ceilings all as specified and direction by Engr in Charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint through mechanical means over a coat of alkali resistant primer on surfaces of walls all as specified and direction by Engr in Charge.

M&L for preparing old plastered surfaces and applying one coats of cement base paint through mechanical means all as specified and direction by Engr in Charge.

M&L for preparation of new plaster surface of wall and applying 2coats of distemper oil emulsion white or tinted through mechnical means over a coat of 1mm thick wall care putty, all as specified and direction by Engr in Charge.

M&L for preparation of old surface after complete removal of existing treatment and applying 2 coats of distemper oil emulsion white or tinted through mechnical means over and including a coat of 1mm thick wall care putty, complete all as specified.

M&L for French polishing on new works with two or more coats surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler all as specified and direction by Engr in Charge.

M&L for French polishing on old works with one or more coats surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and direction by Engr in Charge.

M&L for Preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) all as specified and direction by Engr in Charge.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxied priming all as specified and direction by Engr in Charge..

M&L Preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint all as specified and direction by Engr in Charge.

S&F tubes 15 mm bore, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down old steel tubing complete, all as specified and directed.

S&F tubes 20 mm bore, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down old steel tubing complete, all as specified and directed.

S&F tubes 25 mm bore, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down old steel tubing complete, all as specified and directed.

Dismantling water tanks exc 500 ltrs and n exc 1000 ltrs all as specified and directed.

Supply, hoisting, fixing in position and connecting incoming and outgoing pipes, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), triplelayer, complete all specified and as directed including dismantling existing water tank.

S&F in repairs 25mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe and fixed. (minimum weight 455 gms)

S&F in repairs 25mm gun metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed.

S & F in repairs 15 mm bore chromium plated fancy type long body bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S & F in repairss fancy type CP 2 way bib cock with wall flanges fixed as in repair all as specified.

S&F in repairs fancy type 15 mm bore angle stop valves, chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repairs premium quality 15mm bore central hole basin mixer with regular spout without popup waste system of make Jaguar, Cera, Somany or equivalent.

S & F in repairs Single lever cast copper alloy, chromoum plated HOT and COLD 15 mm dia Fancy type Wall Mixer complete all as specified and directed.

S&F CP health faucet including one mtr length SS conncting pipe all as specified of Make: jaguar or equivalent fixed in repairs

S&F in repairs Brass chromium plated shower rose 125mm size with 300 mm long stainless stelel arm including fixing to steel pipe or union all as specified.

S & F in repairs PVC connection 15mm size 450mmlong with CP PTMT nuts all as specified.

S & F in repairs Corner Glass Shelf, Fancy Type complete all as complete all as specified and as directed.

S & F in repairs PVC body cabinet box mirror of size 350 mm x 450 mm x 100 mm in PTMT alloy of approved patterns and designs fixed in repairs after taking out the old cabinet complete all as specified and as directed.

S & F in repairs Brass chromium plated tubular towell rail 20 mm dia , D type , 600mm long between flanges fixed with & incl chromium plated brass screws and wooden /plastic cleats

S&F in repairs fancy type wall mount SS-304 premium grade stainless steel soap holder/stand size 11.5(l) x 8.5(b) x 5.5(h) cm fixed with and including Chromium plated brass screws and wooden/plastic cleats.all as specified and directed.

S&F in repairs Tumbler holder Make-jaguar Code No-ACN-CHR-1141 N or equailent.

S&F in repairs Toilet roller holder with flap of Make-jaguar Code No-ACN-CHR-11535 or equailent.

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand.

S&F in repairs standard PVC waste pipe 32mm dia.,complete for WHB.

S & F in repairs 32 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160m

S & F in repairs Stainless steel kitchen plate rack of size 750mm x 600mm x 250mm, made of 1mm thick stainless steel sheet complete all as directed. [Make: Prayag/ Nirali/ Jayna/ Neelkant]

S & F in repair Vitreous china wash down water closet (Pedestal pattern, ETWC), white (including fixing bolts, Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed.

S&F in repairs PVC (SWR) 'P' or 'S' trap 110mm bore.

S&F in repairs PVC (SWR) floor trap 75 mm diameter of outlet , with or without waste hole with grating including jointing with solvent cement complete all as specified & directed.

S&F in repairs PVC Flushing cistern 10 Ltr capacity valveless syphonic action type low level, white, with inlet ,ball valve float and handle including brackets and flush pipe all as specified and directed.

Taking down rain water pipes including all fittings any size and pattern. upto 10th storey floors.

M&L for 75 mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to floor/walls all as specified and directed. .

M&L for 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed. .

M&L for 150 mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls as rainwater pipe.

S & F in 75 mm dia.,PVC Bends with access door all as specified and directed

S & F in 110 mm dia., PVC Bends with access doorall as specified and directed

S & F in 150 mm dia., PVC Bends with access doorall as specified and directed

S&F in 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S&F in 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S & F in 110 mm dia.,vent cowl in repairs all as specified and directed.

Removing demolished material i.e. building materials, concrete, stone masonary, debris, tree roots, trunk, branches of any size etc. to a distance of 30Km or beyond, out of premises of metropolitan area, including loading, unloading by manually or by mechanical means (JCB) and to be transported through tractor-trolly or tipper and stacking at the destination as and when directed by Engineer-in-Charge during execution.

Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc.

Material & Labour for taking out existing ceiling fan from the old location of any capacity & repair refixing all as directed

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers.

Point wiring complete with Multi stranded copper conductor size 1.5 sqmm PVC insulated, unsheathed,FRLS cable , 1100 volts grade conforming to IS 694 multistranded , drawn in and including rigid PVC surface type conduit Concealed in walls/ floors/ ceiling etc with and including fixing of metal flush boxes of suitable size and modular white plate with frame for mounting of fittings, modular type switches, regulator and also including 1.5 sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly,cutting chasis to the wall s/ floors/ ceiling and repairing with existing surface after work ,complete all as specified and directed.

One 3 pin socket point 5 Amps on independent board.

All as per item No 135 here-in-before but using copper conductor 2.5 sqmm PVC insulated unsheathed FRLS cable with copper conductor size 2.5 sqmmm PVC insulated unsheathed continuous earth continuity for 3 pin 15 amps socket outlet independently.

Supply & fix ceiling rose surface backelite two to three terminal complete all as directed.

Supply & fix switch modular single pole 1 way 6 Amp 230 volt complete as directed.

Supply & fix switch modular single pole 1 way 16 Amp 230 volt complete as directed.

Supply & fix socket 6 Amps modular type, 230 volts complete as directed.

Supply & fix Socket 6A/16A - modular type 230 volts complete as directed.

Buzzer, Ding Dong AC. 230 volts, single pole.

Supply and fixing Modular Bell push 6A 1 module

Supply and fixing of modular type fan regulator upto 300 watts with 5 step speed control for fans any sweep 1200 mm/1400 mm.

Supply and fixing of modular white cover plate with frame, 3 module

Supply and fixing of modular white cover plate with frame, 4 module

Supply and fixing of modular white cover plate with frame, 6 module

Supply and fixing of modular white cover plate with frame, 8 module

Supply and fixing of metal flush box 3 module

Supply and fixing of metal flush box 4 module

Supply and fixing of metal flush box 6 module

Supply and fixing of metal flush box 8 module

Supply and fixing LED lights fitting 4 feet, 1 x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing lamp holder, PVC polycarbonate type with black plate suitable for batton/ angle fittings.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

Taking down & Refixing only geyser 50/25 ltrs capacity after repairs in new position including drilling holes on wall ,fixing four Nos anchor bolts,nuts and washers and connecting to the water and electric connections and testing complete all as directed.

M&L for sub main wiring complete with 2 runs of 4.00 Sqmm PVC insulated and unsheathed cable with multistranded copper conductor confirming to IS-649, 1100 volts grade and drawn through and including PVC non metallic rigid conduits and conduit accessories concealed / run on surface of wall/floors/ ceiling etc and connecting terminal ends including 1 run of 4.00 Sqmm of PVC insulated unsheathed copper conductor cable green colour as continuous earth continuity conductor and connecting to earth dolly including removing unserviceable sub main wiring complete all as directed and specified.

Supply and fixing in repair of DB, SPN 12 ways, Double door type

Supply & fix in repair MCB SPN 6 to 40 Amps 240 volts 10 KA rupturing capacity complete all as directed

Supply & fix in repair 'C' Curve MCB SP 6 to 32 Amps 240 volts 10 KA rupturing capacity complete all as directed

Cutting chasis, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc, for concealed conduit wiring into the stone walls built in cement mortar or cement lime mortar and walls of cement concrete suitable for housing 25mm dia conduit pipe using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed.

Cutting into or through the stone walls / brick walls built in cement mortar or cement lime mortar and walls of cement concrete suitable size for housing for sunk box using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed.

Supply , install and tesing of Cassate AC units indoor/outdoor complete with cordless remote control unit and with in built air filter for better indoor air quality with maximum star rating inverter model capacity 2.0 TR complete all as directed. Note: During errection of indoor unit at site necessary modification in false ceiling etc required shall be deemed to be included in the quoted rate.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA

M&L for submain wiring with two runs of PVC insulated multistranded copper conductor 4.0 Sqmm and one run of earth continuity conductor with PVC insulated multistranded 4.0 Sqmm copper conductor drawn in and including PVC casing & capping accessories laid on surface of wall/roof etc complete all as directed and specified.

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete.

Cutting hole into stone masonry wall not exceeding 450mm thick, built in cement mortar, using stone drilling machine for inserting 65mm dia (50.24 sqcm) PVC pipe including making good the disturbed surfaces all as specified and as directed.

S&F copper tubing for suction/ discharge line, for spilit type Ac suitable upto 2.0TR apacity complete all as specified and as directed

S&F wall mounting bracket, for spilit type Ac suitable upto 2.0TR capacity out door unit complete all as specified and as directed

S&F drain pipe for spilit type Ac s complete all as specified and as directed

N RAJEGOWDA and CO

Srinivas G Civil Contractor

Raghu M Contractor

M/s BHOOMI ELECTRICALS